3702i won't join controller
Just unboxed my first new 3700 AP. Fired it up and it doesn't appar to like my controller. Anyone have any suggestions?
IOS Bootloader - Starting system.
flash is writable
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 12 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 7354880
flashfs[0]: Bytes available: 33803776
flashfs[0]: flashfs fsck took 10 seconds.
Base Ethernet MAC address: 3c:08:f6:6c:f5:04
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...##########################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 12 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 7354880
flashfs[0]: Bytes available: 33803776
flashfs[0]: flashfs fsck took 10 seconds.
Base Ethernet MAC address: 3c:08:f6:6c:f5:04
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx;flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...######################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Sat 16-Nov-13 10:46 by prod_rel_team
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 12 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 7354880
flashfs[2]: Bytes available: 33545728
flashfs[2]: flashfs fsck took 10 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete.
Copying radio files from flash: to ram:
%Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/R2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/Q2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/C2.bin (No such file or directory)
Uncompressing radio files...
File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/R5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/Q5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/C5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/8006.img
...done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
no ip http server
^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3702I-A-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FTX175071RZ
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.1.118
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 3C:08:F6:6C:F5:04
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17482H3B
Top Assembly Part Number : 068-05054-01
Top Assembly Serial Number : FTX175071RZ
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-A-K9
% Please define a domain-name first.
Press RETURN to get started!
APAVC: Initial WLAN Buffers Given to System is 2500
APAVC: WlanPAKs 18174 RadioPaks 17566
set_radio_pwr_mode: bad radio unit# 0
set_radio_pwr_mode: bad radio unit# 1
*Mar 1 00:00:13.663: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:15.707: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:16.067: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Sat 16-Nov-13 10:46 by prod_rel_team
*Mar 1 00:00:16.107: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:16.107: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default configlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:16.231: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:17.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to upERROR: Failed to configure ethernet promiscuous mode. Interface Descriptor mismatch
*Mar 1 00:00:20.919: DPAA Initialization Complete
*Mar 1 00:00:20.919: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:21.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:34.859: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:53.751: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.13.1.85, mask 255.255.254.0, hostname AP3c08.f66c.f504
Translating "CISCO-CAPWAP-CONTROLLER.childrenshc.org"...domain server (10.12.18.255)
*Mar 1 00:01:03.731: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.11.0.210 obtained through DHCP
*Mar 1 00:01:03.731: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.11.0.212 obtained through DHCP
*Mar 1 00:01:03.731: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:03.731: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.childrenshc.org
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'c5508-2.cpt'running version 7.5.102.0 is rejected.
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.11.0.212
*Mar 1 00:01:13.735: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'c5508-2.cpt'running version 7.5.102.0 is rejected.
*Mar 1 00:01:13.735: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
Just confirmed with the Cisco guys, thats a mistake. 7.6 code is needed, 7.5 not supported with 3700.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."
Similar Messages
-
Cisco AP1142N won't join controller
Hi
When upgrading one of our WISM controller cards a problem occurred with some AP1142N.
The can’t join controller with 7.6.120.0, upgrading was from 7.4.121.0
When CLI into the AP I got this messages:
Reboot and tries to connect to the WISM2 with 7.6.120.0, but it fails.
Then tries to connect to another WISM2 with 7.4.121.0 and this work
But then the image on the AP is not correct (have a 7.6.120.0 image)
Downgrading AP to 7.4.121.0 image
Reboot and are back to number 1.
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I '(index 0).
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:29.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
Translating "CISCO-CAPWAP-CONTROLLER.net.yyyy.se"...domain server (xxx.xxx.xxx.xxx) [OK]
*Mar 1 00:00:59.550: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I '(index 0).
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:29.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Sep 10 11:25:59.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.17.16.25:5246
*Sep 10 11:26:00.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I (index 0).
*Sep 10 11:26:00.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:30.000: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
examining image...
extracting info (292 bytes)
Image info:
Version Suffix: k9w8-.124-23c.JA8
Image Name: c1140-k9w8-mx.124-23c.JA8
Version Directory: c1140-k9w8-mx.124-23c.JA8
Ios Image Size: 4915712
Total Image Size: 5110272
Image Feature: WIRELESS LAN|LWAPP
Image Family: C1140
Wireless Switch Management Version: 7.0.250.0
Extracting files...
c1140-k9w8-mx.124-23c.JA8/ (directory) 0 (bytes)
extracting c1140-k9w8-mx.124-23c.JA8/T5.bin (23836 bytes)
*Sep 10 11
extracting c1140-k9w8-mx.124-23c.JA8/8001.img (174932 bytes):25:59.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.17.16.25:5246With a WISM, you have by definition an etherchannel between your controller & APs. Try setting the load balancing algorithm on the switch housing the WISM to src-dst-mac before connecting the AP. There is/was an issue that shows itself rarely where other load balancing mechanisms interfere with an AP's initial join to a controller. The problem declined significantly over the years, but you may be running into it.
Once the AP joins, you can reset your load balancing and you shouldn't have the problem even if the AP reboots later. It usually impacts APs that have never joined your controller. Don't know why. Since this was an upgrade it may not be your problem, but it won't hurt to try. -
1242 is not joining controller
hello friends,
i have 1240 series access points which is not joining controller 5500 series..
here is logs at joining time below
AP503d.e56e.e7be#Xmodem file system is available.
flashfs[0]: 7 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 2649600
flashfs[0]: Bytes available: 13349376
flashfs[0]: flashfs fsck took 25 seconds.
Base ethernet MAC Address: 50:3d:e5:6e:e7:be
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button is pressed, wait for button to be released...
button pressed for 37 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1240-k9w7-tar.default
examining image...
%Error opening (connection timed out)Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...#############################################################################################################################################
File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 2632192
flashfs[1]: Bytes available: 13366784
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-E-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ150482DL
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 50:3D:E5:6E:E7:BE
Part Number : 73-10256-07
PCA Assembly Number : 800-26918-06
PCA Revision Number : A0
PCB Serial Number : FOC150158MH
Top Assembly Part Number : 800-29152-03
Top Assembly Serial Number : FCZ150482DL
Top Revision Number : A0
Product/Model Number : AIR-LAP1242AG-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:05.426: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 34 messages)
*Mar 1 00:00:07.500: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:07.526: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
*Mar 1 00:00:07.601: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:08.500: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:12.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
AP503d.e56e.e7be#
*Mar 1 00:00:46.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
AP503d.e56e.e7be#
AP503d.e56e.e7be#
AP503d.e56e.e7be#sh ver
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
AP503d.e56e.e7be uptime is 0 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-E-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ150482DL
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 50:3D:E5:6E:E7:BE
Part Number : 73-10256-07
PCA Assembly Number : 800-26918-06
PCA Revision Number : A0
PCB Serial Number : FOC150158MH
Top Assembly Part Number : 800-29152-03
Top Assembly Serial Number : FCZ150482DL
--More--
*Mar 1 00:00:56.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not haveTop Revision Number : A0
Product/Model Number : AIR-LAP1242AG-E-K9
Configuration register is 0xF
AP503d.e56e.e7be#
*Mar 1 00:01:06.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
any advice please??
thanksIt sounds like you are still working out IP connectivity, but I also noticed your AP is not for US regulatory domain.
Can you confirm that your WLC is ready to accept an AP with country code -E?
Your AP model: AIR-LAP1242AG-E-K9
From the WLC CLI
>show country
If you are in US, you should only have -A available. If this AP is intended to be used the US, then you will need to acquire an AP with the correct country code, as -E would not be supported in the US -A regulatory domain and should not be used. Perhaps this is for another location, so you may need to add the applicable regulatory domain support.
This link provides the list of the respective country codes and compatbility/etc.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps6087_Products_Data_Sheet.html -
I have a new Macbook Pro. It can see, but won't join the open wireless networks that my existing Macbook Pro joins. What can I do, please?
Mac OS X 10.7 Help: Troubleshoot a network printer
-
Flexconnect AP not joining Controller
Hi Community ,
I have some flexconnect APs in remote side . But they are not able to join controller 5508 (7.6) and flexconnect is also showing down in PI.
Any reason ??Hi Adam ,
Thanks for your reply .
Scenario is that we have 2 controllers in HQ . Controllers running IOS code 7.6 . APs are 1242 LAP . They were working fine just one week ago . But now I can see them they are not in the controller , though up . When I checked in PI , Flexconnect status showing down . Hope this will help . -
My iMac won't join the correct network
This is a new iMac with Lion. The network is ok because all my other devices work fine with it. The network is in the list and when I select it my mac joins without problem, but won't join it automatically. I've also tried to move my network up in the list but that doesn't seem to work either.
Mine is the only network listed in the Perferred Networks List in the advanced settings. The "Remember networks this computer has joined" is checked.
The problem is that when I wake my computer up, it won't find the network. I updated my airport extreme last week and this problem started after that. However, none of the other devices using this network are having any problems. -
Hi all
I'm having an issue with a 1252 LAP that is connected to the WLC over a WAN link.
Basically, it won't associate. The following is taken from a console into the LAP:
*Mar 1 00:00:07.799: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:08.799: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.851: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:27.003: Logging LWAPP message to 255.255.255.255.
%CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
%CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
%DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.148.x.x, mask 255.255.255.0, hostname AP002
2.90a3.533a
Translating "CISCO-LWAPP-CONTROLLER.nation.radix"...domain server (10.x.x.x)
%LWAPP-3-CLIENTEVENTLOG: Controller address 10.x.x.x obtained through DHCP
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.nation.radix
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER.nation.radix
%LWAPP-5-CHANGED: LWAPP changed state to JOIN
%LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller - Fxxxxxxx)
%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
%LWAPP-5-CHANGED: LWAPP changed state to DOWN
IOS Bootloader - Starting system.
Xmodem file system is available.
The ap-manager interface is configured correctly and there isn't a duplicate IP address.
The LAP was initially stand alone and was converted to LWAPP.
The MTU over the WAN link is 1500 bytes.
All I'm getting from the WLC debugs is:
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Received LWAPP DISCOVERY REQUEST from AP 00:22:xx:xx:xx:xx to 00:19:xx:xx:xx:xx on port '29'
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx LWAPP Discovery Request AP Software Version: 0x3003300
Mon Jul 20 11:42:59 2009: 00:22:xx:xx:xx:xx Successful transmission of LWAPP Discovery Response to AP 00:22:xx:xx:xx:xx on port 29
So basically the join messages don't seem to reach the WLC. In fact they don't even seem to reach the local router on the remote subnet. The discovery packets are seen on the local router but the joins don't seem to appear at all.
I'm not sure if it's a latency issue. Average latency over the WAN link is under 70ms.
I'm assuming the certificate on the WAP is MIC and the MAC details have been entered into the WLC AP Security policies for authentication. I'm not seeing any debugging messages relating to bad authentication at all.
I can't debug from the LAP as it's LWAPP, obviously.
I've been through many Cisco documents trying to troubleshoot the problem, including this http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml, but can't find a solution.
We're running WLC version 4.2.130.0.
Can anyone help?
Thanks
BrodieI assume you have connected to router's AUX and doing reverse telnet. You should be getting Password: prompt on your LAP's console. Password and Enable are both Cisco. Below is console output from my lab's 1250 LAP after erasing configuration (which can only be initiated from controller). In my case, the vlan is not configured with Option 43 and no proper DNS, so LAP doesn't join the controller.
By the way, your best bet might be to convert this LAP back to IOS and then back to LAP again. Use this method:
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Do you have "Authorize APs against AAA" checked under Security > AP Policies in any of your WLCs ?
Press RETURN to get started!
*Mar 1 00:00:07.099: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.619: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:08.595: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*May 10 23:17:25.199: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*May 10 23:17:26.155: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W8-M), Version 12.4(10b)JDC, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Fri 01-May-09 10:49 by prod_rel_team
*May 10 23:17:26.155: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*May 10 23:17:27.183: %SSH-5-ENABLED: SSH 2.0 has been enabled
*May 10 23:17:27.387: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*May 10 23:17:27.387: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*May 10 23:17:28.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*May 10 23:17:28.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*May 10 23:17:30.783: %LWAPP-3-CLIENTERRORLOG: ../lwapp/lwapp_l2.c:152 - discarding msg type 12 in state 0
*May 10 23:17:30.783: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*May 10 23:17:30.795: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 16 seconds
*May 10 23:17:44.571: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*May 10 23:17:44.731: Logging LWAPP message to 255.255.255.255.
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
%DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.8.3, mask 255.255.255.0, hostname AP0022.558e.24bc
User Access Verification
Password:
AP0022.558e.24bc>en
Password:
AP0022.558e.24bc#show lwapp ?
client LWAPP Client Information
ids LWAPP IDS Information
ip LWAPP IP configuration
mcast LWAPP Mcast Information
reap LWAPP REAP Information
rm LWAPP RM Information
AP0022.558e.24bc#show lwapp client config
AP0022.558e.24bc#
AP0022.558e.24bc#ping 3.45.47.143
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3.45.47.143, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
AP0022.558e.24bc# -
LAP 1240 won't join WLC across subnets
I am having a problem getting LAPs that are in other subnets to join our WLC. If I take the LAP and place it on the same VLAN/subnet as the WLC, it joins as expected. If I move it to another subnet, I get the following:
*Mar 1 00:00:13.065: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 08-Feb-08 17:24 by prod_rel_team
*Mar 1 00:00:13.119: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:13.519: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:14.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:14.536: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:14.545: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 24 seconds
*Mar 1 00:00:15.536: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:28.133: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.171: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:28.177: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:28.192: SSC Load Current Size crypto_mykey 120, offset 9389, Saved Size soap_cert_crypto_mykey 124
*Mar 1 00:00:28.390: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:28.892: Logging LWAPP message to 255.255.255.255.
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 192.168.115.75, mask 255.255.255.192, hostname AP0013.c3a7.bf97
Translating "CISCO-LWAPP-CONTROLLER.mydomain.here"...domain server (X.X.X.X) [OK]
%LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.mydomain.here
%LWAPP-3-CLIENTEVENTLOG: Controller address Y.Y.Y.Y obtained through DNS
%LWAPP-5-CHANGED: LWAPP changed state to JOIN
%LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
%LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller - 2169-WLC4402-1)
%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
%LWAPP-5-CHANGED: LWAPP changed state to DOWN
I have checked the WLC for any messages that look like crypto or other problems, but I don't see anything that stands out. Any suggestions or pointers would be greatfully accepted.%LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
Can you provide more information such as:
1. How many APs can the WLC4402 support and how many are currently joined?
2. What is your WLC's firmware?
3. Is there a possibility of a duplicate IP address in your network?
Troubleshoot a Lightweight Access Point Not Joining a Wireless LAN Controller
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml -
i am trying to troubleshoot a 2125 WLC alongside a 1252 access point. The access point is not joining and the y both
have the same software image. See logs below:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 5.2.193.0
RTOS Version..................................... 5.2.193.0
Bootloader Version............................... 4.0.191.0
Emergency Image Version.......................... 6.0.199.4
Build Type....................................... DATA + WPS
System Name...................................... Cisco_f4:f7:c0
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.828
IP Address....................................... 192.168.1.5
System Up Time................................... 6 days 2 hrs 42 mins 39 secs
System Timezone Location.........................
Current Boot License Level.......................
Next Boot License Level..........................
Configured Country............................... SI - Slovenia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
--More-- or (q)uit
Internal Temperature............................. +49 C
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C8:4C:75:F4:F7:C0
(Cisco Controller) >show network summary
RF-Network Name............................. law school
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Mode..................... Disable
Ethernet Broadcast Mode..................... Disable
AP Multicast Mode........................... Multicast Address : 0.0.0.0
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Disable
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Enable
Mgmt Via Dynamic Interface.................. Enable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
Kindly advice what is missing?
many thanksConsole into the AP and post the output to the following commands:
1. sh version;
2. sh ip interface brief -
Cisco 2702 not joining controller
Controller code vs. 7.6.120.0
From the controller:
(Cisco Controller) >debug capwap packet enable
Warning! Enabling this debug with large number of AP's connected, May flood console with message logs !!!.
Are you sure you want to continue? (y/N)y
(Cisco Controller) >*spamApTask3: Mar 05 13:38:13.317: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.317: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.317: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.317: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.317: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.317: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.317: Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.317: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.317: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.317: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.317: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.317: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.317: IE Length : 4
*spamApTask3: Mar 05 13:38:13.317: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.317: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.317: IE Length : 16
*spamApTask3: Mar 05 13:38:13.317: Rad Name :
*spamApTask3: Mar 05 13:38:13.317: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.317: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.317: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.317: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.318: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.318: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.318: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.318: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: Discovery Type : CAPWAP_DISCOVERY_TYPE_STATIC_CONFIG
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.318: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.318: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.318: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.318: IE Length : 4
*spamApTask3: Mar 05 13:38:13.318: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.318: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.318: IE Length : 16
*spamApTask3: Mar 05 13:38:13.318: Rad Name :
*spamApTask3: Mar 05 13:38:13.318: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.318: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.318: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.318: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.318: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.318: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.318: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.318: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.318: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.318: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.318: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.318: IE Length : 4
*spamApTask3: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.319: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.319:
*spamApTask3: Mar 05 13:38:13.319: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.319: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.319:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.319: IE Length : 16
*spamApTask3: Mar 05 13:38:13.319: Rad Name :
*spamApTask3: Mar 05 13:38:13.319: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.319: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.319: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.319: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask0: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:ec Received LWAPP DISCOVERY REQUEST to 6c:fa:89:da:ff:00 on port '1'
*spamApTask0: Mar 05 13:38:13.319: Start of Packet
*spamApTask0: Mar 05 13:38:13.319: Ethernet Source MAC (LRAD): 1C:6A:7A:BA:91:ED
*spamApTask0: Mar 05 13:38:13.319: Msg Type :
*spamApTask0: Mar 05 13:38:13.319: DISCOVERY_REQUEST
*spamApTask0: Mar 05 13:38:13.319: Msg Length : 70
*spamApTask0: Mar 05 13:38:13.319: Msg SeqNum : 0
*spamApTask0: Mar 05 13:38:13.319:
IE : UNKNOWN IE 58
*spamApTask0: Mar 05 13:38:13.319: IE Length : 1
*spamApTask0: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask0: Mar 05 13:38:13.319: 00000000: 01 .
*spamApTask0: Mar 05 13:38:13.319:
IE : UNKNOWN IE 50
*spamApTask0: Mar 05 13:38:13.319: IE Length : 46
*spamApTask0: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask0: Mar 05 13:38:13.319: 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 46 54 58 31 ............FTX1
00000010: 38 33 30 53 34 50 39 00 00 00 00 00 00 00 00 00 830S4P9.........
00000020: 00 00 00 00 01 01 00 0
*spamApTask0: Mar 05 13:38:13.319:
IE : RAD_PAYLOAD
*spamApTask0: Mar 05 13:38:13.319: IE Length : 14
*spamApTask0: Mar 05 13:38:13.319: H/W Version : 1
*spamApTask0: Mar 05 13:38:13.319: H/W Release : 0
*spamApTask0: Mar 05 13:38:13.319: H/W Maint : 0
*spamApTask0: Mar 05 13:38:13.319: H/W Build : 0
*spamApTask0: Mar 05 13:38:13.319: S/W Version : 7
*spamApTask0: Mar 05 13:38:13.319: S/W Release : 6
*spamApTask0: Mar 05 13:38:13.319: S/W Maint : 100
*spamApTask0: Mar 05 13:38:13.319: S/W Build : 0
*spamApTask0: Mar 05 13:38:13.319: Boot Version : 15
*spamApTask0: Mar 05 13:38:13.319: Boot Release : 2
*spamApTask0: Mar 05 13:38:13.319: Boot Maint : 4
*spamApTask0: Mar 05 13:38:13.319: Boot Build : 5
*spamApTask0: Mar 05 13:38:13.319: numSlots : 0
*spamApTask0: Mar 05 13:38:13.319: numFilledSlots : 0
*spamApTask0: Mar 05 13:38:13.319: End of Packet
*spamApTask0: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:ec Discarding discovery request in LWAPP from AP supporting CAPWAP
(Cisco Controller) >
From the AP:
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to 192.168.1.40
*Mar 5 19:48:53.007: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %SYS-3-MGDTIMER: Uninitialized timer, timer stop, timer = 3AFD270. -Process= "CAPWAP CLIENT", ipl= 0, pid= 74
-Traceback= 119AF80z 12A89C8z 12AA11Cz 16F512Cz 17645ECz 16FF088z 172810Cz 17299B4z 1720150z 1720228z 17204ECz 1717E50z 172F6A0z 173075Cz 1324C90z 1309B58z
*Mar 5 19:51:52.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 5 19:51:52.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
*Mar 5 19:51:52.999: LWAPP_CLIENT_EVENT: parse_lwapp_config: hostname AP1c6a.7aba.91ec
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: lwapp_mesh_enable_dhcp - allow DHCP
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: cdp run
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet0
cdp enable
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet0.1
cdp enable
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet1
cdp enable
end
*Mar 5 19:51:53.007: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 5 19:51:53.007: LWAPP_CLIENT_EVENT: parse_lwapp_config: line vty 0 15
transport input all
exit
end"test mesh mode local" is not a supported command on the AP. I tried to see if there was another syntax but couldn't find it.
AP1c6a.7aba.91ec#test mesh mode local
^
% Invalid input detected at '^' marker.
AP1c6a.7aba.91ec#test ?
GigabitEthernet GigabitEthernet IEEE 802.3z
Virtual-Template Virtual Template interface
aaa AAA Authentication, Authorization and Accounting
arp_retry Test ARP Retry
capwap CAPWAP test commands
cef Cisco Express Forwarding test command
cpuaccounting CPU Accounting test commands
cpurmi CPU RMI test commands
crypto Test crypto functions
dpaa DPAA test commands
dtls DTLS test commands
ecc ECC test commands
evtlog Evtlog test commands
ifs IFS TEST code
interfaces Network interfaces
iphc IPHC testing
opssl OPSSL Test
pb Test parameter block file system
persistent Persistent commands
process Create/kill test processes
rib RIB function test
rmi RMI test commands
rtcp Test RTCP SSM
save save load monitor snapshot
spanning-tree Spanning Tree Subsystem
ssm SSM test commands
tar test tar file system
topology Routing Topology test command
transport TACTIC - transport test commands
AP1c6a.7aba.91ec#test
From the AP:
AP1c6a.7aba.91ec#show version
Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 01-May-14 22:18 by prod_rel_team
ROM: Bootstrap program is C2700 boot loader
BOOTLDR: C2700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.2(4)JB5m, RELEASE SOFTWARE (fc2)
AP1c6a.7aba.91ec uptime is 46 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP2702I-A-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FTX1830S4P9
PowerPC CPU at 800MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.100.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 1C:6A:7A:BA:91:EC
Part Number : 73-15824-03
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC182876JM
Top Assembly Part Number : 800-41174-01
Top Assembly Serial Number : FTX1830S4P9
Top Revision Number : A0
Product/Model Number : AIR-CAP2702I-A-K9
Configuration register is 0xF
AP1c6a.7aba.91ec#
From the WLC:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... xxxxxxx_lab
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.1.40
Last Reset....................................... Software reset
System Up Time................................... 0 days 1 hrs 0 mins 6 secs
System Timezone Location......................... (GMT -6:00) Central Time (US and Canada)
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +41 C
Fan Status....................................... 4700 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 6C:FA:89:DA:FF:00
Maximum number of APs supported.................. 5
(Cisco Controller) > -
I upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
The country codes etc were all fine so I do not understand what was going on.
Any ideas?
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discovery Request from 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discovery Response sent to 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Discovery Request from 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Discovery Response sent to 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discovery Request from 10.0.1.232:20023
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discovery Response sent to 10.0.1.232:20023
*spamApTask0: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Discovery Request from 10.0.1.232:20023
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Discovery Response sent to 10.0.1.232:20023
*spamApTask4: Jun 26 16:07:46.516: 00:3a:99:db:fa:10 DTLS connection not found, creating new connection for 10:0:0:101 (55079) 10:0:1:45 (5246)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:101/55079)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 No entry exists for AP (10:0:0:101/55079)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 No entry exists in database
*spamApTask4: Jun 26 16:07:47.759: 00:3a:99:db:fa:a0 Discovery Request from 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.759: 00:3a:99:db:fa:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Response sent to 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Request from 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Response sent to 10.0.0.184:55084
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discovery Request from 10.0.1.239:20032
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discovery Response sent to 10.0.1.239:20032
*spamApTask0: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Discovery Request from 10.0.1.239:20032
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Discovery Response sent to 10.0.1.239:20032
*spamApTask1: Jun 26 16:07:52.222: 00:13:c3:e1:4d:80 Discovery Request from 10.0.1.230:20027
*spamApTask1: Jun 26 16:07:52.222: 00:13:c3:e1:4d:80 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discovery Response sent to 10.0.1.230:20027
*spamApTask0: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discovery Request from 10.0.1.230:20027
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.224: 00:13:c3:e1:4d:80 Discovery Response sent to 10.0.1.230:20027
*spamApTask5: Jun 26 16:07:52.267: 00:3a:99:da:c7:70 DTLS connection not found, creating new connection for 10:0:0:181 (34152) 10:0:1:45 (5246)
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discovery Request from 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discovery Response sent to 10.0.0.182:55099
*spamApTask0: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Discovery Request from 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Discovery Response sent to 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.306: 00:3a:99:db:f2:40 DTLS connection not found, creating new connection for 10:0:0:100 (55069) 10:0:1:45 (5246)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:181/34152)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 No entry exists for AP (10:0:0:181/34152)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 No entry exists in database
*spamApTask1: Jun 26 16:07:52.501: 00:3a:99:db:f2:40 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:100/55069)
*spamApTask1: Jun 26 16:07:52.502: 00:3a:99:db:f2:40 No entry exists for AP (10:0:0:100/55069)
*spamApTask1: Jun 26 16:07:52.502: 00:3a:99:db:f2:40 No entry exists in databaseSomething "weird" is on the newest 7.0.X. Here's my situation:
1. It doesn't happen to all new APs. When I mean "new", I mean out from a box including APs from RMA.
2. I've seen this in 1240, 1250, 1140. Haven't seen it on a 3500.
3. Here's how it goes ... When the AP, fresh from a box, connects to the networks, sees the WLC/WiSM and downloads the full IOS (OK so far). After the reboot the AP in question loads the new IOS and shows up in the WLC/WiSM. When I check CDP neighbors, NOTHING. What the ... ?
4. Go to the switch and do command "sh cdp neighbor" and what do I get? NOTHING.
5. Check PoE and show that it's IEEE.
For unknown reason, APs in this "trance" shuts off the CDP. I currently have a Cisco TAC Case trying to iron out this "feature". Doesn't appear on the 7.0.96.0 but happens to the newer one. -
1140 AP not joining controller
I have 3 AP's setup on my network and each port is configured the same exact way on the switches. One AP joined the controller fine but the other two are not joning it. They get the IP address but that is about it. When I go and check for the statistics on the WLC it tells me that they are not joined. Here is what the DEBUG shows:
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc CAPWAP Control Msg Received from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc packet received of length 97 from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Msg Type = 1 Capwap state = 0
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Discovery Request from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 20
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 68
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 40 msgEleType = 39
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 24
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 41
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 19
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 44
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 14
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc msgEleLength = 10 msgEleType = 37
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Vendor specific payload from AP C4:71:FE:8F:DA:DC validated
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Total msgEleLen = 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 12, joined Aps =1
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 1. 1 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 2. 232 3
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 3. 1 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 4. 12 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: AC Descriptor message element len = 40
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc acName = WLCNAME
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp:AC Name message element length = 56
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: WTP Radio Information msg length = 65
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: CAPWAP Control IPV4 Address len = 85
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: CAPWAP Control IPV6 Address len = 107
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: Mwar type payload len = 118
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: Time sync payload len = 133
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery Response sent to 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc WTP already released
Note: I have one "management interface" configured on 10.230.129.xxx network" Then I created two "AP Manager interfaces on the 10.230.129.xxx network and enabled dynamic AP Management on them".Ok, right, thats because whenever you type ANY number it TAGs the packets with that vlan id. 0 leaves the traffic untagged.
So even if it that IP belongs to vlan 10, if the port is as native (untagged) then on the WLC side should be 0
Thats how it was designed. -
hi All,
I have a scenario where my 2602E is not joining a controller in US. AP is in Netherlands.
AP: AIR-CAP2602E-E-K9
Logs on WLC 5508:
*spamApTask4: Jan 29 10:26:37.398: 18:9c:5d:9b:4d:00 Bridge AP can not join MultiCountry Controller: Bridge mode AP 10.130.90.11:63313 cannot be supported on Multi Country Controll
*spamApTask4: Jan 29 10:26:37.406: 18:9c:5d:9b:4d:00 State machine handler: Failed to process msg type = 3 state = 0 from 10.130.90.11:63313
is there a way i can change the bridge mode from this AP to normal or Local so that it can be useD?
Any help will be great.
thanks
Roycecheck the following.
-
1130AG not joining controller - FAILED CRYPTO INIT
I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. The error I'm getting is:
*Mar 1 00:00:29.584: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:29.585: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no certs in the SSC Private File
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not start PKI session
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Rebooting
*Mar 1 00:00:29.663: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)
*Mar 1 00:00:29.663: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:29.664: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNXmodem file system is available.
I found some details here: http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml, but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
Thanks!While that did help me potentially debug the AP, it seems the AP can not/is not reaching the WLC. Debugs on the WLC show other APs talking to it, but the only signature I'm picking up on the WLC from this AP is:
*Aug 08 20:34:36.376: 00:13:5f:fb:b4:f0 Echo Request from 10.50.0.25:44194
*Aug 08 20:34:36.376: 00:13:5f:fb:b4:f0 Echo Response sent to 10.50.0.25:44194
And from the AP itself:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:06.475: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event (contains, 1024 messages)
*Mar 1 00:00:08.523: %LINK-3-UPDOWN: Interface FastEthernet0, changed state up
*Mar 1 00:00:08.548: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.4(21a)JA2, RASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:17 by prod_rel_team
*Mar 1 00:00:09.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthet0, changed state to down
*Mar 1 00:00:17.310: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:20.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTRER
Writing out the event log to nvram...
*Mar 1 00:00:29.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTLER
*Mar 1 00:00:29.592: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no ce in the SSC Private File
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not st PKI session
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Roting
*Mar 1 00:00:29.666: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON led, because size left in ROMMON (4294967295), size needed (29), error code (
*Mar 1 00:00:29.667: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reloaeason: FAILED CRYPTO INIT.
*Mar 1 00:00:29.667: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
Is my only option at this point reverting back to a standalone image, then going back to a LW one?
Thanks again,
-Ryan -
1142 AP will not join Controller through a D-Link POE Switch
This is fun.
I'm trying to use 1142 APs with a 2504 Wireless Controller through a D-Link 48PT GBIT XSTACK SWITCH (DLI-DGS-3120-48PC/SI). (I know. Shame on me. Couldn't help it.)
At any rate, the 1142 AP joins with the wireless controller ONLY when I attach it directly to the controller. When connected directly to the controller the AP functions normally and all is well.
When I attach it through the D-Link switch, the AP flashs green several times, indicating that it can't find the controller.
I suspect that there's some setting on the D-Link switch that's preventing the AP from seeing the controller, but I have no idea what that might be.
Any suggestions would be helpful. Thanks.leolahoo,
Thanks for responding. I appreciate it very much.
I checked the management interface in the GUI on the controller (which is set to an internal IP address 10.1.1.20), but after doing that I am not sure what you mean by "the link should be untagged."
UPDATE: I just saw on the main interface screen that the VLAN identifier for the management interface is marked as "UNTAGGED."
Also note the ping test results I sent to Ron above.
Any idea as to where to proceed from here?
Thanks very much.
Ken
Maybe you are looking for
-
Crash Minidump/Restart at Shutdown inside login, but Shutdown before any user logins is ok.
Crash Minidump/Restart at Shutdown inside login, but Shutdown is ok before any user logins. Just Started. Windows says error report says to update Video Driver, But HP 235558hc has current valid driver. 4 Year Old HP Pavillion Quad with Windows V
-
I need some basic conceptual help with QT! I have used QT Player since QT started, but I have always used it just to play whatever simply double-clicks open in it. I have QT Pro, so I know QT can do more. However, I don't understand some basic things
-
Ive tried followinf a number of posts on using the 2 step verification method- none of it works. Please I need help with this, thanks.
-
File not visible in Finder until spotlight search
Wierd. I have been working on a Photoshop project all week. The project uses several jpg files and I have saved the psd's in the same folder. Toady when starting up PS, none of the psd files were in the folder - everything else for the project was. B
-
Reg different kinds of select stmts
Hi All, Hope all are doing gud, cud any tell me different kinds of select stmts ???? regards, abc xyz