3750-s IOS Issue

Hi all
what is the difference between
3750-s 3750-e
only Enahanced image if so
can i upgrade 3750-s IOS to 3750-e
i will perform all the task what 3750-e can give ??
ram

Hello,
actually, to begin with, the naming convention for the standard and enhanced images has been changed. The standard image is now IP Base, and the enhanced image is IP Services. Have a look at the product bulletin below:
The feature pack naming convention is changing in the 3560 and 3750 series switches. This is being done in order to make them match more closely to the naming scheme for our router products.
The "Standard" software load/license is being renamed "IP Base"
The "Enhanced" software is being renamed "IP Services"
A new feature pack, "Advanced IP Services" is being added for the primary purpose of adding IPv6 support on top of the Enhanced feature pack.
Regarding the difference between the two images, IP Base (standard) and IP Services (enhanced), have a look at the Q&A below. Scroll down to the question right under Table 1:
Cisco Catalyst 3750 Q&A
http://www.cisco.com/en/US/products/hw/switches/ps5023/products_qanda_item09186a00801b0971.shtml
As for the upgrade procedure, check this link:
Working with Software Images
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3750/12225sed/scg/swiosfs.htm#wp1017927
HTH,
GP

Similar Messages

Cisco 3750 Ghost Multicast Issues

We are having problems with Symantec Ghost 8.0 (Solution Suite 1.0) multicast sessions autonegotiating and transmitting at 10MB half duplex over stacked 10/100 Catalyst 3750s (WS-C3750-48PS-E). Both sides of the connection are set to autonegotiate. The clients will connect at 100MB full duplex and start the multicast session but then we will immediately see one port on the 3750 drop to 10MB half duplex and log thousands of collisions. If we kill the session and drop that system out of the mulicast and retransmit, then another port will automatically drop to 10MB half duplex as soon as the data starts to push. We use the same NIC chipset and NDIS drivers for Ghost throughout our entire operation but are only having this problem with two switches in the stack (7 total). If this were an overall incompatibility issue between the NDIS driver we're using (Broadcom 57xx), ghost, and the Cisco IOS then why do we not see this behavior on all of our switches? Our operation is too large (university) to hard code 100MB full duplex on both sides of the connection so we really need autonegotiation to work. We do not see any collisions on these switches when we are not using Ghost multicast. CPU and memory utilization on the 3750s are normal while the session is transmitting. We've tried the suggested fixes from Symantec (which really only included messing arround with TTL values on the ghost server end) and different versions of NIC drivers to no avail.

There are multiple clients receiving the mcast stream and each time a different client/port has the problem. All it takes is one port throttling down to slow the ghost multicast for the entire session (effectively a 15GB image which should take 40min to ghost at 100MB full duplex takes 4.5 hours to complete). IGMP snooping is working as far as I can tell. We're not seeing any multicast or broadcast packet floods during the ghost session and I'm seeing the IGMP, CGMP, and PIMv2 communications happening between the switches and routers via packet sniffs. We aren't doing any deliberate bandwidth throttling at all (QoS not enabled).
We've circumvented the Cisco switches in question with several different portable switches from other manufacturers and can image out fine at 100MB full duplex. As I stated in my original post, we can also ghost through other 3750s in the same stack with no problem. I also have two other floors in our building that use stacked Catalsyst 3750s and we have no issues with them as well.
We're not getting any packet loss or corruption. Just reduced throughput.

3750 Stack Switch Issue

Hi
I have Stack of 7 3750 Switches. In that Switch 1 is master with 15 Priority and other switches are Member but because of some reason switch 1 rebooted and then Switch 2 becomes Master because it’s having 14 Priority.
We have 2 uplinks which connected on switch 1 (1/1/1) and switch 6 (6/1/1) Tengig port. Also we have 4 AP connected on switch 6.
So we observed that the Switch 1 came up and after that 3 AP is disconnected from WLC. if we disconnect the uplink port on Switch 1 (1/1/1) AP will connect the WLC and using uplink 6/1/1 but if we connect uplink port 1/1/1 and disconnect the uplink port 6/1/1 all 4 AP will disconnect from Network.
We try to connect the Uplink 1/1/1 to Switch 1 other port 1/1/2 but face the same issue. So we reconnect the port 6/1/1 and used the same link which connect on 1/1/1 to switch 7 (7/1/1) and AP will connect on WLC. So as per this troubleshooting we thought some issue with Network Module or Switch of Switch1.
So we Swap the Network module between Switch1 and Switch7 and connect the uplink on 1/1/1 but face the same issue and if we connect the same uplink on Switch 7 Ap connect to WLC.
So we thought that Switch is having issue. But before raising an RMA for Switch we observer 1 more thing that. Earlier that when the Switch 1 is Master all 4 AP's connected to WLC and working fine but when the Switch1 became rebooted and Switch2 became Master issue started. So we rebooted the Switch 2 and make switch master and found that while connecting on port 1/1/1 of Switch port AP's are able to connect to WLC and Issue resolved.
So I wants to know that is there any requirement that If the high priority switch rebooted and after came up it should not be Master then connected uplink will not work.
Also let us know what’s happen if the high priority switch came up in network. Means it’s will became Master or Menber.

Just now i Found one bug which is matching on our issue.
3750x stack fails to update ARP table after reboot causing traffic loss
BUG ID:-CSCtz98066
Symptoms: When the master switch (Switch A) is reloaded or loses power and
rejoins the stack as a member switch, any traffic stream being sent through
Switch A is unable to be received by the destination because the newly joined
member is not able to establish an ARP entry for the next hop router/switch.
Debugs confirm that Switch A does not send a GARP/ARP for the next hop, though
traffic continues to be sent to the switch.
Conditions: The symptom is observed when only Switch A has a physical
connection between the source and destination router/L3 switch. The newly
elected master (Switch B) does not.
Workaround: Ping destination from Switch A, forcing ARP request/response.
Also affected version is 12.2(58)SE and15.0(1)SE2 and we are using IOS 12.2(58)SE.
So we are going to upgrade the devices by this weekend with IOS 15.0(2)SE5.
Will update you once we upgraded the switches.

3750's - Throughput Issue.

I have a throughput issue on 3750's that I cannot find a reason for.
Here are the models and SW versions:
Switch Ports Model SW Version SW Image
1 28 WS-C3750G-24TS 12.2(20)SE C3750-I5-M
* 2 52 WS-C3750-48TS 12.2(20)SE C3750-I5-M
3 52 WS-C3750-48P 12.2(20)SE C3750-I5-M
I am encountering slow response between servers in one vlan and SOME clients in another vlan.
If I place a "SLOW CLIENT" in the same VLAN as the server (Same ports/cabling etc) the throughput problem goes away.
The intervlan routing takes place withing the stack itself and not externally.
I can find no reason for this behavior, CPU/Memory are well within limits.
I have been reading IOS release notes but can find no mention of this. I see no other people on this forum having similar issues.
Does anyone have any thoughts ?

If you have double checked the client and switchport settings to make sure they match exactly then I'm not sure . It could be something like this , at least soemthing to check.
CSCed30201 Bug Details
Headline Temporary Packet loss maybe exhibited by the switch - stack cable
Product IOS
Feature OTHERS Components Duplicate of
Severity 2 Severity help Status Resolved Status help
First Found-in Version none All affected versions First Fixed-in Version Version help
Release Notes
SYMPTOMS / CONDITIONS
Cisco has found occasional intermittent contact on the 3750 product
stacking cable when using the "Fox" labled speciified cables. The location
below shows a photograph of the label showing the word "Fox" printed on the
label.
Sjc-fs1\WG-D\DSBU-Escalation\Published\Bugs\CSCed30201\3750_Bad_Stacking_Cable_Label.doc
WORKAROUND:
These "Fox" labeled cables should be replaced. Contact Cisco's TAC and
request a cable only replacement.
No problem exists with the 3750 switch itself and should NOT be replaced.
The customer should be advised that the "Fox" labeled cable should be
destroyed so that the customer will not accidentally place the defective
cable back in service at some later time.
BACKGROUND:
Failures were found in Cisco's DSBU lab that cause an intermittency resulting
in reduced traffic speed.
Failure analysis was completed by the cable / receptical vendor. The failure
indicated a substandard design, with an out of tolerance tongue in the plug and
potential misalignment in the receptical. This vendor has been disqualified
at this time.

IOS issue 4005 error Iphone 5 HELP!!

I have had my phone a while and its been working great. I was using the phone in IOS7 and again no issues. I have updated to IOS 8 and now it keeps telling me to connect to Itunes and when I do I get an error message with code 4005.
I took the phone to an apple guru and the respose was an absolute joke. They are trying to tell me that (even tho the phone worked perfectly before the update) the IOS update has detected a hardware fault and will not restart. They are then saying i need to pay them £200 to get a new Iphone 5!!!!! Sorry Apple send an update which they recommend you do and then it renders your phone useless, then I have to shell out £200 to get a new phone!!!!
Can anyone help me with this error message and how to fix it cause Apple and their staff have been useless!! Dont think i will be staying with Apple come updgrade time. Total Joke.

thanks for the suggestions, i tried the ideas you suggested but i dont even get a camera showing for the rear camera, i also noticed the torchlight no longer works. i did all the steps but no luck.
So I took my camera to the genius bar this weekend as well as walking through various steps with the apple guys in ohio support over the net.
With the guys at the genius bar, after i insisted that it must be software as the rear camera stopped working only after the softwre update, they continued to assure me it was hardware and talked me into letting them replace the camera, they then took it to the back and tried fixing a camera and 30 minutes later came out and said the rear camera is no longer being detected and wanted me to replace the motherboard for yet more money. im glad they didnt charge me for the new camera though as it still didnt work.
anyway the motherboard idea i rejected as it was just 2 months out of warranty and had only stopped working the day after the release of 7.0.2, so im going to wait until the next few releases to see what happens, as i dont believe for a second its hardware. i expected a stock answer from apple and its exactly what i got even after my explanation of how it was working the day before the release. not overly impressed with the whole process.
i wanted to back down to 7.0.1 to confirm the camera still works but they said no chance so i cant even see if it still works ouside 7.0.2. anyway will update if i get any further progress.

Cropping pictures in iOS issue

Hello,
I would like to know if somebody else experience the following issue:
After cropping a photo using the native iOS photo application, the images are being sent as "original" size either by email, dropbox, etc.. I also connected my iPhone via USB, browse the picture folders and noticed that the pictures still in original size. In simple words, cropping does not work as expected.
On the iPhone itself, I can see the images perfectly cropped, but is when I want to "export" it or copy it somewhere else that I have this problem.
Any help?
P.S: I tried also on my iPad2 and the results were the same.
Thanks in advance.

When you connected your iPhone via USB, did you import them into the latest Aperture or iPhoto? They will show the edits, Preview won't.

All OS X is really buggy - mouse lag, bluetooth dropouts, FCP X beachballs - iOS issues with iTunes = CRAP

I have had so many issues of late with both OS X Mavericks and iOS 8, that I am looking to change. Bluetooth dropouts that infuriate me despite swapping to brand new batteries, cleaning terminals, adding alfoil to hold the batteries more snuggly, etc; to FCP X constantly beach-balling (and I have 32GB RAM running with OS X running from an SSD); to itunes refusing to play any of my content on my new iPhone 6+. I have erased the phone twice and reloaded content after setting it up as a "new phone".
Is this April, and I have missed something?
Come on Apple, you have become an absolute JOKE. iCloud not working, iOS 8 not working, Bluetooth dropouts, I can't verify my new iPhone with iCloud Keychain for some unknown reason (wants me to reset and retry all the time).
If I wanted this cr@p, I would have stayed with W7....
Anyone else having issues with the new OSs?

Hi Bob,
Thanks for taking the time to have a look - EtreCheck output:
EtreCheck version: 1.9.15 (52)
Report generated 5 October 2014 4:09:54 pm AEDT
Hardware Information: ?
Mac Pro (Mid 2010) (Verified)
Mac Pro - model: MacPro5,1
2 2.66 GHz 6-Core Intel Xeon CPUs: 12 cores
32 GB RAM
Video Information: ?
ATI Radeon HD 5870 - VRAM: 1024 MB
LED Cinema Display 1920 x 1200
DELL 1703FP 1280 x 1024 @ 60 Hz
System Software: ?
OS X 10.9.5 (13F34) - Uptime: 0 days 5:47:40
Disk Information: ?
HL-DT-ST DVD-RW GH41N
M4-CT512M4SSD2 disk0 : (512.11 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted>: 209.7 MB
OSX SSD (disk0s2) / [Startup]: 511.12 GB (146.33 GB free)
Recovery HD (disk0s3) <not mounted>: 784.2 MB
WDC WD1001FALS-41Y6A0 disk2 : (1 TB)
S.M.A.R.T. Status: Verified
EFI (disk2s1) <not mounted>: 209.7 MB
1TB Internal (disk2s2) /Volumes/1TB Internal: 999.86 GB (312.63 GB free)
Hitachi HDS722020ALA330 disk1 : (2 TB)
S.M.A.R.T. Status: Verified
EFI (disk1s1) <not mounted>: 209.7 MB
DRAFT (disk1s2) /Volumes/DRAFT: 1.29 TB (975.89 GB free)
Alt Backup (disk1s3) /Volumes/Alt Backup: 711.95 GB (52.38 GB free)
Recovery HD (disk1s4) <not mounted>: 650 MB
ST3000DM001-1CH166 disk4 : (3 TB)
S.M.A.R.T. Status: Verified
EFI (disk4s1) <not mounted>: 209.7 MB
disk4s2 (disk4s2) <not mounted>: 3 TB
Boot OS X (disk4s3) <not mounted>: 134.2 MB
ST3000DM001-1CH166 disk3 : (3 TB)
S.M.A.R.T. Status: Verified
EFI (disk3s1) <not mounted>: 209.7 MB
disk3s2 (disk3s2) <not mounted>: 3 TB
Boot OS X (disk3s3) <not mounted>: 134.2 MB
USB Information: ?
Wacom Co.,Ltd. Intuos5 touch M
Generic Mass Storage 4.03 GB
S.M.A.R.T. Status: Verified
EFI (disk7s1) <not mounted>: 209.7 MB
Mac 4GB (disk7s2) /Volumes/Mac 4GB: 3.68 GB (1.07 GB free)
Apple Inc. Display iSight
Apple Inc. Display Audio
Apple Inc. Apple LED Cinema Display
OWC      Express USB2 160.04 GB
S.M.A.R.T. Status: Verified
EFI (disk6s1) <not mounted>: 209.7 MB
160GB HD (disk6s2) /Volumes/160GB HD: 159.7 GB (42.54 GB free)
Seagate External 3 TB
S.M.A.R.T. Status: Verified
EFI (disk9s1) <not mounted>: 314.6 MB
3TB Time Machine (disk9s2) /Volumes/3TB Time Machine: 3 TB (3 TB free)
Seagate FA GoFlex Desk 2 TB
S.M.A.R.T. Status: Verified
EFI (disk8s1) <not mounted>: 209.7 MB
FCP (disk8s2) /Volumes/FCP : 2 TB (1.52 TB free)
BUFFALO HD-LBU3
C-Media Electronics Inc.       USB Microphone
Logitech USB Receiver
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
Logitech USB-PS/2 Optical Mouse
Firewire Information: ?
LaCie 2big triple (button) 800mbit - 800mbit max
S.M.A.R.T. Status: Verified
EFI (disk10s1) <not mounted>: 209.7 MB
FW 1TB (disk10s2) /Volumes/FW 1TB: 999.87 GB (701.87 GB free)
Configuration files: ?
/etc/sysctl.conf - Exists
/etc/hosts - Count: 37
Gatekeeper: ?
Mac App Store and identified developers
Kernel Extensions: ?
[loaded] at.obdev.nke.LittleSnitch (4212 - SDK 10.8) Support
[not loaded] com.avira.kext.FileAccessControl (1.0.0d1 - SDK 10.9) Support
[not loaded] com.roxio.TDIXController (1.7) Support
[not loaded] com.silabs.driver.CP210xVCPDriver (3.0.0d1) Support
[not loaded] com.silabs.driver.CP210xVCPDriver64 (3.0.0d1) Support
[not loaded] com.wacom.kext.wacomtablet (6.3.9 - SDK 10.9) Support
[not loaded] net.osx86.kexts.GenericUSBXHCI (1.2.7) Support
[loaded] net.osx86.kexts.NECUSBXHCI (2.2.7) Support
Startup Items: ?
CUDA: Path: /System/Library/StartupItems/CUDA
ProTec6b: Path: /Library/StartupItems/ProTec6b
Launch Daemons: ?
[running] at.obdev.littlesnitchd.plist Support
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.adobe.SwitchBoard.plist Support
[loaded] com.bombich.ccc.plist Support
[failed] com.edb.launchd.postgresql-8.4.plist Support
[loaded] com.fxfactory.FxFactory.helper.plist Support
[loaded] com.macpaw.CleanMyMac2.Agent.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] net.sourceforge.MonolingualHelper.plist Support
[loaded] org.cindori.TEAuth.plist Support
Launch Agents: ?
[running] at.obdev.LittleSnitchUIAgent.plist Support
[not loaded] com.adobe.AAM.Updater-1.0.plist Support
[loaded] com.citrix.AuthManager_Mac.plist Support
[running] com.citrix.ReceiverHelper.plist Support
[running] com.citrix.ServiceRecords.plist Support
[loaded] com.nvidia.CUDASoftwareUpdate.plist Support
[running] com.wacom.wacomtablet.plist Support
[running] net.culater.SIMBL.Agent.plist Support
User Launch Agents: ?
[not loaded] com.digitalrebellion.PreferenceManagerAutoSave.plist Support
[not loaded] com.facebook.videochat.[redacted].plist Support
[not loaded] com.google.keystone.agent.plist Support
[not loaded] com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist Support
[not loaded] com.macpaw.CleanMyMac2Helper.scheduledScan.plist Support
[not loaded] com.macpaw.CleanMyMac2Helper.trashWatcher.plist Support
[not loaded] com.redgiantsoftware.updater.plist Support
[not loaded] com.Wondershare.TunesGoWatchDemo.plist Support
User Login Items: ?
iTunesHelper
TrimCheck
Avira
Internet Plug-ins: ?
Default Browser: Version: 537 - SDK 10.9
AdobeExManDetect: Version: AdobeExManDetect 1.1.0.0 - SDK 10.7 Support
WacomTabletPlugin: Version: WacomTabletPlugin 2.1.0.6 - SDK 10.9 Support
AdobeAAMDetect: Version: AdobeAAMDetect 1.0.0.0 - SDK 10.6 Support
FlashPlayer-10.6: Version: 15.0.0.152 - SDK 10.6 Support
Silverlight: Version: 4.1.10329.0 Support
Flash Player: Version: 15.0.0.152 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
CitrixICAClientPlugIn: Version: 11.8.2 - SDK 10.7 Support
SharePointBrowserPlugin: Version: 14.1.0 Support
AdobePDFViewer: Version: 10.1.1 Support
EPPEX Plugin: Version: 3.0.5.0 Support
Audio Plug-ins: ?
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 2.0 - SDK 10.9
AppleAVBAudio: Version: 203.2 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
iTunes Plug-ins: ?
Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
User Internet Plug-ins ?
Google Earth Web Plug-in: Version: 7.1 Support
3rd Party Preference Panes: ?
ApplyLUTPane Support
CUDA Preferences Support
Flash Player Support
ProCutX Server Support
ArcanaStartupSound Support
WacomTablet Support
Time Machine: ?
Skip System Files: YES - System files not being backed up
Mobile backups: OFF
Auto backup: NO - Auto backup turned off
Volumes being backed up:
OSX SSD: Disk size: 476.01 GB Disk used: 339.73 GB
Destinations:
Time Machine [Local] (Last used)
Total size: 3 TB
Total number of backups: 1
Oldest backup: 2014-08-08 12:41:49 +0000
Last backup: 2014-08-08 12:41:49 +0000
Size of backup disk: Excellent
Backup size 3 TB > (Disk size 476.01 GB X 3)
Time Machine details may not be accurate.
All volumes being backed up may not be listed.
Top Processes by CPU: ?
      1% WindowServer
      0% fontd
      0% softwareupdated
Top Processes by Memory: ?
590 MB mds_stores
524 MB com.apple.IconServicesAgent
229 MB com.apple.WebKit.WebContent
197 MB softwareupdated
164 MB Safari
Virtual Memory Information: ?
24.40 GB Free RAM
5.09 GB Active RAM
707 MB Inactive RAM
1.79 GB Wired RAM
429 MB Page-ins
0 B Page-outs

SDK 16 using new AOT on iOS issues: unresponsive on return from CameraRoll, list skins confused

I am having issues with the "-useLegacyAOT no" (now default) and iOS apps. Under SDK 15 using "-useLegacyAOT yes" no issues. With SDK 16 the app has issues with many things, for example datagrid/list skins don't work - if you manually skin using setRendererStyle, it seems ALL the skin states are using the Selected skins, and the upSkin state uses the selectedUpSkin skin as far as I can make out (in tests this seems to be the case). Another is the app becomes unresponsive to touch on returning from cameraRoll, camera to take a picture or video to record a video - my app is full screen, when it returns from one of these, it is no longer full screen (the top info bar is visible), and I am using stage.displayState = StageDisplayState.FULL_SCREEN_INTERACTIVE when returning from these calls, which worked under the legacy AOT. Since the app is unresponsive, the only option is to reboot the iphone and restart the app - not really an option.

Just catching up with testing using the latest SDK 17 (115) and finding the following: With SDK 16/17 on iOS the app has issues with datagrid/list skins - if you manually skin using setRendererStyle, it seems ALL the skin states are using the Selected skins, and the upSkin state uses the selectedUpSkin skin as far as I can make out (in tests this seems to be the case).
I am also noticing that sometimes on return from the camera, cameraroll, and video camera, the app will sometimes hang - not always. I am continuing to test. The hang actually closes the app quickly.

IOS Issues

After some limited success with getting my app on iOS, I have hit a roadblock. At first, I was publishing my app and it was working great. All of a sudden after fixing some issues, it no longer works. I reverted back the changes but no success. It works in desktop and on Android just great. Here is what I am seeing
works (kind of)
- If I use low res iphone size it works (but looks terrible)
- If I use high res iphone or ipad with CPU, it also works but looks terrible and is poor performance (also the native extension alert does not work)
doesn't work
- If GPU is on, there are just some wierd shapes on the screen (but mostly black)
What doesnt work was actually at one point working great with great performance (including the native extension). The remote debugging shows no errors. Hopefully this is something someone has seen and an easy fix but it is driving me crazy.

Hello Everyone,
We request you all to try your applications with http://labs.adobe.com/technologies/flashplatformruntimes/air3-5/
Release Notes - http://labsdownload.adobe.com/pub/labs/flashplatformruntimes/shared/air3-5_flashplayer11-5 _releasenotes.pdf
Please let us know how it goes.
-Thanks
Pahup

CameraUI + iOS issues

Hi,
We are having some issues with the CameraUI for an app we are devloping for iOS.
We are currently using AIR SDK 3.6
1) When invoking the CameraUI and using Stage3D, Starling or any other framework that takes advantage of the GPU in iOS we loose the context. I guess this is an unavoidable problem and the only solution is to handle the context loss (in the case of Starling is easy), but the visual result is not ideal, the delay between the CameraUI interface finishing and the app restoring the context (All Textures etc), makes it look like a bug. Also I always though that was impossible to loose the context in iOS, is this affirmation correct?
2) When in the CameraUI interface if the user clicks the device "HOME" button, the app goes to the background but when the user comes back to the app, the CameraUI interface appears with the shooter graphics closed. Clicking the Camera button (to shoot) does nothing, in fact freezes the app completelly, and clicking cancel and invoking the CameraUI again makes the shooter animation to play twice... This kind of behaviour doesnt happen in the native Camera app., when the user comes back from the background the shooter animation opens again normally.
Any thoughs?
Thanks
Luis

Can you please report a bug for the same @bugbase.adobe.com with a sample app(source code ,swf, app-xml and assets/ane) with which bug can be reproduced?
Also you can provide me the sample app(source code ,swf, app-xml and assets/ane) @[email protected] so that I can give it a try.
Please share the bug number here.
Thanks,
Nimisha

IOS Issues w/ Restoring a Backup

So, I was switching two iPhone 4's.... one iPhone had been upgraded to iOS 6.1.2 and I made a backup one one computer through iTunes. The other iPhone was still on 6.1.1 and I made a backup . I didn't think it would be an issue...
When I switched the phone numbers succesfully through Verizon, I began restoring the iPhones with the backups. The iPhone on iOS 6.1.1 asked me to upgrade I believe... somehow iOS 6.1.2 got downloaded before the backup was able to be restored.
So... The backup made with 6.1.2 worked beautifully, no issues, but the backup made with 6.1.1 is not working. It says "iTunes cannot restore the iPhone _____ because the backup was corrupt or not compatible with the iPhone that is being restored."
So if I can see this correctly: A backup made through iOS 6.1.1 cannot be restored to an iPhone with iOS 6.1.2? If indeed correct, what the heck can I do to restore it somehow? Is there a way?

Okay, I was mistaken. iOS 6.1.1 was only for the iPhone 4S so I suppose I had 6.1.

3750-48/3750-12s compatibility issue

Has any one ever seen a problem like the following?
We have a stacked pair of 3750-48s (SMI) ether-channeled to a stacked paire of 3750-12s switches (EMI). The channeled ports are each on separate switches within their respective stacks.
Everything is woring fine. We power down one of the 3740-12s and we lose 1 ping across the etherchannel (works perfect). Howver, when we first power back up the 3750-12, and I mean within a couple of seconds the link light comes on on the 3750-48 that it connects to and the 3750-48 thinks the channels is back up. We begin loosing pings until the 12s is fully powered up. Seems like a bug to me. We are running 12.2.25 Code. I'm in the process of opening a TAC case but just Thought I'd toss it out here.
Also, we removed the stack configuration and Etherchannel and just connected one 48-port switch to one 12-port switch. The same issue happened. As soon as we powered up the 3750-12s the link light on the 48port comes up ( 2 seconds tops).

Hi,
I have seen similar between 3750's with Etherchannelled uplinks to 6509 switches
It turned out to be a bug with running different versions of spanning tree between both sets of switches.
I think the 3750's were running PVST+ and the 6509's were running RSPT.
This was diagnosed by a Cisco consultancy, when one of the Etherchannel links was dropped, it caused EIGRP to reconverge and all sorts of timeouts occured for a while. Unfortunately i haven't had time to test it since the changes were made but i know the consultancy reproduced this issue in their lab which resulted in them hardcoding both sets of switches to PVST+
Have a look and see if this could be the same for you.
Rgds
PJD

ME3600x IOS issue

Hi
After upgrade to 15.3(3)S and on one switch with 15.3(1)S1 i got error
(config)#interface GigabitEthernet0/11
(config-if)#service-policy output qos-test
Qos: Out of tcam resources to execute command
QoS: Policy attachment failed. Configuration exceeds hardware resources
for policy qos-test
#show logging
Nov 21 15:47:28: %QOSMGR-3-TCAM_EXHAUSTION: Internal Error in resource
allocation
bg-ba-m-1#show platform tcam utilization qos
Nile Tcam Utilization per Application & Region:
ES == Entry size == Number of 80 bit TCAM words
==================================================================
App/Region            Start Num Avail ES    Used Range Num Used
==================================================================
QOS                   36864      4096   2
     nile0                                                       13
     nile1
(config-if)#service-policy output qos-test
Qos: Out of tcam resources to execute command
QoS: Policy attachment failed. Configuration exceeds hardware resources
for policy qos-test
#show logging
Nov 21 15:47:28: %QOSMGR-3-TCAM_EXHAUSTION: Internal Error in resource
allocation
#show platform tcam utilization qos
Nile Tcam Utilization per Application & Region:
ES == Entry size == Number of 80 bit TCAM words
==================================================================
App/Region            Start Num Avail ES    Used Range Num Used
==================================================================
QOS                   36864      4096   2
     nile0                                                       13
     nile1                                                         6

Hi startx001, hope you will be fine.
Did you a find a solution for this issue?
I'm facing same problem

HT4759 iOS issue

Hi,
Can someone help me to find a solution on how to upgrade my ipad 1. (iOS 5) to either 6 or 7. I have been having problem on downloading the simplist feature like facebook.
Please your advise is needed.
Thanks.

Sell it and put the money towards a newer device. Any newer iPad model can run iOS 7.0.4.
(96174)

Ios issues and other questions

Hello!
First of all i would like to thank resdesign, zaxist and all of the dev team for helping here.
Second, i'm not good at coding and most likely i have used all of the bad practices possible here so continue at your own risk
Anyway, here is the page i've made in edge:
http://www.nocomprendo.ru
this will change soon, so if you want to see the version at the time of this post - please go here:
original (unstable on ios6/ios7): http://nocomprendo.ru/test1/america_test.html
no maps (unstable on ios6): http://nocomprendo.ru/test2/america_test.html
no maps and svg-s (stable): http://nocomprendo.ru/test3/america_test.html
you can download source file here: http://nocomprendo.ru/test1.zip
Most of the code is in stage's "composition ready".
It uses a instafeedjs to embed instagram (which is working stable and is easy to implement) http://instafeedjs.com/
It uses fbwall to embed facebook (which is laggy, outdated and i would not recommend it) http://www.neosmart.de/social-media/facebook-wall/
It uses external fonts which can be generated here http://www.font2web.com/
and the loaded to adobe edge. tutorial here: http://www.youtube.com/watch?v=a76Exc8NcqM \
(be sure to remove an .svg file!!!)
Not always legal, though if you need cyrillics (which is a pain as adobe webfonts have only three or four cyrillic fonts) it is a solution.
I would most likely embed wordpress to load some more external content anytime soon as i did it on another project, though i dont know how to do it from inside of edge and i would have to edit the files manually. (i would appreciate any links to tutorials)
Concerning the stability of the edge websites:
embedding of google maps (both old and new API) causes ios iphone/ipad safari and chrome to crash (ios6, ios7).
perhaps the nature of it is in huge iframes i am using. any ideas?
use of any svg files also causes ios iphone/ipad safari and chrome to crash (more likely in ios6 less likely in ios7).
this was mentioned several times on the board and seems like it is not solved yet.
I have questions on making advanced preloaders with percentage bar. (i have seen zaxist's thread) but is there any walkthrough on embedding any javascript preloader like these:
http://codecanyon.net/item/percentage-preloader/5523389?WT.ac=solid_search_item&WT.seg_1=s olid_search_item&WT.z_author=CodingJack
Also, current preloader option available in edge replaces the white screen before loading composition, but everything that happens in composition ready is seen by website visitor and looks odd. Shall i use creationcomplete or anything else instead?
p.s. yeah, its me going down the south america on a motorcycle, so if youre interested you may follow me in facebook or instagram

still relevant..

3750-s IOS Issue

Similar Messages

Maybe you are looking for