4.1.5B Breaks PPTP connection

Hello All - I have a VPN 3005 and W2K and XP clients connecting via MS VPN PPTP that was working with firmware version 4.0.5.A and bootrev 2.5 just fine. Updated firmware to 4.1.5.B and my users can authenticate (radius) but can neither ping nor resolve DNS. ipconfig info looks fine on the client. I downgraded to 4.0.5.B and it works fine again. Is there a problem with the 4.1.5.B firmware and the boot rev on this particular concentrator? I saw a note concerning the boot rev 2.5 and concentrators with serial#'s starting with CAM. Something about MAC Addresses being incorrectly reported. Or is it an incompatibility between MS VPN and rev 4.1.5.B? Need to setup and test WEbVPN. Any suggestions appreciated.
Thank in advance,
JAP

I had the exact same issue with VPN 3015 after upgrading to 4.1.5.B. It forced all our users to ipsec. I'd be interested to see if you find a solution.
Todd

Similar Messages

ASA 5505 Problem with outbound PPTP-connection on non-native vlan

Hi, why am I not being able to make a PPTP connection on vlan80 (trunked to AP Cisco 1142N) compared to vlan10? And yes, I've configured the "
inspect pptp"
ASA 5505 with sec plus license

Hi mate,
I don't know how to solve your problem but I strongly reccommend you to remove your password from the first post and to update it on your ASA device

Need help with setting up a PPTP connection

Hello all,
I am having trouble setting up a PPTP connection in Mac OS X "Snow Leopard". The ISP has provided the following info:
— Protocol: PPTP
— Login
— Password
— IP Address
— Subnet mask
— Default Gateway
— IP Address of the VPN Server
I am using the Airport Express as rounter, so here's what I entered in the Airport Utility on the Internet tab:
Connection: Ethernet
IP Address (as provided)
Subnet mask (as provided)
Router address (from Default Gateway)
Then I went to Connections, and created a new PPTP connection, setting the properties of the latter as follows:
VPN Server (as provided)
Account name (from Login)
Authenrification->Password (from Password)
and chose "Send all traffic over VPN connection".
The Airport is reported to have connected successfully, but the specified VPN Serverd does not ping, and when I try to connect via PPTP, an error is displayed saying that the PPTP-VPN server did not respond. Playing with different Encryption types did not help.
This same connection, when set up on a Windows machine, works well so I think I must have goofed with the Mac OS X settings. Could you help me find out what I could have done wrong?
Thanks in advance,
Anton

Pete Corelio:
{quote}You do have more network devices, at least a dsl or cable modem and maybe a switch connected to it. Are your PC and the AX connected to the same modem/switch?{quote}
No. There's only the Ethernet cable leading to some central (building-wide, or even wider) device. It was routed to my friend's apartment by the ISP people.
{quote}It's a bit uncommon to manually set the IP address within the TCP/IP section of the VPN network settings like you did. That's usually set to automatically get an IP via PPP... Please try a quick test using PPP instead.{quote}
Having the AX using DHCP and VPN using PPP makes part of the ISP settings unnecessary... Hmmm. Anyway, I did try PPP in VPN connection settings, to no avail. Alas.
{quote}It's also suspicious that you cannot open a connection to port 1723 with the telnet command. Are you sure the VPN type is PPTP and not LT2P over ipsec?{quote}
Yes, I am sure. The ISP's support confirmed it over the phone. Also they said they hadn't been able to set up any Mac with their network, but I am loth to believe the latter statement. And I clearly remember it was PPTP (not LT2P) in the Windows settings.
{quote}lease verify the IP settings on your PC...{quote}
OK, will do this Wednesday. Also I'll take a closer look at the VPN settings.
{quote}So your PC is on the same network and the VPN works from there? Is the PC using 3rd party VPN software or the built-in software?{quote}
No other clients, just a VPN connection configured using Windows built-in tools.
Anton
EDIT:
{quote}'m assuming the Mac gets an IP in the 10.x range and gets online OK right? {quote}
The AX is saying it's connected but there's no internet. This ISP is providing access to the internet through that VPN. The same AX works well with my MacBook at home, although I am using PPPoE.
Message was edited by: Ant_222

PPTP connection stall, but still "connected"

Hi,
I just bought new iMac 2 wks ago. It comes with Lion 10.7.2.
Got problem on PPTP connection to my work.
Basically, I can create a PPTP setup (VPN) and make connection work. However, it won't last for long, at most 15-20 min, all web request just hang and existing ssh connection will be kicked out with "broken pipe" message.
I use PPTP with Max 128bit encryption. And also have a "Domain\Username" format login ID and a password as credential. I also let all my network flow go through this VPN.
Please help on this issue. Hope there is someone having the same problem and share the solution .

I have the same problem with my iMac 24 & iMAc 27, both with Lion 10.7.2.
I use PPTP with out encryption.
I don't find any solution

AirPort Extreme Crash during PPTP connect using VPN on demand

I can reproduce this crash consistently every time.
My AEBSn is running 7.4.2. My MBP is running 10.6.2.
I set up a PPTP connection, tick "send all traffic over VPN connection" in the advanced options.
I add a domain to the "VPN on Demand" list and apply changes.
I click connect, and the AEBS light immediately goes amber. A few seconds later, it's back to green and everything is groovy...unless I try to connect again.
The problem is solved by simply removing the domain from "VPN on Demand."
Here's the relevant snippet from ppp.log:
Sat Jan 30 00:22:36 2010 : PPTP connecting to server 'xxxx.xxxx.xxx' (xx.xxx.xx.xx)...
Sat Jan 30 00:22:37 2010 : PPTP connection established.
Sat Jan 30 00:22:37 2010 : Using interface ppp0
Sat Jan 30 00:22:37 2010 : Connect: ppp0 <--> socket[34:17]
Sat Jan 30 00:22:40 2010 : pptpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.14), deleted interface setting (name: en0, family: Ether, address: 10.0.1.14, subnet: 255.0.0.0, destination: 10.0.1.255).
Sat Jan 30 00:22:40 2010 : linked service found: Setup:/Network/Service/C1126C24-140A-4AE4-A35D-553148185E2F/Interface
Sat Jan 30 00:22:40 2010 : starting wait-interface timer for pptp: 20 secs
Sat Jan 30 00:22:51 2010 : pptpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.14), deleted interface setting (name: en1, family: Ether, address: 10.0.1.5, subnet: 255.0.0.0, destination: 10.0.1.255).
Sat Jan 30 00:23:00 2010 : pptpwait_interfacetimeout: 20 secs TIMEOUT waiting for interface to be reconfigured. previous setting (name: en0, address: 10.0.1.14).
Sat Jan 30 00:23:00 2010 : PPTP has detected change in the network and lost connection with the server.
Sat Jan 30 00:23:00 2010 : Connection terminated.
Sat Jan 30 00:23:00 2010 : PPTP disconnecting...
Sat Jan 30 00:23:00 2010 : PPTP disconnected
Funny, huh?

Hi
I have had this problem with my Airport Extreme since day 1 and it is extremely irritating. Using Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2003 I can crash the router any time I like (or more to the point, really really dislike) by simply initiating a PPTP VPN from any client (wired or wireless) behind the Airport Extreme. The device flashes orange, drops everyone's internet connection and then about a minute later, comes back up again.
Whenever I have to connect to another site using VPN, I need to use NextG internet connection instead of my home cable connection. Any help with this would be gold because other than this really annoying problem (oh and the 'must reboot everytime you make a minor modification to configuration' requirement) I find it a great rock solid wireless access point.

WRV200 dropping VPN/PPTP connections

I replaced an aging router with a WRV200 on recommendation from two sources. Everything is working nicely except inbound PPTP connections on port 1723. TCP1723 is forwarded to the correct IP address internally. Everything is wired with wireless disabled. When a client connects, they get dropped after about 3 or 4 minutes. Clients are also unable to connect if their local Windows Firewall (XP Pro SP2) is enabled. Our previous router didn't have this problem, and if I swap the routers again, the problem goes away. This is with the latest firmware. Please help, my remote users are panicking!

Disable all other firewalls ..... reset the router & reconfigure it ...
See if still it shows the same error ...

Tiger VPN (PPTP) connection issues

Hello everyone.
I'm having major issues trying to connect to office VPN from home; hoping someone can point me in the right direction. (And my profound apologies in advance for the long post -- just trying make sure to include enough detail to debug whatever might be happening)
At the office we have a 3Com OfficeConnect VPN Firewall sitting in front of a Microsoft 2003 Exchange server. (3Com product page for this VPN box is http://www.3com.com/products/en_US/detail.jsp?tab=features&sku=3CR870-95&pathtyp e=purchase). Home connection is a Linksys WRT54GL wireless router in front of a broadband cable modem. PPTP pass-through is enabled in the router config.
At home I have a WinXP-SP2 laptop and my G4 Powerbook (OS 10.4.7) sitting side-by-side. From the XP laptop, I can get into the VPN using XP's built-in client without any problems. The DNS lookup and authentication steps take about 2-3 seconds combined. Once the connection is established, both external sites (cnn.com) and internal sites (intranet.companyname.local) load in a browser window without any appreciable delay. I can also access Windows shared drives on the internal network without problems, including large (10's of MB or more) file copies to/from the XP laptop's HD.
On the Powerbook, using Tiger's built-in VPN client, I can connect OK (though the authentication step takes a bit longer, about 4-5 seconds), but after that, almost nothing works. I can ping the internal DNS server, but after a few pings with reasonable delays (~15 millisecond range), the round-trip times suddenly jump to handfuls of seconds. In the browser, trying to load an internal webpage (http://intranet.companyname.local) times out before anything shows up on screen. In Finder, using Go>Connect to Server... very slowly establishes the connection (~10-15 seconds or longer), and sometimes opens a Finder window... but then invariably times out. I have never once had the connection remain stable enough to transfer so much as a single file from the shared volume onto the Powerbook's Desktop before it times out and disconnects.
On the XP machine, relevant(?) VPN config settings are:
require secured password
require data encryption (disconnect if none)
PPTP VPN
LCP extensions enabled
software compression enabled
multi-link negotiation for single link connections DISABLED
server type = PPP
transports = TCP/IP
authentication = MS CHAP
encryption = MPPE 128
compression = none
PPP multilink framing = off
and, once the VPN connection is established, parameters are (from "ipcofig /all"):
Windows IP Configuration
Host Name . . . . . . . . . . . . : (companyname)-hj2
Primary Dns Suffix . . . . . . . : (companyname).local
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : (companyname).local
Ethernet adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Intel(R) PRO/Wireless 2915ABG Network Connection
Physical Address. . . . . . . . . : XX-XX-XX-XX-XX-XX
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.1.104
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DHCP Server . . . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.1.1
PPP adapter (ConnectionName):
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface
Physical Address. . . . . . . . . : XX-XX-XX-XX-XX-XX
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 172.16.0.70
Subnet Mask . . . . . . . . . . . : 255.255.255.255
Default Gateway . . . . . . . . . : 172.16.0.70
DNS Servers . . . . . . . . . . . : 172.16.0.11
finally, results of "ping -n 10 (InternalServer)":
Pinging (InternalServer).(companyname).local [172.16.0.5] with 32 bytes of data:
Reply from 172.16.0.5: bytes=32 time=4ms TTL=128
Reply from 172.16.0.5: bytes=32 time=10ms TTL=128
Reply from 172.16.0.5: bytes=32 time=10ms TTL=128
Ping statistics for 172.16.0.5:
Packets: Sent = 10, Received = 10, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 4ms, Maximum = 10ms, Average = 9ms
On the Powerbook, I have a VPN (PPTP) connection set up with "Send all traffic over VPN connection" unchecked. In the Network panel of System Preferences, I have tried manually adding (and removing) "local, (companyname).local" in the Search Domains line, and manually adding (and removing) the IPs of our internal DNS servers (172.16.0.5, 172.16.0.11) under the TCP/IP tab. Proxies are turned off in all cases.
With those settings, the relevant(?) parts of running "ifconfig" from a Terminal window after starting the VPN are as follows:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::XXX:XXXX:XXXX:XXXX%en1 prefixlen 64 scopeid 0x5
inet 192.168.1.100 netmask 0xffffff00 broadcast 192.168.1.255
ether XX:XX:XX:XX:XX:XX
media: autoselect status: active
supported media: autoselect
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
lladdr XX:XX:XX:XX:XX:XX:XX:XX
media: autoselect <full-duplex> status: inactive
supported media: autoselect <full-duplex>
ppp0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1444
inet 172.16.0.69 --> 172.16.0.11 netmask 0xffff0000
The associated connection log from Internet Connect is:
Tue Jul 18 08:50:57 2006 : PPTP connecting to server 'vpn.(companyname).com' (XXX.XXX.XXX.XXX)...
Tue Jul 18 08:50:57 2006 : PPTP connection established.
Tue Jul 18 08:50:58 2006 : using link 0
Tue Jul 18 08:50:58 2006 : Using interface ppp0
Tue Jul 18 08:50:58 2006 : Connect: ppp0 <--> socket[34:17]
Tue Jul 18 08:50:58 2006 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xb851f701> <pcomp> <accomp>]
Tue Jul 18 08:50:58 2006 : rcvd [LCP ConfReq id=0x1 <mru 1492> <auth chap MS> <magic 0x80697000>]
Tue Jul 18 08:50:58 2006 : lcp_reqci: returning CONFACK.
Tue Jul 18 08:50:58 2006 : sent [LCP ConfAck id=0x1 <mru 1492> <auth chap MS> <magic 0x80697000>]
Tue Jul 18 08:50:58 2006 : rcvd [LCP ConfRej id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
Tue Jul 18 08:50:58 2006 : sent [LCP ConfReq id=0x2 <magic 0xb851f701>]
Tue Jul 18 08:50:58 2006 : rcvd [LCP ConfAck id=0x2 <magic 0xb851f701>]
Tue Jul 18 08:50:58 2006 : sent [LCP EchoReq id=0x0 magic=0xb851f701]
Tue Jul 18 08:50:58 2006 : rcvd [CHAP Challenge id=0x1 <4f0656add65818c2>, name = "Guest"]
Tue Jul 18 08:50:58 2006 : sent [CHAP Response id=0x1 <0000000000000000000000000000000000000000000000004c86e5ccf08b95431034ef14706021 d358dc21b96a59157301>, name = "(UserName)"]
Tue Jul 18 08:50:58 2006 : rcvd [LCP EchoRep id=0x0 magic=0x80697000]
Tue Jul 18 08:50:58 2006 : rcvd [CHAP Success id=0x1 "Authentication succeeded, welcome!"]
Tue Jul 18 08:50:58 2006 : CHAP authentication succeeded: Authentication succeeded, welcome!
Tue Jul 18 08:50:58 2006 : Disabling 40-bit MPPE; MS-CHAP LM not supported
Tue Jul 18 08:50:58 2006 : sent [CCP ConfReq id=0x1 <mppe +H -M +S -L -D -C>]
Tue Jul 18 08:50:58 2006 : rcvd [IPCP ConfReq id=0x1 <addr 172.16.0.11> <ms-dns3 0.0.0.0> <ms-wins 0.0.0.0>]
Tue Jul 18 08:50:58 2006 : sent [IPCP TermAck id=0x1]
Tue Jul 18 08:50:58 2006 : rcvd [CCP ConfReq id=0x1 <mppe +H +M +S +L -D -C>]
Tue Jul 18 08:50:58 2006 : sent [CCP ConfNak id=0x1 <mppe +H -M +S -L -D -C>]
Tue Jul 18 08:50:58 2006 : rcvd [CCP ConfAck id=0x1 <mppe +H -M +S -L -D -C>]
Tue Jul 18 08:50:58 2006 : rcvd [CCP ConfReq id=0x2 <mppe +H -M +S -L -D -C>]
Tue Jul 18 08:50:58 2006 : sent [CCP ConfAck id=0x2 <mppe +H -M +S -L -D -C>]
Tue Jul 18 08:50:58 2006 : MPPE 128-bit stateless compression enabled
Tue Jul 18 08:50:58 2006 : sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
Tue Jul 18 08:50:58 2006 : sent [IPV6CP ConfReq id=0x1 <addr fe80::020a:95ff:fea5:564c>]
Tue Jul 18 08:50:58 2006 : sent [ACSCP] 01 01 00 10 01 06 00 00 00 01 02 06 00 00 00 01
Tue Jul 18 08:50:58 2006 : rcvd [LCP ProtRej id=0x1 80 57 01 01 00 0e 01 0a 02 0a 95 ff fe a5 56 4c]
Tue Jul 18 08:50:58 2006 : rcvd [LCP ProtRej id=0x2 82 35 01 01 00 10 01 06 00 00 00 01 02 06 00 00 00 01]
Tue Jul 18 08:50:58 2006 : rcvd [IPCP ConfRej id=0x1 <ms-dns3 0.0.0.0>]
Tue Jul 18 08:50:58 2006 : sent [IPCP ConfReq id=0x2 <addr 0.0.0.0> <ms-dns1 0.0.0.0>]
Tue Jul 18 08:50:58 2006 : rcvd [IPCP ConfNak id=0x2 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:50:58 2006 : sent [IPCP ConfReq id=0x3 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:50:58 2006 : rcvd [IPCP ConfAck id=0x3 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:51:01 2006 : sent [IPCP ConfReq id=0x3 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:51:01 2006 : rcvd [IPCP ConfAck id=0x3 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:51:04 2006 : sent [IPCP ConfReq id=0x3 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:51:04 2006 : rcvd [IPCP ConfAck id=0x3 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:51:07 2006 : sent [IPCP ConfReq id=0x3 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:51:07 2006 : rcvd [IPCP ConfAck id=0x3 <addr 172.16.0.69> <ms-dns1 172.16.0.11>]
Tue Jul 18 08:51:08 2006 : rcvd [IPCP ConfReq id=0x1 <addr 172.16.0.11> <ms-dns3 0.0.0.0> <ms-wins 0.0.0.0>]
Tue Jul 18 08:51:08 2006 : ipcp: returning Configure-REJ
Tue Jul 18 08:51:08 2006 : sent [IPCP ConfRej id=0x1 <ms-dns3 0.0.0.0> <ms-wins 0.0.0.0>]
Tue Jul 18 08:51:08 2006 : rcvd [IPCP ConfReq id=0x2 <addr 172.16.0.11>]
Tue Jul 18 08:51:08 2006 : ipcp: returning Configure-ACK
Tue Jul 18 08:51:08 2006 : sent [IPCP ConfAck id=0x2 <addr 172.16.0.11>]
Tue Jul 18 08:51:08 2006 : ipcp: up
Tue Jul 18 08:51:08 2006 : local IP address 172.16.0.69
Tue Jul 18 08:51:08 2006 : remote IP address 172.16.0.11
Tue Jul 18 08:51:08 2006 : primary DNS address 172.16.0.11
The problem is that despite this apparently successful negotiation, the VPN connection doesn't really work. If I type "intranet" into the browser URL bar, it doesn't pick it up as "intranet.companyname.local" and instead treats this as a search query, which it passes to google... which times out. If I type "intranet.companyname.local" into the URL bar instead, it appears to do the DNS lookup correctly... but then times out again.
Ping times look like this at first:
PING (InternalServer).(companyname).local (172.16.0.5): 56 data bytes
64 bytes from 172.16.0.5: icmp_seq=0 ttl=128 time=16.605 ms
64 bytes from 172.16.0.5: icmp_seq=1 ttl=128 time=15.920 ms
64 bytes from 172.16.0.5: icmp_seq=2 ttl=128 time=16.154 ms
^C
--- (InternalServer).(companyname).local ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max/stddev = 15.920/16.226/16.605/0.284 ms
... but then if I try it again two seconds later:
PING (InternalServer).(companyname).local (172.16.0.5): 56 data bytes
64 bytes from 172.16.0.5: icmp_seq=0 ttl=128 time=727.144 ms
64 bytes from 172.16.0.5: icmp_seq=1 ttl=128 time=1727.030 ms
64 bytes from 172.16.0.5: icmp_seq=2 ttl=128 time=2727.260 ms
64 bytes from 172.16.0.5: icmp_seq=3 ttl=128 time=3726.747 ms
64 bytes from 172.16.0.5: icmp_seq=4 ttl=128 time=5723.986 ms
64 bytes from 172.16.0.5: icmp_seq=5 ttl=128 time=5719.810 ms
64 bytes from 172.16.0.5: icmp_seq=6 ttl=128 time=6720.334 ms
64 bytes from 172.16.0.5: icmp_seq=7 ttl=128 time=6719.848 ms
^C
--- (InternalServer).(companyname).local ping statistics ---
15 packets transmitted, 8 packets received, 46% packet loss
round-trip min/avg/max/stddev = 727.144/4224.020/6720.334/2176.543 ms
OK, enough for now. Can anyone spot what I might be doing wrong, and/or suggest something to try to remedy this? If there is any additional logging/debug info that would be useful, please ask and I will track it down.
Thanks very much in advance!!! /HJ

Problem not entirely solved, but mostly working now. It turns out the issue was with the 3Com OfficeConnect VPN box. It was causing all sorts of headaches and had to be manually power cycled at least once a week, so we ditched it and got a Linux-based Firewall/VPN appliance (http://www.ingate.com/ingate_vpn.php).
Now I can connect and mount Windows drives via SMB (both the command line and the Finder's "Connect to Server" approach seem to work). Performance still exhibits annoying lags at random times, and occasionally the VPN connection disconnects for no good reason, but at least I can get at my files from home. The other issues -- such as being able to resolve "xxx.yyy.local" addresses in the browser by making sure I hit the internal DNS server before any external ones -- all seem to be network configuration issues on my end.
In short, my guess is that the 3Com box was causing issues with some low-level timing parameters or other related settings in how the VPN connection was being established. I was just starting to teach myself about ARP tables, NTLMv2 authentication, and the like when we replaced it with the new firewall.
Hope this helps.
/Heywood

Cannot establish multiple simultaneous PPTP connections with the CISCO 1841.

Hello everyone;
I have recently tested a PPTP connection with a CISCO 1841 router and got success. I have configured a windows 7 client and successfully connected to the router and was able to access the documents in the server PC that I have mentioned in the attached diagram. I have created number of different users  in the CISCO 1841 too. While some one is having a connection, another user cannot connect to it, which means multiple simultaneous connections aren't possible. Do I have to create a ACL for the PPTP and if yes, How ?
FastEthernet0/0 is up, line protocol is up
Internet address is 192.168.100.1/25
Broadcast address is 255.255.255.255
Address determined by non-volatile memory
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is not set
Inbound access list is 100
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is enabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
IP CEF switching is enabled
IP CEF Feature Fast switching turbo vector
IP multicast fast switching is enabled
IP multicast distributed fast switching is disabled
IP route-cache flags are Fast, CEF
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Policy routing is disabled
Network address translation is enabled, interface in domain inside
BGP Policy Mapping is disabled
WCCP Redirect outbound is disabled
WCCP Redirect inbound is disabled
WCCP Redirect exclude is disabled
Inbound inspection rule is SDM_LOW
--------------------------------------------------------------------------------------------ACL 100-----------------------------
deny icmp any any echo-reply
deny ip host 255.255.255.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip host 66.163.169.186 any
permit ip any any (122467027 matches)

As long as you have the inspection engine enabled on the ASA, it shouldn't freak out of the different IP as it will inspect the call signalling and will NAT it accordingly, BUT, for simplicity, I agree with you, it would cause a lot of troubleshooting headache if there is problem as well as reconfiguration of IP on the host ends.
Here is the NAT FYI:
object network obj-10.10.96.0
   subnet 10.10.96.0 255.255.255.0
object network obj-192.168.96.0
   subnet 192.168.96.0 255.255.255.0
object network obj-10.10.14.0
   subnet 10.10.14.0 255.255.255.0
object network obj-10.1.0.0
   subnet 10.1.0.0 255.255.255.0
object network obj-192.168.1.0
   subnet 192.168.1.0 255.255.255.0
object network obj-10.10.11.0
   subnet 10.10.11.0 255.255.255.0
object network obj-192.168.11.0
   subnet 192.168.11.0 255.255.255.0
nat (inside,outside) source static obj-10.10.96.0 obj-192.168.96.0 destination static obj-10.10.14.0 obj-10.10.14.0
nat (inside,outside) source static obj-10.1.0.0 obj-192.168.1.0 destination static obj-10.10.14.0 obj-10.10.14.0
nat (inside,outside) source static obj-10.10.11.0 obj-192.168.11.0 destination static obj-10.10.14.0 obj-10.10.14.0

Adding a local site to Dreamweaver CC that is through a mapped network drive breaks ALL connections

I am using Dreamweaver CC on Windows 8 on a machine that is hooked up to a local network. My site files are stored on another drive on that network and I am mapped to that drive. I have always been able to open in individual file from that drive in Dreamweaver. But I noticed that with one site I am working on, Dreamweaver would hang trying to make minor revisions to the PHP code. It was suggested to me to add the whole folder as a local site in Dreamweaver, so I did. At first I thought it was moving along much better -- no hanging while I was typing code. Then suddenly I realized I could not save the files. I was no longer connected to the drive I was working on. Even outside of Dreamweaver, I was unable to access the drive. I thought it was a network issue. I rebooted the computer and opened a Windows Explorer folder and was able to access the drive. Then I opened Dreamweaver again and the connection was lost.
To test my theory, I rebooted again, accessed the drive, waited a little while, accessed the drive, then opened Dreamweaver and it was lost. I tried this several times, each with the same result.
Then I went into Dreamweaver, removed the site from Dreamweaver and rebooted. I accessed the drive, opened Dreamweaver, and voila... I could still access the drive. So I tried adding the site back to Dreamweaver and I cannot access the drive after opening Dreamweaver again.
Without having the site in Dreamweaver, the files/Dreamweaver hangs EVERY TIME I TYPE CODE. Adding a site on a mapped local network drive BREAKS MY CONNECTION and disables my ability to work on the files. Is there a reason for this and more importantly, is there a fix? It seems like a very specific but illogical problem.
My next step is to find and install my old Homesite 4.5.
Thanks in advance for any useful advice!

mpendill wrote:
I surely did not knowing change anything within the software!
I just tried adding another site. It seems like it is setting it up and reading the files but then at the end (apparently just as the connection breaks), it gives me these errors:
Cannot create [SITE NAME].
and
The local root folder, [FOLDER NAME], does not exist. Please select a new local root folder by clicking the Manage Sites button.
(I changed the out the actual site name and folder name above.)
I believe these were the same errors I got with the other site. At the time I was pushing a deadline and was too frantic to write it down.
Not that I think it has any relevance, but both sites are Wordpress sites.
Maybe what I should try next is mapping a different drive and trying to set up a site from there?
For that error you want you can try mapping it but it seems your sites root is just not defined... what DW is telling you is it could not find the specified folder when its trying to establish the new site. You might want to make sure your folder is there and all the spelling is correct, when making sure go your your Site Manager and make sure your root site is in your network drive.

Kernel Upgrade Breaks Network Connection

My server uses:
[15:48] (tunix@kulupler ~)$ pacman -Qs kernel
local/kernel26 2.6.19.1-1
The Linux Kernel and modules
local/kernel-headers 2.6.19.1-1
Kernel headers sanitized for use in userspace
for kernel. The latest kernel upgrade (2.6.19.2-1) breaks network connection after ~5 minutes from the boot. When the network connections fails, kernel says:
Jan 12 15:10:44 kulupler ADDRCONF(NETDEV_UP): eth0: link is not ready
The connection never comes either after a network service restart, nor ifconfig eth0 up/down etc... The only solution is to restart, but after ~5 min. it fails again.
So, as a solution, I just downgraded the kernel to 2.6.19.1-1 again.

The AirPort Extreme base station (AEBS) is putting your PowerBook on a separate subnet. To solve the problem, configure the AEBS so that it does not distribute IP addresses.

WRV200 DDNS-Update fails at PPTP Connection

Hello!
I'm using the WRV200 Router (1.0.39) with an ADSL-Modem (Thomson) to connect to an Austrian ISP. So i have to use the PPTP-Connection to "dial in".
When i'm using this setting DDNS-Update via dyndns.org fails. The Status always says "diasabled". (The Account-Settings are checked)
A second WRV200 at another location uses a solid WAN-IP. This Router doesn't have any Problems with DDNS.
How can i solve this Problem?
Can you explain me the difference between normal and ETSI-Firmware?
Best regards
Mosquito

Hello Mr. Mosquito; the best advise that I can give you at this time is to follow this steps then retry to establish your connection,
-- factory default your router
--Down and uplaod the latest firmware into you router
--Manually reconfigure your router-----( DO NOT UPLOAD THE OLD CONFIGURATION)
-- Do a port forwarding with the server's LAN ip address under the port forwading tab in your router
Note:don't forget to create your account in your server before establishing any PPTP connection. If this does not work please contact us at 1866-606-1866 US/Canada.

IPhone stolen, how to I break their connection to my Apple id?

My phone was stolen approx a year ago, and about 2 weeks ago, new contacts started showing up in my phone (all of them Sri Lankan, as I've now found out), as well as months and months of new photos taken by the phone new owner appearing in my photostream.
I know I am not getting the phone back, and have long since replaced the stolen one, but this contact and photostream stuff is annoying! Is there a way to break this connection between my old phone and my contacts/photostream?
Many thanks in advance

Yes, reset your Apple ID password.
Apple ID: Changing your password

Urgent: Break RFC Connection

Hi,
How do I break / disable a RFC connection. Currently, my remote function works fine and data is also fetched. However I want to break the connection and test the program, for getting the appropriate error msg...how do i do this??

Hi vijay,
1. I don't think we can control this thru abap code.
regards,
amit m.

RV110W drops PPTP connections from a Windows client (MS CHAP v2 and MPPE)

This might be a tough problem to diagnose. I am trying to setup an RV100W for an office gateway with VPN access using PPTP. The office is located in another state, so I'm trying to do a "dry run" from home by setting up the RV110W on the local network. That is, my home network is 192.168.0.0 and I have assigned the RV110W a static IP address of 192.168.0.120 on its WAN side and a DHCP NAT internal network of 192.168.1.0. Its LAN IP is 192.168.1.2 (because of legacy limitations, the 192.168.1.1 address will be reserved for another host on the actual office network) and I set up the PPTP server on 192.168.1.3 and clients in the 192.168.1.20 to 24 range. I have enabled MPPE encryption and NetBIOS over VPN (rather important to have).
At first, I couldn't login at all. I had an underscore (_) in the user names (of which I have setup all five) and after I changed that, I was able to connect from a Windows 7 x64 host on the home LAN (192.168.0.132). I don't know if that was the problem as I got disconnected and reconnecting was a hit-or-miss - sometimes it would work, sometimes - it wouldn't. Below is the log from the session, showing the reasons for the disconnection. When I try to connect and it gets rejected, otherwise, the reason is the same: protocol not available.
But, first - here's the kicker. I had the exact same experience earlier with a DD-WRT router. I thought the problem lied with the amateurish firmware and that's why I decided to get the Cisco, but it seems like this might not be the problem, after all. Here is that discussion for full details: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=149951&highlight= (to see all of the attached images and logs, you'll need an account). Briefly, with the same setup, I can establish a stable VPN connection from four Windows XP clients and one Windows 7 client, but I get the problems with two other Windows 7 clients. The Win7 clients that give me trouble can connect just fine to other PPTP VPN servers (with the built-in Microsoft PPTP client) and all three Win7 machines are clones of each other (only the hardware is different). No software firewalls, anti-virus/malware, user-permission limitations (e.g., UAC), or anything that could hamper the connections, are present on either machine.
I don't see how the fact that the RV110W is on a LAN and not exposed to the Internet on its WAN side could cause any trouble, but even then - why some clients work fine and others - not? I would appreciate any help with this issue.
Kamen
This is the log from the session, showing the connection of the VPN client and then, not two minutes later, the disconnection.
2012-02-22 21:44:40 RV110W daemon.info pptpd[4582]: CTRL: Client 192.168.0.132 control connection started
2012-02-22 21:44:40 RV110W daemon.info pptpd[4582]: CTRL: Starting call (launching pppd, opening GRE)
2012-02-22 21:44:40 RV110W daemon.notice pppd[4583]: pppd 2.4.5 started by (unknown), uid 0
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: using channel 2
2012-02-22 21:44:40 RV110W daemon.info pppd[4583]: Using interface ppp0
2012-02-22 21:44:40 RV110W daemon.notice pppd[4583]: Connect: ppp0 <--> /dev/pts/0
2012-02-22 21:44:40 RV110W daemon.warning pppd[4583]: Warning - secret file /tmp/ppp/pap-secrets has world and/or group access
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [LCP ConfReq id=0x1 <auth chap MS-v2> <magic 0x4269dad6>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP ConfReq id=0x0 <mru 1400> <magic 0x5eec49d5> <pcomp> <accomp> <callback CBCP>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [LCP ConfRej id=0x0 <pcomp> <accomp> <callback CBCP>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP ConfAck id=0x1 <auth chap MS-v2> <magic 0x4269dad6>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP ConfReq id=0x1 <mru 1400> <magic 0x5eec49d5>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [LCP ConfAck id=0x1 <mru 1400> <magic 0x5eec49d5>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [LCP EchoReq id=0x0 magic=0x4269dad6]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CHAP Challenge id=0xfb <454ee20916a665999fdaa66778e1c4c5>, name = \"RV110W\"]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP Ident id=0x2 magic=0x5eec49d5 \"MSRASV5.20\"]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP Ident id=0x3 magic=0x5eec49d5 \"MSRAS-0-SOFTWAREONE64\"]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP Ident id=0x4 magic=0x5eec49d5 \"H\\37777777772\\37777777612\\37777777633F\\177\\37777777752J\\37777777640[\\377777776451\\37777777610\\\\Ob\"]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [LCP EchoRep id=0x0 magic=0x5eec49d5]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [CHAP Response id=0xfb <2aeb8dac876cbec7c23036952cfc270c00000000000000006f4cafa17228047ac82f26e47ae69eda8fe8650d5866e44b00>, name = \"sakor001\"]
2012-02-22 21:44:40 RV110W daemon.warning pppd[4583]: Warning - secret file /tmp/ppp/chap-secrets has world and/or group access
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CHAP Success id=0xfb \"S=ACBA0BE9B8A98DDB757B234A1C69E9508DE169DE M=Access granted\"]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/auth-up started (pid 4587)
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CCP ConfReq id=0x1 <mppe +H -M +S +L -D -C>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/auth-up finished (pid 4587), status = 0x16
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [CCP ConfReq id=0x5 <mppe +H -M +S -L -D -C>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CCP ConfAck id=0x5 <mppe +H -M +S -L -D -C>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfReq id=0x6 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-wins 0.0.0.0> <ms-dns2 0.0.0.0> <ms-wins 0.0.0.0>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [IPCP TermAck id=0x6]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [CCP ConfNak id=0x1 <mppe +H -M +S -L -D -C>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [CCP ConfReq id=0x2 <mppe +H -M +S -L -D -C>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [CCP ConfAck id=0x2 <mppe +H -M +S -L -D -C>]
2012-02-22 21:44:40 RV110W daemon.notice pppd[4583]: MPPE 128-bit stateless compression enabled
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: sent [IPCP ConfReq id=0x1 <addr 192.168.1.3>]
2012-02-22 21:44:40 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfAck id=0x1 <addr 192.168.1.3>]
2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfReq id=0x7 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-wins 0.0.0.0> <ms-dns2 0.0.0.0> <ms-wins 0.0.0.0>]
2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: sent [IPCP ConfRej id=0x7 <ms-wins 0.0.0.0> <ms-wins 0.0.0.0>]
2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfReq id=0x8 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: sent [IPCP ConfNak id=0x8 <addr 192.168.1.20> <ms-dns1 216.165.129.157> <ms-dns2 216.170.153.146>]
2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: rcvd [IPCP ConfReq id=0x9 <addr 192.168.1.20> <ms-dns1 216.165.129.157> <ms-dns2 216.170.153.146>]
2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: sent [IPCP ConfAck id=0x9 <addr 192.168.1.20> <ms-dns1 216.165.129.157> <ms-dns2 216.170.153.146>]
2012-02-22 21:44:42 RV110W daemon.notice pppd[4583]: local IP address 192.168.1.3
2012-02-22 21:44:42 RV110W daemon.notice pppd[4583]: remote IP address 192.168.1.20
2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/ip-up started (pid 4661)
2012-02-22 21:44:42 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/ip-up finished (pid 4661), status = 0x0
2012-02-22 21:44:42 RV110W user.debug syslog: Nbsrelay start (pid= 4678)
2012-02-22 21:46:10 RV110W daemon.notice pppd[4583]: Modem hangup
2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/auth-down started (pid 4858)
2012-02-22 21:46:10 RV110W daemon.info pppd[4583]: Connect time 1.5 minutes.
2012-02-22 21:46:10 RV110W daemon.info pppd[4583]: Sent 10404 bytes, received 17264 bytes.
2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/ip-down started (pid 4861)
2012-02-22 21:46:10 RV110W daemon.err pppd[4583]: MPPE disabled
2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: sent [LCP TermReq id=0x2 \"MPPE disabled\"]
2012-02-22 21:46:10 RV110W daemon.notice pppd[4583]: Connection terminated.
2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/auth-down finished (pid 4858), status = 0x16
2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Waiting for 1 child processes...
2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: script /tmp/ppp/ip-down, pid 4861
2012-02-22 21:46:10 RV110W daemon.debug pppd[4583]: Script /tmp/ppp/ip-down finished (pid 4861), status = 0x0
2012-02-22 21:46:10 RV110W daemon.info pppd[4583]: Exit.
2012-02-22 21:46:10 RV110W daemon.err pptpd[4582]: GRE: read(fd=11,buffer=449be4,len=8260) from network failed: status = -1 error = Protocol not available
2012-02-22 21:46:10 RV110W daemon.err pptpd[4582]: CTRL: GRE read or PTY write failed (gre,pty)=(11,10)
2012-02-22 21:46:10 RV110W daemon.debug pptpd[4582]: CTRL: Reaping child PPP[4583]
2012-02-22 21:46:10 RV110W daemon.info pptpd[4582]: CTRL: Client 192.168.0.132 control connection finished

Update: things are getting even weirder. In short - it seems to be working now (on the next day) without anything changing. First thing I did was just try another desperate tweak - I disabled the LCP extensions on the Windows client, which I've done before. It connected and stayed that way. Then, I reverted that setting back to exactly how it was before and connected again - no problems: it stayed connected for an hour (before I disconnected so I can connect to the real VPN), I could access a test-PC on the private network (a single machine just for the test) and do different tasks (resolve host names, browse UNC paths, copy files, Remote Desktop to it, etc.)
I hate it when things happen, for which there is no explanation. I couldn't be confident sending this to the main office to replace the existing router (hardware) and VPN server (implemented in software on a Windows 2003 server). Any thoughts?
Kamen
P.S. I'm attaching the logs from the successful session in case someone wants to compare them, but they seems quite identical (some different ConfAck / ConfNak sequences, but that doesn't seem to make much difference).
2012-02-23 10:01:26 RV110W daemon.info pptpd[944]: CTRL: Client 192.168.0.132 control connection started
2012-02-23 10:01:26 RV110W daemon.info pptpd[944]: CTRL: Starting call (launching pppd, opening GRE)
2012-02-23 10:01:26 RV110W daemon.notice pppd[946]: pppd 2.4.5 started by (unknown), uid 0
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: using channel 5
2012-02-23 10:01:26 RV110W daemon.info pppd[946]: Using interface ppp0
2012-02-23 10:01:26 RV110W daemon.notice pppd[946]: Connect: ppp0 <--> /dev/pts/0
2012-02-23 10:01:26 RV110W daemon.warning pppd[946]: Warning - secret file /tmp/ppp/pap-secrets has world and/or group access
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [LCP ConfReq id=0x1 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP ConfReq id=0x0 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [LCP ConfRej id=0x0 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP ConfAck id=0x1 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP ConfReq id=0x1 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [LCP ConfAck id=0x1 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [LCP EchoReq id=0x0 magic=0x11372b0b]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CHAP Challenge id=0x66 <74f93b7b6de315aaaac930f984c219e4>, name = \"RV110W\"]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP Ident id=0x2 magic=0x67c80cba \"MSRASV5.20\"]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP Ident id=0x3 magic=0x67c80cba \"MSRAS-0-SOFTWAREONE64\"]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP Ident id=0x4 magic=0x67c80cba \"
\\37777777675\\027\\37777777665\\004\\37777777635\\37777777677@H\\37777777633~\\37777777775\\021\\tFQ(\
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [LCP EchoRep id=0x0 magic=0x67c80cba]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CHAP Response id=0x66 <2f0330cb61ba1c8e29324410e0df24d3000000000000000025d1ef07d4cd82beaa93fe36ccc1e863b2652087eb02c39400>, name = \"sakor001\"]
2012-02-23 10:01:26 RV110W daemon.warning pppd[946]: Warning - secret file /tmp/ppp/chap-secrets has world and/or group access
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CHAP Success id=0x66 \"S=9A5FB4C8B7C633FD6DEB868E150D0511BD93E0B4 M=Access granted\"]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: Script /tmp/ppp/auth-up started (pid 949)
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CCP ConfReq id=0x1 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: Script /tmp/ppp/auth-up finished (pid 949), status = 0x16
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CCP ConfReq id=0x5 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CCP ConfNak id=0x5 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfReq id=0x6 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [IPCP TermAck id=0x6]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CCP ConfNak id=0x1 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CCP ConfReq id=0x2 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CCP ConfReq id=0x7 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [CCP ConfAck id=0x7 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [CCP ConfAck id=0x2 ]
2012-02-23 10:01:26 RV110W daemon.notice pppd[946]: MPPE 128-bit stateless compression enabled
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: sent [IPCP ConfReq id=0x1 ]
2012-02-23 10:01:26 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfAck id=0x1 ]
2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfReq id=0x8 ]
2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: sent [IPCP ConfRej id=0x8 ]
2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfReq id=0x9 ]
2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: sent [IPCP ConfNak id=0x9 ]
2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: rcvd [IPCP ConfReq id=0xa ]
2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: sent [IPCP ConfAck id=0xa ]
2012-02-23 10:01:28 RV110W daemon.notice pppd[946]: local IP address 192.168.1.3
2012-02-23 10:01:28 RV110W daemon.notice pppd[946]: remote IP address 192.168.1.20
2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: Script /tmp/ppp/ip-up started (pid 1028)
2012-02-23 10:01:28 RV110W daemon.debug pppd[946]: Script /tmp/ppp/ip-up finished (pid 1028), status = 0x0
2012-02-23 10:01:28 RV110W user.debug syslog: Nbsrelay start (pid= 1040)
2012-02-23 10:17:56 RV110W daemon.err pptpd[944]: GRE: Bad checksum from pppd.
2012-02-23 10:31:51 RV110W daemon.info udhcpd[807]: received INFORM from 00:13:46:E6:D3:FA
2012-02-23 10:48:20 RV110W daemon.info httpd[376]: Administrator session timeout.
2012-02-23 10:48:27 RV110W daemon.info httpd[376]: Administrator logined from 192.168.0.132
2012-02-23 10:52:50 RV110W daemon.info udhcpd[807]: received INFORM from 00:26:F2:B7:49:42
2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: rcvd [LCP TermReq id=0xb \"g\\37777777710\\014\\37777777672\\000<
\\37777777715t\\000\\000\\000\\000\
2012-02-23 10:58:49 RV110W daemon.info pppd[946]: LCP terminated by peer (gM-H^LM-:^@
2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Script /tmp/ppp/auth-down started (pid 6011)
2012-02-23 10:58:49 RV110W daemon.info pppd[946]: Connect time 57.4 minutes.
2012-02-23 10:58:49 RV110W daemon.info pppd[946]: Sent 272072987 bytes, received 6264878 bytes.
2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Script /tmp/ppp/ip-down started (pid 6015)
2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: sent [LCP TermAck id=0xb]
2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Script /tmp/ppp/auth-down finished (pid 6011), status = 0x16
2012-02-23 10:58:49 RV110W daemon.notice pppd[946]: Modem hangup
2012-02-23 10:58:49 RV110W daemon.notice pppd[946]: Connection terminated.
2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Waiting for 1 child processes...
2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: script /tmp/ppp/ip-down, pid 6015
2012-02-23 10:58:49 RV110W daemon.debug pppd[946]: Script /tmp/ppp/ip-down finished (pid 6015), status = 0x0
2012-02-23 10:58:49 RV110W daemon.info pppd[946]: Exit.
2012-02-23 10:58:49 RV110W daemon.debug pptpd[944]: CTRL: Reaping child PPP[946]
2012-02-23 10:58:49 RV110W daemon.info pptpd[944]: CTRL: Client 192.168.0.132 control connection finished

RV016 and PPTP connections logging

Hello. I have been using RV0's for quite a few years now, one thing that has bothered me is I have never been able to find or see any logging of actual users utilizing pptp vpn tunnels and when they initiate and close their tunnel connections. I am unable to see this information via the rvo gui log as well as in my syslog it dumps out to. Does the rv0 simply not provide this logging? If so why not? It seems like such a basic feature I am surprised if it is incapabile or unsupported. Thank you.

wbtadmin1,
I am not sure if the logging is simply not supported or if there is a hardware/software limitation. I know that I have had other customers ask about this in the past.
To make a feature request, please open a case: www.cisco.com/go/sbsc
It is possible that the feature will be added in a future firmware release.
- Marty

4.1.5B Breaks PPTP connection

Similar Messages

Maybe you are looking for