3D rage wireless - illumination settings

Hi, I have the tactic 3D software and can save myself profiles/settings with no problem. But I can't seem to save the illumination timer settings. I want it set to 1 minute but every time I turn the headphones on they've reverted back to 'never'. What am I doing wrong?

Hi Niko,
Thanks for your message and informing me about your experience.
As you've already contacted Support, I will let them handle your matter. Unfortunately, there was no content/problem description in your email; I have forwarded your post here so that they understand the issue before they reply to you.
Cheers,
Colin-CL

Similar Messages

  • Sound Blaster Tactic3D Rage Wireless Firmware update fail

    Hey guys,
    As the title says, I have a bit of a problem. I just bought the Tactic3d Rage Wireless headset, and decided to update the firmware as I like to have the latest drivers when I get started on new hardware. So I update the transmitter while the headset was turned off. No problem.
    Then when it came to the headset I removed the transmitter and plugged the headset directly to the computer and started the appropriate application. At the end of the upgrade it said it failed to load the system after the new drivers was installed or something similar, and now it's just there flashing blue all the time. It doesn't respond to anything, and if I try upgrading the firmware again it says it can't find the headset.
    So I'm wondering A) Did I do something wrog here? and B) How do I fix it? Is there a way to restore the factory settings of the headset somehow?
    Please help! Thank you in advance.

    Hi guys,
    In an effort to centralize similar topics within our forum threads, I am closing this thread.
    Kindly post on the centralized thread (link below) for your concerns/ solutions to this particular concern:
    soundblaster tactic3d rage
    Cheers!
    Philip-CL

  • Unable to change wireless security settings on WRT54GS v5.1

    I'm using a WRT54GS v.5.1 with the latest firmware (v1.50.9).
    Set this up this weekend - all was fine until last night when the router stopped broadcasting the signal. I've reset the modem countless times and powered it down and back on again.
    The router is now working fine - but I'm unable to change any of the wireless security settings. When I try to change the setting under Wireless > Wireless Security to WEP, it just jumps back to Disable and no changes can me made. Same situation when trying to enable a Wireless MAC Filter?
    Any ideas? I don't want to use the router without any security in place!

    you can try to upgrade the firmware of your.
    try this link :
    http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=557&p_created=108421...
    make sure to select the correct model and version of your router. if you cant see the model # of your router as one of the downloads, you will need to have the router replace (hope you'll not).
    hope this help.
    ~ lyf_R_foeittee ;o) ~~

  • Tactic3D Rage Wireless Constantly Turns Off while Charging

    I got the Tactic3D Rage Wireless a couple of years ago and it has had many problems from the time I received it. I eventually got the others fixed, or mostly fixed, but this one has been annoying me increasingly in the past few months.
    The headset not only rapidly connects and disconnects with Windows 8 (I think it is a problem with windows and not the headset for this one), but it also turns off the second I turn it on while charging. This makes the headset completely useless when I am charging it. This would not be as bad, but now the headset will not actually charge when it is on its charger. After it "charges" for a few hours, I take it off of the charger and I immediately begin to hear the beeping, notifying me that the headset is low on battery.
    I finally made an account on these forums after a couple of days failing at searching for this problem with others so now I am posting this. Help is greatly needed for I don't want to be forced to spend more money on another headset if I can get this one fixed. Please reply with any questions I have not answered, and have a good day.

    Hi Logo594
    You may want to refer to this article, specifically the last paragraph of the article regarding charging.
    http://support.creative.com/kb/ShowA...spx?sid=111092
    You also mentioned that this headset is at least a couple of years old, so it is possible that the battery
    does not hold its charge well. If this still does not work, You may contact Support here.
    Cheers,
    Colin-CL

  • Best Wireless Security Settings-WRT54G Linksys Router

    I've been running into problems attempting to set the wireless security settings for my router and then trying to connect to the internet from my iBook. As long as I enable SSID broadcasting I can find my router but the problem starts when I enable the security settings. The iBook will then ask for the password and nothing I've inserted works??? I'm at a loss. I've given up, those sorts of brickwalls can do a number on your head--major headache this weekend..so I will try again tomorrow. I thought the passphrase is your password--the only thing that I haven't tried (after searching the forums here) is putting the $ in front. Does anyone have this particular router that can give me some suggestions (in basic, simple terms please) that can help me get started on a good security setup so that I won't be scared someone in the neighborhood (as I've read previously) is scanning and can log onto my internet connection. Thanks!
    iBook G4   Mac OS X (10.4.5)  

    Why in heaven would you want WEP to secure your network when you can have WPA which is more secure and doesn't have this kind of problems???
    With the right tools (available free on the net) you can crack almost any WEP protected network in less than a day (I have done this with my friends to prove them how weak WEP is).
    So imagine you set your WEP protected network, a neighbor crack it and use it, all of this while you CAN'T use your own network.
    You should try WPA, good luck...
    BTW: I have the same router, with WPA and SSID broadcast disabled.
    Message was edited by: CD5VS

  • Cant hear any audio from Sound Blaster Tactic3D Rage Wireless headset

    after getting the Sound Blaster Tactic3D Rage Wireless headset i red through the booklet inside and saw that i could download software for it so i went to the address it gave me and downloaded the firmware for windows and after it was finished and i had restarted my computer the headset and USb connector would both flash nonstop. as well as this i cant hear any audio from the headset. help me if you can

    Just discharge it and then charge it. Should work then, and never ever try those firmware updates they are the terrorists of these headsets

  • Soundblaster tactic3D rage wireless problems

    Hello so today i got this new headset Soundblaster tactic3D rage wireless, and after charging for 8 hours i plugged the power cable out, and inserted the usb adapter.
    Everything worked fine, the sound was good. i then decided to go and download the drivers etc.
    Then i tryed to install the firmware update, and i got an error where it said that it failed.
    After that, my headset was completely dead, its constantly glowing red, i cant pair it with the usb adaptar, and i have tryed everything. Cant turn the headset off at all.
    I have lookd around these forums but didnt really find any good answers on how i could fix this.

    apparently you need to get it replaced, as the failed firmware bricked it. Only answer I found out so far. That or maybe getting a kind soul with the previous firmware to give it to you might get it working again.

  • Tactic 3D Rage Wireless V2 connecting issues

    "There is no supported audio device available" it says.
    I've already done the initial 8 hours of charging and I've used them for 2 days of slight gaming before they ran out of power. Now that I was going to charge them via USB ports (Tried both 2.0 and 3.0 -USB ports) it just didn't respond to anything. No red blinking light, no nothing. And as I mentioned, it only says "There is no supported audio device available" which really pisses me off. I've reinstalled the one and only driver for my headset/operating system 3 times, which also pisses me off really good. So basicly, it worked the first time i charged it, not the second time. It's a brand new headset, got it last wednesday, which pisses me off the most.
    Help out this pissed of guy would you?
    Kind kind kind regards Alfons ( )

    Originally Posted by Afhene
    The headset is now detected, strangely since i haven't touched the wireless transmitter at any point. Still, it just doesn't charge. I remind you once again. I charged it once.. the initial 8 hours was painless. I do have a clue for you though. When I restart my computer with USB-charger being put, it says " keyboard: 2, mouse: 2, hubs 2..... shutting down in 15 seconds" and it shuts down as promised. I remove the USB-charger from the USB-port and it does the regular start up. I've tried every single USB-port (I've got 10 of them) and I am still pretty pissed of to be honest. I'll keep saying that until it gets solved, take no offence Creative Employees (unless you've developed this ga***ge).
    EDIT: Not sure if it's entirely connected though. Playback Devices sounds setting says "No jack information available" when I look closer into the headset's properties in there.
    Somewhat kind regards Me ( )
    Hi Afhene,
    There is no jack information available for the Tactic3D Rage Wireless. Please avoid charging the headset via a powered USB hub. Connect the headset direct to the computer's powered USB port.
    Since your headset is now detected, you can launch the SB Tactic3D Control Panel and look for the battery level indicator of the headset after it has been paired to the USB wireless transmitter.
    battery_indicator.jpg
    I suspect that your headset is already fully charged when you did the initial battery charging of 8 hours. Hence, there is no response on the Power LED when you charge the headset for the 2nd time. During the battery charging, the Power LED will blink and stops blinking when it is fully charged.
    Power LED (blinking) - charging
    Power LED (off) - fully charged; power off state
    Power LED (solid white) - fully charged, power on state
    If you like to learn more about charging Tactic3D Rage Wireless, you may refer to this article:
    http://support.creative.com/kb/ShowA...spx?sid=111092
    You may opt for firmware update of the USB wireless transmitter & headset and observe situation can be improved. Please follow the instructions carefully.
    firmware_update.jpg
    Cheers,
    JL-CL

  • Tactic 3d Rage Wireless Possible USB Transmitter Problem

    Hi guys,
    It is my 3rd rage wireless replacement (mini usb charging entrance were broken on the previous two).
    So after unboxing it again, unfortunately I went to firmware page and upgraded the firmwares both usb transmitter and headphones. Nothing went wrong until I try to re pair the headphones with the usb transmitter.
    Headphones are working with every buttons on it, it also gets into pairing mode (with fast blinking red lights). However the usb transmitter does nothing when I hold the connect button, it blinks normal instead of rapidly (as stated in the manual).
    I tried everything and read many threads but could not find similar problem. I do not think that it is bricked but please help me if it is possible to fix this problem.
    Yes it is ridiculous that a simple firmware upgrade is destroying such an expensive product. Shame on you creative!
    Many thanks in advance.

    Originally Posted by Xotli
    Hi guys,
    It is my 3rd rage wireless replacement (mini usb charging entrance were broken on the previous two).
    So after unboxing it again, unfortunately I went to firmware page and upgraded the firmwares both usb transmitter and headphones. Nothing went wrong until I try to re pair the headphones with the usb transmitter.
    Headphones are working with every buttons on it, it also gets into pairing mode (with fast blinking red lights). However the usb transmitter does nothing when I hold the connect button, it blinks normal instead of rapidly (as stated in the manual).
    I tried everything and read many threads but could not find similar problem. I do not think that it is bricked but please help me if it is possible to fix this problem.
    Yes it is ridiculous that a simple firmware upgrade is destroying such an expensive product. Shame on you creative!
    Many thanks in advance.
    Hi Xotli,
    Do you encounter any error(s) during the firmware update of the headset and the USB transmitter?
    Do not connect it to the USB hub. At any one time, the headset and USB transmitter cannot connect together during firmware update; only separate update is allowed.
    Here's the instructions given for updating USB transmitter via Windows:
    - Download the file onto your local hard disk.
    - Ensure that your Sound Blaster Tactic3D Rage Wireless Transmitter is connected to your computer.
    - Ensure that the Sound Blaster Tactic3D Rage Wireless Headset is removed from your computer.
    - Un-compress the downloaded file to a folder in your local hard disk.
    - Double-click <SBTR_PCFW_US_TX_1_59_140721.exe> from the folder which stores the uncompressed files.
    - Follow the instructions on the screen.
    - After the installation of the firmware is completed, unplug and plug in your transmitter and start pairing with the Sound Blaster Tactic3D Rage Wireless headset again.
    Cheers,
    JL-CL

  • Want to buy a Tactic3d Rage Wireless transmitter

    So, I've lost my transmitter for my headset(Yeah, i know). However, the creative support is basically charging me for a new headset when I want to buy a transmitter from them, so I thought I could check if anyone here had an old, used one for sale?

    Originally Posted by Hannestheguy
    So, I've lost my transmitter for my headset(Yeah, i know). However, the creative support is basically charging me for a new headset when I want to buy a transmitter from them, so I thought I could check if anyone here had an old, used one for sale?
    Hi Hannestheguy,
    Hope you get to buy a transmitter for your Rage Wireless headset!
    But in any case it doesnt work out, maybe you can purchase a cheaper set through alternative online sources? (EX: Amazon) I've posted a link below in case youre interested:
    http://www.amazon.com/Creative-Blast.../dp/B008Y1KLME
    Of course this is only a last resort if you dont have the luxury of waiting for a seller.

  • Tactic 3D rage wireless volume change

    I just bought a tactic 3D rage wireless headset, charged it up, installed the control panel and the firmware from the creative website, and it's working well. However every time I adjust the volume on the headset it bleeps, which is very annoying. How do I disable this?

    Hello Zenna,
    Welcome to the forum!
    There is no way to disable the beep sound. When adjusting the volume with the rotary dial, you will get an audible beep tone as an indicator.

  • Creative Sound Blaster Tactic3D Rage Wireless crackling sound

    Tactic3D Rage Wireless crackling sound all the time when playing any sound on the headset.
    Work OK on laptop and other PC in the home. Just not my PC lol. Motherboard: Zotac H55-ITX Wifi. CPU Intel i3.

    Pauleley,
    Welcome to the forum!
    Sounds like an "interference" issue to me. Definitely not an issue with the headset as it is working perfectly fine on another machine. The transmitter operates in the 2.4Ghz frequency spectrum so you might want to check out what other devices runs on the same spectrum near to your computer (just a thought).

  • ThinkPad X300 Wireless security settings

    I just bought this machine and can't get it to load websites.  My provider says that the wireless security settings are probably not allowing the connection.  I get ethernet connection just fine.  It starts to load a site with the wireless but then gets "stuck".  I went through the Lenovo service site and cannot find a telephone number for service!  Can someone tell me the service number or what I should do with these settings?  Thanks

    I posted a request in the ideas section and also sent a support request.  We'll see what happens.

  • Where do I find the wireless network settings (setting up brother MFC)

    Hi
    Sorry if this is a really dumb question but the bloke at Brother said he couldn't help me because I was asking about an Airport Extreme rather than a router....
    By way of quick background I am trying to connect my new Brother MFC-665CW to wirelessly.
    Question 1
    To do this my quick guide tells me I need to:
    1. Write down the wireless network settings of your access point or wireless router.
    SSID
    WEP key (if needed)
    WPA/WPA2-PSK (TKIP or AES) (if needed)
    (I do know I have set up WPA Personal security on my wireless network via my airport extreme and have a 13 letter password.)
    Question 2
    Later in the instructions it asks me to select TKIP or AES - how do I know which one?

    Question 1
    To do this my quick guide tells me I need to:
    1. Write down the wireless network settings of your access point or wireless router.
    SSID
    WEP key (if needed)
    WPA/WPA2-PSK (TKIP or AES) (if needed)
    The SSID would be the same as the AirPort Network Name. Since you set up WPA Personal wireless security on the base station, the type would be WPA-PSK w/TKIP.
    Question 2
    Later in the instructions it asks me to select TKIP or AES - how do I know which one?
    You'll want to choose TKIP. AES is only used with WPA2 Personal.

  • Oficejet 6700 "forget" its wireless connection settings

    Overall the printer works, but after several hours it "forgets" the settings for the wireless router.  I have a dedicated IP of 192.168.1.5 for the MAC address of the printer with the router.  Signal is super strong in this location and the printer detects the wireless network, I just have to set it up every time, go to the router, press the button for 3 seconds, then everything is fine again until several hours later.  I read instructions elsewhere to set the ink level detection to only work while printing and to turn off the scan to computer, but to no avail.
    Does anybody have a similar problem and has a solution?
    This question was solved.
    View Solution.

    O.k., I read elsewhere about another printer that the static IP address needs to be outside of the DHCP range.  My printer's IP was inside that range.  So I made it so that the IP range and the static printer IP don't overlap, and that seems to have done the trick.  Over 24 hours without losing connection.

Maybe you are looking for

  • Returning int array from C to Java as method parameter

    Hello, I've been trying to accomplish this Java int[] myArray = ... (filled with some data); int retCode = myNativeCall(myArray); if(retCode == 0) doSomethingWith(myArray); //myArray gets overwritten with new data (with new size also) during the nati

  • I don't know how to deactivate my iTunes card

    i put my itunes code in at the wrong email

  • Warning due to check scheduling date

    Dear SAP GURU I release production order & check all log. when i chen log for scheduling they give messege "START DATE IN THE PAST TODAY SCEDULING" i made all necessary setting for scheduling in routing, float,customization in scheduling" what is the

  • Problem serving video to Internet explorer

    Hello and thanks in advance to all. I am completely new to Flash Video and FMS, and have encountered a problem when using IE. Following Tom Green's 'Beginners guide to streaming video with Flash Media Server 3.5'  I set up a video to be served from t

  • Mac book pro running hot

    My mac book pro is running very hot. My fans are going like crazy but it doesnt seem to be doing the job. Should i try to clean my fans or something?