3560 Interconnect Cable - Port Disabled b/c non-compliant GBIC

I purchased a CAB-SFP-50CM Catalyst Interconnect Cable to connect two 3560s. When the cable is plugged in, I receive the following error in the Cisco Network Assistant:
Description: Gi0/1: This port has been disabled because Non Compliant Gigabit Interface Converter (GBIC) connector detected.
Recomendation: Replace connector with cisco compliant Gigabit Interface Converter (GBIC) connector. Refer switch technical documentation to determine cisco compliant connector. Enable the port again.
Any help? I assumed this would be a "plug and play" installation. Re-enabling the disabled port doesn't seem to help.
Thanks in advance...

Thanks for the response - this is a Cisco branded cable:
Manufacturer: CISCO
Description: CATALYST 3560 SFP INTERCONNECT CBL 50CM
Part Number: CAB-SFP-50CM=
I thought I had done my research...according to the 3560 data sheet
(http://www.cisco.com/en/US/products/hw/switches/ps5528/products_data_sheet09186a00801f3d7d.html)
"These ports also support the Cisco Catalyst 3560 SFP Interconnect Cable for establishing a low-cost Gigabit Ethernet point-to-point connection."
However, it doesn't seem to work. Is it possible that I've got a defective cable, or is there something else that I need to do?
Thanks again.
Edited to add: the cable I have is pictured in the data sheet (Figure 2) and the switches I am trying to interconnect are model WS-C3560-48PS.

Similar Messages

CISCO CATALYST 3560 SFP INTERCONNECT CABLE

What is the advantage of using this SFP cable over a 1000BaseT GBIC and daisy chaining the switches together?
Just curious???
Thanks!

The advantage comes down to cost. Whether you can realize this advantage depends on the distance between the two Catalyst 3560 switches.
If the distance is less than or equal to 50cm, then one SFP Interconnect Cable (CAB-SFP-50CM=) at US$250 is a much less expensive way to connect the two switches than two 1000BASE-T SFP (GLC-T=) at US$395 each = US$790 plus a Cat5 or better UTP Gigabit Ethernet crossover cable.
If the distance is greater than 50cm but less than or equal to 100m, then the 1000BASE-T SFPs are your least expensive option. The alternative is MM or SM fiber.
If you have to connect a Catalyst 3560 SFP interface to another Catalyst switch that takes GBICs, then the SFP Interconnect Cable is not even an option. From 0 to 100m, 1000BASE-T SFP and GBIC (WS-G5483=) would be your least expensive way to go.
If there's any chance you will be redeploying these switches somewhere else in the future, you may want to put the 1000BASE-T SFPs in now. That way you'll already have them when you need them later.

Seeking what type & info for connector cable for W500 Digital or non-Digital Displayport to HDMI

Hello, I have purchased and waiting arrival of: Thinkpad W500 T9400 64Bit 4061-BV3 # xx-xxxxx Windows 7 Prof.
I'm not sure if the port is Digital or non-digital. I think the Lenovo site specs don't say "digital". But a review on internet talks about it being digital. Here is link to that. You scroll down page for photo of ports.
http://www.notebookcheck.net/Review-Lenovo-Thinkpad-W500-Notebook.11683.0.html
Anyone know what cable I need to get?
I want to watch movie played from laptop onto my tv. TV might be HD, but I don't care how movie comes up on screen, just so I can watch it. What would be cable type to get? I see that startech.com sells these things.
Also, I see lots talk here about Audio. If audio doesn't come through the TV, will it play through laptop?
Many thanks!
Massachusetts
serial number removed per forum rules richk

PLEASE DISREGARD THIS POST/QUESTION. I have obtained info from another Thread.
sorry.

Imac usb ports disabled and nothing is connected

iMac 27inch Late 2007 USB Ports Disabled Again!
Has happened before and took forever to fix it. Nothing specific fixed it last time and nothing I know was the direct cause. Each time different OS, different location, different year, different cables etc etc.
Now, reset everything, moved everything, changed everything - still nothing. No USB ports work. iMac still has pop up "USB devices disabled..."
Taking into Apple unless someone can tell me what 10 pages of google hasn't - what a bloody stress and waste of time!

Disconnect all peripherals from your computer.
Resetting your Mac's PRAM and NVRAM

USB port disabled by Palm sync

Got a new Palm, tried to sync with the USB cable connected to the port on my keyboard. Got the error: "port attached to is drawing too much power, will be disabled" after which the port would not function. Did I blow the hardware, or is this a protective mechanism that can be reset with software? Have since tried - hesitantly - on the main USB (2.0) ports on my iMacG5 and it has worked okay.
Jon

A reboot should bring back any ports disabled in that fashion.

Using time capsule model A1409 and trying to use it as only backup. Already have Verizon wireless router. Do not know which cable port to use in back of time capsule. And also it is asking for password. Have tried all of mine and it will not work.

Want to us my time capsule model A1409 as only backup. 2 TB hard drive.
Already have Verizon wireless router. Do not want to use Time capsule as router, only back up for iMac.
Do not know which cable port to use in back of time capsule to Ethernet port back of my iMac.
And also it is asking for password for the server John Garland's Time Capsule so Time machine can access it..
Have tried all of passwords can think of and none work.
Held the reset button for one second on back of capsule and do not see if anything happened.
What a conundrum.
Appreciate any help to get this working.
Thanks,
John R

I have a 2TB Timecapsule and really only use it for Time Machine backups. But the Wi-Fi side is used to sync my iPad at times.
Mine is wiredup thus;
Eth cable from iMac to modem (not the WAN port should you have one), then eth cable from modem to T/Cap in the WAN port (bottom port with an O sign above it)
I believe when its connected up you may have to set up a wireless network. Follow the instructions to set up Wi-Fi and Network
and then give it a password. The WiFi icon should appear in the menu bar where you can switch it on or off.
Its been sometime since I set it with the help of Apple Techs so I might be a bit rusty.
Alan

I have purchased a new iPhone on the online store, but how come Apple can send me an repacking old device (with scar on both the border and the cable port)!!!! And after I phone to their hotline for the issue, they asking to give me hk$400 cash coupons??

I have purchased a new iPhone on the online store, but how come Apple can send me a repacking old device (with scar on both the border and the cable port)!!!!
And after I phone to their hotline for the issue, they asking to give me hk$400 cash coupons???? This action make me very angry. I have pay for my goods, but they are giving me some repacking rubbish, and trying to treat me as a beggar????
I have make the request to give me back a new device in good conditions, I will wait and look for what they will delivery.

Do you feel better now that you have vented?
This is a user to user forum... if you want/need assistance, contact Apple directly.

Charger/USB cable port cover problem

Charger/USB cable port cover gum is damaged and cover cannot be closed, what should i do?

You could try to either return your device to the place of purchase or contact Xperia care and have your device inspected http://www.sonymobile.com/global-en/support/contact-us/
or buy new flaps from amazon or ebay for example and replace them yourself
For a successful technology, reality must take precedence over public relations, for Nature cannot be fooled. Richard P. Feynman

Port disabled on switch

I have a switch with 2 ports disabled, saying err disabled, any ideas ?

Ports get err-disabled for various reason. Normally the switch would log a message saying why the port was err-disabled. If running CAT OS, do a "sh logging buffer -1023" and if running IOS do a "sh log" to check why the port err-disabled.
Depending on the reason, you can take action to remedy this in the future.

Are QOS BUM Policer BUM Parameters applicable for virtual ports or only for non virtual ports?

Are QOS BUM Policer BUM Parameters applicable for virtual ports or only for non virtual ports?

Just FYI.
I probably overestimated RHEL/OEL-5.3 capability to "compete in Music Showbiz" as a digital studio workstation OS. Seems that "very old" alsa kernel drivers (1.0.17), compiled with actual kernel, don't like Audigy cards when it comes to MIDI interface, despite the fact the audio is perfect. Although I am still not sure nothing could be done as a workaround in order to get MIDI worked on OEL-5.3, the fact is that SB Audigy MIDI works like Roland Synth, sounding amazingly, if the kernel 2.6.18-128.1.1.0.1.el5 is recompiled with the actual alsa driver version 1.0.19 (modules snd-emu10k1, snd-emu10k1-synth, etc).
It's interesting that overall device and loaded-modules schema's picture is the same as with old alsa (original kernel). That's why I still think something could be done, at least as workaround, to get MIDI worked with original OEL-5.3 kernel.
NJ

ISE 1.2 - Posture Detail Assessment - enforcement audit mode report not show status for non-compliant

ISE 1.2 - Posture Detail Assessment - enforcement audit mode report not show status for non-compliant.
- For old version 1.1.4 it can be reported for non-compliant, How can I generate report for this?
Thanks
Kosin Usuwanthim

It used to be in there (id 226635 is the last one with it); should I clean it up a bit and put it back with a bit more of a disclaimer?

How can I get report of only non compliant clients via Fileshare or to admin mailbox each day?

I need to figure out how to get a daily report of non compliant clients in SCCM2012 to admin email or fileshare.
Is there any built-in report that returns only non compliant clients I could use to accomplish this,
and create alert subscription or exchange server connector to receive the message / file once a day ?
Do I need to use SQL Server Reporting Services for this ? New to SCCM and getting confused with all those reports,
sorry ;-)

Yes you need SSRS for this.
This will help.
http://be.enhansoft.com/post/2013/08/27/How-to-Set-up-a-Windows-File-Share-Subscription.aspx
http://be.enhansoft.com/post/2013/08/14/How-to-Set-up-an-Email-Subscription-in-SSRS.aspx
Non compliant for what?
http://www.enhansoft.com/

PS CS5 workaround to non compliant Shader3.x/OpenGL 2.0 video cards

Stumbled upon a possible workaround for those who want to use some of the latest CS5 PhotoShop enhancements such as 3D effects and Repoussee which is worth sharing. Background.... home workstation is a i7-920 Windows 7 Ultimate 64-bit o/s with modest NVidia GTS250 which is fully hardware compliant Shader 3.x and OpenGL 2.0 however my company issued laptop used for traveling demo's is a standard Dell Latitude D620 with non compliant Intel GPU which was unable to create simple 3D effects with any invoked PhotoShop graphic. Each of the 3D effects from the PhotoShop CS5 pull downs were grayed out and verified as a non compliant via Edit --> Preferences -->Performance on the Dell D620. Finally had time to create a simple "down and dirty" 3D graphic using either the predefined hat or can 3D effect composed on the i7-920 Windows 7 Ultimate 64-bit o/s then saved as a file type PSD to a flash drive.
Open the same created file on my Dell D620, got a warning message the built in GPU on the Dell D620 was non compliant hardware hence rendering would be via software (versus video hardware). The 3D can opened on the Dell but more importantly I was able to successfully perform edits. Long story short you might be able to circumvent non compliant video card issues by opening a saved 3D PSD file which will render/edit on non-compliant GPU's. BTW, my D620 is 32-bit Windows XP Professional SP3. If others can try my premise and feed back to this forum it would prove beneficial to all the members in this forum. Can anyone validate this on say laptops other than a Dell D620 and Dell E6410? I suspect once you call in a 3D PSD file composed on a non-compliant platform, it toggles a PhotoShop "on" bit to enable 3D software rendering. Talk about being stoked on this exercise

Forgot to mention you still have to have CS5 installed on your non-compliant laptop. Wouldn't it be funny if this is a PS bug requiring a toggled bit to be set in order to render in 3D?

What is "Remediate non Compliant Rule when supported" and how to use it ?

Hi,
now i have created around 10 baselines for the driver compliance check for different make and model of laptops and desktops, the os platform on the computer will be Win 7 X 64 computers
CI's working fine and iam curious to learn what is the ( Remediate non Compliant Rule when supported ) option actually ment for , what all we can use it for ?
and i need a example with complete steps too please
all i can understand from the word Remediate is that it will either run a query or initiate a process such as install the correct version of driver etc , please correct me if iam wrong
Thank you
OSLM ENGINEER - SCCM 2007 & 2012

When creating a CI you can also configure a remediation script, that script will be used to remediate a non-compliant system. Also, some simple things like change the value of an existing registry key from 0 to 1 are supported out-of-the-box for compliance
and remediation.
An example:
http://www.petervanderwoude.nl/post/allow-direct-installation-of-windows-8-apps-via-compliance-settings-in-configmgr-2012/
Another example:
http://www.petervanderwoude.nl/post/go-to-desktop-on-sign-in-on-windows-8-1-via-compliance-settings-in-configmgr-2012/
My Blog: http://www.petervanderwoude.nl/
Follow me on twitter: pvanderwoude

NON-COMPLIANT: ..oraInst.loc doesn't point to inventory inside ORACLE_HOME

Hello Gurus:
I have just migrated and upgraded EBS 11i to 12.1.1 and now having trouble with the oraInventory setup.
I have the three $ORACLE_HOMEs for 11.2.0 rdbms, 10.1.2 & 10.1.3 for the apps.
cat /etc/oraInst.loc
inventory_loc=/etc/oraInventory
inst_group=oinstall
RDBMS:
cat /u01/app/oracle/product/11.2.0/db_1/oraInst.loc
inventory_loc=/etc/oraInventory
inst_group=oinstall
10.1.2 :
cat /u02/applfind/apps/tech_st/10.1.2/oraInst.loc
inventory_loc=/etc/oraInventory
inst_group=oinstall
10.1.3 :
cat /u02/applfind/apps/tech_st/10.1.3/oraInst.loc
inventory_loc=/etc/oraInventory
inst_group=oinstall
First there is no ouicli.pl in RDBMS home so I use ./runInstaller -silent -attachHome to add it to the inventory
For 10.1.2 & 10.1.3 Homes, when I use ouicli.pl it give me errors:
cd $ORACLE_HOME/appsutil/clone
./ouicli.pl
Out put:
NON-COMPLIANT: /u02/applfind/apps/tech_st/10.1.2/oraInst.loc does not point to an inventory inside the current ORACLE_HOME
Rapid Clone only supports oraInst.loc at that location if its content points to an inventory inside the same ORACLE_HOME
Please make the necessary changes to the following file:
/u02/applfind/apps/tech_st/10.1.2/oraInst.loc
running OUI CLI home cloning:
/u02/applfind/apps/tech_st/10.1.2/oui/bin/runInstaller -debug -clone -silent -force -nolink -waitForCompletion -invPtrLoc /etc/oraInst.loc session:ORACLE_HOME=/u02/applfind/apps/tech_st/10.1.2 oracle.as.j2ee.top:s_asInstanceName=OFD1_TOOLS__u02_applfind_apps_tech_st_10_1_2 oracle.as.j2ee.top:s_adminName=ias_admin oracle.as.j2ee.top:s_adminPassword=welcome ORACLE_HOME_NAME=OFD1_TOOLS__u02_applfind_apps_tech_st_10_1_2 -J-Doracle.installer.noLink=true
Finished OUI CLI cloning for s_tools_oh with return code: 0Sat Oct 6 04:52:49 2012
I have followed MOS Notes to no success:
How to create, update or rebuild the Central Inventory for Applications R12 [ID 742477.1]
How to Recreate the Global oraInventory [ID 295185.1]
Global and Local Inventory explained [ID 360079.1]
1) Looking at my oraInst.loc entries above what am I missing?
2) Should there be a local and then a Global inventory? And if so, how is each defined - especially the Local inventory?
3) How to I get ouicli.pl to update both local and global inventories as it is supposed to do?
4) Why is it that When I changed the entry of /u02/applfind/apps/tech_st/10.1.2/oraInst.loc to:
inventory_loc=/u02/applfind/apps/tech_st/10.1.2/oraInventory
The /etc/oraInventory/ContentsXML/inventory.xml will not be updated?
Thanks
ChoMA

Hello Hussein,
We are Migrating and upgrading EBS 11i on a 32 bit ULN 4 to EBS 12.1.3 on an x86-64 bit ULN following doc 557738.1 (Export/import notes ....)
We are currently at 12.1.1 and preparing to move onto 12.1.3.
The folder $ORACLE_HOME/appsutil/clone/bin on this new server and installation f 12.1.1 does not contain adcfgclone.pl as needed by Note 458653.1
Note [ID 742477.1] (How to create, update or rebuild the Central Inventory for Applications R12) called for using $ORACLE_HOME/appsutil/clone/ouicli.pl in the 11.2.0 rdbms ORACLE_HOME but this file (ouicli.pl) is also not there? It is nevertheless presnet in the in 10.1.2 & 10.1.3 ORACLE_HOMEs.
1) Looking at my three oraInst.loc entries above what am I missing?
2) Should there be two inventories (Local & Global)? And if so, how is each defined - especially the Local inventory?
3) How do I get ouicli.pl to update both local and global inventories as it is supposed to do? From the error (NON-COMPLIANT: /u02/applfind/apps/tech_st/10.1.2/oraInst.loc does not point to an inventory inside the current ORACLE_HOME), ouicli.pl apparenlty needs a local inventory but how do I define both?
4) Why is it that when I changed the entry of /u02/applfind/apps/tech_st/10.1.2/oraInst.loc to:
inventory_loc=/u02/applfind/apps/tech_st/10.1.2/oraInventory
The /etc/oraInventory/ContentsXML/inventory.xml will not be updated?
Thanks very much
ChoMA

3560 Interconnect Cable - Port Disabled b/c non-compliant GBIC

Similar Messages

Maybe you are looking for