375o switch in stack, only 2nd and 3rd switch reboots

Hi,
In customer place we are having three 3750 switch and it was stacked and working fine. Few days back the in stacked switches 2nd and 3rd switches are rebooted continuously and found in the show version command as: Data TLB Miss Exception (0x1100)!.
From last 4 days we are not found any reboot. Please let us know any software bug is triggered to cause this problem, if upgraded please let us know the image to be put in all the three switches. I am sending the show tech output of all the 3 switches and show stack output.
Thanks in advance.
Regards,
Ram

This URL should help you:
http://www.cisco.com/en/US/products/hw/switches/ps5023/prod_release_note09186a00801b476a.html

Similar Messages

Video card to run 2nd and 3rd monitors cs5.5

Hello all,
I have a powerful system with multiple hard drives that I use to cut HD DSLR footage on in CS5.5. My GTX 570 runs my 1st monitor and my 9600GT runs the 2nd and 3rd monitors with great success.
1st monitor = timeline
2nd = bins
3rd = full screen preview (Highest quality preview)
The reason I use the gtx 570 to run only the first monitor is because it idles much higher and hotter connected to two monitors. (Disables the down clocking feature on the card when connected to multiple displays).
Well the 9600gt has died.
I don't want to spend alot of money here but I am not sure what video card I require for my 2nd and 3rd monitors. Keep in mind the 3rd monitor is the full screen preview.
I know premiere pro uses my 570gtx for the MPE but I have no idea how this effects (if it does at all) my 3rd preview monitor since I have had it plugged into my 9600gt.
There for I am not sure if I can get away with a cheap card like a $50.00 Nvidia GT 610 or do I need something at least equal or greater then my old 9600gt?
Thanks!,
Kieran

Thank you for the reply Harm. I have an x79 board with a 3930k @ 4.6ghz.
I will take that advice on board.. I might have to fork out a bit of extra money. Shame I only purchased the 570 gtx a couple of months ago!
Found this card....
Gainward GTX550Ti 1G DDR5 DVI HDMI
Internet Price:    $111.00
Barcode :
426018336-2050
GPU :
GeForce GTX 550 Ti
GPU Clockspeed :
900 Mhz
Memory :
1024MB GDDR5 192bits
Memory Clockspeed :
2050 Mhz
Pixels per clock (peak) :
N/A
Bandwidth :
98.4 GB/s
Ramdac :
400 MHz
PCI-Express 2.0
Cooling :
2-Slot Fan
Video-Features :
HDMI
Connectivity :
DVI-I + VGA
Would this be sufficient??
Thanks!!
Kieran

Adding a 2nd and 3rd Drive

I just added a 2nd and 3rd ata drive to my 450 MHZ tower. The motherboard had an open plug that said ata.
I plugged in the cord (strip) that came with the drive into the board and into the additional hard drives.
(fyi) I took both hard drives and strip from a working unix server.
I plugged in power to each.
I started up the mac. It shows the 1st drive on the desktop, but no others. Disk utility doesn't see the new drives either.
What did I miss?
Any help would be greatly appreciated. Thanks.
PowerMac G4 (AGP graphics) (version =2.9) Mac OS X (10.2.x) 9 GB SCSI
PowerMac G4 (AGP graphics) (version =2.9) Mac OS X (10.2.x) 9 GB SCSI

Hi omoriginals ,
Welcome to the Discussions.
Your computer can only mount two drives unless you add another ATA controller card in an empty PCI slot. There's one bus that has the ability to control two drives.
The additional drive and cable you installed will need to be removed. The other that you attached to the existing data cable needs to have its jumper set to "slave" and then attach it to the center position on the cable. The jumpers are small plastic and metal blocks that connect two pins located next to where the data cable attaches to the drive. There should be a diagram on the drive for the settings. Just set it, reinstall then format it with Disk Utility (in your Utilities folder).
John

Does the Ipad 2 3rd generation have the two cameras? What is the difference between the Ipad 2 , 2nd and 3rd generation?

Does the Ipad 2 3rd generation have the two cameras? What is the difference between the Ipad 2 , 2nd and 3rd generation?

All iPads have the camera except the very first generation. You can only buy an iPad2, the new iPad (4th gen) and the iPad Mini now. You can compare for yourself.
http://www.apple.com/ipad/compare/

Dunning 2nd and 3rd letter

Hi SAP Guru
How i can get Dunning 2nd and 3rd letters
I have getten dunning 1st letter but i am not able to get sencond and 3rd
what is the process , Thank you in advance

Hi,
Line items should reach minimum number of days, referring to the due date of net payment, to reach a certain dunning level.
In FBMP check you dunning interval. If line item has reached interval maintained for 2rd and 3rd level then items will not be dunned.
Also check dunning levels for your dunning procedure in FBMP.
If you find no problem with dunning settings then, activate additional log for the dunning run to identify exact reason for the problem.
Thanks!
Raju

Apple TV (2nd and 3rd Generation) - Home Sharing Not Working but Airplay Does

Hi everyone,
This has been a bit of a ongoing problem, so I'll provide a bit of background.
I am running a Mac Mini (Late 2012) Running Yosemite 10.10.1 as a media server running 10TB of Movies, TV Shows and Music off a NAS Drive. Running iTunes 12.0.1.26. Main hard drive is a 256GB SSD.
I also have 5 Apple TV's in the house, 2 are 3rd Generation (running iOS 7.0.2), 3 are 2nd Generation (running iOS 6.2.1).
The goal is to watch the TV Shows and Music through Home Sharing.
Home sharing works perfectly through the 3rd Generation Apple TV's, as does Airplay. I never have a problem with these. Mac Mini (or any other device for that manner) has no issues accessing the NAS.
The 2nd Generation Apple TV's are a continual source of frustration. They are connected to the network, can access the iTunes store, can accept Airplay signals from the Mac Mini, iPads, iPhones, etc. Can even detect the other (2nd and 3rd Gen Apple TV's). But frequently, when I try and connect to Home Sharing, I receive the error message "Cannot connect to Home Sharing", even though if I jump on the Mac Mini, I can airplay the content to that Apple TV just fine.
Is this just a 2nd Generation Apple TV Issue (to make us go an upgrade all our Apple TV's to 3rd Generation)?
I have completed the following troubleshooting steps, to no success.
1) Reset the Apple TV's (Multiple Times)
2) Sign out of Home Sharing\iCloud\iTunes Account, reset, and sign back in.
3) Restore the Apple TV to the latest firmware and set up again.
4) Test the device on Wireless and Wired Network.
5) Reset all network infrastructure.
6) Power Cycle the Apple TV's for 15 minutes.
7) Reset iTunes.
8) Sign out of Home Sharing\iCloud\iTunes Account in iTunes, Reset the Mac Mini, and Sign back in.
9) Reinstall iTunes.
10) Reset the Mac Mini and NAS.
11) Reformat the Mac Mini and update to latest operating system (Mac OS X Yosemite 10.10.1).
12) Try home sharing from a Windows PC (Windows 8.1, x64).
Literally out of ideas. Am I chasing a Unicorn on this one? Would love some help.
Thanks!

Good to know your Apple IDs are fine.
So I've been experimenting with de-authorizing and re-authorizing computers and devices and the symptoms you are experiencing are reminiscent of devices and computers unable to authenticate with Apple's servers.
What I would do is try de-authorizing and re-authorizing computers and devices to see if things return to normal. Start with the computers first. You can quickly de-authorize the computers by logging in to your iTunes Store account and using the 'Deauthorize All' button. After clicking the button wait a few minutes for it to propagate. You will know that the computers have been de-authorize when the Account Information page says "0 computers are authorized to play content purchased with this Apple ID." Other devices like Apple TV and iPads and such do not count on that list.
Once de-authorized, re-authorize them from the 'Store' menu in the iTunes app. You will know all three computers have been re-authorized when the Account Information page says "3 computers are authorized to play content purchased with this Apple ID." Now try and play your content with Apple TV. If it still doesn't work turn Home Sharing off on the Apple TV and then re-enable it using your Apple ID.
Hopefully this brings back your Home Sharing functionality.

What's the difference between 2nd and 3rd generation

PLEASE HELP! New Apple user and looking to purchase a used 2nd or 3rd generation ipod touch.
what's the difference between 2nd and 3rd generation?
apparently I am told that the 2nd gen does not have the capabilities of listening without headphone? and the 3rd gen does??

Hi maximumslowness - (great name),
The 2nd gen Touch has one internal speaker, so you can listen to it, (both left and right channels) without headphones.
However - it's a small single speaker and it is not very loud. It's not designed for quality listening (neither is the speaker on the 3rd gen as far as I know) and probably will not be adequate if there is a lot of background noise nearby.
One option is to drop the iPod (not literally!) into an iPod Docking station so that the sound can play out through a self-contained mains-powered amplified speaker, which will also charge your iPod. There are many on the market. On the bottom of the iPod is the 30-pin dock connector which can be used to feed the audio to a docking station. Another option is simply to use a cable to connect from the headphone socket to the audio input on any amplifier.
Yet another is to plug in a small fold-up style speakers, such as
http://www.amazon.co.uk/Portable-Folding-Speakers-iPods-Players/dp/B000A1QKNU/re f=sr_1_84?ie=UTF8&qid=1332326622&sr=8-84
or http://www.amazon.co.uk/Generation-Capsule-iPhone-Laptop-Speaker/dp/B002XNO7FQ/r ef=sr_1_6?ie=UTF8&qid=1332326656&sr=8-6
I've no idea how good the sound is, you'll have to judge that for yourself. The links are both to a UK store, but most countries will have a similar option.
I do not recieve any form of payment or compensatiion for the above links.
Message was edited by: the fiend

Itunes 7.5 freeze between 2nd and 3rd song playback of CD

Good Evening!
I am experiencing a problem with my itunes 7.5 freezing playback of a CD between the 2nd and 3rd songs of the disc in normal playback mode. What happens is that the 2nd song completes...transitions to the third song....plays a few seconds of the third while still displaying the info and time of the 2nd song and then freezes.....a spinning disc is displayed.....I am forced to force quit itunes.
I am at a loss to determine the root of this problem and turn to you fine folk for any advice in rectifying this issue. Thanks in advance for any and all advice.
Green Miler

This post is in the wrong topic!!!

On the 2nd and 3rd page of my ipod touch, none of the apps work You touch the screen and it starts to go, the doesnt. This started today. I've reset the ipod, but still not working.

On the 2nd and 3rd page of my ipod touch, none of the apps.work. When you touch the screen, they start to "go" then return. This started today. I have reset the ipod, but this still happens. What do I do now?

Ahh, looks like I remembered correctly
To the OP:
This is directly from the KB article lllaass linked to:
3. Install another app from the App Store
If all user-installed apps are not launching, it could be an Apple ID authorization issue. Download and install an app that isn't already installed on your device to reset this information.
Note: If you have installed apps using multiple Apple ID accounts, you may need to perform this step for each account.

I switched to the classic 'landscape' and when i reboot, it just stays at the greay screen, with the macintosh logo, and a blinking question mark. ive tried several methods of key combinations with rebooting etc.. i just bought this. please help.

i switched to the classic 'landscape' and when i reboot, it just stays at the greay screen, with the macintosh logo, and a blinking question mark. ive tried several methods of key combinations with rebooting etc.. i just bought this. please help.
I bought this off of craigslist with my christmas money, TODAY. i really need help, i have OS X experience from school, just not OS 9x. I need to reboot back to OS X asap. anything that may help is very appreciated. Thank You.
Chris.

Are you able to start up in Safe Mode?
http://support.apple.com/kb/HT1455?viewlocale=en_US
If this works you will see the normal desktop Once completely started up in Safe Mode, try to restart normally and go to Applications > Utilities > Disk Utility. Click on the top hard drive icon in the left sidebar and note the S.M.A.R.T. status at the bottom right of the pane. What does it say?
Select the named boot volume in the left sidebar, ("Macintosh HD" unless it has been renamed). What is the hard drive capacity and how much space remains available on it? Repair permissions on it.
See if you are able to do a little hard drive maintenance to help things out.

I have an original IPhone that can't connect to ITunes. I did a factory reset and restored to firmware version 3.1.3. Please note that both my ITouches (2nd and 3rd gen) sync to ITunes perfectly. However, the IPhone never connects. Thoughts?

OK, my original iphone has just completed a factory restore. It's connected to my laptop, and ITunes restored it to firmware 3.1.3. Now, I can't connect to the ITunes store. I get an error message every time stating connection timed out, or something to that effect. Well, both my IPod Touch 2nd gen and 3rd gen connect perfectly to ITunes, so I doubt it's related to proxy settings, firewalls, or anything of the sort (believe me, I've spend 15 hours researching this without an answer). So, is there a problem with the original iphone with version 3.1.3 syncing with ITunes version 10.5.1 (the most recent one)?
I would LOVE an answer as this is driving me crazy.
Thanks.

Mine had a SIM in it. Originally, when I took out the SIM and tried to restore it with nothing in it, it wouldn't work without a SIM card. So ... I took the SIM that was in that phone previously, put it back in and completed the system restore. I then proceeded to go through the process with AT&T of adding a data plan, which I did, and then it successfully completed the system restore. However, now if I run diagnostics on it, it will not verify ITunes Store. If I try to connect to ITunes store, I'll get the network connection timed out error I referenced earlier in this thread. I'm considering jailbreaking it and putting on an earlier software version. Your thoughts?

Any difference 2nd and 3rd 8gb?

I've asked this before but is here ANY difference between itouch
2nd gen 8gb and 3rd gen 8gb besides version update?

No, there were no hardware changes. Actually there is no "3rd generation" 8GB iPod touch, not as far as official Apple terminology is concerned. Some dealers refer to the 8GB with the 3.x OS as "3rd generation" but that's erroneous terminology.

Where to place 2nd and 3rd website's home directories?

In Os X Server 10.4.6, when we activated our first website (the default) it's home directory is /library/webserver/documents
When adding a 2nd and third website to host, should their home directories be children of, or siblings of the original Documents directory?
And when I create them, what's the best way to create them to ensure the permissions are correct?
And for that matetr, what should the permissions be if I'm not using Webdav, and using FTP or SFTP to allow webmasters to update the sites?
I want to be sure the new websites inerit the same features (like running php, weblogs, webmail as the original website.
Thanks!

>When adding a 2nd and third website to host, should their home directories be children of, or siblings of the original Documents directory?
There's nothing special about a web site directory (other than permissions). /Library/WebServer/Documents is just Apple's default suggestion.
However, if you store the other domains in subdirectories of /Library/WebServer/Documents then they'll be accessible under the first domain, which probably isn't what you want.
For example, if you create your second domain in /Library/WebServer/Documents/www.domain2/ then it'll be accessible as http://www.yourdomain.com/www.domain2/
Therefore if you're going to use /Library/WebServer, create siblings, not children of Documents.
>And when I create them, what's the best way to create them to ensure the permissions are correct?
Web content needs to be readable by the 'www' user, and directories need to be executable. This means you can either save your content as owned by 'www' or, more commonly, make sure it's world-readable, that way other users can create and edit the content while apache can still serve it.
>And for that matetr, what should the permissions be if I'm not using Webdav, and using FTP or SFTP to allow webmasters to update the sites?
The user in question would need write access to the content in order to change it, whether locally or remotely. As mentioned above this could be that the content is owned by the user, but world readable, and that's probably the commonest setup.

No more data to read from socket only in 2nd and 3rd database

Hi,
I'm developing an application for a client with three independent login modes, each one with an independent database.
I'm using the following products:
Oracle 9i database (9.2.0.6.0)
Oracle Content Management SDK 10g (9.0.4.0.0)
Oracle Workflow (2.6.3.0.0)
Oracle Application Server 10g (9.0.4.2.0)
In development, I've these products installed in x86 machines with Windows 2000. I've no problems and no errors.
In the client, I've the same products and versions but installed in a Solaris Machine and I've the following error ONLY when I use the second and the third login modes (not always, maybe only in 50% of the times I submit data in the application). In the first login mode I have no problems. The code for the different modes is essentially the same so I don't understand what is the problem. I don't have access to the client server so I can't make a debug.
The error is:
Caused by: java.sql.SQLException: No more data to read from socket
     at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:189)
     at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:231)
     at oracle.jdbc.dbaccess.DBError.check_error(DBError.java:985)
     at oracle.jdbc.ttc7.MAREngine.unmarshalUB1(MAREngine.java:746)
     at oracle.jdbc.ttc7.MAREngine.unmarshalSB1(MAREngine.java:705)
     at oracle.jdbc.ttc7.Oclose.receive(Oclose.java:105)
     at oracle.jdbc.ttc7.TTC7Protocol.close(TTC7Protocol.java:565)
     at oracle.jdbc.driver.OracleStatement.close(OracleStatement.java:848)
     at oracle.jdbc.driver.OraclePreparedStatement.privateClose(OraclePreparedStatement.java:351)
     at oracle.jdbc.driver.OraclePreparedStatement.close(OraclePreparedStatement.java:285)
     at oracle.jdbc.driver.OracleCallableStatement.close(OracleCallableStatement.java:876)
     at oracle.jdbc.oracore.OracleTypeADT.initMetadata(OracleTypeADT.java:579)
     at oracle.jdbc.oracore.OracleTypeADT.init(OracleTypeADT.java:406)
     at oracle.sql.ArrayDescriptor.initPickler(ArrayDescriptor.java:1023)
     at oracle.sql.ArrayDescriptor.<init>(ArrayDescriptor.java:137)
     at oracle.sql.ArrayDescriptor.createDescriptor(ArrayDescriptor.java:102)
I'm using oracle jdbc thin driver.
As data source class I'm using jdbc.pool.OracleConnectionCacheImpl.
Anyone have a clue what is happening?

Have you resolved this? I am getting the same error, but after restarting my webserver and re-establishing my connection pools it works(for a while). I need to find the root.
Thanks for any help,
Mark

How to stack a SG500 and SG500X switch?

Hi, I've been trying to stack three switches a SG500-28P a SG500-52P and a SG500X-28P - the SG500s stack fine, however when I added the 500x to the stack, the unit deactivated itself and took itself off the network - not good as it was the core switch!
Any ideas what's going on, are they using a different stack protocol to the others - I was just going for native and 5G ?
Firmware was 1.3
Many thanks,
Chris

Hi,
SG500 and SG500x only supports native stacking.
Native Stacking—A device is capable of joining other devices in native
mode with its stack ports to form a stack. All units in a native stack must be
of the same type (all Sx500 or all SG500X).
See the attachment
Regards
Moorthy

375o switch in stack, only 2nd and 3rd switch reboots

Similar Messages

Maybe you are looking for