3rd party Motion filter
Where do I install 3rd party filters in Motion?
They just show up in the filters list now. If the developer has published them to Apple's spec, you will have a folder with the name of the publisher. I have filter folders for BCC, idustrial design, CHV, etc.
bogiesan
Similar Messages
-
Does anybody know of a 3rd party motion menu retailer? The OEM menus are really good, but I would like to see more of what is out there. I have not yet mastered the creation of these menus, soooooo, in the meantime I am willing to pay for some really cool stuff . . . a DVD or CD or even a website . . .
Thanks,Good day all
yes you lad's do a good job here keep up the good work
on a quick note
have there been any improvements in CS4 for excluding a thumb button from navigation - without going to AFX
or do the old rules still apply
PHOTO ONLY DISPLAY after firstly setting the link of the button to the relevant imported image timeline to complete thumbnail capture then choose convert the button to an object this effectively resolves the issues of navigation and retains the auto button routing for all remaining buttons.
FOR VIDEO DISPLAY
after setting the menu to animate buttons and linking the button to the respective video or chapter point to complete capture
the method used to exclude this button from navigation could be for example
with button routing, you just have all four directions of the button go back to itself, ie if it's button 1 then set all four directions to button 1 and it shouldn't be accessible or do any thing if you accessed it.
Then set up all the other buttons to exclude that button and make sure button 1 isn't the default button.
Jon i think your packs are well priced for the content detail and attention included well worth the money
thing that interests me - is the video video change in the motion thumb buttons noticeable when switching to the transition videos ?
can i ask if anyone has a possible solution for this ?
We get asked a lot if it is possible to use the videoroom shown here
as a motion menu
as near to this a possible - by clicking on the respective video window the stream will play
Thanks Again -
Error msg is generated when attempt to crop a TIF that included a 3rd party filter not on
local machine. (Windows 7 Professional SP1)
1. File created in CS5 with third party filter applied to smart object (filter:Neat Image
published by ABSoft.)
2 Transfer to another computer that does not have the filter installed.
3. Open in Photoshop CS6.
4. Use crop tool to attempt to crop the photo.
5. Receive error message "Could not complete the command because of a program
error."
6. Crop completes and can be saved, but filter is disabled and cannot be enabled unless
moved back to original computer.
Expected result should be:
Allow filter to be enabled as CS5. Or message similar to message produced with
missing font.
Adobe Photoshop Version: 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00) x64
Operating System: Windows 7 64-bit
Version: 6.1 Service Pack 1
System architecture: Intel CPU Family:6, Model:10, Stepping:7 with MMX, SSE Integer,
SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, HyperThreading
Physical processor count: 4
Logical processor count: 8
Processor speed: 1995 MHz
Built-in memory: 6051 MB
Free memory: 2949 MB
Memory available to Photoshop: 5290 MB
Memory used by Photoshop: 60 %
Image tile size: 128K
Image cache levels: 4
OpenGL Drawing: Enabled.
OpenGL Drawing Mode: Advanced
OpenGL Allow Normal Mode: True.
OpenGL Allow Advanced Mode: True.
OpenGL Allow Old GPUs: Not Detected.
Video Card Vendor: NVIDIA Corporation
Video Card Renderer: GeForce GT 540M/PCI/SSE2
Display: 1
Display Bounds:= top: 0, left: 0, bottom: 768, right: 1366
Video Card Number: 1
Video Card: NVIDIA GeForce GT 540M
OpenCL Unavailable
Driver Version: 8.17.12.6744
Driver Date: 20110301000000.000000-000
Video Card Driver:
nvd3dumx.dll,nvwgf2umx.dll,nvwgf2umx.dll,nvd3dum,nvwgf2um,nvwgf2um
Video Mode:
Video Card Caption: NVIDIA GeForce GT 540M
Video Card Memory: 1024 MB
Video Rect Texture Size: 16384
Serial number: Tryout Version
Application folder: C:\Program Files\Adobe\Adobe Photoshop CS6 (64 Bit)\
Temporary file path: C:\Users\wayne\AppData\Local\Temp\
Photoshop scratch has async I/O enabled
Scratch volume(s):
Startup, 450.2G, 387.4G free
Required Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CS6 (64
Bit)\Required\
Primary Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CS6 (64 Bit)\Plug-ins\
Additional Plug-ins folder: not set
Installed components:
A3DLIBS.dll A3DLIB Dynamic Link Library 9.2.0.112
ACE.dll ACE 2012/01/18-15:07:40 66.492997 66.492997
adbeape.dll Adobe APE 2012/01/25-10:04:55 66.1025012 66.1025012
AdobeLinguistic.dll Adobe Linguisitc Library 6.0.0
AdobeOwl.dll Adobe Owl 2012/02/09-16:00:02 4.0.93 66.496052
AdobePDFL.dll PDFL 2011/12/12-16:12:37 66.419471 66.419471
AdobePIP.dll Adobe Product Improvement Program 6.0.0.1642
AdobeXMP.dll Adobe XMP Core 2012/02/06-14:56:27 66.145661 66.145661
AdobeXMPFiles.dll Adobe XMP Files 2012/02/06-14:56:27 66.145661 66.145661
AdobeXMPScript.dll Adobe XMP Script 2012/02/06-14:56:27 66.145661 66.145661
adobe_caps.dll Adobe CAPS 5,0,10,0
AGM.dll AGM 2012/01/18-15:07:40 66.492997 66.492997
ahclient.dll AdobeHelp Dynamic Link Library 1,7,0,56
aif_core.dll AIF 3.0 62.490293
aif_ocl.dll AIF 3.0 62.490293
aif_ogl.dll AIF 3.0 62.490293
amtlib.dll AMTLib (64 Bit) 6.0.0.75 (BuildVersion: 6.0; BuildDate: Mon Jan 16 2012
18:00:00) 1.000000
ARE.dll ARE 2012/01/18-15:07:40 66.492997 66.492997
AXE8SharedExpat.dll AXE8SharedExpat 2011/12/16-15:10:49 66.26830 66.26830
AXEDOMCore.dll AXEDOMCore 2011/12/16-15:10:49 66.26830 66.26830
Bib.dll BIB 2012/01/18-15:07:40 66.492997 66.492997
BIBUtils.dll BIBUtils 2012/01/18-15:07:40 66.492997 66.492997
boost_date_time.dll DVA Product 6.0.0
boost_signals.dll DVA Product 6.0.0
boost_system.dll DVA Product 6.0.0
boost_threads.dll DVA Product 6.0.0
cg.dll NVIDIA Cg Runtime 3.0.00007
cgGL.dll NVIDIA Cg Runtime 3.0.00007
CIT.dll Adobe CIT 2.0.5.19287 2.0.5.19287
CoolType.dll CoolType 2012/01/18-15:07:40 66.492997 66.492997
data_flow.dll AIF 3.0 62.490293
dvaaudiodevice.dll DVA Product 6.0.0
dvacore.dll DVA Product 6.0.0
dvamarshal.dll DVA Product 6.0.0
dvamediatypes.dll DVA Product 6.0.0
dvaplayer.dll DVA Product 6.0.0
dvatransport.dll DVA Product 6.0.0
dvaunittesting.dll DVA Product 6.0.0
dynamiclink.dll DVA Product 6.0.0
ExtendScript.dll ExtendScript 2011/12/14-15:08:46 66.490082 66.490082
FileInfo.dll Adobe XMP FileInfo 2012/01/17-15:11:19 66.145433 66.145433
filter_graph.dll AIF 3.0 62.490293
hydra_filters.dll AIF 3.0 62.490293
icucnv40.dll International Components for Unicode 2011/11/15-16:30:22 Build
gtlib_3.0.16615
icudt40.dll International Components for Unicode 2011/11/15-16:30:22 Build
gtlib_3.0.16615
image_compiler.dll AIF 3.0 62.490293
image_flow.dll AIF 3.0 62.490293
image_runtime.dll AIF 3.0 62.490293
JP2KLib.dll JP2KLib 2011/12/12-16:12:37 66.236923 66.236923
libifcoremd.dll Intel(r) Visual Fortran Compiler 10.0 (Update A)
libmmd.dll Intel(r) C Compiler, Intel(r) C++ Compiler, Intel(r) Fortran Compiler 10.0
LogSession.dll LogSession 2.1.2.1640
mediacoreif.dll DVA Product 6.0.0
MPS.dll MPS 2012/02/03-10:33:13 66.495174 66.495174
msvcm80.dll Microsoft® Visual Studio® 2005 8.00.50727.6195
msvcm90.dll Microsoft® Visual Studio® 2008 9.00.30729.1
msvcp100.dll Microsoft® Visual Studio® 2010 10.00.40219.1
msvcp80.dll Microsoft® Visual Studio® 2005 8.00.50727.6195
msvcp90.dll Microsoft® Visual Studio® 2008 9.00.30729.1
msvcr100.dll Microsoft® Visual Studio® 2010 10.00.40219.1
msvcr80.dll Microsoft® Visual Studio® 2005 8.00.50727.6195
msvcr90.dll Microsoft® Visual Studio® 2008 9.00.30729.1
pdfsettings.dll Adobe PDFSettings 1.04
Photoshop.dll Adobe Photoshop CS6 CS6
Plugin.dll Adobe Photoshop CS6 CS6
PlugPlug.dll Adobe(R) CSXS PlugPlug Standard Dll (64 bit) 3.0.0.383
PSArt.dll Adobe Photoshop CS6 CS6
PSViews.dll Adobe Photoshop CS6 CS6
SCCore.dll ScCore 2011/12/14-15:08:46 66.490082 66.490082
ScriptUIFlex.dll ScriptUIFlex 2011/12/14-15:08:46 66.490082 66.490082
tbb.dll Intel(R) Threading Building Blocks for Windows 3, 0, 2010, 0406
tbbmalloc.dll Intel(R) Threading Building Blocks for Windows 3, 0, 2010, 0406
TfFontMgr.dll FontMgr 9.3.0.113
TfKernel.dll Kernel 9.3.0.113
TFKGEOM.dll Kernel Geom 9.3.0.113
TFUGEOM.dll Adobe, UGeom© 9.3.0.113
updaternotifications.dll Adobe Updater Notifications Library 6.0.0.24 (BuildVersion: 1.0;
BuildDate: BUILDDATETIME) 6.0.0.24
WRServices.dll WRServices Friday January 27 2012 13:22:12 Build 0.17112
0.17112
wu3d.dll U3D Writer 9.3.0.113
Required plug-ins:
3D Studio 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Accented Edges 13.0
Adaptive Wide Angle 13.0
ADM 3.11x01
Angled Strokes 13.0
Average 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Bas Relief 13.0
BMP 13.0
Camera Raw 7.0
Chalk & Charcoal 13.0
Charcoal 13.0
Chrome 13.0
Cineon 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Clouds 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Collada 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Color Halftone 13.0
Colored Pencil 13.0
CompuServe GIF 13.0
Conté Crayon 13.0
Craquelure 13.0
Crop and Straighten Photos 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Crop and Straighten Photos Filter 13.0
Crosshatch 13.0
Crystallize 13.0
Cutout 13.0
Dark Strokes 13.0
De-Interlace 13.0
Dicom 13.0
Difference Clouds 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Diffuse Glow 13.0
Displace 13.0
Dry Brush 13.0
Eazel Acquire 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Embed Watermark 4.0
Entropy 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Extrude 13.0
FastCore Routines 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Fibers 13.0
Film Grain 13.0
Filter Gallery 13.0
Flash 3D 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Fresco 13.0
Glass 13.0
Glowing Edges 13.0
Google Earth 4 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Grain 13.0
Graphic Pen 13.0
Halftone Pattern 13.0
HDRMergeUI 13.0
IFF Format 13.0
Ink Outlines 13.0
JPEG 2000 13.0
Kurtosis 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Lens Blur 13.0
Lens Correction 13.0
Lens Flare 13.0
Liquify 13.0
Matlab Operation 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Maximum 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Mean 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Measurement Core 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Median 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Mezzotint 13.0
Minimum 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
MMXCore Routines 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Mosaic Tiles 13.0
Multiprocessor Support 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Neon Glow 13.0
Note Paper 13.0
NTSC Colors 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Ocean Ripple 13.0
Oil Paint 13.0
OpenEXR 13.0
Paint Daubs 13.0
Palette Knife 13.0
Patchwork 13.0
Paths to Illustrator 13.0
PCX 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Photocopy 13.0
Photoshop 3D Engine 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Picture Package Filter 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Pinch 13.0
Pixar 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Plaster 13.0
Plastic Wrap 13.0
PNG 13.0
Pointillize 13.0
Polar Coordinates 13.0
Portable Bit Map 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Poster Edges 13.0
Radial Blur 13.0
Radiance 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Range 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Read Watermark 4.0
Reticulation 13.0
Ripple 13.0
Rough Pastels 13.0
Save for Web 13.0
ScriptingSupport 13.0
Shear 13.0
Skewness 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Smart Blur 13.0
Smudge Stick 13.0
Solarize 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Spatter 13.0
Spherize 13.0
Sponge 13.0
Sprayed Strokes 13.0
Stained Glass 13.0
Stamp 13.0
Standard Deviation 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Sumi-e 13.0
Summation 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Targa 13.0
Texturizer 13.0
Tiles 13.0
Torn Edges 13.0
Twirl 13.0
U3D 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Underpainting 13.0
Vanishing Point 13.0
Variance 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Variations 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Water Paper 13.0
Watercolor 13.0
Wave 13.0
Wavefront|OBJ 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
WIA Support 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
Wind 13.0
Wireless Bitmap 13.0 (13.0 20120305.m.415 2012/03/05:21:00:00)
ZigZag 13.0
Optional and third party plug-ins: NONE
Plug-ins that failed to load: NONE
Flash:
Mini Bridge
Kuler
Installed TWAIN devices: NONESee if you can troubleshoot Safari extensions and third party plugins before Safari crashes.
From the Safari menu bar click Safari > Preferences then select the Extensions tab. Turn that OFF, quit and relaunch Safari to test. If that helped, turn one extension on then quit and relaunch Safari to test until you find the incompatible extension then click uninstall.
If it's not an extensions issue, try troubleshooting third party plug-ins.
Back to Safari > Preferences. This time select the Security tab. Deselect: Allow plug-ins. Quit and relaunch Safari to test.
If that made a difference, instructions for troubleshooting plugins here. -
3rd party filter missing after upgrade to Photoshop CC 2014
Upgraded my Photoshop CC to 2014.... all my presets seems to have imported fine, but none of my 3rd party filters, like Nik and Topaz are showing up in the filter menu.
What happened to them??You'll need to reinstall them into Photoshop CC (2014). It's a completely separate application on your system, in a different set of folders.
-Noel -
CS4 plug-ins, 3rd party plug-ins and filter problems
1- What happened to all the filters available in CS3? They were a good thing. Why does Adobe kill off what's already working well and looking good? For instance, where's the Distort>Diffuse???
2- Same thing with PS plug-ins and third party plug-ins. They're all gone, now that I've "upgraded." (A term I use with disgust.) I paid too much money for all the aggravation I've been experiencing with these three issues.
But I digress: I dragged plug-ins to the folder, but they still don't show up.
Thank you.......
iMac 23" 2.16 GHz, Intel Core 2 Duo 3 GB RAM OS 10.5.5 ACR5.2
PS: Why does Adobe take away what finally works smoothly? Why offer a feature, and then take it back 18 months later with the next version? I'll sleep better at night if I can just understand how it helps the users to have the useful deleted.First of all, make sure you have not moved the application icon or the application folder from the default install location, and that you have not created subfolders there in a misguided attempt to "organize" things.
Secondly, please tell us what you upgraded from. If you had been running some 3rd party plugins that are not written for Universal Binary, they may not run in a newer OS or a newer machine.
Third, please see the documentation or Adobe Photoshop's Principal Program Manager John Nack's blog for the stuff that
was taken out in CS4:
http://blogs.adobe.com/jnack/2008/10/where_did_extra.html
Filter > Distort > Diffuse Glow is right there where it's always been. If you don't see it, you're either in 16 bits or have a bad install. -
How do I install 3rd party filters in Motion 3? Also.. How can I remove folders in the 3rd party filters tab within Motion. Where is the 3rd Party Filters folder in the finder? thanks
I have all that, but I don't understand how to do it.. In the original Motion, there was a 3rd party location selection in the prefs.. The manual, on page 139, says Click Choose (next to the search path). I cannot find that... I can only find the CHOOSE for the Library Path.
On page 139 it states that the FX have to be Universal, but on page 963, it says it 3rd party filters only work on Power PCs...
I've also added a few "Untitled Folder"s to the 3rd Party Filters tab within Motion. How can I remove them? Do they physically sit on the hard drive somewhere?
I'm lost. Can I do this....? thanks -
3rd party filter callup in panel
Can someone tell me how to call up a 3rd party PSCS5 plug-
in filter in a panel in configurator 2 please?
I would like to build a panle with my most used filters such as Nik, onOne,Topaz etc
JImmy1. You may install "ScriptingSupport.8li", and invoke your plug-in. Then go to desktop, check file "ScriptingListenerJS.log".
If it can record a piece of script, then you can drag a script button, and paste script into "script" attribute.
2. If it can't record to script, you can try to new an action, and click the menu item of your plug-in. And then drag an "Action" button, set the action name and "Action Set".
You can find post about how to package an action with Configuartor panel in this forum. -
Text transitions, 3rd party plug-ins, etc.
This seems so simple, but I cannot find it anywhere. I am using motion to create moving pictures and text. I want the text to blur in and out slowly (all of the letters at the same time). I found the text sequence blur but the letters will only be in sequence like left to right or random, correct? I have looked for 3rd party plug-ins but can't find anything as simple as a transitional blur for text. Any suggestions?
Thank you!!You can modify any of the text sequence behaviors in any way imaginable. Try increasing the Spread value to spread out the animation. Or, just add a blur filter to the text and keyframe the blur amount to change over time.
-
Is there a 3rd Party Solution for Adobe's lack of recover for unsaved work?
Time and time again I am baffled by Adobe's inability or refusal to make the user experience consistent across it's entire Creative Suite.
I am repeatedly shocked by the punitive error messages I receive in Photoshop. It's as though you don't really care what the user wants, I mean what are we going to do, use MS Paint? So you are at liberty to provide such classic errors as "Unable to complete your request because of a program error" instead of "wait, did you mean apply that filter to the only visible layer that you had selected just seconds before and never requested that the layer be de-selected?" I could go on and on with the crazy and convoluted exceptions to logic in Photoshop, but I would rather just understand why, when you know that a problem exists and affects 90% of your users at some point, why wouldn't you try to build in some form of recovery when your program crashes
Why should I be punished for relying on your program not to crash when I am working on something? I have repeatedly been advised that the best solution is to save often. Sometimes that's not an option and why should it be my responsibility to compensate for your buggy program?
After 20 years of development, you can't figure out how to recover someone's work if they haven't been able to save for some reason and Phtooshop crashes? I have been using Photoshop since Version 3 (for sure, but more likely version 2) and back then you could rename your temp files and recover the work you hadn't saved. I understand that the mechanism by which fast previews (comps) of your work are displayed but not applied (like Live Image), but why isn't it possible to store a simple text file that could retrace my steps if your program crashes?
This is a real problem if you are processing a filter that takes 30 minutes and Photoshop waits until 29 minutes and 59 seconds to announce that it stopped working. Granted you can see your document in the background, but you can't save it? You can't commit whatever is in RAM for the undo states to disk? You can't have your program quickly save a new text file with the list of commands applied between saves? You can't do anything? After 20 years?
Microsoft includes recovery in Word, Excel, etc. Even SOME Adobe programs do it: InDesign...AfterEffects. Why doesn't your flagship program do it?
It's frustrating beyond belief and it baffles me that Adobe is celebrating the 20th anniversary of Photoshop and yet this basic, basic customer need is still not effectively addressed and furthermore, any question about it is answered with indignant indifference:
it doesn't work and we don't care what you want,
think you'd be happier with our competition....
oh wait, we don't really have any competition...
maybe you should save more often...
Is there a 3rd party solution that will allow me to recover my work in Photoshop when it crashes between saves? Or am I just stuck having to cope with rebuilding my work because Adobe refuses to provide a solution.
(let the backlash begin as I try to simulate my lens blur using MS Paint....not gonna happen)
JaseGo to google and search for keyboard recording software. That will record all of your keystrokes.
CS4 running under windows 7 appearently has some problems. While it would be nice if Adobe went back and rewrote there software for an operating system that was in early development when CS4 was released, it is not likely to happen.
Excuse me, they did it is called Adobe Photoshop CS5 and is due to be release soon.
If, If you would stop ranting for a minute, and quit feeling like you are being slammed, and possibly listen for a minute.
I am currently running Windows Vista Home Premium "not my choice" on a Toshiba A215-S4747 with 3gb ram. When I bought this laptop the Toshiba Rep was at the Best Buy and I spoke with him about this very computer. I did not want to run Windows Vista, period, I had heard to many bad reports about it. The Toshiba Rep told me that was not a problem and this computer would run Windows XP Professional just fine.
So I bought this computer and 2gb of ram as it only came with 512mb. I went home happly and proceeded to install Windows XP Pro and the new memory. Guess what?
this computer will in fact run Windows XP Pro just fine as long as you take into consideration that there are almost no hardware drivers for the periferals that make up this computer.
So I reinstall Windows Vista and for the next year I am tied into fits because of system crashes. Finally I am at the point that I am going to take this computer to the Toshiba Office in Torrance California and personally give it back to them "I was going to throw it through the front office window.".
Just before I ran across memtest and I downloaded it and tested my memory. You got it I had a defective ram chip.
Best Buy replaced the chip no problem. that was in November of 2008. I do horrible things to this computer, I really can drive it. It has not crashed once since I found and fixed the problem.
No one is suggesting that you are an idiot! or inexperienced. but no matter what you do remember 2 very simple rules.
If you run into a problem 1. "Go Back To Basics" and 2. "KISS ie: keep it simple stupid" if you do this and I am speaking from my own experience you will find like and work a lot simpler and more pleasent. -
Using 3rd party tags in JSF application
I have a 3rd party tag library used previously in a Struts application to check if an user is authenticated / has logged in. The tag looks like this: <authn:authenticate userVarName="user" scope="session" errorPage="error.jsp" successPage="/faces/Page1.jsp"></authn:authenticate>. One unusual thing about the tag is that the uri for it references a jar file that includes the tld.
I can build the app okay but deployment fails with the following error:
Deploying application in domain failed; Error loading deployment descriptors for authapp Line 91 Column 10 -- cvc-complex-type.2.4.a: Invalid content was found starting with element 'taglib'. One of '{"http://java.sun.com/xml/ns/j2ee":description, "http://java.sun.com/xml/ns/j2ee":display-name, "http://java.sun.com/xml/ns/j2ee":icon, "http://java.sun.com/xml/ns/j2ee":distributable, "http://java.sun.com/xml/ns/j2ee":context-param, "http://java.sun.com/xml/ns/j2ee":filter, "http://java.sun.com/xml/ns/j2ee":filter-mapping, "http://java.sun.com/xml/ns/j2ee":listener, "http://java.sun.com/xml/ns/j2ee":servlet, "http://java.sun.com/xml/ns/j2ee":servlet-mapping, "http://java.sun.com/xml/ns/j2ee":session-config, "http://java.sun.com/xml/ns/j2ee":mime-mapping, "http://java.sun.com/xml/ns/j2ee":welcome-file-list, "http://java.sun.com/xml/ns/j2ee":error-page, "http://java.sun.com/xml/ns/j2ee":jsp-config, "http://java.sun.com/xml/ns/j2ee":security-constraint, "http://java.sun.com/xml/ns/j2ee":login-config, "http://java.sun.com/xml/ns/j2ee":security-role, "http://java.sun.com/xml/ns/j2ee":env-entry, "http://java.sun.com/xml/ns/j2ee":ejb-ref, "http://java.sun.com/xml/ns/j2ee":ejb-local-ref, "http://java.sun.com/xml/ns/j2ee":service-ref, "http://java.sun.com/xml/ns/j2ee":resource-ref, "http://java.sun.com/xml/ns/j2ee":resource-env-ref, "http://java.sun.com/xml/ns/j2ee":message-destination-ref, "http://java.sun.com/xml/ns/j2ee":message-destination, "http://java.sun.com/xml/ns/j2ee":locale-encoding-mapping-list}' is expected.
; requested operation cannot be completed
Exception=Deployment failed.
The tag's tld is <tlib-version>1.1</tlib-version> <jsp-version>1.2</jsp-version>. I'm not sure if this is the problem or if 3rd party tags don't necessarily work within JSF (am using Creator) without modification. Does anyone have any advise on this? Should 3rd party tags work? If not, how do they need to be modified or turned into a component to work? This tag doesn't display anything - it checks if users have logged in and redirects them to another site to login if they did not log in.
Message was edited by:
sstgermain
Message was edited by:
sstgermainThanks for your reply! I do have the jar file, which includes the .tld, in my WEB-INF/lib
On Page1.jsp I tried using <%@ taglib uri="/WEB-INF/lib/myLibrary.jar" prefix="myTag" %> but got errors so I moved it to <jsp:root version="1.2" xmlns:myTag="/WEB-INF/lib/myLibrary.jar"...Should the <%@taglib uri = work? When I tried to use <%@taglib version I got errors saying strict xml enforced.
I am using the format prefix:tag format <myTag:checkaccess userVarName="user"
scope="session"
errorPage="error.jsp" ></myTag:checkaccess>
Do I need to somehow convert this tag into a component?
I think the jar is fine since I'm using it in a number of other applications.
Should the tag work? Do non-JSF tags have to be turned into components? -
I have a 3rd party tag library, used previously in Struts apps, that I would like to use in a JSF application. The tag checks if a user has logged in to the app and redirects to a login site if not. It doesn't display anything to the screen. Should a 3rd party tag that worked with JSP/Struts work with JSP without modification???? If not, how do I need to modifiy it? Please let me know!
I imported the necessary libaries for the tag using <jsp:directive.page import="myFiles.*"/>
I added the tags uri (which happens to be a jar file in /web-inf/ to the <jsp:root version="1.2" xmlns:authn="/WEBINF/lib/myLibrary.jar"
The tag itself which I put between <jsp:root tags on Page1.jsp looks like this: <myTag:checkaccess userVarName="user"
scope="session"
errorPage="error.jsp"
Info from the tld: <tlib-version>1.1</tlib-version>
<jsp-version>1.2</jsp-version>
I have the taglib entry in the web.xml
I can build the app but when I try to deploy it I get the following error:
Deploying application in domain failed; Error loading deployment descriptors for devpin Line 91 Column 13 -- cvc-complex-type.2.4.a: Invalid content was found starting with element 'taglib'. One of '{"http://java.sun.com/xml/ns/j2ee":description, "http://java.sun.com/xml/ns/j2ee":display-name, "http://java.sun.com/xml/ns/j2ee":icon, "http://java.sun.com/xml/ns/j2ee":distributable, "http://java.sun.com/xml/ns/j2ee":context-param, "http://java.sun.com/xml/ns/j2ee":filter, "http://java.sun.com/xml/ns/j2ee":filter-mapping, "http://java.sun.com/xml/ns/j2ee":listener, "http://java.sun.com/xml/ns/j2ee":servlet, "http://java.sun.com/xml/ns/j2ee":servlet-mapping, "http://java.sun.com/xml/ns/j2ee":session-config, "http://java.sun.com/xml/ns/j2ee":mime-mapping, "http://java.sun.com/xml/ns/j2ee":welcome-file-list, "http://java.sun.com/xml/ns/j2ee":error-page, "http://java.sun.com/xml/ns/j2ee":jsp-config, "http://java.sun.com/xml/ns/j2ee":security-constraint, "http://java.sun.com/xml/ns/j2ee":login-config, "http://java.sun.com/xml/ns/j2ee":security-role, "http://java.sun.com/xml/ns/j2ee":env-entry, "http://java.sun.com/xml/ns/j2ee":ejb-ref, "http://java.sun.com/xml/ns/j2ee":ejb-local-ref, "http://java.sun.com/xml/ns/j2ee":service-ref, "http://java.sun.com/xml/ns/j2ee":resource-ref, "http://java.sun.com/xml/ns/j2ee":resource-env-ref, "http://java.sun.com/xml/ns/j2ee":message-destination-ref, "http://java.sun.com/xml/ns/j2ee":message-destination, "http://java.sun.com/xml/ns/j2ee":locale-encoding-mapping-list}' is expected.
; requested operation cannot be completed
Exception=Deployment failed.
Deployment failed.
at org.netbeans.modules.j2ee.deployment.devmodules.api.Deployment.deploy(Deployment.java:210)
at org.netbeans.modules.j2ee.ant.Deploy.execute(Deploy.java:75)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
at org.apache.tools.ant.Task.perform(Task.java:364)
at org.apache.tools.ant.Target.execute(Target.java:341)
at org.apache.tools.ant.Target.performTasks(Target.java:369)
at org.apache.tools.ant.Project.executeTarget(Project.java:1214)
at org.apache.tools.ant.Project.executeTargets(Project.java:1062)
at org.apache.tools.ant.module.bridge.impl.BridgeImpl.run(BridgeImpl.java:234)
at org.apache.tools.ant.module.run.TargetExecutor.run(TargetExecutor.java:242)
at org.netbeans.core.execution.RunClassThread.run(RunClassThread.java:125)
C:\Documents and Settings\sstgerma\My Documents\Creator\Projects\devpin\nbproject\build-impl.xml:607: Deployment failed.
BUILD FAILED (total time: 0 seconds)
Message was edited by:
sstgermainThanks for your reply! I do have the jar file, which includes the .tld, in my WEB-INF/lib
On Page1.jsp I tried using <%@ taglib uri="/WEB-INF/lib/myLibrary.jar" prefix="myTag" %> but got errors so I moved it to <jsp:root version="1.2" xmlns:myTag="/WEB-INF/lib/myLibrary.jar"...Should the <%@taglib uri = work? When I tried to use <%@taglib version I got errors saying strict xml enforced.
I am using the format prefix:tag format <myTag:checkaccess userVarName="user"
scope="session"
errorPage="error.jsp" ></myTag:checkaccess>
Do I need to somehow convert this tag into a component?
I think the jar is fine since I'm using it in a number of other applications.
Should the tag work? Do non-JSF tags have to be turned into components? -
No SDO Communication Using CAN over EtherCAT (CoE) with 3rd Party Slave
Dear all
We are trying to establish an EtherCAT communication between a cRIO 9024 as EtherCAT master with a 3rd party frequency comverter (bmaxx 4432) as EtherCAT slave. CanOPEN over EtherCAT is industry standard.
The slave device has a CAN in Automation (CiA) configuration 402, i.e. motion and drives. Thus it has a well configured address range, input/output parameters and the like. The frequency converter remains in INIT mode and waits for a PDO definition, sent via an SDO communication.
In LabView, adding an EtherCAT master in the cRIO system works fine. Adding targets and devices on the configured EtherCAT master also works fine after we imported an XML description of our third party EtherCAT slave. LabView detects the slave type and the version correctly. Thus, there must already be a rudimentary EtherCAT communication working between LabView and our 3rd party slave.
The problem is that we cannot establish a first SDO communication.
Every description I found was about using CANopen on a CAN bus hardware (e.g. NI 9861) plugged into the cRIO. Descriptions concerning EtherCAT are usually concerning an NI cRIO 9144 extension as slave, which is not what we have.
The NI CANopen library seems to definitely require the NI 9861.
Is this correct?
1)
Either it should be possible to define a kind of virtual CAN port based on the EtherCAT port, on which we can write to and read from with the NI CANopen library. This would be the preferred solution so we can use the CANopen VIs.
Is there a way to do this?
2)
Otherwise, there should be a possibility to establish a more basic SDO/PDO communication directly based on the EtherCAT interface.
Are there any NMT/SDO/PDO VIs available to do the programming?
Is there a manual document which would describe how to start the first communication setup via EtherCAT (CoE)?
My sincere thanks for any advice you can give.
Many cheers
MarkusDear all,
I'm trying to establish a connection between a cRIO9068 and a BM 3300 via CoE.
I already had a hard time establishing a normal EtherCAT-connection.
Finally I could set the Scan engine to active, and I was able to get from "ini" and "pre operational" into "Safe operational" and "operational".
As I can see, you had similar problems as I do.
When I add my cRIO to my project (with the EterCAT-master) I can look for the slave device, and add it to my project.
Within this slave device, I can add two mods, as seen in the attachment.
These slots should include all the parameters, the drive provides, but actually I only end up with some "position mode" -parameters, I think those are the SDO's.
If I add these to a VI, the cRIO scan engine switches to configuration mode, but can't switch back to active mode.
Actually, the Baumüller slave device should be able to provide multiple parameters for read and write.
I can see them, wehn I go to "online device state" in the rightklick menu of the slave device (Parameter.png), but there's no way I can actually use them.
I can't add these "slots" on every computer.
On some computers it's possible, on some it isn't.
Thanks for any advice, you can give.
Yours sincerely
Karl
Attachments:
slot 1.PNG 6 KB
slot 2.PNG 9 KB
Parameter.PNG 46 KB -
"3rd Party Plug-Ins" Not Showing Up In Preference Pane...
I'm trying to install a couple of 3rd-Party Plug-Ins... Apparently the procedure for this is to go to Preferences, and in the "General" pane, there should be a heading that says "3rd Party Plug-Ins" along with buttons "Choose..." and "Clear" and a path.
On my General Preferences Pane, there is no such section... It goes right from "Content Library & Templates" to "Media," with no "3rd Party Plug-Ins" listed anywhere in the pane.
Using Motion 3.0.2.... Did something change and they didn't change the manual to match? Or is there some setting elsewhere that's making that option disappear?
Thanks!!!
NickHowdy,
The "3rd party plug-ins" section in the Library and preferences really refers to AE plug-ins. Third-party FxPlug plug-ins (like dvMatte or Boris Continuum) show up mixed in with the regular filters and generators.
That "3rd party plug-ins" path setting in the preferences doesn't appear on Intel-based Macs, as they're no longer supported. If you have a PowerPC system, they'll show up (and so will the setting). -
Reframing my Question for RESTful 3rd Party WebService
My last posted question did not produce any feedback for what I was looking for, so I'm trying this again.
I have a Driver entity, and an gpsVehicleData entity. Drivers can have one gpsVehicleData (relationship)
In a grid screen I use; for THE most basic understanding I can get, I have one field I need updated from my 3rd party webservice. We'll call it gpsVehicleData.MotionStatus, and I need to use Driver.DriverID in the service to find his MotionStatus.
This is the example connection snippet I was given by the vendor.
Dim responseData As String = ""
Dim uri As String = "http://ws.samplegps.com/DriverWebService.svc/drivers/"
Dim request As System.Net.HttpWebRequest = Net.HttpWebRequest.Create(uri)
request.Method = "GET"
Dim companyLoginId As String = "12345"
Dim username As String = "John"
Dim password As String = "Doe4321"
Dim auth As String = companyLoginId + "|" + username + ":" + password
Dim authHeader As String = Convert.ToBase64String(System.Text.Encoding.UTF8.GetBytes(auth))
request.Headers("Authorization") = authHeader
Try
Dim httpWebResponse As System.Net.HttpWebResponse = request.GetResponse()
If httpWebResponse.StatusCode = Net.HttpStatusCode.OK Then
Dim responseStream As IO.StreamReader = New IO.StreamReader(httpWebResponse.GetResponseStream())
responseData = responseStream.ReadToEnd()
Console.WriteLine(responseData)
Console.ReadKey()
End If
Catch ex As Exception
responseData = "An error occured: " & ex.Message
Console.WriteLine(responseData)
Console.ReadKey()
Great. So this works when I run in it's own solution, and it pops up a console window and shows all data for each of my drivers. My problem is, I cannot find an example I can follow to update the Motion property in EACH ROW (each driver of my Screen with
this snippet.
(A button function seems appropriate instead of Validate method, but honestly as long as it works I don't care.
This is the closest I have found but I'm not using Soap.
LightSwitch - Consuming Web Services
This is too, but much different than the first example!
Calling Web Services to Validate Data in Visual Studio LightSwitch
One example has something and not the other, and the other example has this but not that. Very frustrating for a new person!
I do not need to dive into RIA right now which has been suggested before.
I know I am not very knowledgeable in VB, but I need to use something applicable to my environment I can make more sense of. Thanks in advanceThis is the closest I have found but I'm not using Soap.
LightSwitch - Consuming Web Services
From your description, you can consider using method above, as I know, this way is available/convenient for your situation. -
3rd party distributed SW load balancing with In-Memory Replication
Hi,
Could someone please comment on the feasibility of the following setup?
I've started testing replication with a software load balancing product. This
product lets all nodes receive all packets and uses a kernel-level filter
to let only one node at the time receive it. Since there's minimum 1 heartbeat
between the nodes, there are several NICs in each node.
At the moment it seems like it doesn't work: - I use the SessionServlet - with
a 2-node cluster I first have the 2 nodes up and I access it with a single client:
.the LB is configured to be sticky wrt. source IP address, so the same node gets
all the traffic - when I stop the node receiving the traffic the other node takes
over (I changed the colours of SessionServlet) . however, the counter restarts
at zero
From what I read of the in-memory replication documentation I thought that it
might work also with a distributed software load balancing cluster. Any comments
on the feasability of this?
Is there a way to debug replication (in WLS6SP1)? I don't see any replication
messages in the logs, so I'm not even sure that it works at all. - I do get a
message about "Clustering Services startting" when I start the examples server
on each node - is there anything tto look for in the console to make sure that
things are working? - the evaluation license for WLS6SP1 on NT seems to support
In-Memory Replication and Cluster. However, I've also seen a Cluster-II somewhere:
is that needed?
Thanks for your attention!
Regards, Frank Olsen
We are considering Resonate as one of the software load balancer. We haven't certified
them yet. I have no idea how long its going to take.
As a base rule if the SWLB can do the load balancing and maintain stickyness that is fine
with us as long as it doesn't modify the cookie or the URL if URL rewriting is enabled.
Having said that if you run into problems we won't be able to support you since it is not
certified.
-- Prasad
Frank Olsen wrote:
> Prasad Peddada <[email protected]> wrote:
> >Frank Olsen wrote:
> >
> >> Hi,
> >>
> > We don't support any 3rd party software load balancers.
>
> Does that mean that there are technical reasones why it won't work, or just that
> you haven't tested it?
>
> > As >I said before I am thinking your configuration is >incorrect if n-memory
> replication is not working. I would >strongly suggest you look at webapp deployment
> descriptor and >then the config.xml file.
>
> OK.
>
> >Also doing sticky based on source ip address is not good. You >should do it based
> on passive cookie persistence or active >cookie persistence (with cookie insert,
> a new one).
> >
>
> I agree that various source-based sticky options (IP, port; network) are not the
> best solution. In our current implementation we can't do this because the SW load
> balancer is based on filtering IP packets on the driver level.
>
> Currently I'm more interested in understanding whether it can our SW load balancer
> can work with your replication at all?
>
> What makes me think that it could work is that in WLS6.0 a session failed over
> to any cluster node can recover the replicated session.
>
> Can there be a problem with the cookies?
> - are the P/S for replication put in the cookie by the node itself or by the proxy/HW
> load balancer?
>
> >
> >The options are -Dweblogic.debug.DebugReplication=true and
> >-Dweblogic.debug.DebugReplicationDetails=true
> >
>
> Great, thanks!
>
> Regards,
> Frank Olsen
Maybe you are looking for
-
My contacts are merging with wife, son and daughter. How do we create separate ID's but still maintain same iTunes account?
-
How do I export every calendar in my iCal to an ics file?
I am trying to export all my calendars from iCal to ane ics file. It is exporting calendar events that i have been invited to by others but is not exporting any calendar events that I have created myself. Please help. I have gone in and done the
-
Creation of Inbound Idoc for the Outbound Idoc in same client
Hi, My requirement: Whenver an PO is created an Outbound IDOC is generated in system ABC with client 100.I want to pass this IDOC data to create an Inbound Idoc for Sales Order(SO) in the same client. It would be helpful if anyone can answer on how t
-
Create a fulfilled order in EBS R12
We are using another system to do the order fulfillment. But we are using Oracle Inventory functionality to maintain a virtual inventory. So when we fulfill an order we need to create that order in Oracle OM, so that we can increment/decrement the Or
-
What happened to my "Photoshop JPEG file" format?
On my previous two computers -- a G5 running 10.4, a MacBookPro on 10.5, both using Photoshop CS3 -- I used to have two kinds of JPEG files. One was listed in the Finder as "JPEG file," and that opened in Preview; the other was "Photoshop JPEG file,"