3750 switches list of instances to monitor

Hello,
Does anyone have a list of th main instances to monitor on cisco switches as well as their OIDs( ie: CPU, memotry,....etc)
Regards

Hi 950358,
these are the few:
monitor alert log
Check for Instance & Database to be up
check for database_name,open mode, log mode, startup_time
Check for all the necessary Processes to be up like pmon smon etc
Check the processes of the Application in the server FNDLIBR etc
Check Listener processes to be up
free and used space on server
Size of the Database
Number of Tablespaces
Number of Datafiles
Number of Invalid objects
list of invalid objects
locks on db
Number of Archives generated the previous day
List the archive log generated
check for archivelogs shipped to standbydatabase (if u hav DR)
Latest redo log SCN# in Primary and Standby database
TNS Ping results to STANDBY database
Login and check the Application front end
Errored Requests submitted in the last 24 hours
Verify the managers are all running properly
Check for a sample Report (submit active users)
Check for VNC is working
Buffer Hit Ratio
Library Hit Ratio
check for number of DB users
Completed concurrent requests that have run for more than 2 hrs
Current Running Requests
Request Currently Running for more than 2Hrs
Error Concurrent Requests in the last 24 Hrs
Check database backup (RMAN) status (daily + weekly + monthly) as per your backup policy
it is better to use oem regarding automated alerts.
HTH
Regards,
Haafiz

Similar Messages

WAAS Configuration for 3750 Switch

I am configuring a 3750 switch with 12.2(52)SE according to:
(from https://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_52_se/configuration/guide/3750_scg.pdf )
This example shows how to configure SVIs and how to enable the web cache service with a multicast group list. VLAN 299 is created and configured with an IP address of 175.20.20.10. Gigabit Ethernet port 1 is connected through the Internet to the web server and is configured as an access port in VLAN 299. VLAN 300 is created and configured with an IP address of 172.20.10.30. Gigabit Ethernet port 2 is connected to the application engine and is configured as an access port in VLAN 300. VLAN 301 is created and configured with an IP address of 175.20.30.50. Fast Ethernet ports 3 to 6, which are connected to the clients, are configured as access ports in VLAN 301. The switch redirects packets received from the client interfaces to the application engine.
Note Only permit ACL entries are being used in the redirect-list; deny entries are unsupported.
Switch# configure terminal
Switch(config)# ip wccp web-cache 80 group-list 15
Switch(config)# access-list 15 permit host 171.69.198.102
Switch(config)# access-list 15 permit host 171.69.198.104
Switch(config)# access-list 15 permit host 171.69.198.106
Switch(config)# vlan 299 WEB SERVER
Switch(config-vlan)# exit
Switch(config)# interface vlan 299
Switch(config-if)# ip address 175.20.20.10 255.255.255.0
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 299
Switch(config)# vlan 300 WAE
Switch(config-vlan)# exit
Switch(config)# interface vlan 300
Switch(config-if)# ip address 171.69.198.100 255.255.255.0
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/2
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 300
Switch(config-if)# exit
Switch(config)# vlan 301 CLIENTS
Switch(config-vlan)# exit
Switch(config)# interface vlan 301
Switch(config-if)# ip address 175.20.30.20 255.255.255.0
Switch(config-if)# ip wccp web-cache redirect in
Switch(config-if)# exit
Switch(config)# interface gigabitethernet1/0/3 - 6
Switch(config-if-range)# switchport mode access
Switch(config-if-range)# switchport access vlan 301
Switch(config-if-range)# exit
===================================================================
Question: How do I configure my WAE to play nicely with this switch?

Hi James,
Here is the link to WCCP config part on WAE:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v441/configuration/guide/traffic.html#wp1041742
In your case, if my understanding is right, VLAN300 is where you want to connect WAE and WAE is also L2 adjacent. if that is true, here is the config you need on WAE:
wccp router-list 1 171.69.198.100
wccp tcp-promiscuous router-list-num 1 l2-redirect mask-assign l2-return
wccp version 2
Please note that 3750 supports L2 redirection only with redirect IN statements on 3750 interfaces connected to servers and clients.
Hope this helps.
Regards.

How can I mirror all ports on CISCO 3750 switches to one Gigabyte port?

Hi,
I have a requirement to mirror all the ports on my 7 CISCO 3750 switches, which are in 3 separate stacks, to one single Gigabyte Ethernet port.
Does anyone know how I can do that?
Thanks in advance.

Vlad, thanks a heap for your response.
I want to apply to my sitation. Please let me know if I get them right in the following:
Catalyst A
vlan 901
remote-span
monitor session 1 source interface fastethernet 1-48 (I want to monitor all ports on the CISCO 3725)
monitor session 1 destination remote vlan 901
Catalyst B
vlan 901
remote-span (If I don't need to monitor this switch, do I still need to put anything into this switch at all?)
Catalyst C
vlan 901
remote-span
monitor session 1 source interface fastethernet 1-48 (I want to monitor all ports on this switch as well)
monitor session 1 source remote vlan 901
monitor session 1 destination interface gigabitethernet 3 (There are 4 Gigabit Ethernet Uplink in CISCO 3750, I want all the traffic to go to port 3, is this the right way to do?)
Thanks in advance.

Snmp for 3750 switch stack

Hi,
I have two 3750 switch stack together with one ip address mange the stack.
Can I monitor the memory and cpu for each individual switch? what is the oid then?
Thanks.
C.K.

Hello CK,
On the Catalyst 3750, the stack master handles the SNMP requests and traps for the whole switch stack.
The stack master transparently manages any requests or traps that are related to all stack members. When a new stack master is elected, the new master continues to handle SNMP requests and traps as configured on the previous stack master, assuming that IP connectivity to the SNMP management stations is still in place after the new master has taken control.
So to answer your question, with the OID for CPU and Mempory usage the switch will return only values for the active master. The other stack members are hot standby and do not produce SNMP information for CPU and/or Memory.
HTH
--Leon

Switch List Menu in G/L & Vendor Line Item Display

Hi Dear All Experts,
I've 2 problems.
The first one is in the Vendor line item display program.
copied RFITEMAP and create custom program and then I create new structure (like FAGLPOSX) to show extra fields. (eg. Vendor, User)
New extra fields are shown when i execute but if I click switch menu from the setting menu, it is shown by the old fields not including new fields.
The second one is in the GL Line Item display program.
Even the Switch List menu is enable in the Vendor Line Item display custom program without changing anything for gui status, the switch list menu in my new custom program is disable.(copied from fagl_account_items_gl).
Thks all in advance..
TRA

the second question is now solved.
Include ZFAGL_ACCOUNT_ITEMS_DEF (C_REPID_GL LIKE SY-REPID VALUE 'FAGL_ACCOUNT_ITEMS_GL') I put custom program name in this field.
When I changed to std program name, the switch list menu is enable..
Only the first question is left..
Please let me know is there any way to solve...
Best Regards
TRA

I need to Enable the Switch list from menu bar

Hi Friends,
i   copied RFITEMAP Program and created the custom report and changes have done according to the requirement
After executing the custom report it was Disabled the SWITCH LIST Option(GRID/CLASSIC)
but standard report we can change layout GRID/CLASSIC from SWITCH LIST Option
How can i enable the Switch list option in Cutom report................
Please help me above issue..
Regards
Venkat Boddu
Edited by: venkat boddu on May 11, 2009 6:49 PM
Edited by: venkat boddu on May 11, 2009 7:01 PM

The option for Switch List is being excluded from the PF-Status when the calling report is not the RFITEM*.
Include LFI_ITEMSF01, Line 379
* list refresh and toggle: only if called by RFITEM**
if caller_repid(6) ne 'RFITEM'.
    wa_extab-fcode = 'REFR'.
    append wa_extab to rt_extab.
    wa_extab-fcode = 'LTOG'.      " Switch List option
    append wa_extab to rt_extab.
endif.
You can replace your Z program name in your Z include or change the condition like
if caller_repid(8) ne 'Z_RFITEM'.
endif.
I assume that your Z program name is Z_RFITEM
Regards,
Naimesh Patel

Connection of LC/APC fiber patch cords to Cisco Catalyst 6500 $ Cisco Access 3750 Switches

I have an LC/APC fiber patch cord infrastructure and I want to connect it to Cisco Catalyst 6500 & Cisco Access 3750 Switches. what type of transceiver should be used?
I read a note on Cisco website stating the following for Cisco SFP+ transceivers:
Note: "Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section"

Thank you, but my question is that I have a single mode fiber patch cord with LC/APC connector while cisco stating a note that only use LC/PC or LC/UPC type of connectors with SFP+ transceiver.
So what type of transceiver should I use to connect LC/APC patch cord to cisco switches? Is there another type or SFP+ still can be used?

802.1x "MachineorUser" Auth Mode strange behavior in 2950 & 3750 Switches

Good Day Support Team around the world,
Having started recently tests with 802.1x in a lab environment, I noticed a strange behavior related to authentication. First let me provide you with the network components I used.
supplicant:                    domain-joined laptop with Windows XP SP3 802.1x embedded client
authenticator1:              Cisco 2950-24
authenticator2:              Cisco 3750-24
authentication server:     MS NPS Windows Server 2008
1.     In the first scenario with 3750 switch when I connect the laptop to relevant port the machine authentication is successful. Then I try to login with a domain account and again the authentication is completed without any problem. Then I log off and user authentication is revoked and the machine authentication is used again without any issue. When I try to login again as local user the authentication fails as expected but the port remains disabled (port blinking amber) regardless the fact that port is configured for Auth-Fail Vlan. When I log off then the machine authentication is used again and the access is granted.
2.     In the second scenario with 2950 switch as authenticator, I follow the same steps as before and when I try to login as local user the authentication is failed and the port is assigned the Auth-Fail Vlan (as expected based on configuration). However when I log off it seems that the 2950 switch still use the Auth-Fail Vlan for that port and never authenticates again for machine authentication.
Could you please let me someone know if this is normal ( I suppose no). Please find attached the relevant debug output from the second scenario.
Thank you!!!

Hi,
basically what happens is that the maximum EAP packet size for communication between client and RADIUS server is negotiated. Therefore, in your case the switch notifies NPS that the client is capable of handling packets up to 9000 bytes in size.
EAP messages, especially those containing the server certificate, are usually bigger than 1500 bytes and arrive at the switch in multiple fragments:
Mar 6 15:50:11.881: RADIUS(0000002C): Received from id 1645/41
Mar 6 15:50:11.881: RADIUS/DECODE: EAP-Message fragments, 253+253+253+253+253+253+253+253+20, total 2044 bytes
Having learned that 2044 bytes is acceptable for the client, the switch forwards the full message in one chunk, but since your client is likely to have set the interface MTU to 1500, the packet is oversized and never reaches its destination.
And yes, I think changing the System Jumbo MTU to 1500 bytes would lead to the same result. If my memory serves me right, a new setting takes effect only after a reboot, so I'd suggest giving it a go in your lab first.
Best regards,
Josef

Question on ARP table on 3750 switch

Hi,
So I have a cisco 3750 switch directly connected to a 2851 router gig 0/0 interface.
Should the show arp command on the switch show an entry for the IP and mac address of the routers gig 0/0 interface?
I dont see one in there now and was just wondering.
Connectivity between the switch and router work fine right now.
thanks

HI Bill,
if u can ping from Swicth ro router,,,,then please check with this command: sh ip arp.
Just for Info;
To be able to ARP a device, you must have an interface (SVI) on that switch on that network. To ARP a device you must have an interface with a layer 3 IP on the same layer 2 vlan.
You will need to connect to a switch that has an interface on that vlan on it. I would traceroute to the host, and hopefully the next to last hop is the layer 3 switch, or if it's a router, connect to it and do a show cdp neighbors and see if you can find the switch that way. (If you do connect to the router, you'll find the ARP entries there, if it's a layer 3 switch, then it's both a router and switch in one box)
"sh mac address-table". This will give which MAC is connected to which port.
"sh ip device tracking interface gigabitEthernet ". This will give which IP is connectd to a port.
"sh ip arp" will give you a IP to MAC table
Regards
Dont forget to rate helpful posts.

List of instance and databases

My sql server contains multiple instances and each instance contains multiple databases.
Now how to list of all the instances and their corresponding databases?
i used select * from sys.servers for instances and sys.databases for number of databases.
But how to list of all the instances and databases using single query?

Hi
List all Instances
option 1: Pwershell
Get-Service | Where-Object {$_.Name -like 'MSSQL$*'}
Option 2: query this registry
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Microsoft SQL Server.....
Option 3: go to regitry HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Microsoft SQL Server\Instance Names
* Here you can find other option like OLTP and not just SQL
Option 4: RUN -> services.msc
Find all services named "SQL Server". The instance name is in the brakets
Option 5: Open sql server configuration manager -> SQL Server Services
There are more options if you need :-)
[Personal Site] [Blog] [Facebook]

AAA Radius accounting command is not taking in 3750 switch

Hi Cisco Support community,
I am facing a issue with radius accounting in Cisco 3750 switch with version 12.2. I am unable to start accounting for radius server.
This is the config that is on the switch for Radius.
aaa authentication login default group radius local
aaa authentication dot1x default group radius
aaa authorization exec my-authradius group radius if-authenticated.
radius-server attribute 6 on-for-login-auth
radius-server dead-criteria time 20 tries 5
radius-server host 10.100.1.225 auth-port 1645 acct-port 1646 key 7 14341A5801103F3904266021
radius-server host 10.100.1.226 auth-port 1645 acct-port 1646 key 7 05280E5C2C585B1B390B4406
When i try to add the following command for accounting, this is not saving.
(aaa accounting commands 0 default start-stop group radius
aaa accounting commands 1 default start-stop group radius
aaa accounting commands 15 default start-stop group radius)
If i do paste this command one by one after start-stop group it is showing only two options either tacacs+ or server, no radius option is there as well.
I tried to create a server group and add the radius server in the group. Even then when i am trying to implement the aaa accounting command with the server command it is not showing in show run.
Can anyone please help me with this issue.

Hi,
thanks for your reply but the thing is that i want to see the command that are being run by a user on this particular device. If i use the network command it will only show me the network-related service requests, including Serial Line Internet Protocol (SLIP), PPP, PPP Network Control Protocols (NCPs), and AppleTalk Remote Access Protocol (ARAP).
I have read the document from this link and it is stating that we can use command accounting. Below is the link
http://www.cisco.com/en/US/docs/ios/security/command/reference/sec_a1.html.
Can anyone please tell me if this a version issue because even in version 15.4 i was not seeing the radius option in the end
aaa accounting commands 15 default start-stop group (radius)- in radius place it was showing only Tacacs+ or group.

Best IOS version for 3750 switch

I have just received 2 3750 switches, but both have a different IOS version.
One has -> IOS version 12.1(19)EA1d
and the other has -> IOS version 12.2(25)SEB2.
I just want to use the switches as Gb collectors for a serverfarm seperatly (so no stack configuration) with a redundant uplink to my distribution layer.
Can someone advise my which IOS is the best for my network?
Thanx, Marty

Switch 1:
Cisco Internetwork Operating System Software
IOS (tm) C3750 Software (C3750-I5-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 05-Apr-04 22:06 by antonino
Image text-base: 0x00003000, data-base: 0x009206D8
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.1(14r)EA1a, RELEASE SOFTWARE (fc1)
2224-3750-037000137 uptime is 23 hours, 52 minutes
System returned to ROM by power-on
System restarted at 09:02:42 GMT Thu Aug 11 2005
System image file is "flash:c3750-i5-mz.121-19.EA1d/c3750-i5-mz.121-19.EA1d.bin"
cisco WS-C3750G-24TS (PowerPC405) processor (revision H0) with 118776K/12288K bytes of memory.
Processor board ID CAT0904X00B
Last reset from power-on
Bridging software.
1 Virtual Ethernet/IEEE 802.3 interface(s)
28 Gigabit Ethernet/IEEE 802.3 interface(s)
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:13:1A:65:50:00
Motherboard assembly number : 73-7058-12
Power supply part number : 341-0045-01
Motherboard serial number : CAT090400A0
Power supply serial number : LIT09020266
Model revision number : H0
Motherboard revision number : A0
Model number : WS-C3750G-24TS-E
System serial number : CAT0904X00B
Hardware Board Revision Number : 0x09
Switch Ports Model SW Version SW Image
* 1 28 WS-C3750G-24TS 12.1(19)EA1d C3750-I5-M
Configuration register is 0xF
Switch 2:
Cisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(25)SEB2, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 08-Jun-05 01:19 by yenanh
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.1(14r)EA1a, RELEASE SOFTWARE (fc1)
2224-3750-037000138 uptime is 59 minutes
System returned to ROM by power-on
System image file is "flash:c3750-ipservices-mz.122-25.SEB2/c3750-ipservices-mz.122-25.SEB2.bin"
cisco WS-C3750G-24TS (PowerPC405) processor (revision L0) with 118784K/12280K bytes of memory.
Processor board ID CAT0925Z0WZ
Last reset from power-on
1 Virtual Ethernet interface
28 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:14:A8:71:CA:00
Motherboard assembly number : 73-7058-13
Power supply part number : 341-0045-01
Motherboard serial number : CAT09251J90
Power supply serial number : PHI09220165
Model revision number : L0
Motherboard revision number : A0
Model number : WS-C3750G-24TS-E
System serial number : CAT0925Z0WZ
Hardware Board Revision Number : 0x09
Switch Ports Model SW Version SW Image
* 1 28 WS-C3750G-24TS 12.2(25)SEB2 C3750-IPSERVICES-M
Configuration register is 0xF

How to check if 3750 switch is using sslv3

Hi Everyone,
i an trying to https to 3750 switch using firefox below is error message
Firefox cannot guarantee the safety of your data on 10.0.0.4 because it uses SSLv3, a broken security protocol.
Advanced info: ssl_error_no_cypher_overlap
Learn More…
ip http secure-server ---- is configured on 3750.
i checked config on 3750 switch it does not show if sslv3 is enabled.
is there any command i can use to check ssl config on 3750 switch?
Regards
Mahesh

Hi Mahesh,
Try running nmap against your switch: http://nmap.org/nsedoc/scripts/ssl-enum-ciphers.html
nmap --script ssl-enum-ciphers -p 443 <switch_name>
There is an open Cisco bug for this vulnerabilty:
https://tools.cisco.com/bugsearch/bug/CSCur23656
...which implies that this vulnerabilty is not fixed in any version of IOS!? If you are concerned, use the CLI and drop the HTTP(S) access.
cheers,
Seb.

QoS Questions for 3750 Switches

2x3750 switches are stacked and we are trying to simulate traffic congestion at the UTP ports by using Smartbit 6000C. The objective of the test is to see if the QoS setting works in reality even though we see from Wireshark that the packets are marked with DSCP for voice traffic.
Setup is as follows :
Smartbit<->Avaya IP Phone<->3750 switches<->6509 switch.
Please note that the configuration is set on the 3750 switch port as well as trusted on the Cat 6 switch port. However, when I set to continuous traffic with byte size of 64. Even though its a 100Mbps port, the Avaya IP Phone is already acting weird with hanged symptom. Just side note is that performing "show mls qos inter gi2/0/7 statistic" shows that data and voice traffic are marked on the different priority which seemed correct.
1) Is this the right way to test? If not, what should be the correct way?
2) The port that's connected to Smartbit is configured and it seemed that with the continuous traffic, even other IP Phones are hanged even though I have set Smartbit to hit on the IP address of the CAT6 Switch port. This is not normal right as this is supposed to be unicast traffic. Any idea what could be the reason?

Hello Brandon,
I understand your concern and how you want to test, but with the VoIP services you need to understand that there are 2 points (telephones if you want) involved. Your local one, where you might have taken all the necessary steps to protect and prioritize your voice traffic, and the oposite end which also need to have the voice packets prioritized.
Now, from your description, I understand that the packets (voice and data) marked correctly (I believe on C3750), but that's not enough. You need to use CBWFQ together with LLQ to give priority to the Voice traffic over data in case of congestion. Do you have such configuration? Can you show us some excerpt from it?
Next, during the testing, you said that your phone hang-up...where you in a call?
To respond to your questions:
1. The start is ok, but we need more details. You are pushing traffic from Smarbit, this is your local end, but where is the traffic pushed to (remote end), who is receiving the traffic?
2. In theory, you shouldn't have any impact over voice if links are 100Mbit, only if you have such a power packet generator that could fill 100Mbit. What do you mean by "This is not normal right as this is supposed to be unicast traffic"? VoIP is also unicast traffic...
I can see that you are determined to solve this issue, and this is OK as it will help you back with gained knowledge, but I have to warn you that troubleshooting QoS / Voice related problems may be more tricky than you think, as it will involve a strong know-how in these areas.
We will help, but you have to come back with more precise details.
Good luck!
Calin

Catalyst 3750 Switch

How many total Vlans can you create in Catalyst 3750 Switch ? I read a document about Catalyst 3750 Switch. This document is said that "Although the switch stack supports a total of 1005 (normal-range and extended-range) VLANs, the
number of routed ports". However, I am not sure. Can you confirm for me ? Thanks

this link should be of some help to answer your question.
http://www.cisco.com/en/US/products/hw/switches/ps5532/products_command_reference_chapter09186a00803ec324.html#wp1031710
HTH-Cheers,
Swaroop

3750 switches list of instances to monitor

Similar Messages

Maybe you are looking for