3600 AP %CDP_PD-2-POWER_LOW: All radios disabled

Hi All,
I am facing issue with some 3600 APs. These aps are not joining WLC. We have total 137 APs. out of which 97 are registered but rest of them are not getting registered and I am keep getting message on AP console %CDP_PD-2-POWER_LOW: All radios disabled.
While troubleshooting I noticed that Controller can ping these IPs but with drops. So I thought it is a cable issue but when I connect AP directly to switch ports still I get ping drop from controllers IP. When I look at switch port power it shows 13.0 for all non registered APs where as working one is showing 15.4. I have checked there is no network issue. WLC can ping other APs very well being in same subnet only APs which are not getting registered are not pingable 100% there are drops while pinging APs.
All APs are in same subnet and WLC MGMT interface is in different subnet. AP joins WLC via option 43.
I am attaching logs from AP console. I am runing 7.5.102
Can any body help me on this.

New-ASW01# sh power in
Available:847.0(w) Used:139.4(w) Remaining:707.6(w)
Interface Admin Oper       Power   Device              Class Max
                            (Watts)
Gi0/1     auto   on         16.8    AIR-CAP3602I-E-K9   4     30.0
Gi0/2     auto   on         15.4    AIR-CAP3602I-E-K9   4     30.0
Gi0/3     auto   on         13.0    AIR-CAP3602I-E-K9   4     30.0
Gi0/4     auto   on         16.8    AIR-CAP3602I-E-K9   4     30.0
Gi0/5     auto   on         13.0    AIR-CAP3602I-E-K9   4     30.0
Gi0/6     auto   off        0.0     n/a                 n/a   30.0
Gi0/7     auto   on         16.8    AIR-CAP3602I-E-K9   4     30.0
Gi0/8     auto   on         15.4    AIR-CAP3602I-E-K9   4     30.0
Gi0/9     auto   on         16.8    AIR-CAP3602I-E-K9   4     30.0
Gi0/10    auto   on         15.4    Ieee PD             4     30.0
Gi0/11    auto   off        0.0     n/a                 n/a   30.0
================================================
Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 09-Feb-12 18:32 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
ROM: Bootstrap program is C3560E boot loader
BOOTLDR: C3560E Boot Loader (C3560X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
IDF1 uptime is 5 hours, 42 minutes
System returned to ROM by power-on
System image file is "flash:/c3560e-universalk9-mz.122-55.SE5/c3560e-universalk9-mz.122-55.SE5.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: lanbase
License Type: Permanent
Next reload license Level: lanbase
cisco WS-C3560X-48P (PowerPC405) processor (revision K0) with 262144K bytes of memory.
Processor board ID FDO1716H0SJ
Last reset from power-on
2 Virtual Ethernet interfaces
1 FastEthernet interface
52 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : 6C:41:6A:30:82:00
Motherboard assembly number     : 73-12557-08
Motherboard serial number       : FDO17160A8F
Model revision number           : K0
Motherboard revision number     : A0
Model number                    : WS-C3560X-48PF-L
Daughterboard assembly number   : 800-32786-02
Daughterboard serial number     : FDO17150GP4
System serial number            : FDO1716H0SJ
Top Assembly Part Number        : 800-31328-07
Top Assembly Revision Number    : B0
Version ID                      : V04
CLEI Code Number                : COMJP00ARD
Hardware Board Revision Number : 0x04
Switch Ports Model              SW Version            SW Image
*    1 54    WS-C3560X-48P      12.2(55)SE5           C3560E-UNIVERSALK9-M
Configuration register is 0xF

Similar Messages

All Radio Disabled for AP1252AG

Hi,
I have 4500-E serial Catalyst Switch and AP1252AG access point.
WS-X4248-RJ45V (48 Port PoE Card) is installed in 4500-E switch and access point is connected with this switch without power injector. But i am getting LOW power error in AP. AP have 3 radios (2.4 GHz). I have tested with 1 radio also but still i have same problem.
Can you please guide me to solve this problem ?
What power command i have to apply on switch port and AP interface.
Its very urgent please...

Hi Prashant,
From Steve @ Cisco;
Information on the 4500 supporting the 1252 is below:
4500 modules req switch to run 12.2(44)SG or later
WS-X4648-RJ45V-E
WS-X4648-RJ45V+E
power inline port maximum 20000
power inline auto max
From this excellent thread;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&topicID=.ee6e8b8&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc1c2b6
Hope this helps!
Rob

How to uncheck all radio buttons in WHEN-NEW-FORM-INSTANCE trigger

Hi,
I have one radio group(RDBTNGRP) having three radio buttons (RDBTN1,RDBTN2,RDBTN3) in a control block, i want to uncheck all these three buttons through code.
Any help please.
Regards,

Hello,
I don't think you can achieve using the code or property to unselect all radio buttons.
One possibility is there to create one extra radio button in that same group and set any value for that. Let say you have two radio buttons in the radio group and now you created one more radio button in the same group. And set the value like ABC. Now go to the property of new created radio button and set the X Position, Y Position, Width and Height to zero (0). And set the initial value for that radio group to ABC (new created radio button). So at runtime it will look like unselected all radio buttons. And while saving you can check if radio button selected on your criteria or not.
-Ammad

Failed to load WMSchApi.dll. Error 1114 All Operation disabled

We currently have a large number or workstations that have imported fine, we
can view diag info but are unable to use any remote control functionality.
Below is an extract from the zen remote log file which shows a failed load
off wmschapi.dll and a critical error .
Anybody got a fix that can be automated
Thanks
Scott
We're using the ZFD agent from IR4 patch which is working fine on other PCs,
all 49 SP2 clients, W2K SP4.
#(660)# 16:59:50 11/24/04 Normal : Loading : C:\Program
Files\Novell\ZENworks\ZenLite.dll
#(660)# 16:59:50 11/24/04 Normal : Loading : C:\Program
Files\Novell\ZENworks\ZenPol32.dll
#(660)# 16:59:50 11/24/04 Normal : ZENNDSUtil: Successfully loaded
dependent modules...
#(660)# 16:59:50 11/24/04 Normal : LoadZenAutilLibraryAndGetProc:
Successfully loaded ZenAutil.dll and its dependent DLLs
#(660)# 16:59:50 11/24/04 Normal : Console version is SP1
#(660)# 16:59:50 11/24/04 Critical : ZenRmServer: Failed to find
Console Version #0.6.5.1 in supportability list
#(660)# 16:59:50 11/24/04 Warning :
RMAudit::Auditing.cpp:RMSesstionStart() The audit log file is not found.
#(660)# 16:59:50 11/24/04 Normal : ZENUtil:
ZENIsWorkstationRegistered: wsDN 'CN#(660)# 16:59:50 11/24/04 Normal :
Workstation is registered
#(660)# 16:59:50 11/24/04 Normal : ZENNDSUtil: Attempting to read
policies...
#(660)# 16:59:50 11/24/04 Normal : ZENUtil:
ZENIsWorkstationRegistered: wsDN 'CN#(660)# 16:59:50 11/24/04 Normal :
Workstation is registered
#(660)# 16:59:50 11/24/04 Normal : Reading workstation DN and tree
name...
#(660)# 16:59:50 11/24/04 Normal : workstation DN -
CN
#(660)# 16:59:50 11/24/04 Normal : Loading : C:\Program
Files\Novell\ZENworks\WMSchApi.dll
#(660)# 16:59:50 11/24/04 Critical : ZENNDSUtil: Failed to load
WMSchApi.dll. Error: 1114
#(660)# 16:59:50 11/24/04 Normal : Reading workstation DN and tree
name...
#(660)# 16:59:50 11/24/04 Normal : workstation DN -
CN
#(660)# 16:59:50 11/24/04 Normal : Loading : C:\Program
Files\Novell\ZENworks\WMSchApi.dll
#(660)# 16:59:50 11/24/04 Critical : ZENNDSUtil: Failed to load
WMSchApi.dll. Error: 1114
#(660)# 16:59:50 11/24/04 Normal : Neither policy settings active.
All operations disabled.

> We currently have a large number or workstations that have imported fine, we
> can view diag info but are unable to use any remote control functionality.
>
> Below is an extract from the zen remote log file which shows a failed load
> off wmschapi.dll and a critical error .
>
> Anybody got a fix that can be automated
>
> Thanks
>
> Scott
>
> We're using the ZFD agent from IR4 patch which is working fine on other PCs,
> all 49 SP2 clients, W2K SP4.
>
>
> #(660)# 16:59:50 11/24/04 Normal : Loading : C:\Program
> Files\Novell\ZENworks\ZenLite.dll
> #(660)# 16:59:50 11/24/04 Normal : Loading : C:\Program
> Files\Novell\ZENworks\ZenPol32.dll
> #(660)# 16:59:50 11/24/04 Normal : ZENNDSUtil: Successfully loaded
> dependent modules...
> #(660)# 16:59:50 11/24/04 Normal : LoadZenAutilLibraryAndGetProc:
> Successfully loaded ZenAutil.dll and its dependent DLLs
> #(660)# 16:59:50 11/24/04 Normal : Console version is SP1
> #(660)# 16:59:50 11/24/04 Critical : ZenRmServer: Failed to find
> Console Version #0.6.5.1 in supportability list
> #(660)# 16:59:50 11/24/04 Warning :
> RMAudit::Auditing.cpp:RMSesstionStart() The audit log file is not found.
> #(660)# 16:59:50 11/24/04 Normal : ZENUtil:
> ZENIsWorkstationRegistered: wsDN 'CN#(660)# 16:59:50 11/24/04 Normal :
> Workstation is registered
> #(660)# 16:59:50 11/24/04 Normal : ZENNDSUtil: Attempting to read
> policies...
> #(660)# 16:59:50 11/24/04 Normal : ZENUtil:
> ZENIsWorkstationRegistered: wsDN 'CN#(660)# 16:59:50 11/24/04 Normal :
> Workstation is registered
> #(660)# 16:59:50 11/24/04 Normal : Reading workstation DN and tree
> name...
> #(660)# 16:59:50 11/24/04 Normal : workstation DN -
> CN
> #(660)# 16:59:50 11/24/04 Normal : Loading : C:\Program
> Files\Novell\ZENworks\WMSchApi.dll
> #(660)# 16:59:50 11/24/04 Critical : ZENNDSUtil: Failed to load
> WMSchApi.dll. Error: 1114
> #(660)# 16:59:50 11/24/04 Normal : Reading workstation DN and tree
> name...
> #(660)# 16:59:50 11/24/04 Normal : workstation DN -
> CN
> #(660)# 16:59:50 11/24/04 Normal : Loading : C:\Program
> Files\Novell\ZENworks\WMSchApi.dll
> #(660)# 16:59:50 11/24/04 Critical : ZENNDSUtil: Failed to load
> WMSchApi.dll. Error: 1114
> #(660)# 16:59:50 11/24/04 Normal : Neither policy settings active.
> All operations disabled.
>
>
Just to support the previous person who also replied to this question. We
had the same problem and it was the path. Someone pushed an app that
replaced the path instead of appending to it and it killed the zen remote
agent. Replacing the path to "c:\program files\novell\zenworks" path worked.
Thanks much for the person who first suggested this.
Neal...

Bluetooth radio disables itself

My wife has a BlackBerry Pearl and since she is not on an enterprise server, I have it set up to connect to our home PC using Bluetooth. It works beautifully and will perform a wireless sync of her calendar and contacts whenever she is within range of the PC. The only problem is that the BT radio on the phone has a mind of its own and turns itself off after some time. I haven't determined if there is any sort of cue for it to turn itself off or not. I just know that every couple of days, I grab her phone to make sure that she has been syncronizing regularly (of course she doesn't) and the BT radio is off. I then enable the radio, at which point the PC prompts for a connection and the sync routine then launches.
I've seen other threads in this forum that talk about the BT radio disabling after a period of inactivity when connected to a headset. I would assume that this is the same problem. Any answers???

See if these KB articles are of any help:
http://www.blackberry.com/btsc/KB03874
http://www.blackberry.com/btsc/KB10513
http://www.blackberry.com/btsc/KB15976
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution.

LAP 1142N "Radio disabled due to PoE" after upgrade to 7.6.120

Recently, we upgraded our 5508 wireless controllers from 7.4.110.0 to 7.6.120.0.
One AP (AIR-LAP1142N-E-K9) doesn't work now.
Both radios are stuck in state 'reset':
AP#sh int dot11Radio 0 | inc Dot11Radio0
Dot11Radio0 is reset, line protocol is down
It seems to be a PoE issue:
AP#sh controllers dot11Radio 0
Radio disabled due to PoE
This 1142N is connected to a HP switch (model 3800 with 802.3af/802.3at support). It did work on this switch several months before this upgrade and it works if connected to Cisco switch (Cat 6513).
We didn't upgrade the switch firmware or change its configuration.
The PoE status from the switch CLI:
PoE    | Power Power    Alloc Alloc Actual Config   Detection   Power Pre-std
Port   | Enable Priority By    Power Power Type     Status      Class Detect
------ + ------ -------- ----- ----- ------ -------- ----------- ----- ------
21     | Yes    low      lldp 33 W 7.8 W           Delivering 3     off
Other APs (80 3602 connected to HP8212zl switches) do work without any problem.
Any idea how to solve this?

After updating to 7.6.120 we've noticed that some of our AP's wouldn't come up. After looking in the switch's logs I found this
chassis: Ports PoE usage has exceeded threshold of 80%.
The power drawn is 117w (show power-over-ethernet).
When I use the following command: show power-over-ethernet brief I get this:
PoE | Power Power Alloc Alloc Actual Configured Detection Power Pre-std
Port | Enable Priority By Power Power Type Status Class Detect
----- + ------ -------- ----- ----- ------ ----------- ----------- ----- ------
1 | Yes low lldp 17 W 7.0 W Delivering 3 off
2 | Yes low lldp 17 W 7.0 W Delivering 3 off
3 | Yes low lldp 17 W 6.8 W Delivering 3 off
4 | Yes low lldp 17 W 7.1 W Delivering 3 off
5 | Yes low lldp 17 W 7.0 W Delivering 3 off
6 | Yes low lldp 17 W 6.9 W Delivering 3 off
7 | Yes low lldp 17 W 6.8 W Delivering 3 off
8 | Yes low lldp 17 W 6.7 W Delivering 3 off
9 | Yes low lldp 17 W 6.9 W Delivering 3 off
10 | Yes low usage 17 W 0.0 W Disabled 3 off
Port 10 is where the missing AP is on.
How is it possible that after the update to 7.6.120 the AP won't work anymore?

'Import All' is disable at Image Capture

Hi!!
I just upgrade to Yosemite, and when I insert an SD (only photos) to my MacBook Pro, the Image Capture program shows up. But when I want to import all media, the button 'Import All' is disable.
Does any one knows why is happening this?
This is the same SD that I was using with my Canon, and did not had this problem with Mavericks.
Thanks a lot in advanced.

Thanks Glenn Leblanc!
I think there is a problem with the software.
I tried this:
1. Hide the 'Devices' list.
2. Show the 'Devices' list.
3. Then selected the SD, and magically the 'Import All' button became available.
Even if you select 1 file from the list, the button is available.
Greetings!!

ALL RADIO BUTTONS NOT SHOWING UP ON WEBSITES

WHEN I LOAD SOME WEB PAGES NOT ALL RADIO BUTTONS SHOW UP. HAVE TO SCROLL ALL OVER PAGE TO SEE IF ANYTHING SHOWS UP. IT HAPPENS ON A LOT OF SITES.

Make sure that you allow pages to choose their colors and that you haven't enabled High Contrast in the Windows Accessibility settings.
*http://kb.mozillazine.org/Website_colors_are_wrong
*http://kb.mozillazine.org/Websites_look_wrong

HT201210 what do yu mean by security software....is it all about disabling my antivirus....i need help on this

what do yu mean by security software....is it all about disabling my antivirus....i need help on this...cze my 3g is showing error 1015

See this discussion: https://discussions.apple.com/thread/5110212?tstart=0

Aironet 1100 Radio disabled at power up

Just setting up an Aironet 1100. Anytime I reboot (or if power is lost) it comes up with the "radio" disabled. I understand that this may be the default behavior before configuring but shouldn't it remember the settings so it reboots to the last state? I am sure it is not desired to have to reenable the radio on every AP after a power failure. What am I missing?
Thanks. Bruce
Model info and software versions below:
Product/Model Number: AIR-AP1121G-A-K9
Top Assembly Serial Number: FTX1033V144
System Software Filename: c1100-k9w7-tar.123-8.JEB1
System Software Version: 12.3(8)JEB1
Bootloader Version: 12.3(2)JA4

Thanks Mike:
I had seen that info about 12.3(4)---but thought that applied to default behavior and not whether it would explain losing the enabled status at every reboot.
Should I try to upgrade the bootloader to a newer version (can that be done, where are the files?). Some of the terminology is confusing. I wasn't sure if that applied to my system (12.3(2)JA4) since that talks about 12.3(4)JA2 having the radio disabled by default and no SSID.
I actually had tried to upload the newest system software (from JEB1) but that failed.
Does the system software upgrade also update the bootloader version or are they independant?
thanks for you help
Bruce

Cisco 1130 AG's - FastEthernet Radio Disabled

Hello,
I was looking through an 1130AG trying to shut down the radios for a day to do some other testing. I accessed these through the web browser. I disabled the A and B/G radios from the location and then went to another location and disabled FastEthernet (wired) connection. I want to bring these radios back up and now I can't access the web interface because I disabled the wireless connection. Can someone please help out and direct me where to go next to enable the radios on these access point (without hopefully resetting it) and without the ability to access through the web based interface??
Thanks so much for your help

Hi Dayne you are most welcome my friend! ... sorry for misspelling your name earlier (can't read or type sometimes :)
Here is some info for using Hyperterminal/Console connections
Console info;
http://www.cisco.com/en/US/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15frst.html#wp1034762
Cisco IOS Command Modes
The Cisco IOS user interface is divided into many different modes. The commands available to you depend on which mode you are currently in. Enter a question mark (?) at the system prompt to obtain a list of commands available for each command mode.
When you start a session on the access point, you begin in user mode, often called user EXEC mode. Only a limited subset of the commands are available in user EXEC mode. For example, most of the user EXEC commands are one-time commands, such as show commands, which show the current configuration status, and clear commands, which clear counters or interfaces. The user EXEC commands are not saved when the access point reboots.
To have access to all commands, you must enter privileged EXEC mode. Normally, you must enter a password to enter privileged EXEC mode. From this mode, you must enter privileged EXEC mode before you can enter the global configuration mode.
Using the configuration modes (global, interface, and line), you can make changes to the running configuration. If you save the configuration, these commands are stored and used when the access point reboots. To access the various configuration modes, you must start at global configuration mode. From global configuration mode, you can enter interface configuration mode and line configuration mode.
http://www.cisco.com/en/US/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15cli.html
Hope this helps!
Rob

FM radio & disabled audio settings

Is it just my L920 or audio settings (equalizer & enhancements) are disabled on all Lumias while listening to FM radio?
The silence will fall

DLSS wrote:
FM radio is analog. Are you guys sure it even gets converted to digital so the audio can be processed? You might be looking for workarounds needlessly.
None of the previous Nokia phones I owned allowed applying EQ to FM radio (and I believe this to be a smart choice).
To be honest, throwing a DAC at the audio coming from the FM Radio to convert it to digital, then passing it through a DSP for EQ and other processing, then sending it to a DAC to make it analog again doesn't make any sense from a power management standpoint - all these steps would require processing power.
Actually, I'm not looking for workarounds, just trying to find out if this is a bug on L920 or on all Lumias. This is why I created this topic. And you are right, as you can see from my previous posts, I'm not sure if the fm audio is processed or not.
I agree with you, technically those processing steps will require processing power, so does the glance screen and double tap to wake features. This doesn't mean it's not implemented on purpose.
From my point of view, as a lumia user, I cannot be sure if this is a bug or not without a feedback from other lumia users or technical experts from nokia/ms.
The silence will fall

Firefox crashes randomly even with all extensions disabled and new profile, but not in safe mode

Starting from about 2 weeks ago, Firefox has been crashing. The crashes is seemingly random, but normally happens when many pages/tabs are open. Also, all observed crashes happened in middle of some user operations. If I just leave it open(and loaded), it would never crash even after a long time.
Also, the crashes would still happen even after ALL extensions are disabled manually. However it doesn't seem to happen in Safe Mode.
After every crash, in the crash report dialog, the "Details" report would not respond. However I can open the reports using about:crashes.
Before the crash would happen, sometimes the following ill-behaviors could be observed:
* Firefox fails to render CJK characters, displaying them as square boxes instead
* CJK IME(Namely Google Pinyin, an IME for Simplified Chinese) could no longer be activated in Firefox, neither on a webpage element nor on UIs of Firefox itself(i.e. address bar or search bar)
The following has been tried but no luck:
* Disable ALL extensions manually
* Start a new profile
* Reset Firefox
* Uninstall/Reinstall Firefox
* Switch from FX 14 to 15, then to 16 beta

hello Rainarrow, some other users who have recently updated the graphics driver for their ati hardware (to ati catalyst version 12.8) have reported similar crashes. please try disabling hardware acceleration in firefox > options > advanced > general & see if this resolves the issue of frequent crashes for the moment.

Firefox constantly crashes even with almost all extentions disabled.

For months now Firefox has been crashing regularly. This seems to happen most when I am on pages like Google Images or Google Maps. Each time this happens I get the screen to restart Firefox and submit a crash report. After that process the "this is embarrassing" screen comes up but the tabs listed are old, sometimes by several days. I have disabled nearly every extension / plug-in. I am tired of having to babysit this program. It is a browser and I am just trying to browse the internet. I am not a user with a ton of extensions or other add-ins to Firefox. I use it almost "out of the box". I have had to reset Firefox in the past and I have had times where I have lost all of my open tabs. I am just about to the point of dumping Firefox for a browser which actually works. Firefox has become a very frustrating program to use. It is a browser. The user should not have to bend over backwards to keep it working.
I use Windows Vista Ultimate. I am submitting this from a different computer since Firefox just opens for a minute then crashes over and over and over again.

We need to see your crash reports from your other computer where Firefox is having the issue.
I don't know what OS the other computer is running but I'll put instructions for both Mac and Windows.
Windows
Press the following shortcut to get a Run window: [Windows] + [R]. This should bring up a window that contains a text field.
#In that text field, enter %APPDATA% and press Enter. An explorer window should open.
#From that explorer window, double-click on the ''Mozilla'' folder, then double-click on ''Firefox'' and then on ''Crash reports''. Double-click on ''submitted''.
#Now, you should see a list of files that contain reports. Go to ''View'' > ''Arrange Icons by'' > ''Modified'' to get the most recent files at the top of the window.
#Open the most recent 5 files with a text editor and copy the IDs.
#Paste each ID with '''bp-''' into the reply window on the forums.
Mac
#'''(OS X 10.6 or previous)''' Click the '''Finder''' icon in the dock. Your home folder will be selected. In the right side of the window, click the Library folder to open it. Then open the "Application Support" folder, the "Firefox" folder, the "Crash Reports" folder and finally the "submitted" folder. '''(OS X 10.7 or above)''' Click the '''Finder''' icon in the dock. On the menu bar, click the '''Go''' menu, hold down the '''option''' or '''alt''' key and select '''Library'''. A window will open containing your Library folder. Then open the "Application Support" folder, the "Firefox" folder, the "Crash Reports" folder and finally the "submitted" folder.
#Open the 5 most recent files with a text editor and copy the IDs.
#Paste each ID with '''bp-''' into the reply window on the forums.

Windows 8.1 finds printer in the other room but I have all sharing disabled.

I have everything I can see disabled for sharing. Everything in:
-Start > PC settings
-When I go to Start and type in 'homegroup', 'Network', 'workgroup', etc.
-This Computer > Network
-All file explorer folders and drives.
I think W8.1 installed like this.
I have a printer that's like 15 years old and worked fine in XP but couldn't get it to work with W8.1. I made a thread and we tried basically everything but I gave up and am getting a new printer. I'm waiting from the manufacturer if there's a universal
driver or if it definitely can't be used with W8.
But anyway, when I tried to print, Windows couldn't find the 15 year old printer and asked to 'install a printer?" When I hit yes, it tries to install the printer on a computer in the other room (I know because of the printer name). That printer IS
on a workgroup and can be printed from other computers here and most likely without a password or anything (but never printed from my PC using XP that I noticed).
I have "sharing and the ability to see other computers and devices on this network" turned off, so how did I
find the device? Is it because the device is set to share without a password and windows thinks it's doing me a favor by allowing me to see it despite it saying I have even seeing other devices blocked?
I don't want to share anything at all to the network/workgroup/homegroup. I installed W8.1 about a week ago and haven't retreived my XP data from my external because of possible unaware sharing.
And, I'm pretty sure the workgroup here is called WORKGROUP, and even though I don't think I'm sharing on it, it says I'm on WORKGROUP under my 'System', so I also changed that to random jumbled letters. Is that an extra step to insure no sharing or actually
prone to more accidental sharing, or it doesn't matter?
Any help appreciated. Thanks.

I might have figured it out sorta.
I could never get my Dell XPS 630 motherboard's onboard NIC to work with XP. Instead, I plugged my internet wire into a SMC1211TX add-on card that has a built-in driver and always worked.
In device manager, SMC1211TX is called "Realtek RTL8139/810x Family Fast Ethernet NIC". Device Manager shows the onboard NIC as "NVIDIA nForce Networking Controller" and it works with Windows 8.1.
I'm %98 sure that both cards don't have wireless capabilities. Although this site calls the SMC1211TX a wireless card and I read people installing drivers to make it wireless but I'm not sure if that requires additional hardware: [link]
All I can search out is people trying to add wireless to the Dell XPS 630's NVIDIA NIC and people saying that it does not come with wireless. I can't seem to find an exact model # for the onboard NVIDIA NIC to see if it has Ethernet, but according to this,
it has Ethernet [link]
Someone mentioned "Is the printer on Ethernet, or is it connected directly to a PC? If it's on Ethernet, anything on the local network can see it."
The printer has a fax line from the wall phone jack, power cords, and the data cable's USB'd to the computer in the other room. The printer has Wireless enabled. The computer that the printer's plugged into might have an Ethernet card (I checked network
controllers in Device Manager etc on that PC and didn't see the word Ethernet, but it might be). So, I turned off the computer in the other room that the printer's connected to, but I still found the printer when I tried to print when using my Realtek RTL8139/810x
Family Fast Ethernet NIC. So I'm thinking that maybe since that NIC has Ethernet that I'm also getting wireless by being connected to a wireless router and it picks up the wireless printer? And that this still doesn't breach me sharing anything from my computer
because everything's private right?
I also plugged into the onboard NVIDIA NIC. I tried to print and see if the onboard card would find the printer in the other room and it did; however, when I tried a few more times, it wouldn't find the printer anymore, so I thought maybe this card doesn't
have Ethernet and that's why I could still find the printer with the other Ethernet card. But then even after rebooting a few times, I could still find the printer with the NVIDIA NIC with the computer in the other room turned off, so I'm thinking that maybe
the NVIDIA NIC also has Ethernet? Or that maybe it doesn't and it only tried to install the printer because the info was cached from using the Realtek RTL8139/810x Family Fast Ethernet NIC?
Also worth mentioning that the first thing I did after installing 8.1 was download drivers (chipset first then BIOS then one or two others). The only chipset driver from Dell was for XP so I tried it anyway but it didn't install. The BIOS flash seemed to work.
I tried their automated assistant to find and install drivers but it just showed the same XP drivers.

3600 AP %CDP_PD-2-POWER_LOW: All radios disabled

Similar Messages

Maybe you are looking for