3700+ san diego core and msi k8n neo2 platinum bios

will i need a bios update to get my 3700+ san diego core to work in my system. currently my motherboard bios is 1.5 Fedex sometime today is suppose to drop off my new 3700+ san diego core today. if i do need a bios, were can i get one for it to work.

Quote from: JCLogix on 05-May-05, 16:12:24
Offcially that board does not have support for San Diego at this time, so if you have got it working, as some people have it may have some wierd and wonderful effects on your system.
A guy on another forum got a response from a MSI tech that said they were working on it and to check their site regularly for a bios update. As far as "weird and wonderful effects" my setup has never run faster or smooter since I upgraded from my 3500+ Winchester. This is the 3rd day I've been running the San Diego, have had no problems other then having to use A64 tweaker to set RAM timing to 1T. 500Mhz overclock stock voltage, air-cooled, prime stable, I ran the torture test for 9 hours overnight!
Check it out!

Similar Messages

When will the MSI K8N Neo2 Platinum BIOS 1.C be released?

Hello
When will the MSI K8N Neo2 Platinum BIOS 1.C be released?
Thanks
FearTec

Don´t know the reason for you guys, for updating bios, but basically I would recommend Syars modded EasyBios, based on the 1C3 (1C0) version.
Check out the link in Syars sig or read it here;
https://forum-en.msi.com/index.php?topic=59711.0
and read about the differant version and you´ll get a pretty good idea whats changed and added.

MSI K8n Neo2 Platinum, bios accses

Read some where that if u, while inside the bios, enterd some key combinations could acces some more bios options on this board, anyone that knows anything about this?
If so, please let me know
//KennyK

https://forum-en.msi.com/index.php?topic=63137.0

Reboot problem with MSI K8N Neo2 Platinum and 250 GB SATA HDD

I'm having a "reboot" problem with my MSI K8N Neo2 Platinum. After turning my system on it will run without any problems, until I reboot. After a reboot it will always hang after the initial windows-bootscreen. The HDD-light will remain on. If, instead of going into Windows XP SP2, I try to enter the BIOS after a reboot (DEL) the system will also hang (blank screen with blinking cursor).
It started doing this after I installed the Maxtor 250 GB SATA disk. Before, I didn't have problems rebooting. If I disconnect the Maxtor drive I can reboot and enter BIOS and Windows each and every time. Reconnecting the Maxtor 250 GB SATA drive will return the reboot problem. I always have to use the power swith to get a working system again. It's not enough to do a hard reset (this has the same effect as rebooting).
Here are the details of my system:
MSI K8N Neo2 Platinum (BIOS 1.B)
Athlon 64 3200+ (Winchester, 2 Ghz, 512 KB cache, stepping DH-D0)
2 x Kingston KVR400X64C25/512, 512 MB, DDR, PC3200 (2,5-3-3-8 T1)
Asus Radeon AX800 Pro (256 MB)
PSU Antec Sonata 380W
HDD Maxtor 80Gb ATA (6Y080P0, Pri Master)
HDD Seagate 250Gb SATA (ST3200822AS)
HDD Maxtor 250Gb SATA (6V250F0 - jumpered in SATA150 mode, the mobo wouldn't work with the drive in SATA300-mode)
Aopen COM5232/AAH Pro CD-Writer ATA (Sec Master)
BenQ DW1640 DVD-Writer ATA (Sec Slave)
P.S. The NVidia IDE-drivers are NOT installed. System is not overclocked.

Thank you for all the replies. Upgrading to the latest Nvidia IDE-drivers did not fix my problem. Moving to other SATA-ports did not help either. Upgrading the mobo's BIOS is not really an option (I'm using one version before the most recent and there isn't anything in the fixlist of the latest BIOS).
Now I've contacted Maxtor for (hopefully) a new firmware.
Quote from: rogueUK on 31-July-06, 16:55:42
insego please use the SEARCH BUTTON
I did use the search function to find other people with similar problems. The reason I started a topic of my own was because of the text you get while joining:
Quote
Do not hijack another persons topic. If you have a similar problem, start your own thread anyway.
Maybe in retrospect I should first have tried the solutions in other topics.

MSI K8N Neo2 Platinum (WAKE On Lan with Realtek)?

Hello can the MSI K8N Neo2 Platinum (BIOS 1.B) WAKE On Lan with the Realtek card?
It does not appear to work for me and there is nothing in the BIOS.
My WOL packets wake up other PC's.
Please Help.

Hello !
Go into Bios Setup, Integrated Periphals, and disable the nvidia Lan, but let the Onboard LAN enabled.
Now go to PCI Configuration, Wakeup Events, and enable wakeup on PCI event and wake on LAN.
Check in Boot Order Menu if you can select the realtek onboard Lan as first booting device, push it in first place.
Another Option could be using the nvidia Lan, its reported to work with wakeon lan.
Greetz

MSI K8N Neo2 Platinum and Venice E6

Hi!
I have just bought an MSI K8N Neo2 Platinum motherboard and an AMD Athlon64 3000+ processor with Venice E6 core (ADA3000DAA4BW).
Will this mobo boot with that processor? Or do i have to use a Winchester to flash the BIOS first? Personal experiences would be helpful!
Andres.

Your new board probably came with the 1.9 bios. The new 7025v1B.zip bios (1B only a couple days old) I think is for some of the new X2 AMD Processors. The MSI link to Products/Mainboards/Neo2/Processor Compatibility is now setup to use the 7025v1B.zip bios. As I recall the previous Processor Compatibility Chart for 1.9 bios was OK for all the Venice cores (E6 or not). I think it is only some of the latest E6 bigger models are affected by the latest 1B bios. Maybe someone has the older 1.9 bios Processor Compatibility Chart.
You shouldn't need to use a Winchester, some X2 processors would be recognized as earlier X1 models until the newer bios was installed. I think you should be OK with the 1.9 bios. I have the San Diego 4000+ and my board, one month old, came with the 1.9 bios installed.

MSI K8N Neo2 Platinum AND SATA2

i have MSI K8N Neo2 Platinum motherboard with 3500+ cpu and WD 160 hard sata disk.
I 'd like to ask if my MSI K8N Neo2 Platinum motherboard support sata2 hard disk drives, in order to know which HD to connect as a second HD drive, SATA or SATA 2 ??

It'll see SATA2 as regular SATA. You won't loose any speed either. There are no hard drives that actually benefit from SATA2 spec speeds. Well, maybe in isolated near theoretical benchmark cases one current model might be faster in SATA2 mode.
We just haven't got the technology yet.

Msi k8n neo2 platinum and corsair cmx512-3200LL

is anyone using the corsair cmx512-3200LL with the msi k8n neo2 platinum or any other motherboards? if so how well does that memory overclock for you?

LL used winbond CH-5 or BH-5 or Infineon B-5 depending on revision .
And everybody knows that it's hard to overclock winbond very far without excessive vdimm increase (2.9v - 3.4v).
Corsair XL use samsung TCCD and overclocks much easier when having a motherboard with a vdimm limit at 2.85v.
xms 4xxx also use samsung (TCCC or TCCD) and some versions use hynix D43/D5
so you can't directly compare xms3200LL with the others .
You can query RamGuy about the chips used on the spesific modules here :
http://www.houseofhelp.com/forums/showthread.php?t=35940&page=1&pp=15
Note the Part , version , and lot number before posting .

Best ram for MSI K8N Neo2 Platinum Edition?

Ho guys
Im getting a MSI K8N Neo2 Platinum Edition this week but cant decide what memory to use what is the best memory for this board here
are my options.
http://www.stegcomputer.ch/details.asp?prodid=kin-KHX32-1c2
http://www.brack.ch/aspx/default.aspx?ID=17879&mod=artikel
http://www.brack.ch/aspx/default.aspx?ID=17636&mod=artikel
http://www.brack.ch/aspx/default.aspx?ID=17885&mod=artikel
http://www.1000ordi.ch/2500
I will be overclocking.
Any help would be appreciated

Quote from: mehdi on 13-July-05, 22:09:22
XL's is verified by anand to top at 2-3-3 on DDR466 so this would be how much of a oce on a 3700sandy at those timings.
Well the 3700 San Diego har a max multilplier equals 11 and you can use the lower ones also .
So you have more options than one to reach say you set a goal for 2700mhz assuming you have air cooling (2.7ghz seems to be what most aim for without extreme cooling)
HTT reference clock at 233 with memory index 200 times multiplier 11 gives 2530mhz on the cpu and 233mhz/466DDR on the memory .
To maintain same memory speed (around or below 233mhz) with higher cpu frequency you must use a divider by setting max memory speed to 166 etc and use a higher HTT clock reference .
E.g
HTT=270
Multiplier=10
Memory index=166
Gives CPU/12 divider
CPU is then 2.7ghz
Memory speed = cpuspeed/12 = 2700/12 = 225mhz or DDR450 .
Multilplier memory index dividers:
7x with 133 : cpu/11
8x with 133 : cpu/12
9X with 133 : cpu/14
10x with 133 : cpu/15
11x with 133 : cpu/17
7x with 166 : cpu/9
8x with 166 : cpu/10
9X with 166 : cpu/11
10x with 166 : cpu/12
11x with 166 : cpu/13
7x with 183 : cpu/8
8x with 183 : cpu/9
9X with 183 : cpu/10
10x with 183 : cpu/11
11x with 183 : cpu/13
7x with 200 : cpu/7
8x with 200 : cpu/8
9X with 200 : cpu/9
10x with 200 : cpu/10
11x with 200 : cpu/11
( with 200 you will se the divider is the same as multiplier , thats why some calls this 1:1 )
There are also some tables for the dividers made by orcar wu over at extremesystems in this thread:
http://www.xtremesystems.org/forums/showthread.php?t=41595&highlight=a64+divider+table]
Using this calculation you can figure out your ram frequency before trying it in the bios .
E.g use 183 mem index/divider with cpu multiplier 10x with 2.7ghz as the target .
10 x 270 = 2700
memory will run at
2700/11 = ~ 245mhz or DDR490

News - BIG PROBLEM - MSI K8N Neo2 Platinum - DOES NOT POWER!!!

Hi to everyone.
I'm a proudly owner of a MSI K8N Neo2 Platinum that in one year gave me no problem until yesterday morning.
I used the computer in the night before and when I finished I turned it off and I went to bed.
Yesterday morning I found the power led blinking (like if the system was in standby), and there was no way to turn the PC on.
I even took off the battery for more than 12 hours and I left only minimal components installed:
the video card (Gainward GeForce 6800),
the psu (Antec TruePower 550W),
1 x 512 MB Ram Crucial Ballistix,
and I checked them into another computer and they work perfectly.
I tried shorting the MB power switch pins with a screwdriver and I've even tried to power on the system without the Memory or the Video Card... I've tried everything that came across my mind with no efforts!!!!
Every time I give power to the MB appens only that the power led starts blinking, but pressing the button the PC doesn't turn on.
PLEASE HELP ME... I really don't know what else to do!!!
Thanks,
Alberto

Quote from: alberto_melita on 20-August-05, 20:14:56
Hi thanks for the answers.
I do have a D-Bracket, but my problem is not that the system does not boot or does not post... my system DOES NOT POWER ON (!!!!), so d-bracket is useless!
When I plug the system power the only thing that happens is that the power led starts blinking (with the system still in soft-off), and if I press the power switch button nothing happens!
I've the bios for 7025 v1.8 and the settings where for OFF on power-loss ond pressing the button (can't rememeber if it was more than 4 sec) was meant to turn off the computer, but considering that I un-powered the pc more than once without the MB battery the settings should be factory default by now.
I went through the Windows-XP shut-down system, and i could not be an electrical problem as I always used the PC with a pretty good UPS unit.
Right now these are the full specs of my sytem:
- MB MSI K8N Neo2 Platinum nForce3 Ultra
- GAINWARD 6800 2600 GLH 256 MB Ram
- PSU Antec TruPower 550 W
- CPU AMD64 3500+ core Winchester @11*210 Mhz (this cpu has never overclocked very well)
- HEATSINK Thermalright XP-90 with a 12 Cm Enermax Fan (CPU temp in always below 55 °C when stressed)
- 1 x 512 Mb RAM Crucial Ballistix DDR400 optimized for MSI K8N Neo2 Platinum
I left only these things inside my computer in the hope that it would turn on... it did not work. I tested each component but the MB, and they work perfectly.
Again...
Thanks for you efforts, any help will be appreciated.
Alberto.
All parts have been tested: CPU/RAM/GFX/PSU/HD/DVD, just not the MOBO ?
Checked if the MOBO is shorting in the case ?
Have you tried using the reset switch as power, on/off switch ? I've seen before when the power switch stops working (lose/bad wire busted spring) after swapping reset to power, then the system turned on. Worth a try, as sending it back to USA won't be cheap. If its over 1 year old it mite not be covered by the re-seller and or MSI. Best to check this out as law and warranty is different from country to country.
Good Luck

New CPU, Msi K8n neo2 platinum - no boot!

Greetings!
I got the following components:
*MSI K8N NEO2 Platinum -54g MB
*4 x 512mb Geil Value Ram
*Gainward 7800GS+ Bliss 512mb AGP
*Samsung Spinpoint 500gb SATA HD
*Corsair 620HX (620W) PSU
*CPU AMD Opteron 180 Dual Core (upgrade from AMD 3000+ Winchester)
I recently upgraded my PC with a new HD, more ram, new CU Fan/heatsink - on an AMD 3000+ (Winchester). PC wouldn't boot - I did however manage to fix it. I think it was because of the ram, one of the bricks had some dust on it. Since then, my pc has worked 100%...
Today, however, I got a new PSU and CPU in the mail! A Corsair 620W PSU and an AMD OPTERON 180 Dual. I carefully cleaned the surface on the heatsink etc, and applied an appropriate amount of "Arctic Alumina" on the CPU/heatsink (as followed per instructions from Arctic). When I have connected everything, and fire my pc up - it just won't boot.. (The monitor won't light up).
Since then, I have carefully checked all wires, unplugged/replugged etc.
But it just won't boot!
I do have the latest bios (1.0D), so it should support my CPU.
I should mention some "weird" things, though. When I try to boot up, everything seems normal (All fans are running), but there are no lights on my case! And I can't turn off the PC while holding down the "power" button on my case. I can't reset either.. as soon as I turn the PC on (by turning on the PSU power switch), the PC starts running. Normally I would have to push the button on my case. ALSO: I have cleared CMOS, still a black screen. And I have tried 2 different monitors, so I know it aint that either.
My old PSU was a Chieftec 360W one (and my case is a Chieftec also). The old PSU was connected to "SFAN2" on my MB,.. my new PSU isn't connected to any "SFAN" at all.. I doubt that has anything to do with the problem though?
Any suggestions on what I might do ?
Edit: D-bracket shows this (Yellow, red, red, yellow):
BIOS Sign On
- This will start showing information about logo, processor brand name, etc... - It stops here. No boot screen

Quote from: BOSSKILLER on 14-November-07, 21:14:42
remove power cord from the PSU(else will not work) and Clear CMOS Guide.
leave one memory stick only in a 1st DIMM slot near to CPU socket and try to boot.
Done & done.
Still no boot screen :(

NOOB -MSI K8N NEO2 Platinum questions

Hi
I coming from an Intel background but am now considering changing to AMD; i'd like to keep my agp x800xt pe card and get a MSI K8N NEO2 Platinum board but have got a few questions /concerns.
I have looked on several forums including MSI's own forum and noticed people having problems with corsair value select memory modules.
My questions which i'd be grateful for answers to are:
1. Am gamer and planning to also purchase a 4000+ to put in it - will the board recognise it straight away or will I need to update BIOS..
2. Want to transfer my current 4x512mb 3200 Corsair Value Select sticks to my new board - will there be any compatibility problems? (cannot afford to buy new memory)
3. Will I be able to run the memory 200 + ? as heard the boards base clock for a 4000+ is 166
4. If I can run these at 200 can i do this straight away or will i need to overclock them slowly to get to 200 (will the board see them as 3200 and start at 200?)
5. Anything else I should know/look out for?
Many thanks to all. My first post here so hello to everyone.

Hello !!
Let´s try to answer your questions...
1. It depends on which Bios Version is installed out of the Box, i suggest version 1.8, if you are not using a Venice / Dual-Core or later CPU Core. The advantages of biosses later than version 1.8 are the new Steppings Support and some new Memory Timing Options available in Bios Setup.
2. I do not know exactly, i think most corsair sticks are running well on this Board if you are not going to overclock. But it depends on which Chips are used your Corsair Modules. What could be a problem is that you are going to use 4 Ram Sticks, because with Winchester Cores you would not be able to run 4 Sticks in PC3200Dual Channel Mode (DDR333), even if your Ram would be 100% compatible with your MOBO. Venice and later Cores are able to handle 4 sticks at 400Mhz DDR clock. Except you own 4 single sided Ram Modules.
3. Should be possible if your memory likes it.....
4. No, the Bios will recognize your SPD Timings. So you will have to overclock them from a 166Mhz Memory Divider Base.
5. Take a look here:
http://xtremesystems.org/forums/showthread.php?t=46730
https://forum-en.msi.com/index.php?topic=72024.0
http://www.msi.com.tw/html/products/mainboard/testreport_pdf/7025/memory.pdf
Good Luck
Greetz MurdoK

System suddenly won't power on (MSI K8N NEO2 PLATINUM NFORCE3)

System specs are
COOLERMASTER TAC-T01 WAVE MASTER ALUMINUM ATX 4X5.25 1X3.5 4X3.5INT case
MSI K8N NEO2 PLATINUM NFORCE3 ULTRA S939 AGP 5PCI SATA 1394 SOUND 1000LAN
KINGSTON HYPERX 1024MB DUAL CHANNEL KIT PC3500 2X512MB DDR 433MHZ 184PIN
ATI Radeon X800XT PE AGP
SEAGATE BARRACUDA 7200.7 200GB SATA 8MB 7200RPM 8.5MS OEM
CREATIVE SOUND BLASTER AUDIGY 2 ZS 7.1 1394 PCI RETAIL BOX
LITEON 16X DVD-ROM INT E-IDE RETAIl
MITSUMI FA404A 7-IN-1 FLOPPY DRIVE & FLASH READER CF/SM/SD/MMC/MS
LG 4163b dvd burner
Nothing has ever been overclocked on this system.
Everything is plugged into a Belkin Surgemaster powerbar.
I haven't mentioned the power supply. I'll get to that. I have been using an ANTEC NEOPOWER 480W POWER SUPPLY (ATX12V DUAL 12V RAILS ACTIVE PFC W/ DETACHABLE OUTPUT CABLES) for about a year on this system without
any issues. One morning, I wake up, hit the power button on my coolermaster case, and nothing happens.
CPU fan won't even spin. Nothing happens.
O.k., blown power supply, I think . . . .
So I take out my Antec and put it in another system. That system turns on
without any problems.
Hmm . . .
I come here, and I read posts about
potential compatibility issues with Antec power supplies. But if it's a compatibility
issue why was my system working for about a year?
O.k., fine. I'll buy a Enermax 535W EG565P-VE FMA 24P (115/230 VAC) power supply.
I just plug it into the mainboard (nothing else). Hit the power button . . .
The CPU fan spins for half a second, and then nothing.
Did my motherboard just suddenly die for no reason?
Any suggestions?

Pull the AC plug from PSU and set cmos in clear position with battery removed for atlest 20 minutes perhaps longer .
Then try to post the system barebone .
Just cpu,1 pcs memory in slot 1 , gfx card , and keyboard in PS2.
No usb devices at all including card reader and no pci cards harddisks or cdoms/dvd/floppy.
It could also be caused by a short or a malfunctioning fan connected to mobo.
Try to disconnect all case fans from mobo headers if you have any connected to additional fan holders.
The chipset fan can also be disconnected momentarily just to see if it posts.
If none of this helps , replace cmos battery and try again .

MSI K8N Neo2 Platinum Fan

For some reason the small chipset fan on my MSI K8N Neo2 Platinum mobo has become a lot louder, I think it is running at higher RPMs that before. It starts up loud even if the computer is doing a cold boot from room temperature. Is there anyway to control this fan speed and quiet it down? and if I slow it down, will it hurt my motherboard? This fan is now louder than my graphics card fan, which makes it the loudest fan in my case even though it is the smallest.

Quote
Originally posted by Brogan
You could always replace it with a Zalman hedgehog.
I did.
Thanks for you reply, the only problem with the Zalman is that it's really big and I think my MSI NX6800GT's cooler would get in the way.

MSI K8N Neo2 Platinum slows down

Hi,
I have a little problem with my new K8N Neo2 Platinum. I installed Windows XP and the newest nForce drivers but if I copy files over LAN (tested both LAN-Ports) or install big applications my music played with winamp slows down. It's played with half speed. In addition to that my mouse pointer is very slow. After the setup or copying files everything is how it should be again. How can I solve this problem?
My system:
AMD Athlon64 3500+ (Winchester)
MSI K8N Neo2 Platinum-54G (tried different bios releases)
1024MB Corsair XMS Twinx DDR500
ATi Radeon 9800 Pro
2 80GB Maxtor S-ATA (DMA Mode enabled)
Creative Labs SoundBlaster Live! Player 5.1
MorLipf

Hello,
I copy files to my bro sometimes, 5Gb - all the steam GCF files for CS/HL/CSS/HL2.
My network usage is 80%-92%
My CPU usage is always under 15%.
It is worse when using 512Mb but as you have 1Gb it shouldn't be bad.
Check in the device manager, your cd drives should be set to DMA mode.

3700+ san diego core and msi k8n neo2 platinum bios

Similar Messages

Maybe you are looking for