3750-E - hardware not supported by firmware

Hello, I have got new 3750
e-series which has universal image installed on it. I need to put this
switch in stackwise with non-e-series 3750. The problem is that
non-e-series are running IP BASE IOS and I wanted to put the same IOS
on 3750 e-series. But it gives me the following message when I try to
boot the switch with c3750-ipbase-mz.122-35.SE5.bin image.
Error: hardware not supported by firmware.
Try loading newer software instead.
System Resetting...
Thank you!
Hi,
Catalyst 3750-E switches running Cisco IOS Release 12.2(35)SE2 are compatible with Catalyst*3750 switches and Cisco EtherSwitch service modules running Cisco IOS Release*12.2(35)SE. Catalyst 3750-E switches, Catalyst 3750 switches, and Cisco EtherSwitch service modules can be in the same switch stack. In this switch stack, we recommend that the Catalyst*3750-E switch be the stack master.
Check out the below link for more information
http://www.cisco.com/en/US/docs/switches/lan/catalyst3750e_3560e/software/release/12.2_35_se2/release/notes/OL9778.html
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

Similar Messages

Bluetooth Headset Hardware not supported

I have a Kensington USB dongle and I pasted the ASP info below. I can use it for pretty much everything except for using my headset. Does any one know of a way to enable this?
I can't imagine why Apple would only support headsets on their bluetooth hardware. I read in this forum that a D-link dongle is supported, does it have any specific features that my Kensington dongle does not list in the Apple system profiler?
Apple Bluetooth Software Version: 1.7.8f2
Hardware Settings:
tower:
Address: 00-0c-55-f8-47-c6
Manufacturer: Broadcom
Firmware Version: 2.0 (2.26981)
Bluetooth Power: On
Discoverable: Yes
HCI Version: 2 ($2)
HCI Revision: 0 ($0)
LMP Version: 2 ($2)
LMP Subversion: 26981 ($6965)
Device Type (Major): Computer
Device Type (Complete): Desktop Computer
Composite Class Of Device: 1057028 ($102104)
Device Class (Major): 1 ($1)
Device Class (Minor): 1 ($1)
Service Class: 129 ($81)
Requires Authentication: No
Services:
Bluetooth File Transfer:
Folder other devices can browse: ~/Public
Requires Authentication: No
State: Enabled
Bluetooth File Exchange:
Folder for accepted items: ~/Documents
Requires Authentication: Yes
When other items are accepted: Ask
When PIM items are accepted: Ask
When receiving items: Prompt for each file
State: Enabled
Devices (Paired, Favorites, etc):
Name:
Address: 00-15-b9-8b-d6-57
Type: Cellular Phone
Services: HFP Gateway, Dialup Networking, Object Exchange, File Transfer, WBTEXT, HSP Gateway
Paired: Yes
Favorite: Yes
Connected: No
Incoming Serial Ports:
Serial Port 1:
Name: Bluetooth-PDA-Sync
RFCOMM Channel: 3
Requires Authentication: Yes
Serial Port 2:
Name: SerialPort-1
RFCOMM Channel: 1
Requires Authentication: Yes
Outgoing Serial Ports:
Serial Port 1:
Address: 00-15-B9-8B-D6-57
Name: Bluetooth-Modem
RFCOMM Channel: 4
Requires Authentication: No
Serial Port 2:
Address: 00-15-B9-8B-D6-57
Name: SPH-A900-DialupNetworki-1
RFCOMM Channel: 4
Requires Authentication: No

Dlink is STILL the only officially supported usb BT dongle and I have one and it works great if you only want 10m radius.
I bought a Targus ACB20 (also known as ACB20us) because my GF wanted BT connectivity for her headset on her eMac. I realised AFTER that headsets were not supported for the Broadcom Chipset in this device.
I found the answer here -> http://cbri.umn.edu/~kunau/?p=18
this guy found a belkin patch for his device that allows broadcom chipset dongles to use headsets (YAY).
here is the direct dl link for the file -> http://ccgb.umn.edu/~kunau/wp-content/uploads/2006/06/BelkinF8T012v-OSXdriver.zip
This works fine with my targus dongle and another Anycom one I have (both 100m).
Hope this works for you.
Kez

3750 and Netflow not supported (alternatives ??)

              ISP
               |
|             3750            | -------- |           3745              |
- - - - - - - - - - - - - - - - -    span   - - - - - - - - - - - - - - - -
               |
          Internal
I have an ISP facing 3750 switch running BGP. I want to collect Netflow statistics for this IP traffic.
I know that Netflow is not supported on the 3750 switch.
I know Lancope offer a Flow sensor for capturing data on a span port and turning this into netflow stats.
http://netflowninjas.typepad.com/blog/2009/12/stealthwatch-510-highlight-flowsensor-ae-features-and-benefits.html
I need a temporary solution and I have a spare 3745 router which supports netflow. I cant put this router
in series because it may be a bottleneck on a 20Mbps ISP connection.
Is there a way of feeding span traffic from the 3750 into a 3745 and seeing if it is able to generate the netflow stats.
I have tried this using only one interface and it does not work. Do I need to span both internal and external interfaces.
Does the IP traffic arriving at the 3745 have to cross two interfaces to generate neflow stats.
http://www.netflowanalysis.com/How%20does%20NetFlow%20Work.html
Any ideas ?

Hello,
there are only 3 solutions.
1. Small router inline. I suppose that it will OK for 20Mbps line.
2. Use SPAN and some probe (software or hardware based).
3. Optical TAP and probe.
Our company is offering software or hardware based probes.
(see http://www.caligare.com/product/flowmon/ for more information)
You can also use the Lancope or nProbe (free) of course.
Kind regards,
Jan Nejman
Caligare, co.
http://www.caligare.com/

PPCG4 hardware not supported

I've got a PPCG4 FW800 1.25GHz DP & 1.25GB RAM OSX 10.4.6 and ProKit 3.1 framework. When I try to launch Aperture 1.0 it tells me that my hardware isn't supported and quits.
The specs state that the app supports "1.25GHz or faster PowerPC G4 processor"
Any ideas appreciated?
PPC G4 FW800 1.25GHz DP 1.25GB RAM ATI Radeon 9000 Pro Mac OS X (10.4.6)

Correct, the machine is not adequate. IMO Apple's use of the term "unsupported by Aperture" is unfortunate, because the semantic implication is that Aperture does not "support" a particular box. As a consequence dozens of folks have posted wanting to know when Aperture will be modified to "support" their boxes; as if the engineers just need to write some code to facilitate each hardware configuration (like printer drivers; or enablers that fit the OS to specific boxes).
IMO it would be more clear if Apple just identified boxes like yours (and my tower) as "this hardware is not powerful enough to run Aperture."
Although some speed improvements on the software side (both OS and app versions) can usually be made, the basic issue is that it takes strong hardware to drive heavy graphics applications. E.g. the best 2005 Powerbooks were the first time Photoshop was really usable on any Powerbook, and that just "adequate."
Aperture (designed to handle batches of hundreds of RAW image files) requires strong hardware including the CPU, RAM, hard drives, etc. (and especially the GPU, as noted). In the long term, app designers always take advantage of the stronger power of newer boxes, so we should plan - like Photoshop users have learned through 9 versions - on buying the high end of Macs at any given point in time if we want to have adequate throughput power to drive future versions of Aperture, Photoshop, etc.
Note that my expectation is that by 2007-2008 heavy graphics apps will be wanting more RAM and strong GPUs. Buyers of boxes limited to 2 GB max RAM and/or lesser graphics should expect performance to be limited accordingly. E.g. Photoshop CS2 boxes already perform best when configured with 6-8 GB RAM.
-Allen Wicks
Early 2005 1.67 GB G4 PB, Radeon 9700, 128 MB VRAM, 1.5 GB RAM Mac OS X (10.4.6) D2x, DP G4

Audio Hardware not supported by IDT Drivers

Hi,
I accidentally uninstalled my IDT Audio Drivers. Now my audio does not work at all. When I go to install the drivers suggested by the HP Software Support section, the drivers display this message during installation: "The hardware detected is not supported by this IDT software package. The install will be aborted."
HP Pavilion g6 - 1a21ca Notebook PC
Product Number: LV993UA
Windows 7 (64-bit)

Hi,
The first option I'd suggest trying is to run Windows System Restore.
If you have Norton Internet Security installed, you will need to disable Norton Tamper Protection as shown on the link below.
Norton Tamper Protection.
Once you've done this, shut down the notebook. Windows System Restore is usually best run in Safe Mode. Tap away at f8 as you start the notebook to enter Windows Recovery Console. Use the arrow keys to select Safe Mode and hit enter. When this has loaded, from the Start Menu, click All Programs, click Accessories, click System Tools and launch System Restore. Pick a restore point at least 24 hours before the original audio driver was deleted and then proceed with the restore process. When complete, Windows will reboot as normal.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Hardware not supporting old kernels!!

Yesterday I bought M/board Asus P5V800 + Intel LGA775 Pentium 4 CPU
http://www.asus.com/products4.aspx?l1=3 … odelmenu=1
Either the new CPU (socket LGA775) or the M/borad, doesn't support Kernel-2.6.11 (my custom kernel) but the latest 2.6.16. I also tried Archie Live CD (2.6.x) and Knoppix 3.6 (2.4.x), doesn't work. In Knoppix booting freezes asking for "south bridge dma", in Archie no X support, and in HD no X and LAN support.
In Windows, doesn't support Win 98. Runs but cannot install some of the board sources. Drive install CD for 2000 and XP only.
<b>For my information, is this a common restriction of LGA775?</b>
Note: End of the day I sold the hardwares and upgraded my old Celeron (socket 478) to Pentium. Pentium 4 with Celeron doesn't work well managing heavy multitask work. Compiling apps and at the same running X apps freezing the machine.

Windows has shoddy driver support until 2000/XP. I also found this out first hand trying to install Windows ME with what should be considered very old compatible drivers. That's we me pops runs latest standard kernel with Arch Linux now. It loves the hardware (not literally), but me pops loves the Arch.
So, it goes, backwards compatible is easy, forward compatible depends on too many things like driver unification and just how shoddy the OS is (MS). I'm just amazed at how much of a mule the OS can be when it has trouble recognizing hardware. so I had this thread: "I would rather spend a week causually installing/configuring arch than the rest of my life installing Windows ME."...or something to that effect.

Iphone 3s hardware not supported by Windows xp

I plugged in my wife's iphone 3gs phone to update in Itunes. I got a message from Windows that the hardware driver was not recognized. I was able to get in Itunes and record my device. It started updating. I came back to an error message and now Windows refuses to recognize the iphone when I plug it in and Itunes will not pull up my phone as a recognized device either. I see the iphone in backup but cannot restore it. All my phone shows is a picture of the USB cord to connect to Itunes. How do I get Windows XP to accept the Iphone hardware? Please help me restore this iphone. Thank you,

Remove and reinstall iTunes. See: http://support.apple.com/kb/HT1925
Disable your antivirus and firewall before updating or restoring the phone.

Hardware not Supporting Premiere Pro CS5.5 (and after effects)

Hardware: 1st generation Macbook Pro 2.0Ghz Intel Core Duo processor, 2g (maximum ) ram, 500gb hybrid SSD/7200 hard drive. Mac OS leaopard 6.6
I bought the master collection recently which includes premiere and after effects CS5.5. Pre sales I was advised by adobe that ALL macbook pros will run all these products (by an adobe customer services Advisor)
I can't load them because (as I have now learnt) that the core duo processor only supports 32 bit- I phoned technical support, many times since 15th July and was repeatedly told that ALL macbook pros can run them, it was just a case of changing my OS to 64 bit. Apple are clear that this is not the case.
Eventually I was referred to a tier 2 advisor, who asked me which processor type, and finally said it is clear that I need earlier versions to run on this and I would be contacted by email to provide a earlier 32 bit version of these 2 programs (as is supplied to windows 32 bit users). This was 2 weeks ago and I have had no response, I have phoned several times and some advisors try to start the whole process again and insisting that I should be able to install these.
Today an advisor has told me that they have checked the notes and the tier 2 advisor has advised I "need to upgrade my hardware" (ie buy a new mac !!!)
No-one will give me any phone numbers of a tier 2 advisor to discuss this or complain about it. Nor an email address.
First i want to request that adobe, having misled me, should give me earlier copies. Especially as this has already been agreed. Secondly I want to complain about the huge amount of time wasted and how I have been fobbed off.
Apologies if this is not the exact forum space for it but I cannot find the issue on FAQ so I would be very grateful if anyone can put me in touch with the right person, or if any of the moderators would know.
Michael Bannon

8/17/11
Case #0182568779: case update: 0206296078
Withdrawn
8/16/11
Case #0206296078: Download Link
Withdrawn
8/2/11
Case #0182523822: Unable to install After effects
Withdrawn
8/2/11
Case #0182527143: Escalated case :182523822, 0206296078
Withdrawn
8/1/11
Case #0182524205: installation issue
Withdrawn
Many thanks: these were the case numbers- these have all bee witthdrawn despite the fact none of them has yet provided the solution promised by the tier 2 advisor.
Michael

Graphics Hardware Not Supported

Just installed CS6 and wish to use the 3d option to create some text. However I get the window popup telling me that my graphics hardware is not officially supported for 3D.
I have a Nvidia GTX Titan which has 6gb vram.

mchief111
Could you please post your system info listed in Photoshop's Help > System Info dialog box?
Click Copy, then paste it in a response here.
That will help us determine further what's going on.
Allow me echo the interest in making sure the latest nvidia driver is applied
http://www.nvidia.com/Download/indexsg.aspx?lang=en-us
Your video card: NVS (notebooks) -> NVS 4200M
Also give the forcing Photoshop.exe to use the nVidia video card in the NVIDIA Control Panel
Right click desktop -> NVIDIA Control Panel
Manage 3d Settings category -> Program Settings tab
under the 1. "Select a program to customize" drop down menu: select Photoshop.exe
for 2. Select the preferred graphics processor for this program: select High-performance NVIDIA processor
Click the Apply button that appears in the lower right.
You will need to reset Photoshop's preferences as well for it to look for your video driver changes.
To do this, immediately after starting Photoshop.exe press and hold Ctrl+Shift+Alt
Click Yes to reset the Photohsop Settings file.
Let us know how it goes from there.

What does the "graphics hardware not supported" error mean?

Photoshop detected graphics hardware that is not officially supported. If you experience problems, please uncheck the Use Graphics Processor checkbox in the Performance panel of the Preferences dialog.
My system:
Mac Pro
2 x 2,66 GHz Dual-Core Intel Xeon
10 GB 667 MHz DDR2 FB-DIMM
ATI Radeon X1900 XT 512 MB
Mac OS X Lion 10.7.3 (11D50b)

It looks like you have a video card that is not officially supported in CS6.
Here is a link to the FAQ on GPU features and supported cards:
http://forums.adobe.com/message/4289204
Check out the instructions on turning off OpenGL. You won't be able to access certain features that use the GPU, but you will no longer see the error message.

Server hardware not supported

I added in some b200 M4 blades into the UCs chassis and tried to reack the slot.
but got this error. I am running ucsm 2.1(3a)
any idea?

Hi Tony,
This message is expected as the B200M4 requires a minimum firmware of 2.2(3a) see below. To resolve this issue you need to upgrade the UCS infrastructure firmware to at least version 2.2(3a)
Table 4 Internal Dependencies
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/release/notes/ucs_2_2_rn.html#pgfId-226104
Let me know if this helps

I am getting the photoshop has detected graphics hardware not supported for 3d...without 512 vRam. I have enough and yet it still gives me the error. I have ATI Radeon HD 2600 Pro 256 MB installed and can't find any updates on adobe? What gives?

Where do I find the update?

Well, which school did you attend to justify your crooked math? When I was at school 256 was less than 512 or exactly half of 512... This simply won't work and nobody can fix it for you. Your graphics hardware is simply completely inadequate, considering that it is like 7 years or so old to begin with.
Mylenium

Apple USB Modem Not Supported in Snow Leopard Running 64-bit Kernel Mode

Has anyone been able to get the Apple USB Modem to work with Snow Leopard (SL) when running SL in 64-bit kernel mode? I get an error saying hardware not supported.

I would suggest you take this question up in the MacBook Pro forum or perhaps the Snow Leopard forum. This forum is for question about older, Pre-G3 Apple hardware and so not the forum where you'll be most likely to get a quick and applicable response.
Regards.

I want update firmware 2.9 but apear this message "This software is not supported on your system."

hi
I want update firmware .details my system is
Hardware Overview:
Model Name:          MacBook Pro
Model Identifier:          MacBookPro9,2
Processor Name:          Intel Core i5
Processor Speed:          2.5 GHz
Number of Processors:          1
Total Number of Cores:          2
L2 Cache (per Core):          256 KB
L3 Cache:          3 MB
Memory:          4 GB
Boot ROM Version:          MBP91.00D3.B08
SMC Version (system):          2.2f38
Serial Number (system):          C1MHQC17DTY3
Hardware UUID:          EF0C6F81-20AD-50FA-9DD5-C8E084DF8E8C
Sudden Motion Sensor:
State:          Enabled
but when install the last update MacBookProEFIUpdate2.9 i got error like this
"This software is not supported on your system."
please help me thanks

OK, so the firmware is the same as mine, and yet Apple Support offered this EFI and SMC update packages, which should give a message that our computers are updated.
However, the update packages fail to run.
Did Apple neglect to give the correct update for the mid-2012 issue of MacBook Pro 13-inch? I have the i7 Intel processor, instead of the i5, and I was sold this unit as having two processors, but the System info only lists a single processor.
Is one of the problems with Intel-based MacBook Pro units that the integration wasn't without bugs that cause processor hang when running the OS Lion, even with updates to 10.7.5?
Shouldn't the EFI and SMC updaters run on these machines as stated in the Apple Support article?
What will Apple do for these customers?

Ive been trying to update my macbook pro 8,2 firmware from the apple website but first the smc update gives me an error saying that my software does not support that update and belive me i checked and iam downloading the correct one

so basically i was wanting to update my smc firmware and the EFI Boot ROM version but for the EFI Boot Rom when i click on it says page no found and for the smc firmware, when i do download it says that the my software does not support it, even though it is completely compatible, i checked the system requirements given by the page.
iam trying to do this because i have issues with the chargin, it keeps giving me a "not charging" messege.
Help please...

SadisticIron wrote:
i just baught my first iphone and it is a jalbroken
Buzz! Thank you for playing!
Discussing jailbroken devices is forbidden here by the Terms of Service.
You can not get help here.

3750-E - hardware not supported by firmware

Similar Messages

Maybe you are looking for