3G Pen detected but not connecting

Hello Everyone,
Today I recieved a 3G Usb PEN and tried to install it and make it work on Arch Linux (It's a Huawei E173s), the pen was detected but there was no connection. I've tried a lot of configuration, but since I don't really know if the apn was right, I tried to connect and old 3G Pen (a Huawei E220).
And then tried to connect. Network Manager (here in Gnome3), show me that it was trying to connect but then fail.. And I really don't know why :S...
This is the log from /var/log/daemon.log :
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> Activation (ttyUSB0) starting connection 'Clix Omissão'
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> (ttyUSB0): device state change: disconnected -> prepare (reason 'none') [30 40 0]
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled...
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started...
Feb 15 12:31:06 localhost NetworkManager[2022]: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete.
Feb 15 12:31:17 localhost NetworkManager[2022]: <warn> GSM connection failed: (32) Sending command failed: 'Resource temporarily unavailable'
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> (ttyUSB0): device state change: prepare -> failed (reason 'unknown') [40 120 1]
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> Marking connection 'Clix Omissão' invalid.
Feb 15 12:31:17 localhost NetworkManager[2022]: <warn> Activation (ttyUSB0) failed.
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> (ttyUSB0): device state change: failed -> disconnected (reason 'none') [120 30 0]
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> (ttyUSB0): deactivating device (reason 'none') [0]
Feb 15 12:31:17 localhost NetworkManager[2022]: nm_system_iface_flush_routes: assertion `ifindex > 0' failed
Feb 15 12:31:17 localhost NetworkManager[2022]: nm_system_iface_flush_addresses: assertion `ifindex > 0' failed
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS.
Feb 15 12:31:17 localhost NetworkManager[2022]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS.
How can I solve this problem ?
Thanks in advance,
Luis Da Costa

Is this anything to do with this
https://bbs.archlinux.org/viewtopic.php?id=118746

Similar Messages

Help! My Zen Micro is detected but not connected to zen media explorer & mediasou

Hi
recently i just bought a creative zen micro at 5 GB. after installing all the drivers and programs using the installation CD that came with my player, I connected my player through the USB cable to my pc USB root hub.
an auto-detect of my zen micro window pops up at the righthand corner, prompting me to click 'organize' in the creative media source. clicking the organize option, mediasource program starts but while it is loading the music library, an error message: CTCMS, The program has performed a illegal operation......etc.
i tried disconnecting my player followed by opening the media source prog and connecting my player after that. another error message: file operation failed. please ensure that your player is properly connected.
I'm using windows 98 SE on an AMD processor. i was able to use the removable disk mode of my player to store data from pc. However when comes to the media mode of my player, it is shown as not connected status in the zen micro media explorer and in the creative media source program, it's either shown as not properly connected or illegal operation when loading music library from my player. in addition, under the device manager, the creative zen micro driver is shown as working properly. i was also able to upgrade my firm ware to version .02.05. using my pc to connect to my player. However, even before upgrading the firmware, this problem is already present. i have contacted the creative technical support helpdesk for advise on this issue and they have suggested to me various solutions such as checking my drivers if they are updated, reinstalling the drivers and software applications for the media library, installing jet engine service pack for my windows and the MDAC component but still nothing works.
anyone have any suggestions? pls help
thanks
Message Edited by fanaticpat on <SPAN class=date_text>05-30-2005 <SPAN class=time_text>0:20 PM
Message Edited by fanaticpat on 05-30-2005 0:2 PM

Hi,
Sorry I can't help you. I just wanted to let you know I have the same exact problem. It started three days ago and I've been going back and forth with creative support and nothing has worked. I am beginning to grow really distressed. I feel a little better now because after seeing that it's happening with someone else, it is most likely not the player. I am running windows 98 SE as well. I also have an AMD Duron processor. I have a new computer on the way with windows XP I really hope it works. But now I have a new problem. I listed it on the front page of this forum a few minutes ago. My player froze and now only boots up in rescue mode. I am getting so frustrated with my player. If you figure anything out will you be as kind as to send me a message on how you got your player working again? I would really appreciate it. Thanks.
Nick
Message Edited by nichols088 on <SPAN class=date_text>06-09-2005 <SPAN class=time_text>05:33 PM
Message Edited by nichols088 on 06-09-2005 05:35 PM

D-Link DIR-615/Macbook detecting but not connecting

This is my first post on the forum.
So I went on a vacation back in January for about a week, but during that week I unplugged my D-Link DIR-615 Wireless N router and modem (Toshiba, Time Warner), just so I wouldn't have people attempting to connect to it for any reason by any means. Fair enuf, right?
I get home, connect the mac, modem, router. Airport will detect the network, but will not "transmit" the internet, won't pull up any webpages.
Any ideas? I've checked the through some of the other posts, but it's kind of hit and miss.

This is because your Mac is connecting to your router but is failing to obtain an IP address via DHCP.
Is your Mac still set up to obtain an address automatically via DHCP?
If so, try the following sequence:
1) Disconnect from your D-Link
2) Power off the cable modem and router.
3) Power on the cable modem and wait until its status lights indiciate it is connected to its network.
4) Power on the D-Link and wait until its status lights state it is connected.
5) Try to reconnect to the D-Link on your Mac.

TS2370 My iPhone detects my my Belkin G5 series wifi router but not connecting, I searched in internet and found many people have similar experience. Please tell , how can I fix it?.

My iPhone detects my my Belkin G5 series wifi router but not connecting, I searched in internet and found many people have similar experience. Please tell , how can I fix it?.

Try rebooting the router. Just remove the power for a few seconds. No settings are lost.

IPhone Detected But Not Identified?

I hooked up my iPhone to my base that goes into my cpu and I got this message: "An iPhones was detected, but could not be identified properly. Please disconnect and reconnect the iPhone and try again." I havent had any problems like this before. Will a reinstall over this iTunes fix the problem? I am running Windows XP. I have also noticed that when I plug up my phone, the Scanner and Camera Wizard pops up recognizing the iPhone as a camera. Also when running iTunes after I got that message, my cpu will freeze for about 5 seconds and work fine a little while then freeze again for 5 seconds. But when I close iTunes, it stops freezing.

I am having the same issue iPhone detected, but not identified. Did you get a solution to the problem? Had to go to th Apple store to register my phone. iPhone connected fine with their MacBook. That doesn't help me at home though.

Ipod is detected but cannot connect

ipod is detected but not connected

Error 1604
This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
Restore and wait for the error.
When prompted, click OK.
Close and reopen iTunes while the device remains connected.
The device should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
Error 1600, 1601, 1602
Follow the steps listed above for Error 1604. This error may also be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.

Bluetooth Set Up But Not Connected Blackberry vCards

Problem: I'm trying to send vCards to my new Blackberry Pearl 8120, but cannot get the mac to send the file to the Bluetooth phone.
1. Bluetooth connectivity IS turned on in Sharing Preferences.
2. When I run "Set Up Bluetooth Device" it finds the phone, no problem.
But in Bluetooth preferences it lists the phone as "Discoverable" and "Paired" but "not connected."
The only time I've gotten a green light for "connected" is when the set-up was running.
Help!
How do I send vCards to the phone - I DO NOT want to type all this stuff over again, not, in this day and age, should I have to.
Seriously - I've seen other posts on similar subjects all unanswered - Mac Support, where are you?

Attached is a list of HP Airprint enabled printers. Your printer is not on this list. If it is wireless, you can purchase an App from the App Store, which will allow you to print. Printopia and Print Central are two which are recommended, both cost about $9 (US).
http://support.apple.com/kb/ht4356

When i plug in my ipod nano (6th generation) a message comes up saying it's 'detected but not identified' i've spend like all day trying to solve it, uninstalled it, reinstalled it and nothing seems to work..

when i plug in my ipod nano (6th generation) a message on itunes saying the ipod is 'detected but not identified'- i've spent all day trying to fix it and nothing seems to work so i can't sync any songs..

Hello beafraser,
Here's an article to help troubleshoot when your iPod is detected but not identified.
iPod nano: Error message saying that iPod 'could not be identified properly'
http://support.apple.com/kb/ts3218
Hope that helps.
Thank you for visiting Apple Support Communities.
Nubz

Does it matter if the lightning cable is plugged in but not connected to an electrical outlet? Will this drain the ipad battery?

Does it matter if the lightning cable is plugged in but not connected to an electrical outlet? Will this drain the ipad battery? We use an ipad cart at school, and some of the teachers will connect all the ipads up to the cart, but then neglect to power up the cart. The laptop with the cart has already had the battery wrecked because of this (within a two month period), and I am concerned the ipads may have an issue if this continues to happen. I need some reassurance before I make the other teachers paranoid!

ok this one is kind in the gray area for me. I say if it is plugged in to a power up cart but not plugged in to a outlet, then all is is doing is not charing, and of course lossing a charge over time in standby, not really causing any issues. User guide and apple sites say it will drain the battery life.
Important: The iPad battery may drain instead of charge if iPad is connected to a computer that’s turned off or is in sleep or standby mode, to a USB hub, or to the USB port on a keyboard.
however “Battery life” means the time your iPad will run before it must be recharged.
so I think it will be ok, as long as you charge it as usaul it should be fine.
just use these links for and understanding for batteries and the ipad, of course the user guide.

IPod Nano 6th Gen detected but not recognized

Since recently, my IPod is not being recognized by iTunes (11.1.4.62 ). The error says that it is detected but not be identified properly. I went through all the troubleshooting steps including resetting my ipod, re-starting the driver, re-installing iTunes but nothing works. Interestingly, if iTunes is not open, I can see the iPod as a storage device, I can open and browse it. So I assume there is no error with the wire, the iPod itself or the driver. As soon as iTunes gives the above error, it stops being visible as a storage device. How can I fix this?

Aridra,
Thanks very much for this - I had exactly the same problem; went through the same steps to no avail unitl I read your post. Similarly, I uninstalled EVERYTHING Apple on my PC and re-installed. Bingo !! my iPod is now recognised and synched.

SAP MMC Says Dispatcher running but not connected to message server

I installed the ABAP Stack Sneak Preview Netweaver.I see all the relevant NSP entries in my Services file.But when i disconnect my internet I see in SAP MMC that Disptacher says its running but not connected Message Server(turns yellow) and also the SAP gets logged off. Is Internet connection required for running NSP(ABAP System SID)??
If I want to get rid of this internet dependency what settings i need to change ??
My current Message trace file says as follows..
Trace File of Message Server
trc file: "dev_ms", trc level: 1, release: "640"
[Thr 4516] Mon Sep 26 21:51:06 2005
[Thr 4516] systemid   560 (PC with Windows NT)
[Thr 4516] relno      6400
[Thr 4516] patchlevel 0
[Thr 4516] patchno    43
[Thr 4516] intno      20020600
[Thr 4516] pid        4512
[Thr 4516] ***LOG Q01=> MsSInit, MSStart (Msg Server 1 4512) [msxxserv.c   1661]
[Thr 4516] Mon Sep 26 21:51:07 2005
[Thr 4516] MsHttpInit: full qualified hostname = sai
[Thr 4516] HTTP logging is switch off
[Thr 4516] set HTTP state to LISTEN
[Thr 4516] *** I listen to port sapmsNSP (3600) ***
[Thr 4516] *** HTTP port 8100 state LISTEN ***
[Thr 4516] CUSTOMER KEY: >K0201639721<
[Thr 4516] Mon Sep 26 21:52:46 2005
[Thr 4516] MsHttpReadUrl: H-1 url = /sap/public/icf_info/urlprefix (403 Forbidden)
[Thr 4516] Mon Sep 26 21:52:50 2005
[Thr 4516] MsHttpReadUrl: H-1 url = /sap/public/icf_info/logon_groups (403 Forbidden)
Looking for your valuable solutions.. Will definitely reward good points if gets solved
Thanks
Sreeni.

There is now also a Weblog about https://weblogs.sdn.sap.com/pub/wlg/2479 [original link is broken] [original link is broken] [original link is broken] [original link is broken] [original link is broken] [original link is broken] [original link is broken] [original link is broken] [original link is broken] [original link is broken].
Regards
Gregor

What do you do when ipod is detected but not identified?

What do you do when ipod is detected but not identified?

Hi there schnee2,
You may find the troubleshooting steps in the article below helpful.
iPod not recognized in My Computer and in iTunes for Windows
http://support.apple.com/kb/ts1369
-Griff W.

TS2756 I can't get personal hotspot to work on my iPhone 5 I backed up my iPhone 4 them changed over today. It's on but not connecting?

I can't get personal hotspot to work on my iPhone 5 I backed up my iPhone 4 them changed over today. It's on but not connecting?

Hello MYPT,
The following article should be helpful in getting your Pesonal Hotspot working.
iOS: Troubleshooting Personal Hotspot
http://support.apple.com/kb/TS2756
Cheers,
Allen

I'm trying to connect my iPad to my Samsung galaxy s by bluetooth but the ipad will pair with it but not connect and says "its not supported" does anyone know what this means and how I get it to work?

I'm trying to connect my iPad to my Samsung galaxy s by bluetooth but the ipad will pair with it but not connect and says "its not supported" does anyone know what this means and how I get it to work?

iOS devices do not have the BT profiles that support file sharing and othr general functions. See:
iOS: Supported Bluetooth profiles
Basically it support headphones, keyboards, speakers, peer-to-peer gaming

TS3694 iOS: Device detected but not identified properly on iTunes for Windows error 54

iOS: Device detected but not identified properly on iTunes for Windows error 54 my iPhone 4s ois 7.1.2 my pc is windows 8.1 my iTunes ver 11.3.1.2. I cant sync with itunes

Look in your Pictures folder and delete the iPhone Photo Cache.

3G Pen detected but not connecting

Similar Messages

Maybe you are looking for