3G config problem

HI guys:
i have config the Cisco 881GC-W with PCEX-3G-HSPA card
i have not create the 3G connect to internet
here is debug :
debug ppp chat
debug ppp negotiation
3G_Test#ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
*Aug 19 08:43:01.659: CHAT3: Attempting async line dialer script
*Aug 19 08:43:01.659: CHAT3: Dialing using Modem script: gsm & System script: none
*Aug 19 08:43:01.659: CHAT3: process started
*Aug 19 08:43:01.659: CHAT3: Asserting DTR
*Aug 19 08:43:01.663: CHAT3: Chat script gsm started
*Aug 19 08:43:01.663: CHAT3: Sending string: ATDT#777
*Aug 19 08:43:01.663: CHAT3: Chat script gsm finished, status = Success.
*Aug 19 08:43:04.731: %LINK-3-UPDOWN: Interface Cellular0, changed state to up.
Success rate is 0 percent (0/5)
3G_Test#
*Aug 19 08:43:04.731: Ce0 PPP: Using dialer call direction
*Aug 19 08:43:04.731: Ce0 PPP: Treating connection as a callout
*Aug 19 08:43:04.731: Ce0 PPP: Session handle[27000040] Session id[22]
*Aug 19 08:43:04.731: Ce0 PPP: Phase is ESTABLISHING, Active Open
*Aug 19 08:43:04.731: Ce0 PPP: Authorization required
*Aug 19 08:43:04.731: Ce0 PPP: No remote authentication for call-out
*Aug 19 08:43:04.731: Ce0 LCP: O CONFREQ [Closed] id 211 len 20
*Aug 19 08:43:04.731: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:04.731: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:04.731: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:04.731: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:06.715: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:06.715: Ce0 LCP: O CONFREQ [REQsent] id 212 len 20
*Aug 19 08:43:06.715: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:06.715: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:06.715: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:06.715: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:08.731: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:08.731: Ce0 LCP: O CONFREQ [REQsent] id 213 len 20
*Aug 19 08:43:08.731: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:08.731: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:08.731: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:08.731: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:10.747: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:10.747: Ce0 LCP: O CONFREQ [REQsent] id 214 len 20
*Aug 19 08:43:10.747: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:10.747: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:10.747: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:10.747: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:12.763: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:12.763: Ce0 LCP: O CONFREQ [REQsent] id 215 len 20
*Aug 19 08:43:12.763: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:12.763: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:12.763: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:12.763: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:14.779: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:14.779: Ce0 LCP: O CONFREQ [REQsent] id 216 len 20
*Aug 19 08:43:14.779: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:14.779: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:14.779: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:14.779: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:16.795: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:16.795: Ce0 LCP: O CONFREQ [REQsent] id 217 len 20
*Aug 19 08:43:16.795: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:16.795: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:16.795: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:16.795: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:18.811: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:18.811: Ce0 LCP: O CONFREQ [REQsent] id 218 len 20
*Aug 19 08:43:18.811: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:18.811: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:18.811: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:18.811: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:20.827: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:20.827: Ce0 LCP: O CONFREQ [REQsent] id 219 len 20
*Aug 19 08:43:20.827: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:20.827: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:20.827: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:20.827: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:22.843: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:22.843: Ce0 LCP: O CONFREQ [REQsent] id 220 len 20
*Aug 19 08:43:22.843: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Aug 19 08:43:22.843: Ce0 LCP:    MagicNumber 0x2710E450 (0x05062710E450)
*Aug 19 08:43:22.843: Ce0 LCP:    PFC (0x0702)
*Aug 19 08:43:22.843: Ce0 LCP:    ACFC (0x0802)
*Aug 19 08:43:24.859: Ce0 LCP: Timeout: State REQsent
*Aug 19 08:43:24.859: Ce0 PPP: Sending Acct Event[Down] id[1A]
*Aug 19 08:43:24.859: Ce0 LCP: State is Closed
*Aug 19 08:43:24.859: Ce0 PPP: Phase is DOWN
*Aug 19 08:43:24.859: Ce0 LCP: State is Listen
*Aug 19 08:43:26.859: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
*Aug 19 08:43:26.859: Ce0 LCP: State is Closed
*Aug 19 08:43:31.931: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
3G_Test#
3G_Test#
it may be a ppp link problem,because Chat script gsm finished, status = Success,but i dont't understand why cell 0 didn't UP
here is my config:
chat-script gsm "" "ATDT#777"
interface Cellular0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer in-band
dialer string gsm
dialer-group 1
async mode interactive
ppp chap hostname card
ppp chap password 0 card
ppp ipcp dns request
interface Vlan1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Cellular0
ip http server
ip http secure-server
ip nat inside source list 1 interface Cellular0 overload
access-list 1 permit any
dialer-list 1 protocol ip list 1
control-plane
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line 3
script dialer gsm
no exec
line vty 0 4
login
anyone can help me ?thanks!

Hi,
I have not an solution but rather a similar problem with that kind of hardware (881GW with PCEX-3G-HSPA). I have a working config for only *one* successful 3G dial-in: after losing the established 3G connection (e.g. forcing a "clear int dial 1"), the router can not re-establish the 3G connection until I reboot the device. It seems that the communication between IOS and the modem is some kind of damaged:
Config:
=====
chat-script GSM "" AT OK "ATDT*99*1#"
interface Cellular0
no ip address
ip virtual-reassembly in
encapsulation ppp
dialer in-band
dialer pool-member 1
async mode interactive
no ppp lcp fast-start
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
dialer idle-timeout 0
dialer string GSM
dialer-group 1
no ppp lcp fast-start
ppp chap refuse
ppp pap sent-username USER password TEST
ip route 0.0.0.0 0.0.0.0 Dialer1
dialer-list 1 protocol ip permit
line 3
exec-timeout 0 0
script dialer GSM
modem InOut
no exec
1st login - successful:
================
*Nov 10 16:28:40.955: Ce0 DDR: rotor dialout [best] least recent failure is also most recent failure
*Nov 10 16:28:40.955: Ce0 DDR: rotor dialout [best] trying untried dialout
*Nov 10 16:28:40.955: Ce0 DDR: rotor dialout [best] also has most recent failure
*Nov 10 16:28:40.955: Ce0 DDR: rotor dialout [best]
*Nov 10 16:28:40.955: Ce0 DDR: Dialing cause ip (s=10.98.3.10, d=17.72.255.12)
*Nov 10 16:28:40.955: Ce0 DDR: Attempting to dial GSM
*Nov 10 16:28:40.955: CHAT3: Attempting async line dialer script
*Nov 10 16:28:40.955: CHAT3: Dialing using Modem script: GSM & System script: none
*Nov 10 16:28:40.955: CHAT3: process started
*Nov 10 16:28:40.955: CHAT3: Asserting DTR
*Nov 10 16:28:40.959: CHAT3: Chat script GSM started
*Nov 10 16:28:40.959: CHAT3: Sending string: AT
*Nov 10 16:28:40.959: CHAT3: Expecting string: OK
*Nov 10 16:28:40.963: CHAT3: Completed match for expect: OK
*Nov 10 16:28:40.963: CHAT3: Sending string: ATDT*99*1#
*Nov 10 16:28:40.963: CHAT3: Chat script GSM finished, status = Success
*Nov 10 16:28:42.039: TTY3: no timer type 1 to destroy
*Nov 10 16:28:42.039: TTY3: no timer type 0 to destroy
*Nov 10 16:28:42.039: TTY3: no timer type 2 to destroy
*Nov 10 16:28:44.039: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
*Nov 10 16:28:44.039: Ce0 DDR: Dialer statechange to up
*Nov 10 16:28:44.039: %DIALER-6-BIND: Interface Ce0 bound to profile Di1
*Nov 10 16:28:44.039: Ce0 DDR: Dialer call has been placed
*Nov 10 16:28:44.039: Ce0 PPP: Sending cstate UP notification
*Nov 10 16:28:44.039: Ce0 PPP: Processing CstateUp message
*Nov 10 16:28:44.067: PPP: Alloc Context [84DAA350]
*Nov 10 16:28:44.067: ppp1 PPP: Phase is ESTABLISHING
*Nov 10 16:28:44.067: ppp1 PPP: Using AAA Unique Id = D
*Nov 10 16:28:44.067: Ce0 PPP: Authorization required
*Nov 10 16:28:44.067: Ce0 PPP: Using dialer call direction
*Nov 10 16:28:44.067: Ce0 PPP: Treating connection as a callout
*Nov 10 16:28:44.067: Ce0 PPP: Session handle[FE000001] Session id[1]
*Nov 10 16:28:44.067: Ce0 LCP: Event[OPEN] State[Initial to Starting]
*Nov 10 16:28:44.071: Ce0 PPP: No remote authentication for call-out
*Nov 10 16:28:44.071: Ce0 LCP: O CONFREQ [Starting] id 1 len 20
*Nov 10 16:28:44.071: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Nov 10 16:28:44.071: Ce0 LCP:    MagicNumber 0x4C781BD5 (0x05064C781BD5)
*Nov 10 16:28:44.071: Ce0 LCP:    PFC (0x0702)
*Nov 10 16:28:44.071: Ce0 LCP:    ACFC (0x0802)
*Nov 10 16:28:44.071: Ce0 LCP: Event[UP] State[Starting to REQsent]
*Nov 10 16:28:44.079: Ce0 LCP: I CONFACK [REQsent] id 1 len 20
*Nov 10 16:28:44.079: Ce0 LCP:    ACCM 0x000A0000 (0x0206000A0000)
*Nov 10 16:28:44.079: Ce0 LCP:    MagicNumber 0x4C781BD5 (0x05064C781BD5)
*Nov 10 16:28:44.079: Ce0 LCP:    PFC (0x0702)
*Nov 10 16:28:44.079: Ce0 LCP:    ACFC (0x0802)
*Nov 10 16:28:47.971: Ce0 IPCP: O CONFREQ [ACKsent] id 4 len 10
*Nov 10 16:28:47.971: Ce0 IPCP:    Address 10.99.17.58 (0x03060A63113A)
*Nov 10 16:28:47.971: Ce0 IPCP: Event[Receive ConfNak/Rej] State[ACKsent to ACKsent]
*Nov 10 16:28:48.027: Ce0 IPCP: I CONFACK [ACKsent] id 4 len 10
*Nov 10 16:28:48.027: Ce0 IPCP:    Address 10.99.17.58 (0x03060A63113A)
*Nov 10 16:28:48.027: Ce0 IPCP: Event[Receive ConfAck] State[ACKsent to Open]
*Nov 10 16:28:48.027: Ce0 IPCP: State is Open
*Nov 10 16:28:48.027: Di1 IPCP: Install negotiated IP interface address 10.99.17.58
*Nov 10 16:28:48.031: Ce0 DDR: dialer protocol up1#
--> Now I do a "clear int dial 1":
2nd and all further logins - failure:
========================
*Nov 10 17:37:53.467: Ce0 DDR: rotor dialout [best] least recent failure is also most recent failure
*Nov 10 17:37:53.467: Ce0 DDR: rotor dialout [best] also has most recent failure
*Nov 10 17:37:53.467: Ce0 DDR: rotor dialout [best]
*Nov 10 17:37:53.467: Ce0 DDR: Dialing cause ip (s=10.98.3.10, d=10.99.16.254)
*Nov 10 17:37:53.467: Ce0 DDR: Attempting to dial GSM
*Nov 10 17:37:53.467: CHAT3: Attempting async line dialer script
*Nov 10 17:37:53.467: CHAT3: Dialing using Modem script: GSM & System script: none
*Nov 10 17:37:53.471: CHAT3: process started
*Nov 10 17:37:53.471: CHAT3: Asserting DTR
*Nov 10 17:37:53.471: CHAT3: Chat script GSM started
*Nov 10 17:37:53.475: CHAT3: Sending string: AT
*Nov 10 17:37:53.475: CHAT3: Expecting string: OK
*Nov 10 17:37:58.475: CHAT3: Timeout expecting: OK
*Nov 10 17:37:58.475: CHAT3: Chat script GSM finished, status = Connection timed out; remote host not responding
*Nov 10 17:37:58.475: TTY3: Line reset by "Async dialer"
*Nov 10 17:37:58.475: Ce0 DDR: disconnecting call
*Nov 10 17:37:58.475: TTY3: dropping DTR
*Nov 10 17:37:59.475: TTY3: asserting DTR
*Nov 10 17:37:59.475: TTY3: Modem: (unknown)->READY
Maybe somone has some clue how this can happen?
Gerald

Similar Messages

  • Audio Config" problem after upgrading to 7.6

    I have only had my ipod one week. It is working beautifully. My problem is that I can no longer charge it or add songs to it because I can not open itunes. The previous version worked beautifully on my computer. After I upgraded to 7.6, it stopped working and I get an Audio Config. problem everytime I try to open it. I have tried uninstalling and reinstalling the program but it does not help. What do I need to do to fix this problem?

    I have had my ipod a few weeks - but have nothing but problems letting itunes run the syncing, sometime it works and sometimes it does not. I had to reset my ipod 2 times already just to keep song on here, should have gone with Zune or Sonys (what my wife has) they are not having a single issue...
    I would like to add my voice to his - I upgraded to 7.6, it stopped working and I get an Audio Config. problem everytime I try to open it. I have tried uninstalling and reinstalling the program but it does not help. What do I need to do to fix this problem ! ! ! ! ?

  • [SOLVED]Xorg.conf, mouse config problem

    The Rapoo M765 mouse can not work properly under normal mouse configuration.
    The mouse goes beyond controll when config as below:
    hacksign@XSign [14:13:13] : ~
    >> cat /etc/X11/xorg.conf.d/50-mouse-acceleration.conf
    #Section "InputClass"
    # Identifier "Mouse2"
    # MatchProduct "RAPOO RAPOO 2.4G Remote Mouse"
    # MatchIsPointer "yes"
    # MatchDevicePath "/dev/input/event*"
    # Driver "mouse"
    # Option "Protocol" "auto"
    # Option "Emulate3Buttons" "no"
    # Option "Buttons" "7"
    # Option "ButtonMapping" "1 2 3 6 7"
    #EndSection
    When there is no any configuration, the mouse can work abnormally. Movement and right/left click work fine, but I can not use scroll wheel,and the "go forward"&"go backward" mouse key can not work too.
    (I know Option "ZAxisMapping" "4 5" is the configuration of scroll wheel emulation.)
    The real problem is 'mouse beyond controll',the cursor goes crazyly on screen ....
    I guess it is something wrong of ButtonMapping option. But when I tried to get button number from command xev,when scroll wheel scrolles, I get something below(the scroll wheel movement is identified as a key event~):
    //left click
    ButtonPress event, serial 34, synthetic NO, window 0x4a00001,
    root 0x264, subw 0x0, time 3766452, (135,143), root:(2287,595),
    state 0x0, button 1, same_screen YES
    ButtonRelease event, serial 34, synthetic NO, window 0x4a00001,
    root 0x264, subw 0x0, time 3766588, (135,143), root:(2287,595),
    state 0x100, button 1, same_screen YES
    //right click
    ButtonPress event, serial 34, synthetic NO, window 0x4a00001,
    root 0x264, subw 0x0, time 3767716, (135,143), root:(2287,595),
    state 0x0, button 3, same_screen YES
    ButtonRelease event, serial 34, synthetic NO, window 0x4a00001,
    root 0x264, subw 0x0, time 3767852, (135,143), root:(2287,595),
    state 0x400, button 3, same_screen YES
    //mouse scroll, identified as keyboard event(?)
    KeyRelease event, serial 34, synthetic NO, window 0x4a00001,
    root 0x264, subw 0x0, time 3769332, (135,143), root:(2287,595),
    state 0x0, keycode 123 (keysym 0x1008ff13, XF86AudioRaiseVolume), same_screen YES,
    XLookupString gives 0 bytes:
    XFilterEvent returns: False
    KeyPress event, serial 34, synthetic NO, window 0x4a00001,
    root 0x264, subw 0x0, time 3769332, (135,143), root:(2287,595),
    state 0x0, keycode 122 (keysym 0x1008ff11, XF86AudioLowerVolume), same_screen YES,
    XLookupString gives 0 bytes:
    XmbLookupString gives 0 bytes:
    XFilterEvent returns: False
    here is some Information(I dont know why the mouse is identified as 'type:KEYBOARD'):
    hacksign@XSign [14:55:03] : ~
    >> xinput
    ⎡ Virtual core pointer id=2 [master pointer (3)]
    ⎜ ↳ Virtual core XTEST pointer id=4 [slave pointer (2)]
    ⎜ ↳ RAPOO RAPOO 2.4G Remote Mouse id=13 [slave pointer (2)]
    ⎜ ↳ SynPS/2 Synaptics TouchPad id=15 [slave pointer (2)]
    ⎜ ↳ TPPS/2 IBM TrackPoint id=16 [slave pointer (2)]
    ⎣ Virtual core keyboard id=3 [master keyboard (2)]
    ↳ Virtual core XTEST keyboard id=5 [slave keyboard (3)]
    ↳ Power Button id=6 [slave keyboard (3)]
    ↳ Video Bus id=7 [slave keyboard (3)]
    ↳ Sleep Button id=8 [slave keyboard (3)]
    ↳ Heng Yu Technology Poker Pro S id=9 [slave keyboard (3)]
    ↳ Heng Yu Technology Poker Pro S id=10 [slave keyboard (3)]
    ↳ Integrated Camera id=11 [slave keyboard (3)]
    ↳ RAPOO RAPOO 2.4G Remote Mouse id=12 [slave keyboard (3)]
    ↳ AT Translated Set 2 keyboard id=14 [slave keyboard (3)]
    ↳ ThinkPad Extra Buttons id=17 [slave keyboard (3)]
    hacksign@XSign [14:55:06] : ~
    >> xinput list-props 13
    Device 'RAPOO RAPOO 2.4G Remote Mouse':
    Device Enabled (142): 1
    Coordinate Transformation Matrix (144): 1.000000, 0.000000, 0.000000, 0.000000, 1.000000, 0.000000, 0.000000, 0.000000, 1.000000
    Device Accel Profile (270): 0
    Device Accel Constant Deceleration (271): 1.000000
    Device Accel Adaptive Deceleration (272): 1.000000
    Device Accel Velocity Scaling (273): 10.000000
    Device Product ID (260): 9390, 8192
    Device Node (261): "/dev/input/event8"
    Evdev Axis Inversion (274): 0, 0
    Evdev Axes Swap (276): 0
    Axis Labels (277): "Rel X" (152), "Rel Y" (153), "Rel Horiz Wheel" (267), "Rel Dial" (268), "Rel Vert Wheel" (269)
    Button Labels (278): "Button Left" (145), "Button Middle" (146), "Button Right" (147), "Button Wheel Up" (148), "Button Wheel Down" (149), "Button Horiz Wheel Left" (150), "Button Horiz Wheel Right" (151), "Button Side" (265), "Button Extra" (266), "Button Unknown" (263), "Button Unknown" (263), "Button Unknown" (263), "Button Unknown" (263)
    Evdev Scrolling Distance (279): 1, 1, 1
    Evdev Middle Button Emulation (280): 0
    Evdev Middle Button Timeout (281): 50
    Evdev Third Button Emulation (282): 0
    Evdev Third Button Emulation Timeout (283): 1000
    Evdev Third Button Emulation Button (284): 3
    Evdev Third Button Emulation Threshold (285): 20
    Evdev Wheel Emulation (286): 0
    Evdev Wheel Emulation Axes (287): 0, 0, 4, 5
    Evdev Wheel Emulation Inertia (288): 10
    Evdev Wheel Emulation Timeout (289): 200
    Evdev Wheel Emulation Button (290): 4
    Evdev Drag Lock Buttons (291): 0
    hacksign@XSign [14:55:14] : ~
    >> grep -i rapoo /var/log/Xorg.0.log
    [ 29.102] (II) config/udev: Adding input device RAPOO RAPOO 2.4G Remote Mouse (/dev/input/event7)
    [ 29.102] (**) RAPOO RAPOO 2.4G Remote Mouse: Applying InputClass "evdev keyboard catchall"
    [ 29.102] (II) Using input driver 'evdev' for 'RAPOO RAPOO 2.4G Remote Mouse'
    [ 29.102] (**) RAPOO RAPOO 2.4G Remote Mouse: always reports core events
    [ 29.102] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: Device: "/dev/input/event7"
    [ 29.102] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Vendor 0x24ae Product 0x2000
    [ 29.102] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found keys
    [ 29.102] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Configuring as keyboard
    [ 29.102] (II) XINPUT: Adding extended input device "RAPOO RAPOO 2.4G Remote Mouse" (type: KEYBOARD, id 12)
    [ 29.103] (II) config/udev: Adding input device RAPOO RAPOO 2.4G Remote Mouse (/dev/input/event8)
    [ 29.103] (**) RAPOO RAPOO 2.4G Remote Mouse: Applying InputClass "evdev pointer catchall"
    [ 29.103] (**) RAPOO RAPOO 2.4G Remote Mouse: Applying InputClass "evdev keyboard catchall"
    [ 29.103] (II) Using input driver 'evdev' for 'RAPOO RAPOO 2.4G Remote Mouse'
    [ 29.103] (**) RAPOO RAPOO 2.4G Remote Mouse: always reports core events
    [ 29.103] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: Device: "/dev/input/event8"
    [ 29.103] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Vendor 0x24ae Product 0x2000
    [ 29.103] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found 9 mouse buttons
    [ 29.103] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found scroll wheel(s)
    [ 29.103] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found relative axes
    [ 29.103] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found x and y relative axes
    [ 29.103] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found absolute axes
    [ 29.103] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Forcing absolute x/y axes to exist.
    [ 29.103] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found keys
    [ 29.103] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Configuring as mouse
    [ 29.103] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Configuring as keyboard
    [ 29.103] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Adding scrollwheel support
    [ 29.103] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: YAxisMapping: buttons 4 and 5
    [ 29.103] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 29.103] (II) XINPUT: Adding extended input device "RAPOO RAPOO 2.4G Remote Mouse" (type: KEYBOARD, id 13)
    [ 29.104] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: initialized for relative axes.
    [ 29.104] (WW) evdev: RAPOO RAPOO 2.4G Remote Mouse: ignoring absolute axes.
    [ 29.104] (**) RAPOO RAPOO 2.4G Remote Mouse: (accel) keeping acceleration scheme 1
    [ 29.104] (**) RAPOO RAPOO 2.4G Remote Mouse: (accel) acceleration profile 0
    [ 29.104] (**) RAPOO RAPOO 2.4G Remote Mouse: (accel) acceleration factor: 2.000
    [ 29.104] (**) RAPOO RAPOO 2.4G Remote Mouse: (accel) acceleration threshold: 4
    [ 29.104] (II) config/udev: Adding input device RAPOO RAPOO 2.4G Remote Mouse (/dev/input/mouse0)
    hacksign@XSign [14:59:47] : ~
    >> yaourt -Q|grep -i 'input-'
    local/xf86-input-evdev-trackpoint 2.9.1-1
    extra/xf86-input-keyboard 1.8.0-3 (xorg-drivers xorg)
    extra/xf86-input-mouse 1.9.1-1 (xorg-drivers xorg)
    extra/xf86-input-synaptics 1.8.1-1 (xorg-drivers xorg)
    Last edited by Hacksign (2015-01-14 02:22:51)

    Thanks for reply !
    change Driver 'mouse' to Driver 'evdev',solved cursor goes beyond controll problem.
    but I still can not use scroll button and 'go forward'&'go backward' button.
    (BTW:evdev_drv.so is from local/xf86-input-evdev-trackpoint, and local/xf86-input-evdev-trackpoint package is from AUR)
    I think, maybe something wrong with my button number mapping, but I still can not get scroll button number with 'xev' command....
    below is my configuration:
    hacksign@XSign [17:15:19] : /var/log
    >> cat /etc/X11/xorg.conf.d/50-mouse-acceleration.conf
    Section "InputClass"
    Identifier "Mouse2"
    MatchProduct "RAPOO RAPOO 2.4G Remote Mouse"
    MatchIsPointer "yes"
    MatchDevicePath "/dev/input/event*"
    Driver "evdev"
    Option "Protocol" "auto"
    Option "Emulate3Buttons" "no"
    Option "ZAxisMapping" "4 5"
    Option "Buttons" "9"
    Option "ButtonMapping" "1 2 3 6 7 8 9 4 5"
    EndSection
    and here is Xorg.0.log
    [ 11357.287] (**) RAPOO RAPOO 2.4G Remote Mouse: Applying InputClass "evdev keyboard catchall"
    [ 11357.287] (II) Using input driver 'evdev' for 'RAPOO RAPOO 2.4G Remote Mouse'
    [ 11357.287] (**) RAPOO RAPOO 2.4G Remote Mouse: always reports core events
    [ 11357.287] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: Device: "/dev/input/event7"
    [ 11357.287] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Vendor 0x24ae Product 0x2000
    [ 11357.287] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found keys
    [ 11357.287] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Configuring as keyboard
    [ 11357.287] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/0003:24AE:2000.0003/input/input8/event7"
    [ 11357.288] (II) XINPUT: Adding extended input device "RAPOO RAPOO 2.4G Remote Mouse" (type: KEYBOARD, id 12)
    [ 11357.288] (**) Option "xkb_rules" "evdev"
    [ 11357.288] (**) Option "xkb_model" "pc104"
    [ 11357.288] (**) Option "xkb_layout" "us"
    [ 11357.288] (II) config/udev: Adding input device RAPOO RAPOO 2.4G Remote Mouse (/dev/input/event8)
    [ 11357.288] (**) RAPOO RAPOO 2.4G Remote Mouse: Applying InputClass "evdev pointer catchall"
    [ 11357.288] (**) RAPOO RAPOO 2.4G Remote Mouse: Applying InputClass "evdev keyboard catchall"
    [ 11357.288] (**) RAPOO RAPOO 2.4G Remote Mouse: Applying InputClass "Mouse2"
    [ 11357.288] (II) Using input driver 'evdev' for 'RAPOO RAPOO 2.4G Remote Mouse'
    [ 11357.288] (**) RAPOO RAPOO 2.4G Remote Mouse: always reports core events
    [ 11357.288] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: Device: "/dev/input/event8"
    [ 11357.288] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: ButtonMapping '1 2 3 6 7 8 9 4 5'
    [ 11357.288] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Vendor 0x24ae Product 0x2000
    [ 11357.288] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found 9 mouse buttons
    [ 11357.288] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found scroll wheel(s)
    [ 11357.288] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found relative axes
    [ 11357.288] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found x and y relative axes
    [ 11357.288] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found absolute axes
    [ 11357.288] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Forcing absolute x/y axes to exist.
    [ 11357.288] (--) evdev: RAPOO RAPOO 2.4G Remote Mouse: Found keys
    [ 11357.288] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Configuring as mouse
    [ 11357.288] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Configuring as keyboard
    [ 11357.288] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: Adding scrollwheel support
    [ 11357.288] (**) Option "Emulate3Buttons" "no"
    [ 11357.288] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: YAxisMapping: buttons 4 and 5
    [ 11357.288] (**) evdev: RAPOO RAPOO 2.4G Remote Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 11357.288] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.1/0003:24AE:2000.0004/input/input9/event8"
    [ 11357.288] (II) XINPUT: Adding extended input device "RAPOO RAPOO 2.4G Remote Mouse" (type: KEYBOARD, id 13)
    [ 11357.288] (**) Option "xkb_rules" "evdev"
    [ 11357.288] (**) Option "xkb_model" "pc104"
    [ 11357.288] (**) Option "xkb_layout" "us"
    [ 11357.288] (II) evdev: RAPOO RAPOO 2.4G Remote Mouse: initialized for relative axes.
    [ 11357.288] (WW) evdev: RAPOO RAPOO 2.4G Remote Mouse: ignoring absolute axes.
    [ 11357.289] (**) RAPOO RAPOO 2.4G Remote Mouse: (accel) keeping acceleration scheme 1
    [ 11357.289] (**) RAPOO RAPOO 2.4G Remote Mouse: (accel) acceleration profile 0
    [ 11357.289] (**) RAPOO RAPOO 2.4G Remote Mouse: (accel) acceleration factor: 2.000
    [ 11357.289] (**) RAPOO RAPOO 2.4G Remote Mouse: (accel) acceleration threshold: 4
    [ 11357.289] (II) config/udev: Adding input device RAPOO RAPOO 2.4G Remote Mouse (/dev/input/mouse0)
    [ 11357.289] (II) No input driver specified, ignoring this device.
    [ 11357.289] (II) This device may have been added with another device file.
    olive wrote:In the config file you mentioned, all is commented; do you mean that you have problems when you have uncommented it? You should not use the mouse driver (old deprecated driver) but evdev. Try to remove xf86-input-mouse and xf86-input-keyboard (same as before, this is deprecated and handled by evdev) and remove also a "joystick" driver if you have it (I have had problem with it conflicting with the evdev driver).
    Last edited by Hacksign (2015-01-13 09:27:06)

  • FTP Adapter config problem (again :/ )

    Hello all.
    I know that this topic was discussed few times before but i still cant setup my FTP adapter.
    My OS is Win XP. I downloaded free ftp server (XLight FTP Server) and setup my oc4j-ra.xml in following way:
         <connector-factory location="eis/Ftp/FtpAdapter" connector-name="Ftp Adapter">
         <config-property name="host" value="10.172.201.57"/>
         <config-property name="port" value="210"/>
         <config-property name="username" value="szeryf"/>
         <config-property name="password" value="szeryf"/>
         </connector-factory>
    where shown ip address is my computer address. I also created user szeryf/szeryf at my local FTP server and tried to connect to that server using some ftp client - with success. Then i created some simple BPEL process to upload file to FTP server. Each time i try i get fault that connection to server failed.
    Maybe someone experienced such a thing and could help me with that problem?
    Regards,
    Chris

    Are you sure your ftp server is on port 210? It seems odd.
    And is there a reason you are editing oc4j-ra.xml directly? Why not make a partner link and get that working first?

  • Visa config. problem

    Hi, everyone
    I connect my device at COM1, but I cannot find that com port in serial config.
    It means I cannot find any connection with my device in system manager.
    I only want to use labview to control my device, even not use dll.
    Anybody can figure out what problems in my situation ?
    # I use vb.net to do the same thing, and it works. So I think my deivce have no problems.
    Certified LabVIEW Developer

    Hi, RavensFan
    Com1 shows in windows device manager, but it not show my device name.
    Like this picture.
    So visa resource name not show "Com1".
    I didn't install MAX, and I will try later and reinstall my visa driver.
    thank for your reply.
    Certified LabVIEW Developer

  • Config problem when transport

    Hi Experts,
    I created a Z output type in NACE in Dev system 200 client. and with this i create a process code to for my inbound IDOC partner profile. Along with this we created IDOC segments and other stuff. Now after transport I am not getting these changes reflected in TST System
    How can we confirm about thr TR request number in whic TR the changes saved.
    I think the possible problems are:
    1. May be saved in any other TR or
    2. Because of config changes are done in 200 client instead of 100 client.
    I have no idea about config related things.
    Can anyone please tell me about the problem and its solution
    Regards,
    Nik

    Hi John,
    Thanks for your reply. The thing is,
    I dont remember, when i created the Process code for inbound IDOC did it asked for the TR, ya it must ask, but i forget the TR number. Can you please help me how to get which TR it is saved. Also the thing is when i treed creating new Process Code it is not asking me any TR. So the Posibilities i think may be it dont ask for the TR or a TR is not Transported thats y it is not asking me for the new TR.
    In menu i am not getting any button which tell me about the TR in which the process code saved.
    For NACE issue, i am bit confused regarding the client. Can u please explain me to add an output type in NACE, which client i have to use (100 client ?).For a new output type I used the cleint i usually work on i.e 200. and things are working fine in DEV, But when i transported all my requests to TST server, i am not able to see the output type there in TST system.
    DO I NEED TO DO BOTH THINGS PROCESS CODE & NACE IN CONFIG CLIENT ??
    Regards,
    Nik

  • LMS 4.1 multiserver config problem

    I m facing a problem in multiserver configuration, in making master-slave servers.
    Master server config is done, certificates are imported, SSO is also configured and all the pre-requisites given in the multiserver-config doc of lms4.1.
    While making slave server from stand-alone, getting errors like "cetrificate expired" and "certificte not installed" in two different ways, putting master-server IP as master address and putting master-server domain name respectively, both snapshots are attached. My Domain name is DNS resolvable.
    Anyone can help me out on this...?

    You can add your custom prompts into /opt/CSCOpx/objects/cmf/data/TacacsPrompts.ini. No restart of LMS is required for the addition to be recognized.

  • Oracle net8 easy config Problem

    i am not able configure Oracle net8 easy config in oracle forms & Reports.When i click the Oracle net8 easy config shortcut,then the window is not shown .After that there is no action .i am using P4 1.7GHz with 128DDR RAM.
    How can i retrive this problem.
    Thanks
    Cyril

    You can modify script file "..\orant\NET80\ADMIN\tnsnames.ora"
    LOCAL.WORLD =
    (DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = DB Server name)(PORT = 1521))
    (CONNECT_DATA = (SID = ORCL))
    HAFEEZ

  • IGS Config Problem: ListenerRfc::Abort - Help Please!

    Hello,
    I've been working with getting IGS installed and working and can't figure out what's wrong. the install came back successful. I've gone through and fixed, and tested, my SM59 definitions. Gone through OSS and looked at the recommended notes, etc. (all the usual stuff). Now I'm getting desperate!)
    Here's the message our app gets via the www query trying to get graphs:
    "IGS: Error When Calling Up IGS (ListenerRfc: unknown error)"
    Here's what I've done to date:
    1. re-installed it (on my BW C/I - same host - which is an ABAP instance ONLY)
    2. corrected the default SM59 defintions (set them to what's spec'd in the igs.xml file) and tested them out.
    3. manually started and stopped it
    4. In troubleshooting the MUX - here's what I get from the log mux_"sap-bid1.trc"
    [Thr 3342] Sat Dec 24 10:49:08 2005
    [Thr 3342] [ListenerRfc::Abort] Aborted
    [Thr 3342] [ListenerRfc::Cleanup] Cleaned up
    [Thr 258] [ListenerRfc::DispatchRfc] returned with Abort()
    Which tells me my ListenerRfc isn't "hearing" the request for graphics yes?
    So how to I configure it - ListenerRfc - if that is indeed the problem?

    Resolved - AFTER IGS patch 10 application, IGS was looking for gfwchart (versus gfwchart.tpl - see below)
    Fixed it by renaming the file...
    sap-bid1:bidadm 10> more chart_11054d91098584_5.trc
    Can't find config file  /usr/sap/BID/DVEBMGS00/igs/conf/gfwchart
    sap-bid1:bidadm 11> cd /usr/sap/BID/DVEBMGS00/igs/conf/
    sap-bid1:bidadm 12> ls
    dev_sapstart  gfwchart.tpl  igs.xml       xmlchart.tpl

  • Struts-Config Problem

    An error message told me to post to the forum (I do what I'm told). Mmmmkay - background on what probably caused it - I manually added multiple instances of the same action (with slightly different attributes) and had the forward loop back to the instantiating(?) uix. Figured even if I pulled this off it would be a bad way to do what I was trying to do. I deleted all but one instance of that action in the struts-config, so the xml is again in a valid state. The struts-config diagram still had forwards looping back to the data page so I tried to delete them and I get the error below. n e ways here it goes JDev developers:
    BME-99003: An error occurred, so processing could not continue.
    The application has tried to de-reference an invalid pointer. This exception should have been dealt with programatically. The current activity may fail and the system may have been left in an unstable state. The following is a stack trace.
    java.lang.NullPointerException
         at oracle.bm.diagrammer.track.MoveTracker.addEdgesToImpliedList(MoveTracker.java:372)
         at oracle.bm.diagrammer.track.MoveTracker.<init>(MoveTracker.java:198)
         at oracle.bm.diagrammer.track.SelectionTracker.mousePressed(SelectionTracker.java:788)
         at oracle.bm.diagrammer.track.ModularTracker.processEvent(ModularTracker.java:215)
         at oracle.bm.diagrammer.track.SelectionTracker.processEvent(SelectionTracker.java:163)
         at oracle.bm.diagrammer.track.TrackerStack.processEvent(TrackerStack.java:349)
         at oracle.bm.diagrammer.BaseDiagramView$2.processEvent(BaseDiagramView.java:689)
         at oracle.bm.diagrammer.PageView$PageViewPanel.fireEvent(PageView.java:2569)
         at oracle.bm.diagrammer.PageView$PageViewPanel.processEvent(PageView.java:2734)
         at java.awt.Component.dispatchEventImpl(Component.java:3615)
         at java.awt.Container.dispatchEventImpl(Container.java:1627)
         at java.awt.Component.dispatchEvent(Component.java:3477)
         at java.awt.LightweightDispatcher.retargetMouseEvent(Container.java:3483)
         at java.awt.LightweightDispatcher.processMouseEvent(Container.java:3195)
         at java.awt.LightweightDispatcher.dispatchEvent(Container.java:3128)
         at java.awt.Container.dispatchEventImpl(Container.java:1613)
         at java.awt.Window.dispatchEventImpl(Window.java:1606)
         at java.awt.Component.dispatchEvent(Component.java:3477)
         at java.awt.EventQueue.dispatchEvent(EventQueue.java:456)
         at java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.java:201)
         at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:151)
         at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:145)
         at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:137)
         at java.awt.EventDispatchThread.run(EventDispatchThread.java:100)
    If further errors occur, you should restart the application.
    Yes I keep getting this error after restart of JDev
    Also, report the problem on the JDeveloper forum on otn.oracle.com, or contact Oracle support, giving the information from this message.

    Brian - I think the simplest way to recover from this will be to go to the ViewController/model directory and delete (or rename) the StrutsPageflow.oxd_struts file.
    This will blow away the diagram and a new one will be created when you next open the struts-config.
    You'll loose the diagram layout but the metadata will all be intact

  • DSD config problem

    hi experts.
    I want to implement MDSD but facing quite a number of problems.
    1. When I try to configure DSD Backend and DSD connector I get confuse whether config guide speaks for WAS or Backend Config.Can someone guide me what configurations are needed to be done on which system.
    2. Secondly when i try to import MDSD.jar it gives an error--Jar file is not valid MI AWT application!
    Reason: Error in created project in:finishOpenArchivePage.
    Thanks in advance
    Akhil

    hi Akhil,
    please go thru this pdf u can get ur solution
    https://websmp208.sap-ag.de/~sapidp/011000358700001052502007D
    if helpfull please reward me points.
    thanks
    karthikeya

  • [solved] Need DEFINITE solution to 'no more qt-config' problem

    The qt-config utility (the one with which you could "switch" between qt3 and qt4) recently vanished. Is there a known definite solution to this problem, i.e. a way to set EXACTLY the same states/variables/symlinks/whatever that were set with "qt-config qt" and "qt-config qt4"?
    And by the way, why was qt-config removed?
    Last edited by Rulatir (2009-01-11 11:14:19)

    Because KDE 4.0 is just around the corner, qt4 from [community] will be moved to [extra] as qt. qt (3.3.8) will then be renamed to qt3 (still in [extra]).
    http://archlinux.org/pipermail/arch-dev … 02910.html
    As for the QT4 compilation, you won't need the qt-config anymore because qt4 is the "default" qt.
    $ which qmake
    /usr/bin/qmake
    $ qmake -v
    QMake version 2.01a
    Using Qt version 4.3.2 in /usr/lib
    For Qt4 compilation:
    source /etc/profile.d/qt4.sh
    qmake (I explicitly use the /usr/bin prefix though)
    make
    For Qt3:
    source /etc/profile.d/qt.sh
    ${QTDIR}/bin/qmake
    make

  • Anyconnect config problem

    Hey guys,
    I need a little help.  I am able to connect through the anyconnect with no problem.  I can browse to file shares, but when I try to open a web page hosted on our internal server it is never able to load it.  I am attaching my config in hopes someone can spot what I have missed.
    Thanks for any help you can provide,
    Brandon

    Hi,
    The configurations seems a bit confusing to me.
    I mean the following things
    VPN configurations configured under some sort of default tunnel-groups
    NAT0 ACL "106" for the "inside" interface seems to contain alot of lines that to my understanding dont do anything Some source networks are not behind the "inside" interface at all
    The Split tunnel ACL "acl-out" seems to also contain random networks also
    Can you confirm what you use the VPN Client connection for? Is it only for connecting to the LAN behind the ASA? Or is there perhaps some connections that you take from the VPN Client to some networks behind the L2L VPN connections configured on the ASA?
    If possible I would recomend going through the whole VPN configuration and simplifying it (With regards to the AnyConnect configurations)
    I suppose you are using DNS/URL to connect to the Web servers from the VPN Client? You seem to be using Internal DNS servers for the VPN Clients so the DNS replies should be coming from there in that case. Are you sure that this problem isnt related to perhaps your VPN Client getting the wrong IP address with the DNS reply from the LAN server? Have you checked the logs through ASDM while you have attempted the connections to the web servers and seen what happens to the attempts?
    Can you also provide specific IP addresses related to the connection attempts?
    - Jouni

  • Xfree 86 config problem.

    Hi,
    We are building a J2SE on our ARM (Samsung S3C2410 ) system, where the Linux version is MiziLinux.
    Having already installed the J2SE for ARM into the system, we discovered that a X Window Server is needed to show images when running a JAVA application.
    We tried XFree86, but found it is very difficult to write the config file, the 'XF86Config'. The problem is that we don't know how to config the display device and the driver items. The related section of the 'XF86Config' on Redhat 9.0 is like the following:
    Section "Monitor"
         Identifier "Monitor0"
         VendorName "Monitor Vendor"
         ModelName "MAG 770PF"
         DisplaySize 320     240
         HorizSync 30.0 - 70.0
         VertRefresh 50.0 - 160.0
         Option     "dpms"
    EndSection
    Section "Device"
         Identifier "Videocard0"
         Driver "i810"
         VendorName "Videocard vendor"
         BoardName "Intel 845"
         VideoRam 16384
    EndSection
    Section "Screen"
         Identifier "Screen0"
         Device "Videocard0"
         Monitor "Monitor0"
         DefaultDepth 24
         SubSection "Display"
              Depth 24
              Modes "1024x768" "800x600" "640x480"
         EndSubSection
    EndSection
    But for the CPU, ARM S3C2410, the displayer device is a build-in hardware component, therefore, there is no display card at all.
    Any body has the experience of writing such a config file?
    Thanks!

    If you're running JVM 1.4, you can make use of "-Djava.awt.headless=true" to let the JVM know that it is running on a headless machine. Otherwise you can use Xvfb virtual framebuffer and make the JVM display to it. Here is a nice article with good tips on running Java headless: http://developers.sun.com/solaris/tech_topics/java/articles/awt.html

  • AD DS Config problem (The AAAA record for this DC was not found) Cannot connect to ADUC

    I am trying to figure out what is wrong with my AD DS Config. I ran dcdiag. The results were:
    C:\Users\Administrator>dcdiag /test:dns
    Directory Server Diagnosis
    Performing initial setup:
       Trying to find home server...
       Home Server = R210_1_2K12
       * Identified AD Forest.
       Done gathering initial info.
    Doing initial required tests
       Testing server: Default-First-Site-Name\R210_1_2K12
          Starting test: Connectivity
             ......................... R210_1_2K12 passed test Connectivity
    Doing primary tests
       Testing server: Default-First-Site-Name\R210_1_2K12
          Starting test: DNS
             DNS Tests are running and not hung. Please wait a few minutes...
             ......................... R210_1_2K12 passed test DNS
       Running partition tests on : Schema
       Running partition tests on : Configuration
       Running partition tests on : bcas-tbf
       Running enterprise tests on : bcas-tbf.local
          Starting test: DNS
             Test results for domain controllers:
                DC: R210_1_2K12.bcas-tbf.local
                Domain: bcas-tbf.local
                   TEST: Basic (Basc)
                      Warning: The AAAA record for this DC was not found
                   TEST: Records registration (RReg)
                      Network Adapter [00000017] Hyper-V Virtual Ethernet Adapter:
                         Warning:
                         Missing AAAA record at DNS server 172.16.0.202:
                         R210_1_2K12.bcas-tbf.local
                         Warning:
                         Missing AAAA record at DNS server 172.16.0.202:
                         gc._msdcs.bcas-tbf.local
                         Warning:
                         Missing AAAA record at DNS server ::1:
                         R210_1_2K12.bcas-tbf.local
                         Warning:
                         Missing AAAA record at DNS server ::1:
                         gc._msdcs.bcas-tbf.local
                   Warning: Record Registrations not found in some network adapters
                   R210_1_2K12                  PASS WARN PASS PASS PASS WARN n/a
             ......................... bcas-tbf.local passed test DNS
    IPCONFIG info:
    C:\Users\Administrator>ipconfig /all
    Windows IP Configuration
       Host Name . . . . . . . . . . . . : R210_1_2K12
       Primary Dns Suffix  . . . . . . . : bcas-tbf.local
       Node Type . . . . . . . . . . . . : Hybrid
       IP Routing Enabled. . . . . . . . : No
       WINS Proxy Enabled. . . . . . . . : No
       DNS Suffix Search List. . . . . . : bcas-tbf.local
    Ethernet adapter vEthernet (Broadcom BCM5716C NetXtreme II GigE (NDIS VBD Client
    ) #36 - Virtual Switch):
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Hyper-V Virtual Ethernet Adapter #2
       Physical Address. . . . . . . . . : 00-26-B9-7E-81-74
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
       Link-local IPv6 Address . . . . . : fe80::bda9:1a28:974a:5fc3%19(Preferred)
       IPv4 Address. . . . . . . . . . . : 172.16.0.202(Preferred)
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Default Gateway . . . . . . . . . : 172.16.0.1
       DHCPv6 IAID . . . . . . . . . . . : 335554233
       DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1A-0A-52-45-00-26-B9-7E-81-75
       DNS Servers . . . . . . . . . . . : ::1
                                           172.16.0.202
       NetBIOS over Tcpip. . . . . . . . : Enabled
    Tunnel adapter isatap.{AE70C63E-0A8A-4461-A789-8E4CD99CEA46}:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Microsoft ISATAP Adapter
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
    Tunnel adapter Local Area Connection* 11:
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
       Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
       DHCP Enabled. . . . . . . . . . . : No
       Autoconfiguration Enabled . . . . : Yes
       IPv6 Address. . . . . . . . . . . : 2001:0:9d38:90d7:1cf5:1d4f:53ef:ff35(Pref
    erred)
       Link-local IPv6 Address . . . . . : fe80::1cf5:1d4f:53ef:ff35%15(Preferred)
       Default Gateway . . . . . . . . . : ::
       NetBIOS over Tcpip. . . . . . . . : Disabled
    I'm unsure of what the problem is or what to do next.  Thank You.

    Disable IPv6 according to Pauls blog:
    Disabling
    IPv6 on Windows 2008
    After disabling run:
    ipconfig /flushdns
    ipconfig /registerdns
    restart the netlogon service or reboot.
    For co-existence from IPv4 and IPv6 see: 
    Configuring DNS for IPv6/IPv4
    Coexistence
    IPv6
    for the Windows Administrator: How Name Resolution Works in a Dual IPv4/IPv6 Scenario
    IPv6 for the Windows Administrator: IPv6 Fundamentals
    Hopefully, that fixes your issue.  Added some links to read in cause you want to.
    If it answered your question, remember to “Mark as Answer”.
    If you found this post helpful, please “Vote as Helpful”.
    Postings are provided “AS IS” with no warranties, and confers no rights.
    Active Directory: Ultimate Reading Collection

Maybe you are looking for

  • CUCM 8.6 TSP issue

    Hi, I've trouble making the TSP connection to a CUM 8.6 cluster. I am using windows 7 64 Bit PC and installed the "CiscoTSPx64.exe" as a fresh, did a reboot and configured the required paramenters (CTI Server/Username PWD). When I use dialer.exe, I d

  • Question About Import Transport_Tablespace

    I went through import transport_tablespace help there writen in compitable heading that source and target hardware must be same my question is if i run export command on pentium III and import on Pentium4 will it not work and 2nd question is in sourc

  • Restoring from iCloud backup - what happens to non-iTunes music?

    iPhone4, iOS5 and want to restore from an iCloud backup.  Wondering what happens when music not purchased on iTunes (95% of my collection), when I restore from that backup?  I'm thinking it will all be gone and I will have to go through the painful p

  • Missing Codec in iTunes 10.4?

    Greetings, I have several movies that I copied from VHS and converted to Quicktime last winter that played in an older version of iTunes within Snow Leopard. Now that I have upgraded to Lion, they will no longer play in iTunes. I could convert them o

  • Trouble with sudo

    Hello, i have some trouble with the installation of sudo... after the installation i got this message: $ sudo su - root ld.so.1: sudo: fatal: libintl.so.8: open failed: No such file or directoryso i read a post here about it and installed the library