3rd Party Software for AirPort Extreme Base Station?

Is there any 3rd party software which would allow a little more functionality and control of the device? Like the ability to see wired clients on the network, at the most basic? I have one of the new tower Extremes and Apple seems to have removed the option for downloading AirPort Utility 5.6 which I understand had much more functionality. Can any of you suggest some other software that offers more than the current iteration of AirPort Utility does? Thanks

Unfortunately no.
Tell Apple: http://www.apple.com/feedback/airportextreme.html

Similar Messages

  • DNS settings for Airport Extreme Base Station

    This month's MacWorld suggests that changing the DNS setting of the wireless device might increase the speed of the connection. What setting should my Airport Extreme Base Station use.
    The Computer system says 10.0.1.1 and it works. When I entered the numbers they suggested I get no connection.
    Any suggestions?

    To change DNS setup on the Airport you need to put in the DNS change on the Internet tab. The Airport will always place itself as the main DNS server to the network clients that connect by DHCP, unless you set the Airport to static IP.. and it will use your ISP DNS server by default.. you can change them if you want. Just type in the new DNS you want to use.
    This month's MacWorld suggests that changing the DNS setting of the wireless device might increase the speed of the connection.
    http://www.macworld.com/article/2824564/slow-internet-edit-your-dns-settings.htm l
    In most cases this is really so minimal as to be insignificant. The airport should cache the regularly used DNS addresses and you can test it by ping to your local DNS or the DNS recommended by MacWorld??.. but honestly a few ms is not going to change the world. To the clients the local network addressing should be still using the Airport as the main DNS.. you can setup manually in each device a different DNS but that can give local network issues as it then has to find local clients by broadcast.
    I have a complex dns setup for other reasons.. getting past geolocks..
    If I ping my local ISP dns I get
    ping 202.76.170.228
    PING 202.76.170.228 (202.76.170.228): 56 data bytes
    64 bytes from 202.76.170.228: icmp_seq=0 ttl=61 time=25.422 ms
    64 bytes from 202.76.170.228: icmp_seq=1 ttl=61 time=25.984 ms
    64 bytes from 202.76.170.228: icmp_seq=2 ttl=61 time=25.504 ms
    64 bytes from 202.76.170.228: icmp_seq=3 ttl=61 time=24.933 ms
    64 bytes from 202.76.170.228: icmp_seq=4 ttl=61 time=25.297 ms
    64 bytes from 202.76.170.228: icmp_seq=5 ttl=61 time=25.258 ms
    64 bytes from 202.76.170.228: icmp_seq=6 ttl=61 time=24.915 ms
    If I ping google DNS. 8.8.8.8
    ping 8.8.8.8
    PING 8.8.8.8 (8.8.8.8): 56 data bytes
    64 bytes from 8.8.8.8: icmp_seq=0 ttl=57 time=37.985 ms
    64 bytes from 8.8.8.8: icmp_seq=1 ttl=57 time=37.562 ms
    64 bytes from 8.8.8.8: icmp_seq=2 ttl=57 time=37.715 ms
    64 bytes from 8.8.8.8: icmp_seq=3 ttl=57 time=37.639 ms
    64 bytes from 8.8.8.8: icmp_seq=4 ttl=57 time=36.845 ms
    If I ping the US DNS server.
    ping 208.122.23.22
    PING 208.122.23.22 (208.122.23.22): 56 data bytes
    64 bytes from 208.122.23.22: icmp_seq=0 ttl=51 time=187.209 ms
    64 bytes from 208.122.23.22: icmp_seq=1 ttl=51 time=187.398 ms
    64 bytes from 208.122.23.22: icmp_seq=2 ttl=51 time=186.681 ms
    64 bytes from 208.122.23.22: icmp_seq=3 ttl=51 time=187.030 ms
    64 bytes from 208.122.23.22: icmp_seq=4 ttl=51 time=186.731 ms
    64 bytes from 208.122.23.22: icmp_seq=5 ttl=51 time=186.967 ms
    It is very obvious the best ping is the ISP dns because the route path is shorter..
    Google is very good but still takes longer and of course dns in another country is much worse.

  • Does firmware update 7.1 break the Airport Extreme Base Station?

    Does firmware update 7.1 break the Airport Extreme Base Station?
    See Digg
    http://www.jayhaynes.net/2007/04/donot_install.html
    April 10, 2007
    Do NOT install AirPort 802.11n Firmware 7.1
    This Firmware 7.1 update for AirPort Extreme Base Station with 802.11n should definitely NOT be installed.
    Here was my problem:
    I used AirPort Utility 5.1 to install the update. It is automatic - launch the utility and it asks if you want to install the update. I said yes because I had problems getting two AirPort n base stations networking together to extend my range (I gave up finally and just used an AirPort Express to extend the range).
    After the firmware update, some sites would not load at all (www.nytimes.com) and others took forever to load. And worse, I could not send any email from any of my IMAP accounts. It seemed to be a DNS problem.
    I have two 802.11n AirPorts, so I finally went back to the other one (7.0) and everything worked fine. The Apple tech support guy offered to replace my broken (7.1) AirPort.
    Foolishly, I wanted to make sure the problem was actually with the 7.1 update and not the AirPort itself. So I updated my second 802.11n base station with 7.1. And it casued the exact same problem (some sites not loading, no outgoing email).
    The Apple tech (at this point I was speaking with a wireless specialist) put me on hold to test a few of his AirPorts to see if he could revert back to firmware 7.0 or (ii) install a clean version of 7.1 (in case the version on my drive was corrupted).
    Unfotunately neither option was possible, which is a design flaw in AirPort Utility.
    Apple is sending me two new AirPorts in 1-2 days, which is great service, but I will not be installing firmware update 7.1 again. Fool me once...
    http://www.apple.com/support/downloads/airportextremebasestationwith80211nfirmwa re71.html
    AirPort Extreme Base Station    

    Turns out that the firmware 7.1 does not render the AEBS useless.
    My problem was resolved when I turned off my DSL modem, the AEBS and the computer. Then restarted in same order going to the next one after the first is compeletly up and running. I had no problems whatsoever after that.
    Seems that the firmware update makes the IPs 'stick' somehow. I would think that even a reset of AEBS might have done it but I never got to that stage.
    All my computers came alive in no time.
    I suggest Smith tries this. Simply reset the whole network. Ah yes, my cable modem has an internal battery, I needed to disconnect this too. Only then did the modem go into the 'acquiring' or 'distribution' mode.

  • Airport Extreme Base Station Internet Connection issue

    I have a connection question for Airport Extreme Base Station.
    I have Comcast cable broadband. I connect that to a Linksys router for
    use with my Vonage phone, and then from the Linksys router I connect
    via Ethernet to my iMac. I like the direct Ethernet connection for
    performance reasons.
    In order to set up a home network to connect my Tivo's (and eventually
    my PC and printer), I have set up an Airport Extreme Base station and
    connected it to the Linksys router from it's ethernet connection to the
    WAN (cable modem) input on the Extreme.
    I have connected to the Airport network with my iMac, but since I am
    connected to the Internet via Ethernet, I cannot tell if my Airport is
    connected to the Internet so that I can use it for my Tivo. My PC is
    still in storage from a move, so I can't check with that.
    My question: How can I tell if my Airport is connected to the Internet
    without disabling my Ethernet connection on my iMac?
    A few more info points/questions in case it helps answer:
    1) I previously used this Airport to connect this iMac wirelessly.
    2) Should I be connecting it to the LAN port since it's coming out of
    the router?
    3) If the connection issue is because I am going through the Linksys
    first, can I connect the modem to the airport and then use the LAN port
    to connect to the Linksys router?
    4) If I have to disable the ethernet connection to test the Airport,
    how do I do it? Just unplug it?
    I appreciate any help as the online and manual help from Apple is not
    quite up to par with such a complex configuration.
    Regards
    Bill

    2) Should I be connecting it to the LAN port since it's coming out of
    the router?
    No, connecting to the WAN port is fine.
    3) If the connection issue is because I am going through the Linksys
    first, can I connect the modem to the airport and then use the LAN port
    to connect to the Linksys router?
    The issue is that you have two routers which effectively creates two networks. Unless this was your original intent, you will want to setup the AEBS as a bridge.
    To set up the AirPort Extreme Base Station (AEBS) as a bridge, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, make these settings:
    Network tab
    - Distribute IP addresses (unchecked)
    - Apply the new settings.
    - Wait at least 5 minutes.
    4) If I have to disable the ethernet connection to test the Airport,
    how do I do it? Just unplug it?
    Well, that's certainly one way, but an easier way is to temporarily disable the "Built-in Ethernet" in your network configuration.
    System Preferences > Network > Show > Network Port Configurations
    - Built-in Ethernet (unchecked)

  • HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
    Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
    As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
    Is there a way to resolve this issue?

  • Airport Extreme Base Station as bridge for Westell DSL router

    I have searched the forums & internet and for the life of me cannot get my network to work properly! I hope you can help.
    Here is the situation (I rent so chances are we will not be moving hardware anywhere):
    - Westell (Verizon) DSL wireless router downstairs connected to the internet, 1 iMac via ethernet, and 2 ibooks via Airport cards
    - One lonely Powermac G4 upstairs that does not have a wireless card
    - One extra Airport Extreme Base Station with firmware version 5.7 installed & connected via ethernet/LAN to the G4
    I figured the "easy" thing to do would be to use the AEBS as a wireless bridge to get the G4 online. The network utility has occasionally thought that the G4 was connected to the internet, but the internet didn't work at all when it said that!
    I have been configuring the AEBS using my wireless ibook (G3). I "unchecked" distribute IP addresses, and "checked" connect to network via WDS. I used the Westell's MAC address as the main WDS source. Under the "WDS" tab, I said to configure the AEBS as a remote station and the Westell router as the main station, and to allow wireless users to connect.
    I have tried using the same Network name for each. WEP/WAP is NOT set up on either modem, so passwords aren't a problem. They are both set to channel 6. I am configuring the TCP/IP settings manually.
    When the network names are the same, the internet either stops working, or the computers can't find the AEBS.
    I don't understand why the AEBS seems unable to see the DSL network.

    Hi,
    Well, what I have been able to do is this:
    I have a Westell Wireless DSL router, just like the one mentioned here, and just like the one mentioned in the article I made reference to, the one started by Mr. Müller.
    As was mentioned in the Mr. Müller article, there are some possibilities that will work. They were submitted by a guy named Duane, from Texas. He gives three alternate possibilities, which he entitled "Solution #1, Solution #2, and Solution #3. He says all three of these alternatives will work, and in reading them over I came to the following conclusions: First, he really knows his stuff, and second, his proposed solutions would probably work.
    Based on his comments I decided to take a risk yesterday - I put my older Mac Base Station in a drawer and invested in a new Airport Extreme.
    Anyway, I digress...
    What I've done is follow Solution #3. And it works! I now have a connection from my laptop to the Airport Extreme base station and the internet. I am typing this message using that connection. All I had to do was disable the wireless connection of the DSL router (using their software, of course), and connect the Airport Extreme, via the LAN Ethernet connector, to the Westel DSL router.
    Now, all that remains for me is to extend the range of the base station, using an Airport Express. I haven't had any success with that yet, but I see no reason why I shouldn't get it to work eventually. If you can help me out with that, though, I'd sure appreciate it.
    Best regards,
    Patrick
    Macintosh G5, Powerbook G4   Mac OS X (10.4.7)  

  • Cannot see Airport Extreme Base Station--Watch for 2.4Ghz traffic!

    (Issue is addressed in the body of this post)
    Great when working on 802.11n at 5Ghz, BUT...
    If you have to be compatible with 802b/g you are forced to transmit at 2.4Ghz. Traffic at this frequency can be so bad that it made my station invisible (even with "Interface Robustness" activated). The "automatic channel selector" is supposed to choose a clutter free channel for clear communications, but it does not work well. I had to reprogram the station (through ethernet) to manually change the channel to a more stable one. In my case, channel 8 did the job.
    After this, the Airport base worked perfectly!
    I live in a condo area where I get 8 strong wireless networks, all at the same time. Add microwave ovens, TV's and cordless phones and you get a jammed 2.4Ghz highway. Make sure to select a channel that provides seagway to the "carpooling lane".

    Bob - Thanks so much for your quick reply. I followed your suggestions and, to go into perhaps unnecessary detail, I'll write what I did. I completely disconnected the Airport Extreme Base Station (AEBS) from my computer. I disabled Windows Firewall, uninstalled my anti-virus program, and uninstalled Airport Utility and Bonjour, recycled by cable modem (took out the battery and unplugged it for about 20 seconds), then restarted my computer. After the computer booted up, I verified that windows firewall was disabled, reinstalled Airport Utility and Bonjour, then reconnected the cable connecting the AEBS to the computer (to one of the three ethernet ports, and I tried each of them in case one was faulty) but not to the cable modem as my firewall was disabled and had no anti-virus software. I also reconnected the AEBS power chord. I opened the newly reinstalled Airport Utility software and it did not find the base station. Only when I used "configure other" was I able to access the AEBS. I recycled the modem again, but that did not help. I turned on the firewall, installed anti-virus software, connected the AEBS to the modem, the light turned green, and I was able to access the internet on the primary computer and the wireless network gave me internet access on my laptops. But I was still not able to have my main computer, the one directly connected to the AEBS able to see it, and configure it, without utilizing "configure other."
    Also, any idea why one of my laptops can only access the "guest" network? When it attempts to connect to the primary network it will stay on "acquiring network address" for what seems a few minutes, then switch to the "guest" network and connect immediately.
    Any help would be greatly appreciated.

  • How do I open the same ports on an Airport Extreme Base Station for multiple computers at the same time?

    As the title suggests...
    I have a mix of five Mac and PC's at home using an Airport Extreme Base Station as the router.   I need many ports opened on the AEBS for all of the computers- not just one computer.  (for example: three people want to play TF2 on Steam at the same time; each machine needs the correct ports open on the router).   Port forwarding  only allows me to forward a given port to a single IP, yet I need that port open for five differnt IP's, all at the same time. 
    How do I do that on an AEBS?
    In the same way, I have a small office of four iMacs using an old airport with the same exact issue.   I would like to be able to connect to all of them remotely with Apple Remote Desktop, but the port forwarding on the airport only allows a port to forward to a single IP.   I want to be able to tunnel into the office network and log onto any machine behind the Airport extreme... not just a single IP.    I currently have it set up where I can tunnel into the office from my house, I can find the one machine that the port forwarding has been assigned to, I can log on and everything is just fine... with one machine.    How do I open the firewall for the other machines? 
    TL,DR version:  How do you open ports on an Airport Extreme Base Station instead of forwarding ports?   Forwarding ports doesn't work for multiple IP's.  

    You can open a single or multiple ports to a single device or different ports to different devices, but you cannot open the same port to multiple devices via the AirPort Utility for the Apple routers.

  • Define static IP for both LAN and W-LAN devices with an Airport Extreme Base Station

    Hey guys,
    I have a lot of different devices connected to my Airport Extreme Base Station (5th Gen) either wirelessly or via ethernet cable. Since I control some of them via VNC and currently have to find the corresponding IP-addresses through trial-and-error, I'd like to define static IP-addresses for the computers in question. My network consists of a cable modem connected to a TP-Link WR1043ND router in the basement, from which an ethernet cable leads to the WAN-port of the aforementioned Airport Extreme Base Station on the 2nd floor. Two of the devices I want to remote-access are  wired to a D-Link DES-1005D switch, which in turn is connected to the 1st ethernet port of the Airport Base Station. The remaining 3 remote clients are connected over 802.11n. All computers run Windows.
    My problem now is that even though I was able to define static IP-addresses employing the "DHCP only" router mode, this didn't seem to work for the two computers connected via ethernet. Not only did I lose any internet connectivity with those, I even lost the ability to remote-connect to them using the VNC-viewer.
    The question now is: how do I specify static IP-addresses for my ethernet devices correctly?
    I hope you can help me.

    My network consists of a cable modem connected to a TP-Link WR1043ND router in the basement, from which an ethernet cable leads to the WAN-port of the aforementioned Airport Extreme Base Station on the 2nd floor.
    If you read the information in the other post, my answer would be the same here.
    The Router Mode of DHCP Only is rarely used, and would only really be appropriate if your ISP was providing you with a fixed bank of multiple fixed or static IP addresses to use. This does not appear to be the case in your post.
    If this were the case, the first IP address would be used as a Static IP address for your connection, and other devices on your network would receive the other fixed IP addresses.
    99%+ of the time, you would use the Router Mode setting of DHCP and NAT on a network when you want the AirPort to perform as the main router for the network.
    But......your post also indicates that you have another router upstream on your network from the AirPort Extreme.  You would not want to run two routers in series on a network. That explains the problems that you are having.
    The AirPort Extreme needs to be configured in Bridge Mode. It cannot be the "main" router on your network when you already have another router on the network. That is a fundamental networking rule.

  • I have a Cisco wireless router.  Can I buy an Airport Express plug in booster for a distant part of my house or do I need an Airport Extreme base station instead to make the Airport Express plug in booster work?

    Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?

    You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
    Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
    Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
    Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
    If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
    The bottom line here......you always need two Apple routers if you want to extend the network wirelessly.

  • I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light.

    I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?

    apikoros wrote:
    The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
    1)  I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access.  But do I have to  change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
    Resetting the password you will need to do for each device... the utility cannot even see those old units.
    So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
    2)  Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
    N.Korean hackers.
    [Edit] Whoops-- one more question:  I want to partition the TC's disk, but Disk Utility doesn't see it.  What do I need to do?
    You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
    Look at Q3 here.
    http://pondini.org/TM/Time_Capsule.html
    Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

  • Third party Device connection to Airport Extreme Base Station

    I have a new Airport Extreme Base Station (AEBS) that my iMac is wirelessly connected too. I cannot connect my HP wireless printer to the AEBS. The printer recognizes the SSID and WEP password, but does not have a connection & does not print.
    I also, cannot connect a Netgear Wireless Bridge for (xBox) to the AEBS. The xBox does not see the SSID at all. What do I do??? I purchased the AEBS because the salesman said it would be the easiest wireless network ever, but I only have problems ! ! ! ! ! ! !
    Aaron
    iMac G5   Mac OS X (10.3.9)  

    Very likely a WEP issue.
    If you turn off WEP can you now connect and print?
    One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
    In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
    The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
    One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
    Though sometimes not even that works and the HEX key must be used regardless.
    AirPort: Joining an encrypted wireless network
    http://docs.info.apple.com/article.html?artnum=106424
    Choosing a password for networks that use Wired Equivalent Privacy (WEP)
    http://docs.info.apple.com/article.html?artnum=108058
    iFelix

  • I have a MacBook ProDo I have to have the Airport Extreme Base Station for my Airport Express to work?

    I cannot get the darn Airport Express to work!  It just keeps blinking Amber.  I know it must be something silly I am over looking.  And I do not have the Airport Extreme Base Station.
    Thank you for any help!!!
    Elizabeth

    Thanks,
    This is the rear of your modem/router:
    Connect a Cat5e or Cat6 cable from any of the 4 Ethernet Lan ports to the (single) socket on the Express, then go to Airport Utility (Applications>Utilities>Airport Utility) and select create a new network.
    You will need to turn the wireless transmiter in the Netgear off, here is a link to the Netgear Manual in case you need to refer to it.
    Netgear Manual

  • I have an Apple AirPort Extreme Base Station (Simultanious Dual_Band) (MC340LL/A), and updated the software.  After updating no devices can connect via wifi.  Any suggestions.

    I have an Appl,e AirPort Extreme Base Station (Simultaneous Dual_Band( MC340LL/A.  After updating the software, no devices can connect via wifi.

    As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.

  • Software to install Airport Extreme Base Station

    Hi all,
    Any idea how I'd re-install the Airport Extreme Base Station? I lost the disk that came with it.
    Thanks for your help,
    Chelsea

    chelsea_marti, Welcome to the discussion area!
    There is no need to re-install anything. The "AirPort Admin Utility" and "AirPort Setup Assistant" are in the /Applications/Utilities folder on your Mac.

Maybe you are looking for

  • My iPhone 4s is retaining all emails in its inbox yet I am deleting them in Outlook. How do I get it to sync with my outlook account and delete the emails?

    My iphone 4s is retaining all of my  emails in it's inbox. I have been deleting emails in outlook but they are not deleting on the iphone. How do I set up my iphone so it is a secondary account and syncs with outlook on my Mac?

  • Printing Footer in List

    Dear Guys I am trying to write a list which will show PAGE-NO and DATE at the end of footer. I am trying the folowwing code but footer is not appearing. Code: LINE-COUNT 65(01) NO STANDARD PAGE HEADING <b>TOP-OF-PAGE. PERFORM HEADER. PERFORM SUB_HEAD

  • SLA Alerts in DB polling proxy

    Hi I have created a DBAdapter to poll a table in the database for any inserts/updates. Have adopted the Logical Delete processing. Now I need to configure an SLA alert for the proxy service based on this DBAdapter. The alert needs to be raised when n

  • Multiple sites on iweb

    Okay, let me try to explain just one more time... I currently have a website published through iweb and I used godaddy to set up my personal domain name for the website. I now would like to create a totally different site using a completely different

  • HT4972 4th gen touch ios 7 how to install

    4th gen touch ios 7 how to install,and can't get old store id changed I changed it every were but when try to up date apps puts old id up won't take new password.Ios7 I loaded and tryed shift key in itunes to get installed and won't take does this me