3750X 10G uplink interfaces in access mode

Hi all,
just asking, any one knows if its possible to configure an 10G interface from a network module in a 3750 X switch in ACCESS MODE?

Hi Hans,
As mention you can use Tengig port to connect to Server same configuration as normal access port on Gig interface but check SFP transceiver at switch whether it is compatible with server end SFP.
Also if your server is is connected to Tengig port there over Subscription issue on uplink if it is 1 gig link.
Br.
Mohseen Patel

Similar Messages

Cisco 3750X -- 10G uplink - Can be used as access port?

Dear All,
I have small question, I am planning for Cisco 3750X with 10G SFP+ service module. I want to know that whether it can be used as Access Ports connecting to server as this is mostly used as uplink port.
Thank You,
Abhisar.

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Well if you want to connect anything with 10g to a 3750X, you're limited to using a module with 10g ports.
Other than 10g capability on some module cards, something to note, the module ports, I believe, are supported by larger buffers (including the gig module ports).
As the others have noted, you can use any port for any purpose. However, if you connect a server to a 10g port, be aware you might start to see drops on your other host (gig) ports as the server will now be able send faster than the host port can receive data. To minimize this, you might either disable QoS on the switch (providing maximum buffers to all egress traffic) or you might need to tweak buffer resource settings (the default settings often drop some packets, when there are bursts, of default marked packets).

User interfaces to access Content services...

I am using the following user interfaces to access content services:
1) Web UI
2) Oracle drive
3) WebDAV with Windows XP
But in the oracle content sevices data sheet which I downloaded from the Oracle site, its given there is a rich WebUI with dynamic tree structure with drag & drop features. I want to know if this exits? If yes, I want to know how to access that and work with it. Does it need any downloads or configurations to be done.

Hi
I have selected "Accessiblity mode" button to launch the web interface. Now for this user even if i select the "Lauch" button. it still shows up the interface of accessibility mode. Is there any way I forced the user to switch back to the Lauch button interface mode.
Regards,
Navin

Message interface in synchronous mode but run in asynchronous

I try to use SAP-XI in synchronous mode with JDBC to JDBC connection.
A 'Outbound' message Interface under synchronous mode is defined for
sender while an 'Inbound' message interface under synchronous mode is for
receiver.
In the sender communication channel, a "select" SQL statement is
placed for getting data via JDBC.
For inbound interface, a stored procedure is triggered and it will
return 2 paramaters.
From transaction SXMB_MONI, I found that the message was in 'asynchronous'
mode and I don't know how to collect the 2 output paramters.

Dear all,
Upon all your suggestions, my testing have a big jump with below results but still have some problem
In the sender communication channel, a "select" SQL statement is placed for getting data via JDBC. It works.
For inbound interface (receiver), below stored procedure was actually triggered and it DOES return 2 paramaters.
<?xml version="1.0" encoding="UTF-8" ?>
<ns0:MT_t1 xmlns:ns0="http://xxx.xxx.hk/zxxxx/jdbc">
<update>
<storedProcedurename action="EXECUTE">
<table>LIBRARY.PANSYTEST</table>
<TRNX_TYPE IsInput="TRUE" TYPE="CHAR">001</TRNX_TYPE>
<TRNX_NO IsInput="TRUE" TYPE="CHAR">101048</TRNX_NO>
<OUT_TRNX_TYPE IsOutput="TRUE" TYPE="CHAR">001</OUT_TRNX_TYPE>
<OUT_TRNX_NO IsOutput="TRUE" TYPE="CHAR">101048</OUT_TRNX_NO>
</storedProcedurename>
</update>
</ns0:MT_t1>
Then I got the response message from the inbound interface
<?xml version="1.0" encoding="utf-8" ?>
<ns0:MT_t1_response xmlns:ns0="http://xxx.xxx.hk/zxxxx/jdbc">
<update_response>
<response_1>
    <update_count>0</update_count>
    </response_1>
    <OUT_TRNX_TYPE>001</OUT_TRNX_TYPE>
    <OUT_TRNX_NO>101048</OUT_TRNX_NO>
    </update_response>
</ns0:MT_t1_response>
This response message was mapped to below message type. I suppose this will be passed
to outbound system (sender) and run a SQL "Update ps_cu_pg1iawd set cu_retrieved_by = "ZCU_CUSIS"
cu_action_cd = 'P' where cu_trx_type = 001 and cu_trx_num = 101048"
BUT the table ps_cu_pg1iawd is NOT updated and NO error was found in SXMB_MONI.
    <?xml version="1.0" encoding="UTF-8" ?>
<ns0:MT_Response xmlns:ns0="http://xxx.xxx.hk/zxxxxx/jdbc">
<statement>
<PS_CU_PG1IAWD action="UPDATE">
    <table>ps_cu_pg1iawd</table>
<access>
    <cu_retrieved_by>ZCU_CUSIS</cu_retrieved_by>
    <cu_action_cd>P</cu_action_cd>
    </access>
<key_1>
    <cu_trx_type>001</cu_trx_type>
    </key_1>
<key_2>
    <cu_trx_num>101048</cu_trx_num>
    </key_2>
    </PS_CU_PG1IAWD>
    </statement>
</ns0:MT_Response>

How to create a calendar activity in accessibility mode ?

I didn't find any way to create a calendar activity in accessibility mode. Since it shows blank list of days in calendar component for a month.
It seems to be a bug in ADF calendar component. Please suggest if there is any alternate way to support this.
Thank you so much.

Timo,
From a reference doc of previous version of jdev/adf, it said :
http://www.oracle.com/technetwork/cn/java/calendar-091799.html
Expand the Data Controls accordion and drag the collection that represents the view object for the activity created above (FodCalEventVO) and drop it as a Calendar.
But in Jdev 12c.--cannot find the Create Calendar choice.
In jdev 12c can drag and drop a calendar component from the component palette, but do not now how to bind it to view objects.
Thanks.
BAO

Using TImed Access mode on Airport Extreme with other routers in bridge mode. Not working as expected.

I am trying to setup timed access mode on my airport extreme in order to limit the times devices can connect to my network, but I am having some trouble.
My setup is as follows Cable Modem ---> Airport Extreme ---> Netgear router
The Airport is running DHCP and the Netgear is in bridge mode. The only purpose of the Netgear is to provide a wireless access point for older b/g wifi devices. The Netgear is connected to the Airport by an ethernet cable from one of its LAN ports. All ip addresses are supplied by the Airport.
When I list a device mac number in the Airport extreme's timed access table it does seem to block the device if the device trys to connect to the airport's wireless service, but the device is still able to obtain service through the Netgear wireless service. I want the device to be blocked on both wireless networks. I thought this would work since all DHCP is on the airport. Why is the Airport allowing the device to connect when it comes in through the Netgear?
In this example the device I am trying to block is 5c:59:48:ba:28:d2.
Looking at the log on the airport I see the following entry when the device (when permitted) connects to the airport wireless
Nov 30 22:43:12
Severity:5
Associated with station 5c:59:48:ba:28:d2
If instead the device connects to the Netgear wireless I see the following log entry on the airport (this connection gets through even if the mac address above is listed as blocked on the airport)
Dec 01 10:46:29
Severity:5
Connection accepted from [fe80::223:12ff:fe29:acfe%bridge0]:54774.
It appears that the Netgear router (while bridging the network) is somehow modifying the mac address format in a way that the airport does not recognise it as the device to block.
What can I do to fix this?
Thanks.

The Netgear wireless server has control over what what devices are allowed to connect.
Unless you tell the Netgear what devices you want to allow to connect, it will allow any wireless device to connect as long as it knows the wireless network password.
IF.... .you were using two AirPort Extremes, and not a Netgear, the two Extremes would communicate to each other....so you would only have to enter Timed Access settings on one router and other AirPort would automatically pick those settings up.
But, even this was not the case until the last year or so when Apple updated firmware. A few years ago, you might have had 2 Apple AirPort Extremes on the network, but you still had to manually set up Timed Access on both devices separately.
Bottom line, you need to setup the equivalent of Timed Access on the Netgear router.

How to change Access Mode of HANA Stored procedure

Hi,
When you are creating a stored procedure as design time object, one of the option is access mode (either read only or read/write).
I understand read only is default setting in HANA DB, and unless you explicitly change the setting you cannot read/write using stored procedure.
My question is, is there way to change this setting, so I have option to choose either read or read/write when I create a stored proc?
Thank you.
Hyun

Hi Hyun,
Please have a look on this thread:
Create local temporary table in procedure
You have to enable sqlscript_mode to UNSECURE as mentioned by lars.
Then depending on whether you are specifiying "READS SQL DATA" it will act as a READ procedure else as a WRITE procedure.
Regards,
Krishna Tangudu

My external hard drive goes in to constant access mode and really slows down my computer

I'm using an external hard drive for time machine. After working for an hour or so the drive goes into a constant access mode and realy slows down my IMac. I look at activity monitor and everything looks good, no high CPU usage or memory issues. The only fix is to use the power button to shut down my IMac. After restart it works fine for a while.
If I turn off time machine the problem seems to not happen. I tried disk utility on the external hard drive and it says the dirve is fine. I change out external drives and the problem still occures. Any thoughts?

I didn't realize my profile stated otherwise.
Please check near the bottom of your original post above to see OS X (10.7.2). You might want to update that to avoid confusion and save some time in the future.
OK, please take a deep breath.
Apple does not officially support Time Machine backups to a drive at the USB port of the AirPort Extreme....likely because it is not reliable. You might want to review this Apple Support document to confirm:
http://support.apple.com/kb/HT2038
So, we are not going to be able to provide you with much assistance on that issue.
Some users seem to be able to make this work....some have some problems....and some (like me) who have tried this have nothing but problems.
Sorry, I can't help on this one, but maybe another user who has had better luck will post to provide his secrets.
The iTunes and iPhoto libraries and files are my only copies now. I moved everything from my Macbook to the external then deleted the originals.
Not sure if you have thought about this.
If you deleted the "originals", then your only copy of your data is on one hard drive. You have no backups if the drive has a problem.
A minimum backup plan would be to have a copy of important data on two different drives. When....not if...one drive fails, you have the data on the "other" drive.
You have no "other" drive according to the information that you have provided.
Further.....Time Machine backs up the changes on your Mac. At some point....you cannot know when.....Time Machine will pick up the change on your Mac and delete the iTunes and iPhoto data from your Time Machine backups.
The files might stay there a few months, or even longer. But, I have seen instances where the files were deleted within a week or two.
So my advice would be to only delete data from your Mac that you can afford to lose.

Accessibility-mode set to inaccessible and 508 compliance

Hi,
I'm using JDEV 10.1.3.3.0.
I've set accessibility-mode to inaccessible in adf-faces-config.xml in order to set the InitialFocusID on some of my pages. Does this setting mean that my application is not/cannot be 508 compliant?
Is there a way to use the InitialFocusID (or other way to position the cursor) and use ADF Faces automatic 508 compliance code?
TIA,
Dave

Hi,
ensure you use the correct version of JAWS. In the past I've seen things like this caused by the JAWS reader. If the problem still shows and you have a support contract, provide a test case and file a bug
My problem is when i use tab key from keyboard to navigate on the page the component highlights(dotted line around the component ) but it does not open the required popup.
This is because there is no setting in your page code that says that the popup should show when the component is in focus.
+<af:showPopupBehaviour popupId="alertPopup" triggerType="mouseOver" align="startbefore"/>+
+<af:showPopupBehaviour popupId="alertPopup" triggerType="contextMenu" align="startbefore"/>+
Frank

Accessibility mode FAIL

I want to love BB 10 OS & my Z10. I am proud to put my phone on the table with all the iPhone fanboys and let them know they are slavish drones! But I stumbled into a major design flaw today and I want to nuke my Z10!
Maybe I'm just nervous, but I must have pressed the Lock button 3 times. Like Dorothy in the Wizard of Oz clicking her heals. The next thing I know the phone is talking to me. Thus ensues 2 hrs of maximum frustration There is ABSOLUTELY NO SCREEN SUPPORT that tells me I'm in Accessibilty mode. A simple message: "Press Lock 3 Times to Exit Accissibility Mode" would have helped immensely.
The operation of the phone becomes100% inscrutible. I later learn that this mode is for the visually impaired. I would like to know what testing was done with people who needed this 'feature?' Close your eyes and tell me it helps! It only stumbles, stammers, fails to respond! I later learned with a call to the ever-helpful T-Mobile support people that a three finger swipe at precise angles, velocity and incredible accuracy has a PRAYER or reversing this mode. OMG! I was going to drive to a T-Mobile store or the hospital emergency room after the hara-kiri I was sure would be more humane than this devil spawn of a BETA FEATURE!!
PLEASE: make the triple lock press a DEFAULT OFF function for accessibility. If you are visually impared it would be a purposeful selection that would require assistance anyway. DON'T MAKE IT THE DEFAULT! And for heaven's sake make disabling/reversing it obvious. Who could possibly imagine that three finger swipes or triple clicks (seriously??) would be natural UI features?
I want to love BB, but this really crashes my party
Kim
Indianapolis

Pressing the power button three times enables Screen Reader Beta in Accessibility Mode, you must have also confirmed Confirmation Message (default On) to accidentally have gone into that mode.

Is there api function to change access mode and set a passcode to recording in meeting?

Is there api function to change access mode and set a passcode to recording in meeting?
When I'm trying to use "action=acl-field-update&acl-id=SCO_ID_RECORDING&field-id=meeting-passcode&value=MY_PASSC ODE" it just clean the password and do not set it or change.
And "action=permissions-update&acl-id=SCO_ID_RECORDING&principal-id=public-access&permission- id=view-hidden" do not work too.

There is not a specific API for doing this. This was discussed in the other Connect forum here, Adobe Connect User Community.
For you call I would make the second part differently. Instead of 'field-id=meeting-passcode&value=MY_PASSCODE' I would call 'meeting-passcode=MY_PASSCODE' and see if that worked better.

Command for: Access Mode for Result Set

Hi
Does anyone know if there is a command for "Access Mode for Result Set".
The default view for my characteristic in my query is "Characteristic Relationships".
I would like to have a command button for the user to be able to change the access mode to "Posted Values"
I have searched through all the commands but was unable to find this command.
OR if it is not available does anyone know the XHTML that I could enter into the web template.
Thanks in advance.
Ian

Hi
Does anyone know if there is a command for "Access Mode for Result Set".
The default view for my characteristic in my query is "Characteristic Relationships".
I would like to have a command button for the user to be able to change the access mode to "Posted Values"
I have searched through all the commands but was unable to find this command.
OR if it is not available does anyone know the XHTML that I could enter into the web template.
Thanks in advance.
Ian

How to display af:commandImageLink in accessibility mode

We use af:commandImageLink, and works all right. However, it does not show up in accessibility mode. Is it possible to display af:commandImageLink in accessibility mode?

I set shortDesc for af:commandImageLink and that text showed up as the link. So this problem is now resolved.

Accessibility mode

Hi, my son has enabled accessibility mode accidentally
The only thing the phone will now allow is swiping, how can i turn this mode off?
(I cant tap the screen to enter the settings menu to do it manually)
Thanks

After much hair pulling I discovered that you must triple tap when in accessibility mode
Still wasnt able to scroll when in settings menu but was able to use the search function to get to accessibility and then disable from there
Problem solved

Problem with Restructuring of the cube + IO access mode is Direct IO

Hi All,
There is a problem faced with the restructuring of the cube.
Application Name: Sample
IO Access Mode: Direct I/O
Operation peformed: Copying of Outline from one server (Development) to other server (QA). Performed verification of the outline & saved. And while closing the outline window, it was asking for the restructure and started restructuring of outline.
In this case, some exceptional files are created at the log directory & ABNORMAL SHUTDOWN of application is happening.
Below are the entries in the application log file:
*Restructuring Database [AtLaunch]*+
Essbase Internal Logic Error [7333]+
*Exception error log [E:\Hyperion\logs\essbase\app\Sample\log00011.xcp] is being created...*+
Exception error log completed E:\Hyperion\logs\essbase\app\Sample\log00011.xcp please contact technical support and provide them with this file+
RECEIVED ABNORMAL SHUTDOWN COMMAND - APPLICATION TERMINATING+
Please let me know the below information:
1.What will be happened to the Outline?
2.What is the reason of this kind of error and how to resolve this?
3.During the restructuring process, what will be happening if the access mode of application is in Direct I/O?

Exception error log [E:\Hyperion\logs\essbase\app\Sample\log00011.xcp] is being created...^^^You're on your eleventh crash? Not Good. Get that .xcp file to Oracle Support forthwith.
FWIW, some people swear by Direct I/O for its performance -- I was burnt, badly, by it in the past and never use it.
Copying of Outline from one server (Development) to other server (QA). Performed verification of the outline & saved. And while closing the outline window, it was asking for the restructure and started restructuring of outline.^^^You used the Migration Wizard? Did a Save As? Changed the density (my guess if BSO)? You did something that caused Essbase to do a restructure. A simple Save without changes shouldn't require that, I think.
Regards,
Cameron Lackpour
P.S. I have seen saves that do things like change BSO density (depends on whatever bugs your version has) and resulted in massive blocks. When Essbase tried to save -- KABOOM!
Edited by: CL on Apr 2, 2012 7:51 AM
Duh, if you're using Direct I/O, it is BSO.

3750X 10G uplink interfaces in access mode

Similar Messages

Maybe you are looking for