3rd Monitor

I was wondering if I could hook up a 3rd monitor to my mac G5 PowerPC (sounds ancient doesn't it...lol) but I want it to work independently where I can drag different applications into it....let's say I have safari, Logic, and reason?

This will depend upon your hardware setup, in particular your video cards. There was a recent question about this on the PPC hardware forums and I suggest this post be moved there since it is more a hardware question. I can request it be moved if you like. My initial thought is are there cards that have 3 video outputs? If not, you will require a separate video card for the third monitor.

Similar Messages

Video card to run 2nd and 3rd monitors cs5.5

Hello all,
I have a powerful system with multiple hard drives that I use to cut HD DSLR footage on in CS5.5. My GTX 570 runs my 1st monitor and my 9600GT runs the 2nd and 3rd monitors with great success.
1st monitor = timeline
2nd = bins
3rd = full screen preview (Highest quality preview)
The reason I use the gtx 570 to run only the first monitor is because it idles much higher and hotter connected to two monitors. (Disables the down clocking feature on the card when connected to multiple displays).
Well the 9600gt has died.
I don't want to spend alot of money here but I am not sure what video card I require for my 2nd and 3rd monitors. Keep in mind the 3rd monitor is the full screen preview.
I know premiere pro uses my 570gtx for the MPE but I have no idea how this effects (if it does at all) my 3rd preview monitor since I have had it plugged into my 9600gt.
There for I am not sure if I can get away with a cheap card like a $50.00 Nvidia GT 610 or do I need something at least equal or greater then my old 9600gt?
Thanks!,
Kieran

Thank you for the reply Harm. I have an x79 board with a 3930k @ 4.6ghz.
I will take that advice on board.. I might have to fork out a bit of extra money. Shame I only purchased the 570 gtx a couple of months ago!
Found this card....
Gainward GTX550Ti 1G DDR5 DVI HDMI
Internet Price:    $111.00
Barcode :
426018336-2050
GPU :
GeForce GTX 550 Ti
GPU Clockspeed :
900 Mhz
Memory :
1024MB GDDR5 192bits
Memory Clockspeed :
2050 Mhz
Pixels per clock (peak) :
N/A
Bandwidth :
98.4 GB/s
Ramdac :
400 MHz
PCI-Express 2.0
Cooling :
2-Slot Fan
Video-Features :
HDMI
Connectivity :
DVI-I + VGA
Would this be sufficient??
Thanks!!
Kieran

HD2600XT w/X1900XT for 3rd monitor - systems freezes

I wanted to add a 3rd monitor to my early MacPro that came with the Radeon X1900 XT. I asked and received advice in an earlier post concerning a graphics card that would be compatible with my configuration. The Radeon HD2600XT was an affordable suggestion. I next called the Apple Store and asked them to confirm compatibility. They transferred me to tech support who made the assurance that the 2600XT would work. I conveyed the info to my wife who ordered it for me for Xmas from Apple.
Well, today is Xmas. I installed the card in slot 3, connected the 3rd monitor, and started up. It worked! For about 5 or 10 minutes, until I got into some applications. Then the system froze. I had power over the mouse but nothing else.
I reset the MMR, I zapped the PRAM, I changed the HD2600XT to slot 2, but every time I checked the graphics card in the system profiler, status of the graphics card was "No display connected." I switched monitors, I took all of the monitors off except the one connected to the HD2600XT - I tried this with multiple monitors. Even though the monitor would work for a while before freezing again, any monitor connected to the 2600XT would produce the same message in system profiler - "No display connected." BTW, in froze in many different applications, in case you were wondering.
I called Apple back. Now they are not certain that the X2600 XT is compatible. Now they tell me that the only one they are sure of is the nVidia Quadro FX 4500 - a NOT so affordable alternative. (Found one for "as cheap as" $535).
Can anyone confirm that the Radeon X1900 (which will only operate in slot 1) is compatible with the Radeon HD2600 XT, or vice versa, in an early MacPro (one year old today) - absolutely? Do you suppose Apple will take the 2600 back if it is not? (Do I have a bad card right out of the box? Did I miss anything? Is there anything else I can try? I hesitate to ask this last question but do you think it is the logic board. Everything works fine with the X1900 and 2 monitors so I don't see why it would be the logic board...

Hi,
I'm running a Mac Pro 1.1 quad 2.66 with 12GB of memory and a X1900XT with a HD2600XT. The X1900XT is driving two dell 24" monitors at 1920x1200 and the HD2600XT is driving a HD projector at 1280x768. I have the X1900XT in the bottom slot at 16x and the HD2600XT in the top slot at 8x.
I don't think the lanes are the issue. 1x would be MORE than enough to allow for 2D rendering such as browsing the web. PCIe v1.x is 250MBps per channel (PCIe 2.0 is 500MBps). Let us assume you are running a 1920x1200 desktop and you are watching a full screen video that is using the whole space and it being displayed at 30fps and all textures are changing with each frame. So that would be 1920x1200x32x30 (x by y times bit-depth (millions of colors is 32 bit) times redraw) which works out to be 2,211,840,000 bits, so you divide that by 8 to get bytes, 276,480,000, divide again by 1024 to be KB, 270,000, divide again by 1024 to get MB, which works out to be 263.67 MBps. So you might get a few dropped frames worse case scenario with a 1x channel. However, if you are running 8x you have 1,000MBps to work with which you will never use all of in a 2D draw even with a 30" display at 2560x1600 which would work out to be 468.75MBps. The reason you need the large bandwidth is for things like games where you are not rendering flat 2D textures. 3D textures can go through memory and thus bandwidth quick as you have added a whole-nother axis to the equation.
I don't think power is the issue either. The 300 watts, is 300 watts from the PCIe bus and not the motherboard per say. The X1900XT has an external power molex serving it power there by supplementing it's pull off the bus. The HD2600XT is low enough it doesn't need external power. More over, the reason that the 1900 has external power is that one slot is not allowed to pull more than a certain amount of power, I believe 60 watts, per slot. So with two cards that's only 120 of the 300 watts.
I believe you may have one of the following:
1) A heating issue, especially if you are still running the stock heatsink on the 1900 (it gets HOT, which is why I think the 1900s are having so many issues in the Macs) and the issue may have been triggered by adding the extra heat from the 2600.
2) You could have a hardware issue with either the 2600 or the motherboard. Trying another slot may help with testing the motherboard, testing the 2600 could be a bit more difficult. (I think that's been suggested.)
3) Could be a firmware issue and that could be any number of combination between the firmware on the Mac and the two video cards.
What kind of monitor do you have and are you serious about selling it?
Best of luck!

3rd monitor issues.....

I have an iMac 24 inch Mid-2007 model. It has a View Sonic 24 inch monitor connected to it. My iMac monitor is leaving a ghost image so I've been told that I can hook up a third monitor and just ignore the iMac monitor and use the 2 attached View Sonic monitors.
Now I'm told that my iMac can't handle a 3rd monitor.
Is there a way around this or is my iMac just to old? He told me that I can only run a 3rd montior if I had the new 27 inch iMac.
I was trying to save some $$ on buying a new Mac right now, which is why I was doing this in the first place.
ANY advice since I can't return the View Sonic monitor I just bought....
This is the view sonic that I have...
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=60525 09&csid=_61
OR
If I was to buy a mac mini, what kind would I need to purchase that would allow 2 monitors?

Sally,
Your machine is too old unfortunately to support 3 displays. I would recommend either repairing or replacing your iMac, it's 5+ years old so it may have reached the end of it's useful life. You can still use the external display but if you want 2 displays at the moment there is no either solution.

Adding a 3rd Monitor to a Power Mac G5

I am curious as to how - and if - I can add a 3rd monitor to my G5.
Currently I have an ATI 9650 Graphics Card and it runs my 2 23" CD wonderfully. I have been considering adding a 3rd monitor if possible and getting a 30" to have in the middle of the 23's.
Does anyone have knowledge or experience in doing this. It doesn't necessarily have to be a 30 in the middle, another 23 would suffice.
Thanks in advance!!!

To my knowledge, the ATI 9600 PCI is currently the only PCI based
video card that can be used in the g5
This turns out not to be the case. Any 3.3 volt PCI card will operate in a G5 PCI slot. This should include Radeon 7000, 9000, and 9200 PCI cards. I'm using a PCI Raedon 7000 in my G5 this moment. With my 2-head 9600, I can run 4 displays.
7000 PCI = VGA + DVI
9600 AGP = ADC + DVI
I am skeptical that any PCI card has an ADC port. The PCI 2.x spec doesn't provide for powering an ADC monitor, so I suspect an ADC display can be driven from only an Apple-AGP slot or a standard PCI-Express slot.

How can i add a 3rd monitor to my brand new macbook with thunderbolt?

I have just bought a new 13" macbook pro and already have one screen attached. How can I add a 3rd. I'm told it is capable of running several at once???

You can add a third display using a USB video adapter such as this:
http://eshop.macsales.com/item/NewerTech/VIDU2DVIA/
Note that video performance on a USB-connected monitor is limited by the slowness of the USB connection. Such a monitor won't be suitable for gaming or fast-action video, but will be fine for business applications, basic photo editing, etc.

VIDEO I/O - 3RD MONITOR

Hi,
I'm just about to put together my new edit suite, but I'm stuck on the issue of the 3rd graded monitor.
First of all, it would probably help if I told you the footage we're editing is 720p25 shot in the Panasonic HVX200 (P2 cards, not tape)
In addition to the two standard monitors, I would like a third graded HD monitor and output to a SD source.
I was going to buy the Blackmagic Intensity Pro card, which I was told would do the job, but according to their website it doesn't support 720p25, only 720p50 or 59.94.
The alternative was the Matrox Mini, however, this doesn't support 720p25 either.
A couple of people have suggested I get two graphics cards, but most have warned that this is not the best solution.
This is one of the most common aspects of video editing (a third graded monitor) so there must be an answer, I just can't find it!!
Does anybody have any ideas;
Is there another card on the market?
Is there a suitable graphics card that also has a third video out?
Has anyone got a black magic or matrox mini and uses it for 720p25 output?
Any help would be terrific.
Cheers
Ben

ATI HD58xx cards have three outputs and the EyeFinity expected in a couple of weeks even 6 HDMI connections. The dilemma is that ATI will not be supported (at least not yet) for use with MPE. That will only work with a limited number of nVidia cards, that only allow 2 monitors.
In addition to the two standard monitors, I would like a third graded HD
monitor and output to a SD source.
I understand output to a destination, but output to a source? I thought it was input from a source.
Anyway, if I understand you correctly, you want a third SD capable monitor. In that case a firewire out to a camera/deck with analog out to a monitor/TV will do the job.

Setting up 3rd monitor on H50-50

When I Install a GeForce 210 graphics card, I get video only on the monitor connected to it. Tried IGD, PEG and auto video options.
Another oddity: I can't access the setup utility via F1 with the card installed. Is the BIOS defective?
How can I get both graphics systems to work so I can get 3 or 4 monitors?

hi Konzeled,
Welcome to Lenovo Community Forums!
This system will only support the following
IGP : Integrated Display which is the Intel HD
PEG: PCI Graphics which is your GE force
Auto: Will Auto select the graphics between the Two upon boot.
The system does not support SLI or XFire since it only have one PCI x 16 Port which you already utilize with the GE Force Card.
Hope this helps
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Connecting a 3rd Monitor to a G5...

Hi. I have 2 monitors connected to my g5. Does anyone know what i need to buy in order to connect a third monitor? Thanks, Ben

http://froogle.google.com/froogle?hl=en&q=pci%20mac%20video%20card&btnG=Google+S earch&sa=N&tab=wf
http://froogle.google.co.uk/froogle?q=macpci+video+card&btnG=SearchFroogle&hl=en

Photoshop crashing when my 3rd monitor is on (3rd monitor uses Integrated Graphics)

So as I said in the title, when my third monitor is on (which is hooked up to my i5's integrated graphics photoshop crashes a lot. When I go to my Device Manager and disable it, photoshop workes flawlessly.
My main videocard is a Radeon 6970 2gb, so it has no problems running photoshop alone. The processor seems to just get in the way. Any way around this?

If you read Adobe Site about GPU support you will read you can not mix display adapters. It is posible to hook all three of your displays to your 6970.
http://helpx.adobe.com/photoshop/kb/photoshop-cs6-gpu-faq.html#id_97496
http://www.amd.com/us/products/technologies/amd-eyefinity-technology/how-to/Pages/set-up.a spx
http://www.amd.com/us/Documents/AMD_FirePro_W600_Datasheet.pdf
http://pcwizkidstechtalk.com/index.php/amd-eyefinity-tutorial.html

Issues with using 3 monitors on 2 external gpu

Hi,
I have some issues with configuring Xorg to use 3 monitors. I have 2 external graphic cards (same model, no SLI). Monitors connected to the first gpu are recognized ok but I can't configure my 3rd monitor conencted to the second gpu via HDMI nor DVI.
1st is recognized as DVI-I-1, 2nd is DP-1 in first card, 3rd monitor is in second card (bus 22:00.0) as DP-1-2 (also tried connecting as DVI-I-2). I can see them in Xorg log but I can't configure my 3rd monitor via kscreen nor xrandr. :-/
lspci |grep VGA:
03:00.0 VGA compatible controller: NVIDIA Corporation GF108GL [Quadro 600] (rev a1)
22:00.0 VGA compatible controller: NVIDIA Corporation GF108GL [Quadro 600] (rev a1)
xrandr:
Screen 0: minimum 320 x 200, current 3840 x 1080, maximum 8192 x 8192
DVI-I-1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 527mm x 297mm
1920x1080 60.0*+
1600x900 60.0
1280x1024 75.0 60.0
1152x864 75.0
1024x768 75.1 60.0
800x600 75.0 60.3
640x480 75.0 60.0
720x400 70.1
DP-1 connected 1920x1080+1920+0 (normal left inverted right x axis y axis) 527mm x 297mm
1920x1080 60.0*+
1600x900 60.0
1280x1024 75.0 60.0
1152x864 75.0
1024x768 75.1 60.0
800x600 75.0 60.3
640x480 75.0 60.0
720x400 70.1
Xorg config (autoconfig enable only 2 monitors, I generated config and tried to edit it with no luck, I noticed there is PCI:34:0:0 generated by Xorg so I also tried to change it to 22:0:0, I also tried to add that option "Monitor-<output>" but same result):
Section "ServerLayout"
Identifier "X.org Configured"
#Screen 0 "Screen0" 0 0
#Screen 1 "Screen1" RightOf "Screen0"
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/OTF/"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/100dpi/"
FontPath "/usr/share/fonts/75dpi/"
EndSection
Section "Module"
Load "glx"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "DELL"
Option "Monitor-DVI-I-1" "DVI-I-1"
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "DELL"
Option "Monitor-DP-1" "DP-1"
EndSection
Section "Monitor"
Identifier "Monitor2"
VendorName "DELL"
Option "Monitor-DP-1-2" "DP-1-2"
EndSection
Section "Device"
Identifier "Card0"
Driver "nouveau"
BusID "PCI:3:0:0"
Option "Monitor-DVI-I-1"
Option "Monitor-DP-1"
EndSection
Section "Device"
Identifier "Card1"
Driver "nouveau"
BusID "PCI:34:0:0"
Option "Monitor-DP-1-2"
EndSection
Xorg log (I can see that monitor at time 1767.316):
[ 1766.959]
X.Org X Server 1.14.5
Release Date: 2013-12-12
[ 1766.960] X Protocol Version 11, Revision 0
[ 1766.960] Build Operating System: Linux 3.12.5-1-ARCH x86_64
[ 1766.960] Current Operating System: Linux CZ09DT1XM5002 3.12.5-1-ARCH #1 SMP PREEMPT Thu Dec 12 12:57:31 CET 2013 x86_64
[ 1766.960] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=e2c593e5-b0f4-4c74-84fd-5a88db345ca4 rw quiet
[ 1766.961] Build Date: 13 December 2013 03:11:42PM
[ 1766.962]
[ 1766.962] Current version of pixman: 0.32.4
[ 1766.963] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 1766.963] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 1766.965] (==) Log file: "/var/log/Xorg.1.log", Time: Thu Jan 2 12:43:56 2014
[ 1766.965] (++) Using config file: "/etc/X11/xorg.conf.d/20-multimonitor.conf"
[ 1766.966] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 1766.966] (==) ServerLayout "X.org Configured"
[ 1766.966] (==) No screen section available. Using defaults.
[ 1766.966] (**) |-->Screen "Default Screen Section" (0)
[ 1766.966] (**) | |-->Monitor "<default monitor>"
[ 1766.966] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 1766.966] (**) | |-->Device "Card0"
[ 1766.966] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 1766.966] (**) |-->Input Device "Mouse0"
[ 1766.966] (**) |-->Input Device "Keyboard0"
[ 1766.966] (==) Automatically adding devices
[ 1766.966] (==) Automatically enabling devices
[ 1766.966] (==) Automatically adding GPU devices
[ 1766.966] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 1766.966] Entry deleted from font path.
[ 1766.966] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 1766.966] Entry deleted from font path.
[ 1766.966] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 1766.966] Entry deleted from font path.
[ 1766.966] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 1766.967] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 1766.967] Entry deleted from font path.
[ 1766.967] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 1766.967] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 1766.967] Entry deleted from font path.
[ 1766.967] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 1766.967] Entry deleted from font path.
[ 1766.967] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 1766.967] Entry deleted from font path.
[ 1766.967] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 1766.967] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 1766.967] Entry deleted from font path.
[ 1766.967] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 1766.967] (**) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 1766.967] (**) ModulePath set to "/usr/lib/xorg/modules"
[ 1766.967] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 1766.967] (WW) Disabling Mouse0
[ 1766.967] (WW) Disabling Keyboard0
[ 1766.967] (II) Loader magic: 0x7fec20
[ 1766.967] (II) Module ABI versions:
[ 1766.967] X.Org ANSI C Emulation: 0.4
[ 1766.967] X.Org Video Driver: 14.1
[ 1766.967] X.Org XInput driver : 19.1
[ 1766.967] X.Org Server Extension : 7.0
[ 1766.967] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 1766.967] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 1767.169] (--) PCI:*(0:3:0:0) 10de:0df8:10de:0835 rev 161, Mem @ 0xc6000000/16777216, 0xc8000000/134217728, 0xd0000000/33554432, I/O @ 0x00007000/128, BIOS @ 0x????????/524288
[ 1767.169] (--) PCI: (0:34:0:0) 10de:0df8:10de:0835 rev 161, Mem @ 0xfa000000/16777216, 0xf0000000/134217728, 0xf8000000/33554432, I/O @ 0x0000f000/128, BIOS @ 0x????????/524288
[ 1767.169] Initializing built-in extension Generic Event Extension
[ 1767.170] Initializing built-in extension SHAPE
[ 1767.170] Initializing built-in extension MIT-SHM
[ 1767.170] Initializing built-in extension XInputExtension
[ 1767.171] Initializing built-in extension XTEST
[ 1767.171] Initializing built-in extension BIG-REQUESTS
[ 1767.172] Initializing built-in extension SYNC
[ 1767.172] Initializing built-in extension XKEYBOARD
[ 1767.172] Initializing built-in extension XC-MISC
[ 1767.173] Initializing built-in extension SECURITY
[ 1767.173] Initializing built-in extension XINERAMA
[ 1767.174] Initializing built-in extension XFIXES
[ 1767.174] Initializing built-in extension RENDER
[ 1767.174] Initializing built-in extension RANDR
[ 1767.175] Initializing built-in extension COMPOSITE
[ 1767.175] Initializing built-in extension DAMAGE
[ 1767.175] Initializing built-in extension MIT-SCREEN-SAVER
[ 1767.176] Initializing built-in extension DOUBLE-BUFFER
[ 1767.176] Initializing built-in extension RECORD
[ 1767.176] Initializing built-in extension DPMS
[ 1767.177] Initializing built-in extension X-Resource
[ 1767.177] Initializing built-in extension XVideo
[ 1767.177] Initializing built-in extension XVideo-MotionCompensation
[ 1767.178] Initializing built-in extension XFree86-VidModeExtension
[ 1767.178] Initializing built-in extension XFree86-DGA
[ 1767.178] Initializing built-in extension XFree86-DRI
[ 1767.179] Initializing built-in extension DRI2
[ 1767.179] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[ 1767.179] (II) LoadModule: "glx"
[ 1767.179] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 1767.179] (II) Module glx: vendor="X.Org Foundation"
[ 1767.179] compiled for 1.14.5, module version = 1.0.0
[ 1767.179] ABI class: X.Org Server Extension, version 7.0
[ 1767.179] (==) AIGLX enabled
[ 1767.180] Loading extension GLX
[ 1767.180] (II) LoadModule: "nouveau"
[ 1767.180] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 1767.180] (II) Module nouveau: vendor="X.Org Foundation"
[ 1767.180] compiled for 1.14.4, module version = 1.0.10
[ 1767.180] Module class: X.Org Video Driver
[ 1767.180] ABI class: X.Org Video Driver, version 14.1
[ 1767.180] (II) NOUVEAU driver
[ 1767.180] (II) NOUVEAU driver for NVIDIA chipset families :
[ 1767.180] RIVA TNT (NV04)
[ 1767.180] RIVA TNT2 (NV05)
[ 1767.180] GeForce 256 (NV10)
[ 1767.180] GeForce 2 (NV11, NV15)
[ 1767.180] GeForce 4MX (NV17, NV18)
[ 1767.180] GeForce 3 (NV20)
[ 1767.180] GeForce 4Ti (NV25, NV28)
[ 1767.180] GeForce FX (NV3x)
[ 1767.180] GeForce 6 (NV4x)
[ 1767.180] GeForce 7 (G7x)
[ 1767.180] GeForce 8 (G8x)
[ 1767.180] GeForce GTX 200 (NVA0)
[ 1767.180] GeForce GTX 400 (NVC0)
[ 1767.180] (--) using VT number 3
[ 1767.182] (II) [drm] nouveau interface version: 1.1.1
[ 1767.183] (II) [drm] nouveau interface version: 1.1.1
[ 1767.183] (II) Loading sub module "dri2"
[ 1767.183] (II) LoadModule: "dri2"
[ 1767.183] (II) Module "dri2" already built-in
[ 1767.183] (--) NOUVEAU(0): Chipset: "NVIDIA NVC1"
[ 1767.183] (II) NOUVEAU(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 1767.183] (==) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32
[ 1767.183] (==) NOUVEAU(0): RGB weight 888
[ 1767.183] (==) NOUVEAU(0): Default visual is TrueColor
[ 1767.183] (==) NOUVEAU(0): Using HW cursor
[ 1767.183] (==) NOUVEAU(0): GLX sync to VBlank disabled.
[ 1767.183] (==) NOUVEAU(0): Page flipping enabled
[ 1767.183] (==) NOUVEAU(0): Swap limit set to 2 [Max allowed 2]
[ 1767.222] (II) NOUVEAU(0): Output DVI-I-1 has no monitor section
[ 1767.230] (II) NOUVEAU(0): Output DP-1 has no monitor section
[ 1767.265] (II) NOUVEAU(0): EDID for output DVI-I-1
[ 1767.265] (II) NOUVEAU(0): Manufacturer: DEL Model: a09b Serial#: 827608652
[ 1767.265] (II) NOUVEAU(0): Year: 2013 Week: 41
[ 1767.265] (II) NOUVEAU(0): EDID Version: 1.3
[ 1767.265] (II) NOUVEAU(0): Digital Display Input
[ 1767.265] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 53 vert.: 30
[ 1767.265] (II) NOUVEAU(0): Gamma: 2.20
[ 1767.265] (II) NOUVEAU(0): DPMS capabilities: StandBy Suspend Off
[ 1767.265] (II) NOUVEAU(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 1767.265] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 1767.265] (II) NOUVEAU(0): redX: 0.650 redY: 0.338 greenX: 0.320 greenY: 0.613
[ 1767.265] (II) NOUVEAU(0): blueX: 0.154 blueY: 0.061 whiteX: 0.313 whiteY: 0.329
[ 1767.265] (II) NOUVEAU(0): Supported established timings:
[ 1767.265] (II) NOUVEAU(0): 720x400@70Hz
[ 1767.265] (II) NOUVEAU(0): 640x480@60Hz
[ 1767.265] (II) NOUVEAU(0): 640x480@75Hz
[ 1767.265] (II) NOUVEAU(0): 800x600@60Hz
[ 1767.265] (II) NOUVEAU(0): 800x600@75Hz
[ 1767.265] (II) NOUVEAU(0): 1024x768@60Hz
[ 1767.265] (II) NOUVEAU(0): 1024x768@75Hz
[ 1767.265] (II) NOUVEAU(0): 1280x1024@75Hz
[ 1767.265] (II) NOUVEAU(0): Manufacturer's mask: 0
[ 1767.265] (II) NOUVEAU(0): Supported standard timings:
[ 1767.265] (II) NOUVEAU(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 1767.265] (II) NOUVEAU(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 1767.265] (II) NOUVEAU(0): #2: hsize: 1600 vsize 900 refresh: 60 vid: 49321
[ 1767.265] (II) NOUVEAU(0): #3: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 1767.265] (II) NOUVEAU(0): Supported detailed timing:
[ 1767.265] (II) NOUVEAU(0): clock: 148.5 MHz Image Size: 527 x 297 mm
[ 1767.265] (II) NOUVEAU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 1767.265] (II) NOUVEAU(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 1767.265] (II) NOUVEAU(0): Serial No: 36WJX3A91TNL
[ 1767.265] (II) NOUVEAU(0): Monitor name: DELL P2414H
[ 1767.265] (II) NOUVEAU(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 1767.265] (II) NOUVEAU(0): EDID (in hex):
[ 1767.265] (II) NOUVEAU(0): 00ffffffffffff0010ac9ba04c4e5431
[ 1767.265] (II) NOUVEAU(0): 2917010380351e78eaa0a5a656529d27
[ 1767.265] (II) NOUVEAU(0): 0f5054a54b00714f8180a9c0d1c00101
[ 1767.265] (II) NOUVEAU(0): 010101010101023a801871382d40582c
[ 1767.265] (II) NOUVEAU(0): 45000f292100001e000000ff00333657
[ 1767.265] (II) NOUVEAU(0): 4a5833413931544e4c0a000000fc0044
[ 1767.265] (II) NOUVEAU(0): 454c4c205032343134480a20000000fd
[ 1767.265] (II) NOUVEAU(0): 00384c1e5311000a20202020202000c2
[ 1767.265] (II) NOUVEAU(0): Printing probed modes for output DVI-I-1
[ 1767.265] (II) NOUVEAU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 1767.265] (II) NOUVEAU(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 1767.265] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): EDID for output DP-1
[ 1767.273] (II) NOUVEAU(0): Manufacturer: DEL Model: a09a Serial#: 844123724
[ 1767.273] (II) NOUVEAU(0): Year: 2013 Week: 41
[ 1767.273] (II) NOUVEAU(0): EDID Version: 1.4
[ 1767.273] (II) NOUVEAU(0): Digital Display Input
[ 1767.273] (II) NOUVEAU(0): 8 bits per channel
[ 1767.273] (II) NOUVEAU(0): Digital interface is DisplayPort
[ 1767.273] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 53 vert.: 30
[ 1767.273] (II) NOUVEAU(0): Gamma: 2.20
[ 1767.273] (II) NOUVEAU(0): DPMS capabilities: Off
[ 1767.273] (II) NOUVEAU(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 YCrCb 4:2:2
[ 1767.273] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 1767.273] (II) NOUVEAU(0): Preferred mode is native pixel format and refresh rate
[ 1767.273] (II) NOUVEAU(0): redX: 0.650 redY: 0.338 greenX: 0.320 greenY: 0.613
[ 1767.273] (II) NOUVEAU(0): blueX: 0.154 blueY: 0.061 whiteX: 0.313 whiteY: 0.329
[ 1767.273] (II) NOUVEAU(0): Supported established timings:
[ 1767.273] (II) NOUVEAU(0): 720x400@70Hz
[ 1767.273] (II) NOUVEAU(0): 640x480@60Hz
[ 1767.273] (II) NOUVEAU(0): 640x480@75Hz
[ 1767.273] (II) NOUVEAU(0): 800x600@60Hz
[ 1767.273] (II) NOUVEAU(0): 800x600@75Hz
[ 1767.273] (II) NOUVEAU(0): 1024x768@60Hz
[ 1767.273] (II) NOUVEAU(0): 1024x768@75Hz
[ 1767.273] (II) NOUVEAU(0): 1280x1024@75Hz
[ 1767.273] (II) NOUVEAU(0): Manufacturer's mask: 0
[ 1767.273] (II) NOUVEAU(0): Supported standard timings:
[ 1767.273] (II) NOUVEAU(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 1767.273] (II) NOUVEAU(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 1767.273] (II) NOUVEAU(0): #2: hsize: 1600 vsize 900 refresh: 60 vid: 49321
[ 1767.273] (II) NOUVEAU(0): #3: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 1767.273] (II) NOUVEAU(0): Supported detailed timing:
[ 1767.273] (II) NOUVEAU(0): clock: 148.5 MHz Image Size: 527 x 297 mm
[ 1767.273] (II) NOUVEAU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 1767.273] (II) NOUVEAU(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 1767.273] (II) NOUVEAU(0): Serial No: 36WJX3A92PNL
[ 1767.273] (II) NOUVEAU(0): Monitor name: DELL P2414H
[ 1767.273] (II) NOUVEAU(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 1767.273] (II) NOUVEAU(0): EDID (in hex):
[ 1767.273] (II) NOUVEAU(0): 00ffffffffffff0010ac9aa04c4e5032
[ 1767.273] (II) NOUVEAU(0): 29170104a5351e783aa0a5a656529d27
[ 1767.273] (II) NOUVEAU(0): 0f5054a54b00714f8180a9c0d1c00101
[ 1767.273] (II) NOUVEAU(0): 010101010101023a801871382d40582c
[ 1767.273] (II) NOUVEAU(0): 45000f292100001e000000ff00333657
[ 1767.273] (II) NOUVEAU(0): 4a5833413932504e4c0a000000fc0044
[ 1767.273] (II) NOUVEAU(0): 454c4c205032343134480a20000000fd
[ 1767.273] (II) NOUVEAU(0): 00384c1e5311000a2020202020200053
[ 1767.273] (II) NOUVEAU(0): Printing probed modes for output DP-1
[ 1767.273] (II) NOUVEAU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 1767.273] (II) NOUVEAU(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 1767.273] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): Output DVI-I-1 connected
[ 1767.273] (II) NOUVEAU(0): Output DP-1 connected
[ 1767.273] (II) NOUVEAU(0): Using exact sizes for initial modes
[ 1767.273] (II) NOUVEAU(0): Output DVI-I-1 using initial mode 1920x1080
[ 1767.273] (II) NOUVEAU(0): Output DP-1 using initial mode 1920x1080
[ 1767.273] (II) NOUVEAU(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 1767.274] (--) NOUVEAU(0): Virtual size is 1920x1080 (pitch 0)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1920x1080": 148.5 MHz (scaled from 0.0 MHz), 67.5 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 1767.274] (**) NOUVEAU(0): Mode "1600x900": 119.0 MHz (scaled from 0.0 MHz), 55.9 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1280x1024": 135.0 MHz (scaled from 0.0 MHz), 80.0 kHz, 75.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1280x1024": 108.0 MHz (scaled from 0.0 MHz), 64.0 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1152x864": 108.0 MHz (scaled from 0.0 MHz), 67.5 kHz, 75.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1024x768": 78.8 MHz (scaled from 0.0 MHz), 60.1 kHz, 75.1 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "800x600": 49.5 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.5 kHz, 75.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "720x400": 28.3 MHz (scaled from 0.0 MHz), 31.5 kHz, 70.1 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 1767.274] (==) NOUVEAU(0): DPI set to (96, 96)
[ 1767.274] (II) Loading sub module "fb"
[ 1767.274] (II) LoadModule: "fb"
[ 1767.274] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 1767.274] (II) Module fb: vendor="X.Org Foundation"
[ 1767.274] compiled for 1.14.5, module version = 1.0.0
[ 1767.274] ABI class: X.Org ANSI C Emulation, version 0.4
[ 1767.274] (II) Loading sub module "exa"
[ 1767.274] (II) LoadModule: "exa"
[ 1767.274] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 1767.274] (II) Module exa: vendor="X.Org Foundation"
[ 1767.274] compiled for 1.14.5, module version = 2.6.0
[ 1767.274] ABI class: X.Org Video Driver, version 14.1
[ 1767.274] (II) Loading sub module "shadowfb"
[ 1767.274] (II) LoadModule: "shadowfb"
[ 1767.274] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[ 1767.274] (II) Module shadowfb: vendor="X.Org Foundation"
[ 1767.274] compiled for 1.14.5, module version = 1.0.0
[ 1767.274] ABI class: X.Org ANSI C Emulation, version 0.4
[ 1767.274] (II) Loading sub module "dri2"
[ 1767.274] (II) LoadModule: "dri2"
[ 1767.274] (II) Module "dri2" already built-in
[ 1767.274] (--) NOUVEAU(G0): Chipset: "NVIDIA NVC1"
[ 1767.275] (==) NOUVEAU(G0): Depth 24, (--) framebuffer bpp 32
[ 1767.275] (==) NOUVEAU(G0): RGB weight 888
[ 1767.275] (==) NOUVEAU(G0): Default visual is TrueColor
[ 1767.275] (==) NOUVEAU(G0): Using HW cursor
[ 1767.275] (==) NOUVEAU(G0): GLX sync to VBlank disabled.
[ 1767.275] (==) NOUVEAU(G0): Page flipping enabled
[ 1767.275] (==) NOUVEAU(G0): Swap limit set to 2 [Max allowed 2]
[ 1767.308] (II) NOUVEAU(G0): Output DVI-I-1-2 has no monitor section
[ 1767.316] (II) NOUVEAU(G0): Output DP-1-2 has no monitor section
[ 1767.339] (II) NOUVEAU(G0): EDID for output DVI-I-1-2
[ 1767.347] (II) NOUVEAU(G0): EDID for output DP-1-2
[ 1767.347] (II) NOUVEAU(G0): Manufacturer: DEL Model: a09a Serial#: 844124236
[ 1767.347] (II) NOUVEAU(G0): Year: 2013 Week: 41
[ 1767.347] (II) NOUVEAU(G0): EDID Version: 1.4
[ 1767.347] (II) NOUVEAU(G0): Digital Display Input
[ 1767.347] (II) NOUVEAU(G0): 8 bits per channel
[ 1767.347] (II) NOUVEAU(G0): Digital interface is DisplayPort
[ 1767.347] (II) NOUVEAU(G0): Max Image Size [cm]: horiz.: 53 vert.: 30
[ 1767.347] (II) NOUVEAU(G0): Gamma: 2.20
[ 1767.347] (II) NOUVEAU(G0): DPMS capabilities: Off
[ 1767.347] (II) NOUVEAU(G0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 YCrCb 4:2:2
[ 1767.347] (II) NOUVEAU(G0): First detailed timing is preferred mode
[ 1767.347] (II) NOUVEAU(G0): Preferred mode is native pixel format and refresh rate
[ 1767.347] (II) NOUVEAU(G0): redX: 0.650 redY: 0.338 greenX: 0.320 greenY: 0.613
[ 1767.347] (II) NOUVEAU(G0): blueX: 0.154 blueY: 0.061 whiteX: 0.313 whiteY: 0.329
[ 1767.347] (II) NOUVEAU(G0): Supported established timings:
[ 1767.347] (II) NOUVEAU(G0): 720x400@70Hz
[ 1767.347] (II) NOUVEAU(G0): 640x480@60Hz
[ 1767.347] (II) NOUVEAU(G0): 640x480@75Hz
[ 1767.347] (II) NOUVEAU(G0): 800x600@60Hz
[ 1767.347] (II) NOUVEAU(G0): 800x600@75Hz
[ 1767.347] (II) NOUVEAU(G0): 1024x768@60Hz
[ 1767.347] (II) NOUVEAU(G0): 1024x768@75Hz
[ 1767.347] (II) NOUVEAU(G0): 1280x1024@75Hz
[ 1767.348] (II) NOUVEAU(G0): Manufacturer's mask: 0
[ 1767.348] (II) NOUVEAU(G0): Supported standard timings:
[ 1767.348] (II) NOUVEAU(G0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 1767.348] (II) NOUVEAU(G0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 1767.348] (II) NOUVEAU(G0): #2: hsize: 1600 vsize 900 refresh: 60 vid: 49321
[ 1767.348] (II) NOUVEAU(G0): #3: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 1767.348] (II) NOUVEAU(G0): Supported detailed timing:
[ 1767.348] (II) NOUVEAU(G0): clock: 148.5 MHz Image Size: 527 x 297 mm
[ 1767.348] (II) NOUVEAU(G0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 1767.348] (II) NOUVEAU(G0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 1767.348] (II) NOUVEAU(G0): Serial No: 36WJX3A92PPL
[ 1767.348] (II) NOUVEAU(G0): Monitor name: DELL P2414H
[ 1767.348] (II) NOUVEAU(G0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 1767.348] (II) NOUVEAU(G0): EDID (in hex):
[ 1767.348] (II) NOUVEAU(G0): 00ffffffffffff0010ac9aa04c505032
[ 1767.348] (II) NOUVEAU(G0): 29170104a5351e783aa0a5a656529d27
[ 1767.348] (II) NOUVEAU(G0): 0f5054a54b00714f8180a9c0d1c00101
[ 1767.348] (II) NOUVEAU(G0): 010101010101023a801871382d40582c
[ 1767.348] (II) NOUVEAU(G0): 45000f292100001e000000ff00333657
[ 1767.348] (II) NOUVEAU(G0): 4a583341393250504c0a000000fc0044
[ 1767.348] (II) NOUVEAU(G0): 454c4c205032343134480a20000000fd
[ 1767.348] (II) NOUVEAU(G0): 00384c1e5311000a202020202020004f
[ 1767.348] (II) NOUVEAU(G0): Printing probed modes for output DP-1-2
[ 1767.348] (II) NOUVEAU(G0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 1767.348] (--) NOUVEAU(G0): Virtual size is 1024x768 (pitch 0)
[ 1767.348] (**) NOUVEAU(G0): Mode "1920x1080": 173.0 MHz (scaled from 0.0 MHz), 67.2 kHz, 60.0 Hz
[ 1767.348] (II) NOUVEAU(G0): Modeline "1920x1080"x60.0 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync (67.2 kHz)
[ 1767.348] (==) NOUVEAU(G0): DPI set to (96, 96)
[ 1767.348] (II) Loading sub module "fb"
[ 1767.348] (II) LoadModule: "fb"
[ 1767.348] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 1767.348] (II) Module fb: vendor="X.Org Foundation"
[ 1767.348] compiled for 1.14.5, module version = 1.0.0
[ 1767.348] ABI class: X.Org ANSI C Emulation, version 0.4
[ 1767.348] (II) Loading sub module "exa"
[ 1767.348] (II) LoadModule: "exa"
[ 1767.348] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 1767.348] (II) Module exa: vendor="X.Org Foundation"
[ 1767.348] compiled for 1.14.5, module version = 2.6.0
[ 1767.348] ABI class: X.Org Video Driver, version 14.1
[ 1767.348] (II) Loading sub module "shadowfb"
[ 1767.348] (II) LoadModule: "shadowfb"
[ 1767.348] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[ 1767.348] (II) Module shadowfb: vendor="X.Org Foundation"
[ 1767.348] compiled for 1.14.5, module version = 1.0.0
[ 1767.348] ABI class: X.Org ANSI C Emulation, version 0.4
[ 1767.348] (--) Depth 24 pixmap format is 32 bpp
[ 1767.351] (II) NOUVEAU(G0): Opened GPU channel 0
[ 1767.359] (II) NOUVEAU(G0): [DRI2] Setup complete
[ 1767.359] (II) NOUVEAU(G0): [DRI2] DRI driver: nouveau
[ 1767.359] (II) NOUVEAU(G0): [DRI2] VDPAU driver: nouveau
[ 1767.360] (II) EXA(256): Driver allocated offscreen pixmaps
[ 1767.360] (II) EXA(256): Driver registered support for the following operations:
[ 1767.360] (II) Solid
[ 1767.360] (II) Copy
[ 1767.360] (II) Composite (RENDER acceleration)
[ 1767.360] (II) UploadToScreen
[ 1767.360] (II) DownloadFromScreen
[ 1767.360] (==) NOUVEAU(G0): Backing store disabled
[ 1767.360] (==) NOUVEAU(G0): Silken mouse enabled
[ 1767.360] (II) NOUVEAU(G0): [XvMC] Associated with Nouveau GeForce 8/9 Textured Video.
[ 1767.360] (II) NOUVEAU(G0): [XvMC] Extension initialized.
[ 1767.360] (==) NOUVEAU(G0): DPMS enabled
[ 1767.360] (II) NOUVEAU(G0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 1767.360] (WW) NOUVEAU(G0): Option "Monitor-DVI-I-1" is not used
[ 1767.360] (WW) NOUVEAU(G0): Option "Monitor-DP-1" is not used
[ 1767.362] (II) NOUVEAU(0): Opened GPU channel 0
[ 1767.366] (II) NOUVEAU(0): [DRI2] Setup complete
[ 1767.366] (II) NOUVEAU(0): [DRI2] DRI driver: nouveau
[ 1767.366] (II) NOUVEAU(0): [DRI2] VDPAU driver: nouveau
[ 1767.366] (II) EXA(0): Driver allocated offscreen pixmaps
[ 1767.366] (II) EXA(0): Driver registered support for the following operations:
[ 1767.366] (II) Solid
[ 1767.366] (II) Copy
[ 1767.366] (II) Composite (RENDER acceleration)
[ 1767.366] (II) UploadToScreen
[ 1767.366] (II) DownloadFromScreen
[ 1767.366] (==) NOUVEAU(0): Backing store disabled
[ 1767.366] (==) NOUVEAU(0): Silken mouse enabled
[ 1767.366] (II) NOUVEAU(0): [XvMC] Associated with Nouveau GeForce 8/9 Textured Video.
[ 1767.366] (II) NOUVEAU(0): [XvMC] Extension initialized.
[ 1767.366] (==) NOUVEAU(0): DPMS enabled
[ 1767.366] (II) NOUVEAU(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 1767.366] (--) RandR disabled
[ 1767.388] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 1767.388] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 1767.388] (II) AIGLX: enabled GLX_ARB_create_context
[ 1767.388] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 1767.388] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 1767.388] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 1767.388] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 1767.389] (II) AIGLX: Loaded and initialized nouveau
[ 1767.389] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 1767.390] (II) NOUVEAU(G0): NVEnterVT is called.
[ 1767.393] (II) NOUVEAU(0): NVEnterVT is called.
[ 1767.444] (II) NOUVEAU(0): Setting screen physical size to 508 x 285
[ 1767.444] resize called 1920 1080
[ 1767.479] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 1767.479] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 1767.479] (II) LoadModule: "evdev"
[ 1767.479] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 1767.479] (II) Module evdev: vendor="X.Org Foundation"
[ 1767.479] compiled for 1.14.3, module version = 2.8.2
[ 1767.479] Module class: X.Org XInput Driver
[ 1767.479] ABI class: X.Org XInput driver, version 19.1
[ 1767.479] (II) Using input driver 'evdev' for 'Power Button'
[ 1767.479] (**) Power Button: always reports core events
[ 1767.479] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 1767.479] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 1767.479] (--) evdev: Power Button: Found keys
[ 1767.479] (II) evdev: Power Button: Configuring as keyboard
[ 1767.479] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event2"
[ 1767.479] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 1767.479] (**) Option "xkb_rules" "evdev"
[ 1767.479] (**) Option "xkb_model" "pc104"
[ 1767.479] (**) Option "xkb_layout" "us"
[ 1767.499] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 1767.499] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 1767.499] (II) Using input driver 'evdev' for 'Power Button'
[ 1767.500] (**) Power Button: always reports core events
[ 1767.500] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 1767.500] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 1767.500] (--) evdev: Power Button: Found keys
[ 1767.500] (II) evdev: Power Button: Configuring as keyboard
[ 1767.500] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event1"
[ 1767.500] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 1767.500] (**) Option "xkb_rules" "evdev"
[ 1767.500] (**) Option "xkb_model" "pc104"
[ 1767.500] (**) Option "xkb_layout" "us"
[ 1767.500] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 1767.500] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event14)
[ 1767.500] (II) No input driver specified, ignoring this device.
[ 1767.500] (II) This device may have been added with another device file.
[ 1767.500] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event13)
[ 1767.500] (II) No input driver specified, ignoring this device.
[ 1767.500] (II) This device may have been added with another device file.
[ 1767.500] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event12)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event11)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event6)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event9)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA Intel PCH Line Out (/dev/input/event8)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event7)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.502] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event10)
[ 1767.502] (II) No input driver specified, ignoring this device.
[ 1767.502] (II) This device may have been added with another device file.
[ 1767.502] (II) config/udev: Adding input device DELL Dell USB Entry Keyboard (/dev/input/event4)
[ 1767.502] (**) DELL Dell USB Entry Keyboard: Applying InputClass "evdev keyboard catchall"
[ 1767.502] (II) Using input driver 'evdev' for 'DELL Dell USB Entry Keyboard'
[ 1767.502] (**) DELL Dell USB Entry Keyboard: always reports core events
[ 1767.502] (**) evdev: DELL Dell USB Entry Keyboard: Device: "/dev/input/event4"
[ 1767.502] (--) evdev: DELL Dell USB Entry Keyboard: Vendor 0x413c Product 0x2107
[ 1767.502] (--) evdev: DELL Dell USB Entry Keyboard: Found keys
[ 1767.502] (II) evdev: DELL Dell USB Entry Keyboard: Configuring as keyboard
[ 1767.502] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.5/4-1.5:1.0/input/input5/event4"
[ 1767.502] (II) XINPUT: Adding extended input device "DELL Dell USB Entry Keyboard" (type: KEYBOARD, id 8)
[ 1767.502] (**) Option "xkb_rules" "evdev"
[ 1767.502] (**) Option "xkb_model" "pc104"
[ 1767.502] (**) Option "xkb_layout" "us"
[ 1767.502] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event5)
[ 1767.502] (**) Logitech USB Optical Mouse: Applying InputClass "evdev pointer catchall"
[ 1767.502] (II) Using input driver 'evdev' for 'Logitech USB Optical Mouse'
[ 1767.502] (**) Logitech USB Optical Mouse: always reports core events
[ 1767.502] (**) evdev: Logitech USB Optical Mouse: Device: "/dev/input/event5"
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Vendor 0x46d Product 0xc077
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Found 12 mouse buttons
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Found scroll wheel(s)
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Found relative axes
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Found x and y relative axes
[ 1767.502] (II) evdev: Logitech USB Optical Mouse: Configuring as mouse
[ 1767.502] (II) evdev: Logitech USB Optical Mouse: Adding scrollwheel support
[ 1767.503] (**) evdev: Logitech USB Optical Mouse: YAxisMapping: buttons 4 and 5
[ 1767.503] (**) evdev: Logitech USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 1767.503] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.6/4-1.6:1.0/input/input6/event5"
[ 1767.503] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE, id 9)
[ 1767.503] (II) evdev: Logitech USB Optical Mouse: initialized for relative axes.
[ 1767.503] (**) Logitech USB Optical Mouse: (accel) keeping acceleration scheme 1
[ 1767.503] (**) Logitech USB Optical Mouse: (accel) acceleration profile 0
[ 1767.503] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000
[ 1767.503] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4
[ 1767.503] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)
[ 1767.503] (II) No input driver specified, ignoring this device.
[ 1767.503] (II) This device may have been added with another device file.
[ 1767.503] (II) config/udev: Adding drm device (/dev/dri/card1)
[ 1767.503] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event18)
[ 1767.503] (II) No input driver specified, ignoring this device.
[ 1767.503] (II) This device may have been added with another device file.
[ 1767.504] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event17)
[ 1767.504] (II) No input driver specified, ignoring this device.
[ 1767.504] (II) This device may have been added with another device file.
[ 1767.504] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event16)
[ 1767.504] (II) No input driver specified, ignoring this device.
[ 1767.504] (II) This device may have been added with another device file.
[ 1767.504] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event15)
[ 1767.504] (II) No input driver specified, ignoring this device.
[ 1767.504] (II) This device may have been added with another device file.
[ 1767.504] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 1767.504] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 1767.504] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 1767.504] (**) AT Translated Set 2 keyboard: always reports core events
[ 1767.504] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 1767.504] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 1767.504] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 1767.504] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 1767.504] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 1767.504] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)
[ 1767.504] (**) Option "xkb_rules" "evdev"
[ 1767.504] (**) Option "xkb_model" "pc104"
[ 1767.504] (**) Option "xkb_layout" "us"
[ 1767.505] (II) config/udev: Adding input device PS/2 Generic Mouse (/dev/input/event19)
[ 1767.505] (**) PS/2 Generic Mouse: Applying InputClass "evdev pointer catchall"
[ 1767.505] (II) Using input driver 'evdev' for 'PS/2 Generic Mouse'
[ 1767.505] (**) PS/2 Generic Mouse: always reports core events
[ 1767.505] (**) evdev: PS/2 Generic Mouse: Device: "/dev/input/event19"
[ 1767.505] (--) evdev: PS/2 Generic Mouse: Vendor 0x2 Product 0x1
[ 1767.505] (--) evdev: PS/2 Generic Mouse: Found 3 mouse buttons
[ 1767.505] (--) evdev: PS/2 Generic Mouse: Found relative axes
[ 1767.505] (--) evdev: PS/2 Generic Mouse: Found x and y relative axes
[ 1767.505] (II) evdev: PS/2 Generic Mouse: Configuring as mouse
[ 1767.505] (**) evdev: PS/2 Generic Mouse: YAxisMapping: buttons 4 and 5
[ 1767.505] (**) evdev: PS/2 Generic Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 1767.505] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input7/event19"
[ 1767.505] (II) XINPUT: Adding extended input device "PS/2 Generic Mouse" (type: MOUSE, id 11)
[ 1767.505] (II) evdev: PS/2 Generic Mouse: initialized for relative axes.
[ 1767.505] (**) PS/2 Generic Mouse: (accel) keeping acceleration scheme 1
[ 1767.505] (**) PS/2 Generic Mouse: (accel) acceleration profile 0
[ 1767.505] (**) PS/2 Generic Mouse: (accel) acceleration factor: 2.000
[ 1767.505] (**) PS/2 Generic Mouse: (accel) acceleration threshold: 4
[ 1767.505] (II) config/udev: Adding input device PS/2 Generic Mouse (/dev/input/mouse1)
[ 1767.505] (II) No input driver specified, ignoring this device.
[ 1767.505] (II) This device may have been added with another device file.
[ 1767.505] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[ 1767.505] (II) No input driver specified, ignoring this device.
[ 1767.505] (II) This device may have been added with another device file.
[ 1774.230] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 1774.230] (II) NOUVEAU(0): NVLeaveVT is called.
[ 1774.230] (II) NOUVEAU(G0): NVLeaveVT is called.
[ 1779.499] (II) evdev: PS/2 Generic Mouse: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: AT Translated Set 2 keyboard: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: Logitech USB Optical Mouse: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: DELL Dell USB Entry Keyboard: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: Power Button: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: Power Button: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) NOUVEAU(G0): NVLeaveVT is called.
[ 1780.500] Error dropping master: -22(Invalid argument)
[ 1780.501] (II) NOUVEAU(G0): Closed GPU channel 0
[ 1780.503] (II) NOUVEAU(0): Closed GPU channel 0
[ 1780.503] (EE) Server terminated successfully (0). Closing log file.
Thanks for any help!

I have a similar issue except with two ATI cards and four monitors.
I have a working xorg.conf that uses Xinerama and all 4 work but have been trying to get xrandr to work since xinerama is deprecated supposedly.
I would like to switch to xrandr but there is some kind of magic voodoo I have with my current xorg.conf that doesn't even work on an exact same machine and cards that I tried to setup for a co-worker.
lspci:
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610 [Radeon HD 2400 PRO/XT]
04:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610 [Radeon HD 2400 PRO/XT]
My xorg.conf:
Section "Device"
Identifier "ATI0"
Driver "radeon"
BusID "PCI:1:0:0"
Option "ZaphodHeads" "DVI-0"
Screen 0
EndSection
Section "Device"
Identifier "ATI1"
Driver "radeon"
BusID "PCI:1:0:0"
Option "ZaphodHeads" "DVI-1"
Screen 1
EndSection
Section "Device"
Identifier "ATI2"
Driver "radeon"
BusID "PCI:4:0:0"
Option "ZaphodHeads" "DVI-2"
Screen 0
EndSection
Section "Device"
Identifier "ATI3"
Driver "radeon"
BusID "PCI:4:0:0"
Option "ZaphodHeads" "DVI-3"
Screen 1
EndSection
Section "Monitor"
Identifier "DVI-0"
Option "Primary" "On"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
EndSection
Section "Monitor"
Identifier "DVI-1"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
EndSection
Section "Monitor"
Identifier "DVI-2"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
EndSection
Section "Monitor"
Identifier "DVI-3"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
EndSection
Section "Screen"
Identifier "Screen0"
Device "ATI0"
Monitor "DVI-0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "ATI1"
Monitor "DVI-1"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen2"
Device "ATI2"
Monitor "DVI-2"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen3"
Device "ATI3"
Monitor "DVI-3"
DefaultDepth 24
Subsection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Screen0" 0 0
Screen "Screen1" RightOf "Screen0"
Screen "Screen2" Above "Screen1"
Screen "Screen3" Above "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
Option "Xinerama" "1"
EndSection
My Xorg.0.log shows all the DVI connections when I don't use a xorg.conf file but only two are "connected"
I see DVI-0 and DVI-1 connected and in "xrandr -q" but in Xorg.0.log I see DVI-1-2 and DVI-1-3.
xrandr --listproviders show the two cards as well.
Tried "xrandr --setprovideroutputsource 1 0" and they show up in KDE but as clones and then X crashes eventually.
"xrandr --setprovideroutputsource 0 1" just plain crashes X

3 Monitors on E31 using integrated & discrete gpu?

I can't get the integrated graphics to show up in the device manager. I reset the BIOS to IGD and enabled multi-monitor support as per : http://download.lenovo.com/express/HT062445.html
I'm stuck...any ideas to get my 3rd monitor up and running?

I can't get the integrated graphics to show up in the device manager. I reset the BIOS to IGD and enabled multi-monitor support as per : http://download.lenovo.com/express/HT062445.html
I'm stuck...any ideas to get my 3rd monitor up and running?

How Do I use an Ati Radeon 4870 HD for 3 Monitors

I am new to the Apple world and community. I recently got a new job that requires me to use a Mac Pro. OS X version 10.6.8. 2.66 ghz dual xeon and 32 GB of ram. It has a ATI Radeon 4870 HD. I can run 2 monitors fine using the DVI and Mini DV port ( Using a convertor from apple. ). When I try to use the 2 other HDMI ports for my third monitor, Mac OS wont detect it. The wierd thing is some of the images from certain apps show on the 3rd Monitor.
Under graphics information it shows the Radeon 4870. Under PCIe information it shows the same card. On the back of my machine I have 2 HDMI slots and another lower down with Mini DV and DVI.
The Displays I am running are 3 HP LP2475w Monitors. Running in DVI mode with one converted to Mini DV. The 3rd non working is running in DVI to HDMI but it can be run Straight HDMI if need. Ive tried alot of configuration settings and I can't get the HDMI port to be detected by MAC OS. Ive plugged one in at a time and just the HDMI do not detect.
Please let me know what information is needed to help troubleshoot this better.

A 5770 is $249 or slightly less and in the same dept to me as replacing hard drives, adding some RAM in order to work and because my understanding is it was the first card to support 3 monitors.
The 5770 only requires 10.6.5+ - and the 4,1 had way too many issues with 10.5.7/10.5.8
The 4870 may or may not provide what you need for the software you run, even though 3 yr old machine but 4 yr old plus video card.
flashing:
http://boeglin.org/blog/index.php?entry=entry090918-031702
4870 vs GTX 285 that came out at that time also
http://www.geek.com/articles/games/macpro-whats-better-ati-radeon-4870-or-nvidia -gtx-285-20090720/
The default card was Nvidia GT120 and req'd no power cables and popular way to support more displays.
People were running DUAL 4870s to support 3rd monitor though back then:
http://forums.macrumors.com/showthread.php?t=665034&page=10

Dual monitor not working under Boot Camp on Mac Pro ATI HD 2600 XT

Recently got a brand new Mac Pro with ATI Radeon HD 2600 XT graphics card.
On the Mac side (Leopard), everything works perfectly: my second monitor (a plasma screen connected with HDMI to the second DVI of the ATI card via HDMI/DVI adapter) is fully recognized and it works as an extended desktop or in Mirroring mode.
Under Boot Camp (Windows XP Pro) however, NOTHING: the second monitor always appears in the display properties, but it is grayed out (inactive), and when I try to activate it, it switches back to being grayed out immediately and nothing gets displayed on it.
After reading all the posts I can find on the topic, I tried the following (in pretty much every possible combination - Thank god for WinClone that allows me to restore the Boot Camp basic install image without having to reinstall Windows from scratch every time):
a) Bootcamp 2.0 (installed by default by Bootcamp assistant)
b) Update to Bootcamp 2.1
1) Windows XP Pro SP2c vanilla install (from my Windows XP pro install disk)
2) Update to Windows XP SP3 (I tried with and without BC 2.1: both worked -> BC 2.1 didn't seem to be required for SP3 - maybe because this is a mac pro and not a MB or MBP)
i) ATI drivers installed by default by Boot Camp assistant (BC 2.0) or by BC 2.1
ii) Latest ATI drivers found on ATI web site specifically under Boot Camp / Mac Pro.
Note: Interestingly, the catalyst installer worked ok (provided .NET framework 2.0 is installed though), but it seems that the Radeon BootCamp/Mac Pro driver set itself from ATI's web site does NOT include a driver for the HD 2600 XT - so when I install this driver set, it tells me that no compatible hardware was found...
iii) Latest ATI drivers found under Windows XP (these did include one driver specifically for the Radeon HD 2600 XT)
NOTHING seems to work. I read posts (most of the from late last year) about ATI Catalyst utility showing a 3rd monitor at some point, but I never got any 3rd monitor showing in any of my many many trials with Catalyst. I have yet to get a single image appear on my plasma under Bootcamp Windows. I don't believe its the hardware because everything works great on the max OS X side.
I am actually considering switching to an NVidia 8800 GT just to get the dual screen to work under BootCamp/Windows XP because I really need it and I read everywhere that drivers for NVidia are far better than ATI ones.
Any advice? What should I try next before getting an 8800 ?
Is there a diagnostic utility that I can use to test my config including the GC?
Thanks!

Hi there aside from my laptop I have an iMac 20" with the same HD 2600 XT card. I recently installed the Catalyst 8.6 driver by using a driver mod from driverheaven, I use Vista 32. By installing it this way I got boosted performance and many issues with the bootcamp drivers were fixed. As you may already know the ATI drivers do not install on bootcamped macs usually but the mod tool fixes this. Its unofficial so do so at your own risk but try it out and see if you get the second monitor if not just rollback. Hope this helps and I didn't want to say too much about the 8.6 driver mod because it may not be allowed here but google will provide any answers.

T510 2nd External Monitor No Longer Working

Hey Guys,
Hopefully someone can help me out
Came into work with my T510 and inserted on to my Lenovo docking station type 4338. For over 2 years now I had it working with 2 external monitors and also the built in monitor display from the laptop. Now I can only get the built in monitor and monitor 2 (VGA on the docking station) to display.
It detects the 3rd monitor but when I try to extend to it everything goes black and I have to wait for it to time out or pop the laptop off the station and insert it back on.
If I try choosing just the 2 external monitors and close the laptop lid only monitor 2 displays and monitor 3 disconnects itself automatically.
Monitor 3 is connecting using a Display Port to VGA
I have tried 2 other monitors, same results. I have tried DVI and it makes no difference. I tried 2 different docking stations same results and I even reinstalled Windows 8.1 on the laptop hoping that would resolve the issue but it has not.
I know this can work because I had it working before. And the fact that I cant get 2 externals to display with the laptop screen closed is a telling sign something else is going on.
Thanks for all the help and suggestions hopefully to come!
Solved!
Go to Solution.

I was able to solve the issue.
For some reason my BIOS must have reverted back to just Intels intergrated GPU. I had to boot to BIOS and change the video setting to Optimus, I believe that is what it is called.
Once the change was made Windows 8.1 was able to install the drivers automatically, another reboot and all monitors now work.
Hope this helps someone in the future!

3rd Monitor

Similar Messages

Maybe you are looking for