3850. mac filter at wlan with wpa key

Hello
I want to get simple mac filter at certain WLAN with psk authentication
I have such at my home cisco881 - MAC-based ACL apply to the radio interface.
I don't find how to make MAC-based ACL at 3850.
And I don't understand how to use class-map type control subscriber (and match mac-address), for example, for such task, because they apply to interface, but now wlan.
Can somebody send me full working config or certain url with decision for such task?

subscriber mac-filtering security-mode {mac | none | shared-secret}
Example:
Device(config-sg-radius)# subscriber mac-filtering security-mode mac

Similar Messages

Mac filter not working with Airport Extreme

I setup my new AEBS and for whatever reason when I setup the Mac filter it still will let the desired user in with the key. I have both the wireless N and the wireless G (guests) setup and it doesn't seem to work with the G for sure, unfortunately I don't have any other wireless N capable units so I don't know if it works with N. I would assume that it would block all other Mac addresses if I select "No Access." Please help, and no I do not have any extensions of it, it's just the Extreme as the single wireless access point in our house with WPA security. Thanks!

I had the same problem. On the MAC access panel in Airport Utility, click on the default user and then use the drop down menu below and click no access. Any of the added IDs you have added you can still put 24 hour access and only those users can connect to the network.
The default is set for all access, so unless you change this, no matter how many separate IDs you add, it will let anyone on if they have a password.
I didn't figure this out for years, but now it works the way I thought it was working all along...

N91 Podcast client over WLAN with WPA-PSK - downlo...

Hi all,
I'm using a N91 (2.20.008) and the Nokia Podcast Client (1.00.3) to download podcasts via my home network (router Zyxel P-2602HW-D1A). N91 can fine see my network but the connection is unreliable on the N91. I have several laptops and it works fine for them.
What happens is that the podcast client will start to update all podcasts, but nothing happens all the small "circles" just hang. If I try to download one podcast it will sometimes work, but mostly the Podcast client will only download 2% and then hang. Each time I have to drop the WLAN connection and reestablish it to get the next 2%.
So for me it seems that the client waits and waits for something that doesn't happen or some weird loop is taking place.
Is there any fix for this?
N91: 2.20.008
Nokia Podcast Client: 1.00.3
Router: Zyxel P-2602HW-D1A
WLAN Encryption: WPA-PSK
- Chr

Ivan,
Ok, that makes sense. So yes, as far as I know, the logs are not super helpful when it comes to MAC filtering pass/fail, but you will find generic messages related to MAC filter events. Filtering for MAC is a layer 2 association-level event, so if a client does not pass, you will see an SNMP log message like:
Sun Mar 18 20:23:52 2012 Client Association Failure: MACAddress: Base Radio MAC: Slot: 0 User Name:unknown IP Addr: unknown Reason:Unspecified ReasonCode: 1
If they pass, then you will see:
Sun Mar 18 20:29:05 2012 Client Association: Client MAC: Base Radio MAC : Slot: 0 User Name:unknown IP Addr: unknown
If you are not seeing these messages, make sure you have SNMP trap controls turned on for Client association and association failure events:
I have done some more testing today and I am not running into the issues that you are seeing. In my setup, named clients can associate and unlisted clients are failing to associate. At this point I would recommend that you try upgrading your code to 7.0.220.0 or higher. My testing was done on 7.0.220.0.
Justin

WLAN with WPA-PSK on E61

Hi,
when I try to connect my E61 to my wireless home network, I get prompted for the WPA key and it works fine. But the key doesn't seem to be saved bc the next time around I am again prompted to enter it. It's a 64 digit key. Is there maybe a certain limit to the number of characters up to which a key can be saved?
Regards,
hendikoischnur
IT will paint our future - either green or black
* ecosia, the eco-friendly search engine (powered by Yahoo/Bing/WWF);
* Searching for pics online? Try ecocho.eu or treehoo.com
* For those who don´t want to miss Google: Try znout.de - it´s Google running on green energy
* CO2-free chatting: Try Jabber-server.de (running on 100% waterpower)

Hi,
slight correction: It doesn't work at all! I enter the key, but when I leave that particular submenu with "Back" and go in again, the field where the PSK should be is blank again and when I click "Web", the phone automatically tries to connect, but tells me "invalid key" after a while.
Regards,
hendikoischnur
IT will paint our future - either green or black
* ecosia, the eco-friendly search engine (powered by Yahoo/Bing/WWF);
* Searching for pics online? Try ecocho.eu or treehoo.com
* For those who don´t want to miss Google: Try znout.de - it´s Google running on green energy
* CO2-free chatting: Try Jabber-server.de (running on 100% waterpower)

Is router pin number the same with WPA Key?

I am trying to find out what my WPA key is,
but I found router pin number instead of the wpa key.
Please somebody kindly tell me it is the same or not.
Solved!
Go to Solution.

Hi Veeton,
I agree with @VALETLINKSYS. The WPA key is the same as the passphrase or you can click on the wireless security sub-tab for a better view of the router's wireless security settings.

New 2008 Intel Mac CS3 and Actions with F keys

I just upgraded from my old ppc mac that was running Tiger and CS3. I have a new Mac Pro 2008 running Leopard and CS3. I have a number of Actions that are assigned an F key that I cannot use because they are corresponding to the system function keys. Does anyone know how I get the use of my F keys back in CS3.

Try this: open System Preferences, Keyboard & Mouse, and in the Keyboard Shortcuts section turn off what you want. I have them all turned off except the Screen Shots.

Mac Pro only booting with option key down

I have an 8-core mac pro that is great except for some odd booting issues. I have 3 internal drives, one with OSX 10.4.9 on it, the other with just files and the last with windows XP. I also, at times, have USB drives (or an iPod) plugged into the mac. When I restart, even if I have selected a boot volume in the startup settings, the machine will just go black. Sometimes it will play the startup chime multiple times, other times only once or not at all. The only way to get it to boot up into osx or windows is to hold down options. Even then, it only seems to work if I unplug all external drives from the machine. Any ideas whats going on or how I might fix this?
Thanks!

If you remove all of your USB/FireWire devices will your start up issue go away. What about resetting PRAM…
http://docs.info.apple.com/article.html?artnum=2238

Connection to WLan failed (WPA (2) Password)

Good evening
We have got a MacBook Air since July and have been able to connect it to our privat WLan (running since years, connects 2 Iphones, 2 iPads, several Windows 7 machines and smartphones without a problem). Since this week I can't connect it to our WLan. The WPA (2) password has capital characters, small characters and numbers.
- Is it still a problem to connect a MacBook to a WLan with WPA(2) password with capital characters? (found in different foren as solution for this problem some years ago)
- Was there an update of the software that causes now problems?
Where can I find the operation system version? It is our first MacBook...
Thanks a lot
Matthias

IOS 5.1.1 should not have affected your WiFi connection, however, if you are now having problems try:
Try Settings -> General -> Reset -> Reset network settings

Problem with connetction to wrt54g2 via wireless connection with WPA/WPA2 & wireless MAC filter

Hello,
I'm Alexey from Novosibirsk, Russia.
I have a problem with connection to wrt54g2 from my DELL D630 notebook via wireless connection. When I setup WPA/WPA2 in wireless security and wireless MAC filter I can't connect from notebook to WRT - in Windows I see that dynamic IP address from WRT is not assigned. When I switch off security mode to disable always OK, but I need a wireless security between DELL and WRT.
Connection via cable Ethernet port is OK.
Can You help me?

Have you tried the different laptop...?
Download 1.71 MB the firmware for WRT54G2 v1 and reflash the router's firmware.After reflashing/upgrading the router's firmware,reset the router for 30 seconds and reconfigure the router from scratch.

E1000: Lost WPA key with Samsung TV

After entering my WPA key into my Samsung HDTV (UN46D6050TF), I am able to connect to the Internet. However, after turning the TV off then back on, the WPA key is lost at the TV. Samsung replaced the main board in the TV but the WPA key is still rejected by the Samsung TV (they also replaced the WiFi tranceiver). All my other wireless devices connect and reconnect fine and Samsung claims not to have similar reports from customers using other routers.
Have others experienced the same or similar problems? Are there settings to the router (e.g., AP Isolation; CTS Protection) that might be at the core of the problem? Would specifying the TV's MAC address be a possible resolution?

If all the other wireless computers/devices are able to connect with the same network key then I think your router is working fine.
Check the wireless settings on your router.
Connect the computer to the router with the Ethernet cable. Open the setup page of the router and go to wireless tab. Click on wireless MAC filter sub tab and make sure that it is disabled.
AP isolation keep it on disabled.
You can also try to create a new wireless network and see if that works.
Open the setup page of the router and go to Wireless tab. Change the wireless network name SSID to create a new wireless network. Change the wireless channel to 11. Save the settings.
Go to Wireless security tab and enter the password for your wireless network.
Now try to connect to the new wireless network on your other wireless computers/devices. Try to connect to the new wireless network on your TV.

How to change the presets in pop-up menus (CS6 or CR 7, example Photo Filter) with arrow keys?

How to change the presets in pop-up menus (CS6 or CR 7, example Photo Filter) with arrow keys an see at the same time the changes on the photo?
It worked under Windows, now I use OS 10.8 and have to apply a preset with a click or Return button but after that the pop-up menu close so I have to open it once again to change a preset. Please help. Thank you!

The filter panel is a shortcut for the content panel and it only effects the content of that window. So if you have a folder it will only see this as a folder and not with its content. (a Stack behaves about the same, being different in only counting the first file in the filter panel criteria but not what is in the stack itself)
You have a view work arounds, first is use menu view / show items from subfolders (this can take some time especially if you have not used caching before on this content) and this builds visible thumbs for all content and that can be used for filtering.
Or use the find command (Edit / find) and inhere specify the source and fill in the criteria include subfolders and this will give you the correct result.
When you create a smart collection the find command also pops up given you the same opportunity to get the results in a collection, but since a collection is only a bunch of aliases referring to the originals you might be a bit careful with editing and deleting.

Display the second report as modalform and filter with primary key value of first report when you click on first report column link

Hi All,
I have two reports.
1. order report
2. order detail report
when you click on the order report column it display the order detail report as a modal form.
i was done below steps.
1. In page header i was written the below code
<link rel="stylesheet" href = "http://ajax.googleapis.com/ajax/libs/jqueryui/1.7.2/themes/
redmond/jquery-ui.css" type="text/css" />
<script src="http://ajax.googleapis.com/ajax/libs/jquery/1.4.2/jquery.js"> </script>
<script src="http://ajax.googleapis.com/ajax/libs/jqueryui/1.7.2/jquery-ui.js"> </script>
<script type="text/javascript">
$( function() {
$('#ModalForm1').dialog(
autoOpen : false ,
width :470,
height: 500,
resize :false,
function openForm1()
$('#ModalForm1').dialog('open');
function closeForm()
$('#ModalForm1 input[type="text"]').val('');
$('#ModalForm1').dialog('close');
</script>
2. order report.
3. order detail report
select * from order_details where order_id = p_order_id;
region header
<div id="ModalForm1" title="Ordered Items" style="display:none">
<p class="msg"></p>
footer
</div>
4. created the hidden item in order detail report.
5. in order report column attributes i was given link like below.
javascript:$s('p_order_id','#order_id#');openForm1();
when i click on the order report column link it passing the row primary key value to hiddent and open the report as modal form. however it is not filter the report with hidden item. it showing the no data found.
problem is hidden item value is not submitting. once we submit that value it showing the 2nd report with filter data.
can any help me to achieve above requirement.
apex: 4.2
oracle 11g
Regards,
Vijay.

Vijay,
Issue 1: Your usage of $s() JavaScript API seems to be wrong. For the first parameter, you need to use the name of the hidden page item and not p_order_id.
javascript:$s('P1_ORDER_ID','#ORDER_ID#');openForm1();
Issue 2: Seems like you are not setting the hidden page item's value in session state. Assuming your hidden page item is called P1_ORDER_ID, Under "Region Definition" tab of your "Order Detail Report" under "Source" tab, for page items to submit, enter the name of the hidden page item P1_ORDER_ID.
Thanks!
JMcG

802.1x peap mschap v2 with MAC Filter + IP Address Permanent

Hi my name is Ivan, i have an issue
I have one cisco wlc 5508 with ios 7.4.100 with a ssid is working with 802.1x peap mschap v2 with mac filter, and I need configure in the web page of the WLC Security > Mac Filter, a MAC and one IP Address permanent to the users.
I have a service dhcp into the wlc to this profile.
This configuration works fine for 3 or 4 days. At the fifth day , my users renew the ip address, and they can not surfing to internet, because in my firewall i have a policy to the users with exactly ip address, for example.
MAC Filter - IP Address A - UserA
My policy say:
PolicyUserA - Internet
Please, i can establish an filter mac associate to one ip address permanent to one user, when service dhcp in the cisco wlc is active?
I possible to do it?.
How can i do it?

Hi Ivan,
You can not map the mac-ip address pairs on the WLC DHCP.
The WLC has a limited DHCP server functionalities. You better to use an external DHCP server with full functionalities and then you can configure the DHCP server to provide the same IP address everytime to each client in your network.
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"

Satellite A100-003 WLAN connection timeout(with WPA-PSK)

I have a Satellite A100-003 notebook with preinstalled Windows Vista.
When I try connect to my router with WPA-PSK (TKIP) I have error:
Wireless authentication failed because of a timeout.
My notebook and router configurated correctly!! I installed new intel drivers for 3945ABG chip.
WPA2-PSK and WEP work fine.

Hi
The same happened on my old notebook.
I was not able to establish the WLan connection for longer than 1min with WPA encryption.
I have downloaded the newest Atheros driver and updated everything.
Everything works fine with WEP but not WPA.
Then I have disabled the Windows own configuration option and use the Atheros client utility. Now everything works fine!
I would recommend using the Intel Proset utility and check all possible settings!

How can i connect the mac with internet key?

how can i connect the mac with internet key?
I try but it tolds me that I haven't the javaruntime...

I try, but to run javapreferences computer told me that I must have a Java runtime... thankyou

3850. mac filter at wlan with wpa key

Similar Messages

Maybe you are looking for