3750 metro switch does not support Dot1q??

Folks,
I have a 3750 metro series switch and i am trying to use it to do inter vlan routing. I do not see an option for "encapsulation dot1q" under sub interface?? why is it not supported??
Thanks

Navin,
This question has been answered under "Network Infrastructure".
Josef.

Similar Messages

  • 3750 metro series switch does not support dot1q trunking?

    Folks,
    I have a 3750 metro series switch and i am trying to use it to do inter vlan routing. I do not see an option for "encapsulation dot1q" under sub interface?? why is it not supported??
    Thanks

    Narvin,
    if you want inter-vlan routing, the interface Vlan nn itself specify vlan.I think you confuse with router subinterface where you must specify what Vlan a subinterface must use ( and encaps type ). Encaps type ( dot1q or ISL ) is used at trunk level, and whatever trunk use you can do intervlan routing using vlan interface.
    maurizio

  • 3750 Metro series do not dot1q trunking??

    Folks,
    I have a 3750 metro series switch and i am trying to use it to do inter vlan routing. I do not see an option for "encapsulation dot1q" under sub interface?? why is it not supported??
    Thanks

    Navin,
    The 3750 Metro series switch does not support Layer 3 trunks; you cannot configure subinterfaces or use the encapsulation keyword on Layer 3 interfaces. The switch does support Layer 2 trunks and Layer 3 VLAN interfaces, which provide equivalent capabilities.
    For more information, see the note under Table 12-5 on this page: http://www.cisco.com/en/US/products/hw/switches/ps5532/products_configuration_guide_chapter09186a00803960dc.html#wp1326724.
    Cheers,
    Josef.

  • Cat0-3750 upgrade. Error: system number 1 does not support the same feature

    I am trying to upgrade or rather downgrade from ipadvservices (inadvertently upgraded to) to ipservices on a stack of Cat-3750s, but I get the following error message:
    Ios Image File Size: 0x00877A00
    Total Image File Size: 0x00B04200
    Minimum Dram required: 0x08000000
    Image Suffix: ipservicesk9-122-37.SE1
    Image Directory: c3750-ipservicesk9-mz.122-37.SE1
    Image Name: c3750-ipservicesk9-mz.122-37.SE1.bin
    Image Feature: IP|LAYER_3|PLUS|SSH|3DES|MIN_DRAM_MEG=128
    Error: The image in the archive which would be used to upgrade
    Error: system number 1 does not support the same feature set.
    Any ideas?
    Chris

    I was having the same issue even with entering the following:
    archive download-sw /overwrite /allow-feature-upgrade tftp://172.18.108.26/c3kx-sm10g-tar.150-2.SE7.tar
    I noticed the image which was running on the switch was correct without the ".bin" at the end:
    3560#sh ver | i image
    System image file is "flash:c3560e-universalk9-mz.150-2.SE7"
    I uploaded a fresh IOS image from CCO and made sure the image name had ".bin" at the end. Seems trivial except the error is produced through a sanity check. See below (please excuse the extra unplugging in the output):
    3560#sh ver | i image
    System image file is "flash:c3560e-universalk9-mz.150-2.SE7.bin"
    3560#$de tftp://172.18.108.26/c3kx-sm10g-tar.150-2.SE7.tar
    Loading c3kx-sm10g-tar.150-2.SE7.tar from 172.18.108.26 (via Vlan1): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!                             !!!!!!!!!
    Mar 30 01:33:35.480: %USBFLASH-5-CHANGE: usbflash0 has been removed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    Mar 30 01:34:15.636: %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding!!!!!!!!!!!
    [OK - 24893440 bytes]
    Loading c3kx-sm10g-tar.150-2.SE7.tar from 172.18.108.26 (via Vlan1): !!!
    Mar 30 01:34:35.593: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 2 removed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!                             !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    examining image...
    extracting info (100 bytes)
    extracting c3kx-sm10g-mz.150-2.SE7/info (499 bytes)
    extracting info (100 bytes)
    System Type:             0x00010002
      Ios Image File Size:   0x017BDA00
      Total Image File Size: 0x017BDA00
      Minimum Dram required: 0x08000000
      Image Suffix:          sm10g-150-2.SE7
      Image Directory:       c3kx-sm10g-mz.150-2.SE7
      Image Name:            c3kx-sm10g-mz.150-2.SE7.bin
      Image Feature:         IP|LAYER_3|MIN_DRAM_MEG=128
      FRU Module Version:    03.00.78
    Updating FRU Module on switch 1...
    Updating FRU FPGA image...
    FPGA image update complete.
    All software images installed.
    Worked for me, hope this helps.

  • Cisco DCNM 6.2 does not support most of the switches in my network

    Hi All,
    I have just installed Cisco DCNM 6.2. I have run a discovery using SNMP v1 my core switch which is a 3750G stack. DCNM discovers all my switches but does not support the 2960 and 3750 switches. The only switches I can select to manage and are supported are a 4510 and 3550. I have also run another discovery using SNMPv3 on a different core switch (Nexus 3K) at one of our remote sites. DCNM found all the other 2960s in that network but I can only select the two Nexus switches in the core to manage. What do I need to do to be able to manage all my switches switch?
    Thank you in advance.

    Hello,
    DCNM is meant for data centre network management and as such only supports the MDS, Nexus and the 6500 series switches, see the RN under supported Cisco platforms and software:
    http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/6_x/dcnm/release/notes/dcnm_6_2_5a_relnotes.html#pgfId-314209
    For the discovery issue DCNM should 'see' the other devices so you need to have a look at your SNMP and CDP (used for neighbour discovery on a per hop basis) settings on each of the devices.
    For an software package to manage LAN/WAN environments you really need to be looking at Cisco Prime LMS.
    We are going through the same problem, it would be nice to be able to manage the DC and LAN from DCNM.
    Regards
    Daniel Hunter

  • WARNING: Any laptop that comes with an *automatic* switching Radeon 6770m does not support OpenGL.

    WARNING: HP has falsely advertised their dv6 and dv7 line. Any laptop that comes with an *automatic* switching Radeon 6770m does not support OpenGL and various other software. OpenGL games, Adobe CS Suit, and Design programs such as CAD or MatLab are incompatible with this laptop!

    According to this post the 6670m does fully support open GL 4.1
    http://forum.notebookreview.com/hp-pavilion-notebooks/583203-dv6t-7-switchable-graphics-76.html#post...
    And AMD says it does also
    http://www.amd.com/us/products/notebook/graphics/amd-radeon-6000m/amd-radeon-6700m-6600m/Pages/amd-r...

  • Is there an easy way to switch from Entourage (MS Office email) to Apple email?  The new MS Office does not support Entourage.

    I am looking for a way to shift from Entourage (MS Office email) to the Apple system for email?  The new MS Office does not support Entourage.

    Philip if you can't find your answer in this forum try the Snow Leopard forum, Mail is considered part of OS X so you may have luck there.
    Also you also may want ot be more specific when posting. I'm assuming because you only mention Mail all you are interested in is switching to Mail or did you have more in mind?

  • My av adaptor does not work. Tried to plug my ipad into my samsung hd tv and ipad said it does not support that accessory...help

    My av adaptor does not work. Tried to plug my ipad into my samsung hd tv and ipad said it does not support that accessory...help

    What ipad,  which model samsung?  Are you attempting HDMI, VGA, or an RGB connection.  Ipad 2 supports mirroring into an HDMI at an output of 1080.  Ipad 1 is limited to only a few apps capable of the output, such as Youtube.
    page64,65 of the latest ipad manual has more details.
    Samsungs are good and should switch with the input - but sometimes you will have to select from the menu manually.
    If in doubt, contact the customer support at samsung UK.
    Also check - Settings/Video, that you have it enabled for Home Sharing.  Apple Id  which will be your .me.com  email plus your apple ID password.  I am not too sure about  this as I cannot remember the exact order I set things up in - but page 89 of the manual references Home Sharing for sharing ipad/itunes content on a home pc/mac - so I would think it applies to content relayed to a tv or monitor too.

  • Pages 5.0 version does not support pictures in header

    I recently installed new soft OS X Maverick and along with this also renewed soft for Numbers, Pages, Keynote, and some more apps.
    Pages version 5.0 does not support its earlier version pre-set headers and footers. All the logos (picture files) I had inserted for my company template in the header are gone and I cannot re-enter them either. Does anyone can give e a hint on how to use picture files in Pages version 5.0 templates?
    This is first time in 2+ years that I prefer to use MsWord over Pages on my Mac, which is a pity.
    *I have tried to get used to new soft versions of numbers and pages now for around 3 weeks but it cannot make me to change my opinion that the eralier versions were much better. Unfortunately with OS X Maverick I have to use new versions for these apps, or do I, any hints?
    I already deleted once (2 weeks ago) OS X Maverick and switched back to OS X Mountain Lion (I use TM), but then decided after while to still update the op system soft to newest one available, as I've hoped that developers in Apple will come up with their soft improvements and bug fixes soon enough.
    Among the other disomforts (like pages, numbers and changed tag system) Safari is much slower than with previous version.
    Any hints are appreciated!
    Thanks, Paul

    https://discussions.apple.com/message/21546508#21546508 check this out

  • The extraction program does not support object 0JOB_ATTR

    HI all,
    I'm getting the following error when execting 0JOB_ATTR extractor in R/3 system (via RSA3):
    The extraction program does not support object 0JOB_ATTR
    Message no. R3009
    Diagnosis
    The application program for the extraction of data was called up using the invalid InfoSource/invalid InfoObject 0JOB_ATTR.
    System Response
    The data extraction is terminated.
    Procedure
    Check the SAP Support Portal for the appropriate Notes and create a customer message if necessary.
    I've found various threads with this error (or similar ones), but none of them are solved (or not published solution). Haven't found any SAP notes yet either, so any input would be very helpfull.
    Thank you.
    G.

    0JOB_ATTR not in use and SAP replaced this with 0EC_CJOB_ATTR... U have to use 0EC_CJOB_ATTR to load master data for 0JOB.
    Even i faced the same problem and found the following info in one of the SDN thread, and we are using 0EC_CJOB_ATTR (make sure u have data in table HRP5050).
    I have sent a message to SAP asking for the solution . Below is the reply what they gave.
    "This error appears because of naming conventions we have to switch the name of the Data Source from 0JOB_ATTR to 0EC_CJOB_ATTR. Please use this data source to extract the compensation job attributes to BW.
    Note also that data source 0EC_CJOB_ATTR extracts data from table HRP5050.
    If no data is being extracted please do the following:
    If you have data in HRP5050 and still do not get any data please try the following :
    1) Take over the Data Source from the business content (RSA5)again and check in RSA3 .
    2) Replicate the Data Source to BW
    3) Activate the Info Source again.
    4) Delete any previous delta initializations for the datasource.
    5) Initialize the delta again
    6) Try to load data".

  • Suddenly " display does not support HDCP " - March 2014

    Hello Sky peoples Having had no trouble with my Sky+ HD and my LG TV for months and months I am now getting this "does not support HDCP" dialog every time I switch on. The TV was on then suddenly it blacked out and wouldnt restart - so I had to de-power at the socket. After restart, this error dialog always appears - and no HDMI signal I have tried all the remedial actions, power-down restarts, cable switchovers, updated box software, unplug/replug The display still works fine on bluray and xbox 360The sky box is still putting out a signal on composite video. yinch'14

    Hi there Yinchy, 
    Thank you very much for joining us on the community forum and posting your query. 
    I am extremely sorry to see that you are experiencing this issue. 
    There are a number of things that you can do to try to resolve this. 
    Firstly, Reset the HDMI signal. 
    Using the Sky remote:
    1) Press Standby on the Sky remote. Standby light displays. 
    2) Switch off the power supply or remove the plug at the mains socket.
    3) Switch connection equipment to standby and disconnect at the mains socket. 
    4) Confirm no lights remain on the Sky box or any connected equipment. 
    5) Wait 60 seconds, then switch the TV on at mains socket. 
    6) Switch the TV to the correct HDMI or DVI input. 
    7) Switch the Sky box on at the mains socket. 
    8) Wait 2 - 4 minutes after the standby light displays. 
    9) Switch on all connected equipment at the mains socket. 
    10) Press Sky to switch on the Sky box. The green light displays. 
    Please let me know how you get on with this and I will be able to help you further if required. 
    Many Thanks, 
     

  • Error: Device type SWIN does not support page..

    Hi All,
    I'm working on smartforms which print sticker of size 5 cm width and 2.5 cm hight. I made page of same above mention size. but when i'm trying print this, it will show following error:
    Device type SWIN does not support page for  ZSTICKER(my page name).
    Please do needful help ASAP.
    -Dharmesh

    Hi,
    You need to link your new page to a device type.  Use transaction SPAD. Go into the device type and click on the 'Format' button, this will list the supported formats, switch to change mode and add your new page format (ZSTICKER).
    Regards,
    Nick

  • ZHT16MSWIN950 does not support accents

    Hi,
    my database was created with this CHARACTER SET = ZHT16MSWIN950 because it is been used in Taiwan and this is the character set that I found for chinese characters. My application uses accents in the sql sentence, for example:
    SELECT DISTINCT "COBROS_ANTICIPADOS"."F_RECEPCION",
    decode(cobros_anticipados.tipo ,'C', 'Cheque', 'P', 'Pagaré', 'J', 'Caja', 'Transferencia' ) as c_tipoc
    FROM "COBROS_ANTICIPADOS"
    when I run my application I get the error ORA-1756 becuase of the accent, If I change the sql sentence and I use
    SELECT DISTINCT "COBROS_ANTICIPADOS"."F_RECEPCION",
    decode(cobros_anticipados.tipo ,'C', 'Cheque', 'P', 'Pagare', 'J', 'Caja', 'Transferencia' ) as c_tipoc
    FROM "COBROS_ANTICIPADOS"
    application does not fail.
    Sorry, I forgot to mention that the database version is 8.1.7.
    I can not change the sql sentence because application is also used in Spain.
    How can I change the character set in my chinese database in order to accept accent and chinese characters? Is there any superset for ZHT16MSWIN950?
    Thanks in advance for your help
    Mabel

    There are two issues here, actually. The first one is that ZHT16MSWIN950 does not support the character 'é'. You should either translate your application, if it is to support Chinese only (Spanish text is of little use on Taiwan, I guess), or switch to UTF8, as suggested by Gunther (AL32UTF8, if you upgrade to some newer version at the same time).
    The second issue is with the client settings for you application (NLS_LANG). You application uses literals in one of the Western European character set (WE8ISO8859P1 or WE8MSWIN1252, probably). This is the character set that must be used in NLS_LANG for the literals to be interpreted correctly. If you set NLS_LANG as expected, the character 'é' will be translated to a question mark in ZHT16MSWIN950 and the query will not fail. The result will be 'Cheque', 'Pagare', 'Caja', or 'Transferencia', because ZHT16MSWIN950 has an explicit replacement character for 'é' equal 'e'.
    Of course, if you set NLS_LANG to WE8..., then the application will not be able to process Chinese characters. Therefore, to have both, Spanish and Chinese, you need to move the database and the client to UTF8. This will require the source code of your application to be converted to UTF8 as well. Note that you will also need a proper support from the operating system to be able to enter Chinese with the NLS_LANG set to .UTF8 The precise solution depends on the technology framework used by the application (client/server?, 3-tier?, Windows?, Unix?, etc)
    -- Sergiusz

  • Lightroom 3 does NOT support raw files for the  Canon Sureshot S95

    Have just bought the new Canon Sureshot S95
    after contacting Adobe support I am told Lightroom 3 does NOT support raw files for the
    Canon Sureshot S95.
    Come on Adobe.....please provide an update asap.

    (1) Well Boss I did what you said and used Canon DPP to convert to TIFFs. Choices are 8-bit TIFF or 16-bit TIFF - I chose 16-bit because part (90% part) of the reason for wanting to work in RAW is to keep the bit depth of teh original. On my EOS 40D it is supposedly 14 bits, which gives great scope to play with the levels & curves without seeing poster effects. If I choose 16 bit TIFF then each S95 image becomes a 70MB file, parallel to my JPEG and RAW.  Hardly a satisfactory solution.
    (I realise, however, that I don't actually know the bit depth of the S95 RAW file - anybody? ). 
    (2) SUGGESTION-  even if you are adding S95 support to the next update (which I dearly hope), be kinder to those with new cameras in general and allow LR to import JPEGs if it cannot import the RAWs (overriding if necessary the 'ignore JPEG' preference setting).  I am sure users with that preference would still prefer a JPEG than no picture at all!
    Since I discovered this compatibility problem, I switched the camera to record RAW+JPEG*. To my great irritation LR3 ignores the JPEGs even though it cannot load the RAWs.  So if I want to import from one supported camera (EOS40D) and one unsupported camera (S95) I have to keep going into preferences to switch on and off the 'ignore JPEG' function.
    JJ
    *  (this seems to be a setting that needs doing in the various different modes of the camera, by the way).

  • HT204655 Photos for Mac does not support semi professional camera Nikon D7000!

    Since Nikon does not support USB storage mode, the (semi)professional line of Nikon cannot be used to import pictures!!
    This is a serious flaw in the program. Aperture supports Nikon D7000, Image Capture supports the camera but the latest and greatest has forgotten all about supporting market leader's camera's?
    The main and only reason NOT to use Photos... Or did I miss something here?

    Sorry guys, forget all about it. I switch my camera off and on again (while it was connectoed to the Mac) and it appeared in Photos.
    No idea what happened, but I can import my pictures.
    Cheers,

Maybe you are looking for