3750G - cannot access GUI on the wireless controller

I am not able to access the GUI of the wireless controller - If I console into the wireless controller I can ping the management IP address but if I console into the switch I cannot ping the wireless controller.
I think someone may have screwed up the configuration files - is there somewhere I can download the "factory" configuration from?

To recovery to factory default, you will need to be on the console of the controller, and reboot. Once you are at the user login prompt you can login with recover-config, this will reset the controller to factory defaults. Prior to doing that, hit the CLI from the console port, and issue the command show interface summary. Take a look at the VLAN assigned to the management interface. Then take a look at the switch, and look at Port-Channel 40, should be there by default fo for the port channel to the controller. Want you want to check for is, the native VLAN on the port-channel. This is a dot1q trunk, so if they are tagged the same on both sides traffic will get dropped. For example, if you are using 10.20.1.2/24 for the management interface and this is VLAN 20, then on the port channel you should have switchport trunk native vlan 20, and on the controllers management interface you would want to set the VLAN for 0, untagged. If you need to change this from the CLI of the controller, first issue the command config wlan disable 1, to shutdown the first wlan, then issue the command config interface vlan management 0, this will set the management interface to be untagged. Once you have done this, try to access the GUI again. Once in, you can make the same change to the ap-manager, if it is on the same VLAn as the management.
Steve

Similar Messages

Lightweight access-point joined the wireless controller but no radio channels

a customer wireless controller 2106 he use access-point AIR-LAP1252G-E-K9 the access point the leds indicate
etherner and radio is blinking green and status is green.
please help i am in the customer company now

The AP1252 has higher power requirements than some of the Cisco PoE switches provide. Depending on the switch you are plugging them into you will get enough power to power up the device and connect to a controller but not enough to power up the antennas. Options that can work include:
1) Removing one of the antennas if you are not gonig to use it (or as a temporary workaround to get some wireless)
2) Using an external power supply
3) Using an external inline power appliance system that supplies enough power (http://www.microsemi.com/powerdsine/ is one example).
4) Depending on the type of switch you are connecting to you may be able to upgrade code to provide a higher amount of power to the port. For instance, a Catalyst 6500 by default supplies 15.8 watts of power to a port. But if you upgrade the code to 12.2(33)SXH2? I believe you can get 16.8 watts of power and this is enough to bring up both antennas on the AP. But even then you don't have enuf power to run the upper N speeds - I think anything above 72 Mbps is unattainable.
Other AP models such as the 1140 have lower power requirements and may work better for you.

Manually add Access Point to 2504 Wireless Controller

We have a 2504 Wireless Controller and it works great!
We currently have 6 Access Points (Aironet 1252) connected.
We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.
Now, I have been assigned to add another Access Point, but at a remote site.
The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.
We have plenty of licences on our current Wireless Controller.
Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
If so, how?
Thank you!
Bryan Smith

Here are some links
AP join
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
FlexConnect
http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html
Sent from Cisco Technical Support iPhone App

When we purchased our mac two years ago, we set up the iCloud account. this past winter I created a new iCloud account thinking I was changing it. I now cannot access anything on the old iCloud acct and my computer hasn't been backed up either in awhile

when we purchased our mac two years ago, we set up the iCloud account. this past winter I created a new iCloud account thinking I was changing it. I now cannot access anything on the old iCloud acct and my computer hasn't been backed up either in awhile. How do i go back to that old account and delete it so that I can continue backing up on the newest account? I changed it because the original one I created an iCloud account with is a yahoo account email address and I am deleting my yahoo account for being compromised too may times.

Well, you can go to Manage your Apple ID and change the password if you can answer the Security Questions:
Apple - My Apple ID
If you cannot remember the Security Questions you can contact iTunes Support to reset them for you:
New iTunes Support - US and ww
Once you get your password reset and you can access your account info on Manage your Apple ID, you can change your ID. You won't be able to use the same email address that you are using for the new ID unless you change that one to something else. But, if you can get back into your old ID and change it to a new email address, then you can go on using that old ID, and just manually move the iCloud stuff you added to your new ID back onto the old one. Most of the stuff (like Contacts, Calendar, Notes) can be added by logging onto https://www.icloud.com on your Mac and doing it that way (it is a lot simpler when you have an actual keyboard in my opinion)
Hope this helps you to sort out the two ID business. If you have any questions, please post back!
Cheers,
GB

I transferred my CS 6 applications to a new computer, and now cannot access Illustrator, only the trial version of creative cloud. How can I access the software I own?

I bought a new Mac Pro, transferred my CS software to it from my old Mac Pro, now I cannot access Illustrator, only the trial cloud version. How can I use the software I have already purchased?

Just to clarify, in case this helps anyone. I transferred the whole CS 6 suite using Apple's migration assistant, and the only program in the suite that could not be accessed except through the trial cloud version was Illustrator. After over an hour on the Adobe support chat, it turned out that I needed to follow the prompts to purchase the cloud version, then type in the serial number for my CS software at a certain point in the process. There you go.

My IPad screen is frozen with a message stating that the IPad has not been backed up to the ICloud for 7 weeks, this is not correct.I cannot get the messageto clear and cannot access any of the other icons; is there an emergency reboot process?

My IPad screen is frozen with a message stating that the IPad has not been backed up to the ICloud for 7 weeks, this is not correct. I cannot get the messageto clear and cannot access any of the other icons; is there an emergency reboot process?

Have you tried resetting your iPad?
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10-15 seconds).
No data will be lost.

TS4062 I cannot get a WiFi signal, which means that I cannot access all of the other features on my ipod. Is there anyway I can access all of the other features without Siri or WiFi?

I cannot get a WiFi signal, which means that I cannot access all of the other features on my ipod. Is there anyway I can access all of the other features without Siri or WiFi?

Hi. The two user tips both describe a sequence of steps that should get your library from the point where it threatens to wipe data from your device to where it is syncing normally, while recovering as much information as possible. It may still be necessary to wipe and reload the device but this should only take place once all the data that can be recovered has been recovered.
Doing step 1 of 8 and then complaining things aren't the way you want them to be yet strikes me as premature...
Since you appear to have all your media content, and we are discussing an iPod classic, not an iOS device, the main worries are already taken care of. What's left is ratings, playcounts, playlist membership and checked status. Since your device holds only part of your library at best you could only recover the missing data for the content that is on the device using third party tools.
Recreating the previous checked/unchecked status of every track in your library from where you are now may not be that easy. Syncing with selected playlists has many advantages, one of which would have been that you would have a named playlist that could have been retrieved by 3rd party software if you had used this method.
You haven't explained what caused your problem in the first place, but if you have a Previous iTunes Libraries folder holding old copies of your iTunes database (generated with each iTunes update) then it would be possible to restore the most recent of these and then update the library with any changes in your media folder.
BTW Apple doesn't offer free support for this kind of issue with iTunes.
tt2

Have iPad Air and Apple Wireless Keyboard. Can I access emoji from the wireless keyboard?

RE: iPad Air and Apple Wireless Keyboard
HI, I have an iPad Air paired with an Apple Wireless Keyboard. Can I access emoji from the wireless keyboard?
Thanks for any help on this subject!

Eureka! I kept searching and found the solution. So, if anyone wants to know here is the solution: press fn and the up arrow on F Keys (top) row (it's the one all way to the right. The iPad keyboard will then pop up on the iPad and from there you can access the emoji keyboard.

I use premiere and cannot access all of the transitions, they are grayed out. Why is this?

I use premiere and cannot access all of the transitions, they are grayed out. Why is this?

Maybe you have them "filtered" at the top of the FX Window (Icons)

My Acer Switch 12 keyboard has quit functioning and I cannot access Bluetooth through the settings.

My Acer Switch 12 keyboard has quit functioning and I cannot access Bluetooth through the settings. Please help

fdbiker,
Depending on what your warranty period still looks like I would suggest service.
Here is the link to set up repairs online, or you can chat online with a technician (available 24/7)

When I turned on my phone, it has mega fonts and I cannot access anything including the settings to turn off find my phone for restoration

when I turned on my phone, it has mega fonts and I cannot access anything including the settings to turn off find my phone for restoration

Double tap with three fingers on the screen and the zoom feature will be disabled again.

Access points As a Wireless Controller

Dear
I need a proposal for the fully meshed 9 wireless access points. In which
One can behave as wireless controller
Dual Radio connectivity
Poe on each AP or extra port of Ethernet
Warm Regards
Hassan Sarfraz Ali

I see what you're asking, Since virtual controller concept is evolving and no one wants single point of failure i.e., single controller for smaller deployment and remote offices, what you're asking is quite logical for local and flex mode. For Mesh, considering awpp convergence may not suite is what i believe.
Until 7.3 Cisco don't have this feature. Whatever you're looking could be what Cisco's future making or already work in progress, you may want to check with Cisco via TAC.

I also cannot access part of the App Store, I have been trying to down load a magazine app, it has been trying to connect but it has been taking a long time. Also since I did my last update I have lost the ability to face time, I also cannot open iPhoto's

Since my last update on the newest version iPad I have not been able to download a magazine app that I have a subscription for as well I cannot open iPhoto's or video. When I go into settings and go down to where iTunes Mail etc are it freezes my I pad and I cannot access these. Is there a apple system problem? This has been going on for over a week now.

For FaceTime try the troubleshooting advice given here:
http://support.apple.com/kb/ts3367
Also try resetting your iPad:
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10-15 seconds).
No data will be lost.

Managing remote C800 with the wireless controller

We have a number of regional offices throughout the country with a C800 as the Internet facing router and it is also our wireless.
We have a Cisco wireless controller in the Data Center an we need to manage\monitor all the C800, but the problem is that those remote sites
are not VPN'd nor part of our WAN network.
Which setup do you
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
recommend:
1) 1) WLC to monitor the C800 using its public IP address
1) 2) Create a VPN tunnel from each of the remote sites to our data center and only allow wireless to go through for mgmt purposes
anany other options?
T

First question is which 800 do you have ? there's like 20 different versions out there.
If you talk about WLC, I would suppose you have something like the 880 ?
I'm afraid the WLC will need the internal AP ip address. So you would need to do so reverse nat to direct public ip address tarffic on capwap ports to the internal AP.
This or the VPN tunnel.
Nicolas
===
Don't forget to rate answers that you find useful

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

3750G - cannot access GUI on the wireless controller

Similar Messages

Maybe you are looking for