3560 Map-class
Configuring a 3560. Fa0/1 is connected to LES cct, I need to apply a class-map to allocate bandwidth to Voip, Citrix and printing. I create class map and then try to apply the Service-policy output command but it comes back Output not supported. How do I apply the service policy to the port
will attaching the service-policy input to the port prioritse the traffic down the private cct. Also do I have to apply any qos rules to the other ports.
For example: Port fa0/1 is connected to 10mbps cct.
I attach service-policy to the port
'Service-policy output qos'
(full class-map is:
Class-map match-all class 1
match access-group 101
Class-map match-all class 2
match access-group 102
Class-map match-all class 3
match access-group 103
policy-map Qos
Class Class 1
police 100000 8000 exceed.... drop
Class Class 2
Police 512000 8000 exceed.... drop
Class Class 3
Police 6750000 8000 exceed ..... drop
Access-list 101 permit tcp any any dscp 46
Access-list 102 permit tcp any any dscp 31
Access-list 103 permit tcp any any eq 1494
I have configured (Global) mls qos
Do I have to configure fa0/3 which is configured for two vlans (voice and data)
Regards
Ron
Similar Messages
-
Acces dynamic configuration variable (e.g. filename) in ABAP mapping class
Hi experts
I am searching for a possibility to acces a dynamic configuration variable (DCV) in an ABAP mapping class. Since I could not find a solution in SDN and other sources, I hope somebody in this forum can help me.
What I already found is the following code which can be used to set a DCV, but what I would be interested in is how to read a DCV.
Any help is appreciated.
Markus
METHOD if_mapping~execute.
DATA l_record type mpp_dynamic.
* copy payload
result = source.
* add an adapter specific attribute
l_record-namespace = 'http://sap.com/xi/XI/System/File'.
l_record-name = 'FileName'.
l_record-value = 'test.xml'.
dynamic_configuration->add_record( l_record ).
ENDMETHOD.Hi Markus,
you can find everything in my blogs
/people/michal.krawczyk2/blog/2007/04/26/xipi-throwing-generic-exceptions-from-any-type-of-mapping
Regards,
michal -
XML to internal table conversion within ABAP mapping class
I am doing a ABAP mapping for file to Idoc. My requirement is to convert XML file into ABAP internal table (within ABAP mapping class). Is there any standard FM, method, transformation etc, which can be used here.
Thanks, DehraDehra,
Have you seen this weblogs which talks about this:
/people/r.eijpe/blog/2005/11/10/xml-dom-processing-in-abap-part-i--convert-an-abap-table-into-xml-file-using-sap-dom-approach
/people/r.eijpe/blog/2005/11/21/xml-dom-processing-in-abap-part-ii--convert-an-xml-file-into-an-abap-table-using-sap-dom-approach
/people/r.eijpe/blog/2006/02/19/xml-dom-processing-in-abap-part-iiia150-xml-dom-within-sap-xi-abap-mapping
/people/r.eijpe/blog/2006/02/20/xml-dom-processing-in-abap-part-iiib150-xml-dom-within-sap-xi-abap-mapping
Hope this helps you....
---Satish -
Use java mapping class on PI 7.0
Hi experts,
I have a problem with a java mapping class on PI 7.0, maybe somebody could help me.
I have a java mapping that call a webservice using AXIS library. If I run on my PC the java mapping is working. I load on Imported Archive the Java mapping class and AXIS librarys. My Java mapping class is compilated by jdk 1.4.2.09, like others java mappings that i have on PI 7.0 system, but when I execute the interface, its returns an error:
Incompatible class versions (linkage error)
This error is caused by AXIS Libraries, I use AXIS 1.4 version, and I think that this version is using jdk 1.5 because I read it on some foros. Could somebody confirm it? If it is true, could somebody tell me if there are some AXIS version that use jdk 1.4 or maybe How could I solved it? Thanks.
Regards,
GemmaIncompatible class versions (linkage error)
this is usually when the jdk version of XI server and the library version you used to develop the mapping are incompatible. Make sure you use the same version as of the server -
Hello Everyone.
Well I working on a program that uses Map class and I have some errors.
They are listed as.
on line 110
Type safety: The method put(Object, Object) belongs to the raw type HashMap. References to
generic type HashMap<K,V> should be parameterized
line 115
pe safety: The expression of type Collection needs unchecked conversion to conform to
Collection<ComputerInvent>
line 123
Type mismatch: cannot convert from Object to Computer_listing
Here is my code is far
import java.io.*;
import java.util.*;
class Computer_listing {
private String id;
private String name;
private Integer harddrive;
private Integer memory;
private float speed;
public Computer_listing(String idx) {
id = idx;
}// close the computer_listing loop
* Constructors.
public Computer_listing(String cd, String cn, Integer hd, Integer me,
float sp) {
id = cd;
name = cn;
harddrive = hd;
memory = me;
speed = sp;
}// close public EmployeeClass
* accessors make info available
public String getId() {
return id;
public String getName() {
return name;
public Integer getHardrive() {
return harddrive;
public Integer getMemory() {
return memory;
public float getSpeed() {
return speed;
* Mutator Methods
public void setId(String cd) {
id = cd;
public void setName(String cn) {
name = cn;
public void setHarddrive(Integer hd) {
harddrive = hd;
public void setMemory(Integer me) {
memory = me;
public void setSpeed(float sp) {
speed = sp;
}// close class
public class ComputerInvent {
public static void main(String[] args) {
HashMap hs = new HashMap();
Scanner kbd = new Scanner(System.in);
kbd.useDelimiter("\n");
while (true) {
String msg = null;
Computer_listing compdb = null;
System.out.println("Enter ComputerID - Stop to end");
msg = kbd.next();
if (msg.equalsIgnoreCase("STOP")) {
break;
} else {
compdb = new Computer_listing(msg);
System.out.println("Enter Computer Name");
compdb.setId(kbd.next());
System.out.println("Enter HardDrive");
compdb.setHarddrive(kbd.nextInt());
System.out.println("Enter Memory");
compdb.setMemory(kbd.nextInt());
System.out.println("Enter Speed");
compdb.setSpeed(kbd.nextFloat());
// add to data structure
hs.put(msg, hs); //line 110
}// close while loop
System.out.println("Done");
int i = 1;
Collection<ComputerInvent> values = hs.values();//line115
for (ComputerInvent temp : values) {
System.out.println("Items are " + i + "" + temp.getClass());
i++;
}// close for loop
System.out.println("Enter ID to find");
String findit = kbd.next();
Computer_listing x = null;
if ((x = hs.get(findit)) != null) { //line 123
System.out.println("Found it");
System.out.println("Name is " + x.getClass());
} else {
System.out.println("Did not find it");
}// close else
}// close public static void
}// close public class ComputerInventCan someone please help me in solving this.
thanks
sandyRThe code should have thrown hundreds of errors i wonder how u managed with few
import java.io.*;
import java.util.*;
class Computer_listing {
private String id;
private String name;
private Integer harddrive;
private Integer memory;
private float speed;
public Computer_listing(String idx) {
this.id = idx;
public Computer_listing(String cd, String cn, Integer hd, Integer me,
float sp) {
this.id = cd;
this.name = cn;
this.harddrive = hd;
this.memory = me;
this.speed = sp;
public String getId() {
return this.id;
public String getName() {
return this.name;
public Integer getHardrive() {
return this.harddrive;
public Integer getMemory() {
return this.memory;
public float getSpeed() {
return this.speed;
public void setId(String cd) {
this.id = cd;
public void setName(String cn) {
this.name = cn;
public void setHarddrive(Integer hd) {
this.harddrive = hd;
public void setMemory(Integer me) {
this.memory = me;
public void setSpeed(float sp) {
this.speed = sp;
public class ComputerInvent{
public static void main(String s[]){
HashMap<String,Computer_listing> hs = new HashMap<String,Computer_listing>();
Scanner kbd = new Scanner(System.in);
kbd.useDelimiter("\n");
while(true){
String msg = null;
Computer_listing compdb = null;
System.out.println("Enter <ComputerID> - Type <Stop> to end");
msg = kbd.next();
if (msg.equalsIgnoreCase("STOP"))
break;
else
compdb = new Computer_listing(msg);
System.out.println("Enter Computer Name:");
compdb.setId(kbd.next());
System.out.println("Enter HardDrive:");
compdb.setHarddrive(kbd.nextInt());
System.out.println("Enter Memory:");
compdb.setMemory(kbd.nextInt());
System.out.println("Enter Clock Speed:");
compdb.setSpeed(kbd.nextFloat());
hs.put(msg,compdb);
System.out.println("<Done>");
Collection<Computer_listing> values = hs.values();
int i = 0;
for (Computer_listing temp : values) {
System.out.println("Name["+ i + "]:" + temp.getName());
i++;
System.out.println("Enter ID to find");
String findit = kbd.next();
Computer_listing x = null;
if ((x = hs.get(findit)) != null) {
System.out.println("Found it");
System.out.println("Name is " + x.getName());
} else {
System.out.println("Did not find it");
}Hope that works :)
Anyways i'd advice you learn basics of using java.util Classes first and then go about using generics if you are a starter.
REGARDS,
RaHuL -
Query: Missing tablename in generated SQL for vertical mapped classes
Hi,
I am playing with Kodo 3.1.4 / Postgres 7.4 and could not find any
solution for this problem:
I have one class calles "Clipfragment" which represents video clips and
has a long - field named "lengthInMinutes". It extends a baseclass
called "Categorizablefragment", which has a field "id" and some others.
I use vertical mapping, thus having one table per class. The identity
type is 'application'. The table for the class "Categorizablefragment"
contains fields for jdoclass and jdoversion and IMHO correct entries.
Everything works really fine except for Querys against subclass fields
with aggregate functions. E.g. counting all clips works:
KodoQuery q = (KodoQuery) getJdoPm().newQuery(ClipFragment.class);
q.setResult ("count(id)");
Number count = (Number) q.execute ();
But: Querying for the sum of the field 'lengthInMinutes' fails:
KodoQuery q = (KodoQuery) getJdoPm().newQuery(ClipFragment.class);
q.setResult ("sum(lengthInMinutes)");
Number count = (Number) q.execute ();
The exception is:
kodo.util.UserException: com.solarmetric.jdbc.ReportingSQLException:
ERROR: syntax error at or near "WHERE"
{prepstmnt 16398807 SELECT AVG(t0.lengthinminutes) FROM WHERE
t1.jdoclass = ? [reused=0]} [code=0, state=42601]
NestedThrowables:
com.solarmetric.jdbc.ReportingSQLException: ERROR: syntax error at or
near "WHERE"
{prepstmnt 16398807 SELECT AVG(t0.lengthinminutes) FROM WHERE
t1.jdoclass = ? [reused=0]} [code=0, state=42601]
at kodo.query.AbstractQuery.executeWithMap(AbstractQuery.java:865)
at kodo.query.AbstractQuery.execute(AbstractQuery.java:728)
atde.jk.buvas.model.impl.DefaultClipManager.getTotalTime(DefaultClipManager.java:43)
And the SQL - Trace:
5766 TRACE [main] kodo.jdbc.SQL - <t 17089909, conn 31908613 (1
errors)> [0 ms] executing prepstmnt 17226426 SELECT
SUM(t0.lengthinminutes) FROM WHERE t1.jdoclass = ? [params=(String)
de.jk.buvas.model.fragments.ClipFragment] [reused=0]
I tried both 'base-tables' and 'per-subclass' for the property
kodo.jdbc.VerticalQueryMode, without any results.
Any ideas?
Thanks,
JochenHi Stephen,
here are the excerpts from the .jdo and the .mapping files. The .jdo
file was generated by XDoclet.
..jdo
<class name="ClipFragment"
identity-type="application"
objectid-class="CategorizableFragment$Id"
persistence-capable-superclass="CategorizableFragment"
> <!-- end class tag -->
<extension vendor-name="kodo"
key="jdbc-class-map-name"
value="vertical">
<extension vendor-name="kodo" key="table" value="Clip"/>
</extension>
<field name="title"
> <!-- end field tag -->
<extension vendor-name="kodo"
key="jdbc-size"
value="100">
</extension>
</field>
<field name="lengthInMinutes"
> <!-- end field tag -->
</field>
<field name="description"
> <!-- end field tag -->
<extension vendor-name="kodo"
key="jdbc-size"
value="3000">
</extension>
</field>
<field name="recordingDate"
> <!-- end field tag -->
</field>
<field name="actors"
> <!-- end field tag -->
<collection
element-type="de.jk.buvas.model.fragments.ActorFragment"
> <!-- end collection tag -->
</collection>
<extension vendor-name="kodo"
key="jdbc-element-delete-action"
value="exception-deferred">
</extension>
<extension vendor-name="kodo"
key="inverse-owner"
value="clips">
</extension>
</field>
<field name="media"
> <!-- end field tag -->
<collection
element-type="de.jk.buvas.model.fragments.MediumFragment"
> <!-- end collection tag -->
</collection>
<extension vendor-name="kodo"
key="jdbc-element-delete-action"
value="exception-deferred">
</extension>
</field>
</class>
<class name="CategorizableFragment"
identity-type="application"
objectid-class="CategorizableFragment$Id"
> <!-- end class tag -->
<extension vendor-name="kodo"
key="jdbc-class-map-name"
value="base">
<extension vendor-name="kodo" key="table" value="Categorizable"/>
</extension>
<field name="id"
primary-key="true"
> <!-- end field tag -->
</field>
<field name="category"
> <!-- end field tag -->
<extension vendor-name="kodo"
key="jdbc-delete-action"
value="exception-deferred">
</extension>
</field>
</class>
..mapping
<class name="ClipFragment">
<jdbc-class-map type="vertical" ref-column.ID="ID" table="CLIPFRAGMENT"/>
<field name="actors">
<jdbc-field-map type="many-many" element-column.ID="ID"
ref-column.ID="CLIPS_ID" table="ACTOR_CLIPS"/>
</field>
<field name="description">
<jdbc-field-map type="value" column="DESCRIPTION"/>
</field>
<field name="lengthInMinutes">
<jdbc-field-map type="value" column="LENGTHINMINUTES"/>
</field>
<field name="media">
<jdbc-field-map type="many-many" element-column.ID="MEDIA_ID"
order-column="MEDIA_ORDER" ref-column.ID="ID" table="CLIPF_MEDIA"/>
</field>
<field name="recordingDate">
<jdbc-field-map type="value" column="RECORDINGDATE"/>
</field>
<field name="title">
<jdbc-field-map type="value" column="TITLE"/>
</field>
</class>
<class name="CategorizableFragment">
<jdbc-class-map type="base" table="CATEGORIZABLEFRAGMENT"/>
<jdbc-version-ind type="version-number" column="JDOVERSION"/>
<jdbc-class-ind type="in-class-name" column="JDOCLASS"/>
<field name="category">
<jdbc-field-map type="one-one" column.ID="CATEGORY_ID"/>
</field>
<field name="id">
<jdbc-field-map type="value" column="ID"/>
</field>
</class>
Thanks,
Jochen
Stephen Kim wrote:
Can you post the mapping/metadata files for the two classes?
Jochen Kressin wrote:
Hi,
I am playing with Kodo 3.1.4 / Postgres 7.4 and could not find any
solution for this problem:
I have one class calles "Clipfragment" which represents video clips
and has a long - field named "lengthInMinutes". It extends a baseclass
called "Categorizablefragment", which has a field "id" and some
others. I use vertical mapping, thus having one table per class. The
identity type is 'application'. The table for the class
"Categorizablefragment" contains fields for jdoclass and jdoversion
and IMHO correct entries.
Everything works really fine except for Querys against subclass fields
with aggregate functions. E.g. counting all clips works:
KodoQuery q = (KodoQuery) getJdoPm().newQuery(ClipFragment.class);
q.setResult ("count(id)");
Number count = (Number) q.execute ();
But: Querying for the sum of the field 'lengthInMinutes' fails:
KodoQuery q = (KodoQuery) getJdoPm().newQuery(ClipFragment.class);
q.setResult ("sum(lengthInMinutes)");
Number count = (Number) q.execute ();
The exception is:
kodo.util.UserException: com.solarmetric.jdbc.ReportingSQLException:
ERROR: syntax error at or near "WHERE"
{prepstmnt 16398807 SELECT AVG(t0.lengthinminutes) FROM WHERE
t1.jdoclass = ? [reused=0]} [code=0, state=42601]
NestedThrowables:
com.solarmetric.jdbc.ReportingSQLException: ERROR: syntax error at or
near "WHERE"
{prepstmnt 16398807 SELECT AVG(t0.lengthinminutes) FROM WHERE
t1.jdoclass = ? [reused=0]} [code=0, state=42601]
at kodo.query.AbstractQuery.executeWithMap(AbstractQuery.java:865)
at kodo.query.AbstractQuery.execute(AbstractQuery.java:728)
atde.jk.buvas.model.impl.DefaultClipManager.getTotalTime(DefaultClipManager.java:43)
And the SQL - Trace:
5766 TRACE [main] kodo.jdbc.SQL - <t 17089909, conn 31908613 (1
errors)> [0 ms] executing prepstmnt 17226426 SELECT
SUM(t0.lengthinminutes) FROM WHERE t1.jdoclass = ? [params=(String)
de.jk.buvas.model.fragments.ClipFragment] [reused=0]
I tried both 'base-tables' and 'per-subclass' for the property
kodo.jdbc.VerticalQueryMode, without any results.
Any ideas?
Thanks,
Jochen -
Map-class frame-relay , policy map
Does a service-policy output have to be applied to an interface for qos to work?
here is the config but there is nothing applied to the serial interface..
Thanks for your help
policy-map 256/128KVoice
class 256/128KVoice
priority 112
class class-default
fair-queue
map-class frame-relay 256/128KVoice
frame-relay cir 128000
frame-relay bc 1280
frame-relay be 600
frame-relay mincir 128000
no frame-relay adaptive-shaping
frame-relay fair-queue
frame-relay fragment 150
frame-relay ip rtp priority 16384 16380 210
interface Serial0/0
bandwidth 1544
ip address xxx.xxx.xxx.xxx 255.255.255.255
ip route-cache flow
no fair-queue
service-module t1 timeslots 1-24Hello,
Will QOS will work in this way where class is put on WAN interface where it should be service policy.
router#sh run interface Se0/0/0.1
Building configuration...
Current configuration : 239 bytes
interface Serial0/0/0.1 point-to-point
bandwidth 2048
ip address XXXX
ip nat outside
frame-relay interface-dlci 555
class COS-OUT-S0/0/0.1
end
COS-OUT-S0/0/0.1 is defined as policy map with class of voice and video.
When checking on WAN int #sh policy-map interface Se0/0/0.1 , can see output of service policy input/output with policy map recpective classes and packets match entries.Is QOS working with this configuration?
Appreciate any input on this.
Regards,
Brajesh. -
Total drops for class-map class-default
Hi,
I have a gigabit ethernet interface on a 2951 configured with 4x sub interfaces providing connectivity to our four WAN sites. Each sub interface services a 100mb connection to another site.
I have configured a QoS policy and attached to each sub interface with the primary function of limiting each sub interface to 100mbs. I am now seeing drops (total drops) on the class default and not sure why. I would not expect to see any drops on this interface as it never even reaches 15mb (15%) capacity.
Any ideas?
Class-map: class-default (match-any)
175934881 packets, 95319007968 bytes
5 minute offered rate 23000 bps, drop rate 0000 bps
Match: any
queue limit 64 packets
(queue depth/total drops/no-buffer drops) 0/340/0
(pkts output/bytes output) 314212026/180287074028
policy-map PM-Branch-QoS
class CM-OAM
set dscp af11
class CM-Network
set dscp cs6
class CM-VC
bandwidth percent 5
class CM-Citrix
set dscp af21
class CM-CAPWAP
set dscp af22
policy-map PM-WAN
class class-default
shape peak 100000000
service-policy PM-Branch-QoSDisclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
I would not expect to see any drops on this interface as it never even reaches 15mb (15%) capacity.
Your expectations might be incorrect. Often percentage of bandwidth capacity measurements are misunderstood.
Let's assume your ingress is 100 Mbps. Let's also assume your measuring over a five minute period. Lastly, assume the ingress transmits at 100% for 1 minute and then stops for 4 minutes. Bandwidth utilization across the 1 minute would be 100% and 0% for the other 4 minutes, but it would be 20% for the 5 minutes.
But if the 100 Mbps was sent at 100% for each 12 seconds, and not sent for each 48 seconds, 5 minute utilization would still be 20% but unlike the prior 1 minute stats of 100% and 0%, each minute would now also be 20%.
So these first two examples show how bandwidth utilization don't reveal what's happening within the measured time period.
Since ingress was same bandwidth as egress, in the above, there would be no queuing.
If ingress is gig, though, suppose gig ingress arrives for 6 seconds and stops for a remaining 4 minutes and 54 seconds. This too would measure as 20% usage across 5 minutes, but since it will take 60 seconds to transmit the same traffic at 100 Mbps, packets will need to be queued. If queuing buffers are insufficient to hold all the packets, some will be dropped.
The above is a long way of saying, if your ingress rate exceeds your egress rate, there can be a need to queue packets, and if queuing is insufficient, packets will be dropped, this even if utilization is "low". Most likely, you have occasional "bursts" if ingress bandwidth exceeds the egress bandwidth.
From your actual stats, the drop rate percentage is so low, you might not need to concern yourself with the few drops you're seeing. If it is a concern, you might be able to reduce the drop rate by increasing egress buffering, but doing so, also increases egress queuing delay. -
QoS for Framerelay with map-classes or with shapers
Hi,
For a customer we have a E1 leasedline for transport between CE en PE. Now to tranport 3 seperate connections we want to use FrameRelay. On top of that we want QoS. Now normally we use on ethernet Shapers but some say we have to use Map-classes on framerelay instead.
Is that true and whyWe can user but for for that we neede to enable frame-relay traffic shapping first.
After that you can create frame-relay map and match the traffic
shivlu -
Performance in XI / PI ABAP mapping class
Hi,
I have to do some ABAP mapping for XI / PI scenarios. First of all number of messages is huge, messages can be very large,
so my question is where to pay special attention because of performance. Is there some blog on net with suggestions? I saw and read lot of ABAP mapping blogs, but I have never found one where is it performance explained.
br
marioHi there.
The performace problem of the ABAP Mappings in XI/PI is not related to the code itself. When coding, just keep in mind alll you have said: "messages are huge, and lot's of messages". This way, you should keep the code as sharp as possible within the class methods you will use.
Now, the real problem in ABAP mapping is ther ABAP mapping itself. Don't forget that PI usually (and ideally) processes the message mappins (or java mappings) in the java stack. If you are creating an ABAP mapping, you are telling PI to send the work to the integration server (ABAP stack), and then retrive the result from it.
If you can, use message mapping or java mapping for best performance. If you cannot, use ABAP mapping but having all this in mind. Hope this helped.
Regards,
Valter Oliveira. -
How to use "put" function in Java.util.Map class
intially an entry for key is null in a Map.
then if I try to do put function on the map with the same key which had a null value previously It doesn't allow me to put the new value for the Key.
Can anyone pleasee suggest as to how I can put a value on to key with the new value even if the old value is null.
Waiting for repliesI have problem with the "value"..Not with a "key"
parameter in the function.I already have a value for
Key...that is "Firstkey"
Map map = new HashMap();
String column = "FirstKey";
map.put(column, null);
The below step gives me an IllegalArgumentException
map.put(column, "FirstValue");That's not the problem. Your error is somewhere else.
This works.
public class Test {
public static void main(String[] args) {
Map map = new HashMap();
String column = "FirstKey";
map.put(column, null);
map.put(column, "FirstValue");
System.out.println("Done");
}Kaj -
Is it possible to call XSLT from Java Mapping Class?
Hi,
does someone have experience with this? Or any ideas?
And, if yes, how can be this XSLT called? Is it necessary to specify special path? Or it is the XSLT file placed in the same directory?
Thanx in advance, Peter
Message was edited by: Peter JarsunekHi SUdhir,
Thanx 4 your answer. I have seen this link before, but there is only Java->Java or XSLT->Java calling.. I need Java->XSLT.. When I create Java mapping, I want to use stored XSLT stylesheet to convert the message. Because, my problem is,that my primary message contains characters which I want to be changed. For this reason I need java class - to replace the characters. And then I want to do transformation with the XSLT stylesheet. Can you post some example?
Thanx, Peter -
Hi there,
I am not entirely sure, if this is the right section of this forum. If not, can any moderator please put it into the right section? Thank you.
So here's the problem:
Let's assume, we have a class Car which associates loads of Part classes. Example:
public class Car {
private List<Part> parts;
}The classes are Entities, and we are using Hibernate and JPA annotations to persist them.
Using Java-WS with Netbeans, that would result in a (simplified) XML structure like this:
<car>
<parts>
<part>
</part>
</parts>
</car>What I want to do now is to map the parts directly into the car node (skipping the <parts> node altogether), like this:
<car>
<part>
</part>
<part>
</part>
</car>I am aware that this is NOT good style. However, I have to stick to the non-standard requirements of the clients who use the SOAP interface later. Also I must not change the underlying database structure.
Is there a way to solve this with existing Annotations?
Thanks in advance!JAXB will create classes from an XML schema, SAX is a parser library and JAXP is a library of XML a bunch of XML tools.
I don't care for JAXB too much. I would skip it and go right to the JAX-RPC spec (WebServices). -
Policy map/ class map/ service policy for IOS xr
Hi,
I need to create a policy map and class map/service policy to limit the amount of bandwidth that can be used on one interface both in and out.
I need the cap for the bandwidth to traverse this circuit to ne 10 Meg.
the IOS xr version we are using is 4.3.4
I was hoping someone could help me out by giving me a configuration example I could follow.
Thank you.for instance like this:
policy-map police-in
class class-default
police rate 10 mpbs <optionally set burst>
policy-map shape-out-parent
class class-default
shape 10 mpbs <optional burst config>
service-policy shape-out-child
policy-map shape-out-child
class class-default
queue-limit 10 packets
int g 0/0/0/0
service-policy police-in in
service-policy shape-out-parent out
also have a look at CL 2013/2014 (orlando/sanfran) ID 2904 for more QOS details
and the support forum article of "asr9000 quality of service architecture"
xander -
Java Mapping - Class versions are incompatible (linkage error)
Hi Friends,
While testing java mapping in Integration Repository i am getting an error - "Class versions are incompatible (linkage error)". Can anyone plz tell what might be the reason.
Regards,
Gowtham Kuchipudi.hello
I have this message but my trace look like this:
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- <!-- Request Message Mapping
-->
- <SAP:Trace xmlns:SAP="http://sap.com/xi/XI/Message/30">
- <Trace level="1" type="B" name="interface activity determination">
<Trace level="1" type="T">Version 000</Trace>
<Trace level="1" type="T">Message status 000</Trace>
<Trace level="1" type="T">Interface action INIT</Trace>
<Trace level="1" type="T">(must be INIT for a new determination)</Trace>
<Trace level="1" type="T">Message type BEST EFFORT. -> No determination</Trace>
<Trace level="1" type="T">Set interface action INIT into *MAST*</Trace>
</Trace>
<Trace level="1" type="E">CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST</Trace>
- <Trace level="1" type="B" name="PLSRV_RECEIVER_DETERMINATION">
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL">
- <Trace level="1" type="B" name="CL_RD_PLSRV-ENTER_PLSRV">
<Trace level="1" type="T">R E C E I V E R - D E T E R M I N A T I O N</Trace>
<Trace level="1" type="T">Cache Content is up to date</Trace>
</Trace>
</Trace>
</Trace>
</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST" />
- <Trace level="1" type="B" name="PLSRV_INTERFACE_DETERMINATION">
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL">
- <Trace level="1" type="B" name="CL_ID_PLSRV-ENTER_PLSRV">
<Trace level="1" type="T">I N T E R F A C E - D E T E R M I N A T I O N</Trace>
<Trace level="1" type="T">Cache Content is up to date</Trace>
</Trace>
</Trace>
</Trace>
</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST" />
- <Trace level="1" type="B" name="PLSRV_RECEIVER_MESSAGE_SPLIT">
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL">
- <Trace level="1" type="B" name="CL_XMS_PLSRV_RECEIVER_SPLIT-ENTER_PLSRV">
<Trace level="1" type="T">number of receivers: 1</Trace>
<Trace level="1" type="T">Single-receiver split case</Trace>
</Trace>
</Trace>
</Trace>
</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST" />
<Trace level="1" type="B" name="PLSRV_MAPPING_REQUEST" />
- <!-- ************************************
-->
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL" />
- <!-- ************************************
-->
<Trace level="1" type="B" name="CL_MAPPING_XMS_PLSRV3-ENTER_PLSRV" />
- <!-- ************************************
-->
<Trace level="1" type="T">Interface Mapping http://Migdal.co.il/CRM/SAP-CRM/ProposalDeatailsService ProposalDeatailsService_WS2RFC_IM</Trace>
<Trace level="1" type="T">LinkageError at JavaMapping.load(): Could not load class: xmlpayload</Trace>
<Trace level="1" type="T">java.lang.UnsupportedClassVersionError: xmlpayload (Unsupported major.minor version 49.0) at java.lang.ClassLoader.defineClass0(Native Method) at java.lang.ClassLoader.defineClass(ClassLoader.java:539) at java.lang.ClassLoader.defineClass(ClassLoader.java:448) at com.sap.aii.ibrun.server.mapping.MappingLoader.findClass(MappingLoader.java:158) at java.lang.ClassLoader.loadClass(ClassLoader.java:289) at java.lang.ClassLoader.loadClass(ClassLoader.java:235) at com.sap.aii.ibrun.server.mapping.JavaMapping.load(JavaMapping.java:95) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:45) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:90) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:95) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:68) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:79) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0_0.processFunction(MappingServiceObjectImpl0_0.java:131) at sun.reflect.GeneratedMethodAccessor296.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy158.processFunction(Unknown Source) at sun.reflect.GeneratedMethodAccessor428.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:107) at com.sap.engine.services.rfcengine.RFCJCOServer.handleRequestInternal(RFCJCOServer.java:113) at com.sap.engine.services.rfcengine.RFCJCOServer$ApplicationRunnable.run(RFCJCOServer.java:157) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:102) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:172)</Trace>
<Trace level="1" type="T">Linkage error occurred when loading class xmlpayload (http://Migdal.co.il/CRM/SAP-CRM/ProposalDeatailsService, d7e31f30-53be-11dc-8fbd-ee09c0a8664d, -1)</Trace>
<Trace level="1" type="T">com.sap.aii.ibrun.server.mapping.MappingRuntimeException: Linkage error occurred when loading class xmlpayload (http://Migdal.co.il/CRM/SAP-CRM/ProposalDeatailsService, d7e31f30-53be-11dc-8fbd-ee09c0a8664d, -1) at com.sap.aii.ibrun.server.mapping.JavaMapping.load(JavaMapping.java:115) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:45) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:90) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:95) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:68) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:79) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0_0.processFunction(MappingServiceObjectImpl0_0.java:131) at sun.reflect.GeneratedMethodAccessor296.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy158.processFunction(Unknown Source) at sun.reflect.GeneratedMethodAccessor428.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:107) at com.sap.engine.services.rfcengine.RFCJCOServer.handleRequestInternal(RFCJCOServer.java:113) at com.sap.engine.services.rfcengine.RFCJCOServer$ApplicationRunnable.run(RFCJCOServer.java:157) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:102) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:172) Root Cause: java.lang.UnsupportedClassVersionError: xmlpayload (Unsupported major.minor version 49.0) at java.lang.ClassLoader.defineClass0(Native Method) at java.lang.ClassLoader.defineClass(ClassLoader.java:539) at java.lang.ClassLoader.defineClass(ClassLoader.java:448) at com.sap.aii.ibrun.server.mapping.MappingLoader.findClass(MappingLoader.java:158) at java.lang.ClassLoader.loadClass(ClassLoader.java:289) at java.lang.ClassLoader.loadClass(ClassLoader.java:235) at com.sap.aii.ibrun.server.mapping.JavaMapping.load(JavaMapping.java:95) at com.sap.aii.ibrun.server.mapping.JavaMapping.executeStep(JavaMapping.java:45) at com.sap.aii.ibrun.server.mapping.Mapping.execute(Mapping.java:92) at com.sap.aii.ibrun.server.mapping.MappingHandler.run(MappingHandler.java:90) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleMappingRequest(MappingRequestHandler.java:95) at com.sap.aii.ibrun.sbeans.mapping.MappingRequestHandler.handleRequest(MappingRequestHandler.java:68) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceImpl.processFunction(MappingServiceImpl.java:79) at com.sap.aii.ibrun.sbeans.mapping.MappingServiceObjectImpl0_0.processFunction(MappingServiceObjectImpl0_0.java:131) at sun.reflect.GeneratedMethodAccessor296.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.ejb.session.stateless_sp5.ObjectStubProxyImpl.invoke(ObjectStubProxyImpl.java:187) at $Proxy158.processFunction(Unknown Source) at sun.reflect.GeneratedMethodAccessor428.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest(RFCDefaultRequestHandler.java:107) at com.sap.engine.services.rfcengine.RFCJCOServer.handleRequestInternal(RFCJCOServer.java:113) at com.sap.engine.services.rfcengine.RFCJCOServer$ApplicationRunnable.run(RFCJCOServer.java:157) at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37) at java.security.AccessController.doPrivileged(Native Method) at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:102) at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:172)</Trace>
<Trace level="1" type="E">CL_XMS_PLSRV_MAPPING~ENTER_PLSRV</Trace>
</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST" />
- <!-- ************************************
-->
</SAP:Trace>
the error that I recieve in the SXMB is:
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- <!-- Request Message Mapping
-->
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
<SAP:Category>Application</SAP:Category>
<SAP:Code area="MAPPING">LINKAGE_ERROR</SAP:Code>
<SAP:P1>xmlpayload</SAP:P1>
<SAP:P2>http://Migdal.co.il/CRM/SAP-CRM/ProposalDeatailsS~</SAP:P2>
<SAP:P3>d7e31f30-53be-11dc-8fbd-ee09c0a8664d</SAP:P3>
<SAP:P4>-1</SAP:P4>
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Class versions are incompatible (linkage error)</SAP:Stack>
<SAP:Retry>N</SAP:Retry>
</SAP:Error>
this is my XI information
Runtime Environment
Java version:1.4.2_12
Java vendor:Sun Microsystems Inc.
Version
Service pack:21
Release:30_VAL_REL
Latest change:409678
Sync time:200709211024
since I already have the SP required by the note, any other suggestions?
Thanks
Kfir
Maybe you are looking for
-
Logical system with business service
hi, can we have a logical system with business service just like we have with business system?? If yes,how can we create logical system for business service?? Ratna.
-
Where is a twain-compliant device so my cm1312nfi mfp will scan? (windows7 pro op system)
where is a twain-compliant device so my cm1312nfi mfp will scan? (windows7 pro op system)
-
Hi Gurus, please help me or suggest me how to handle the below mentioned requirment. We have a requirement from one of client's customers to do a u201CBill and Holdu201D orders. In other words they want to pay for the product when it is produced. T
-
Please help to set the time zone in a porper way
Dear Folks please help to set the time zone in a porper way select sessiontimezone from dual; Database: Oracle 11.2.0.2 Operating system: AIX 5.3 SESSIONTIMEZONE +00:00 SQL> select systimestamp from dual; SYSTIMESTAMP 06-NOV-12 04.21.07.438426 AM +00
-
File or assembly name Oracle.DataAccess, or one of its dependencies not fnd
I need to install my old batch programs (using VB.NET 2003) onto a new server. I had the DBA install Oracle Client and ODP.NET on this machine. I installed the batch job onto this new server and when I try and test the program, I get the above error: