4500X command parser bug for monitor capture

I have had a question about wireshark support on the 4500X switches. I thought there were some capabilities missing from my 4500X-24 running 3.5.2E but as I was entering my question here I realized what the problem is. I thought capabilities were missing because the question mark doesn't doesn't display all the options:
Switch#show monitor capture ?
file Display captured file
Switch#show monitor capture mycap ?
% Unrecognized command
But it just seems to be a parser bug because it does actually accept and execute commands as documented:
Switch#show monitor capture mycap parameter
monitor capture mycap interface Vlan11 both
monitor capture mycap interface TenGigabitEthernet1/1/7 in
monitor capture mycap match ipv4 any any
monitor capture mycap file location bootflash:mycap.pcap buffer-size 1
monitor capture mycap limit packets 100 duration 60
I just thought I would pass this along.
-Jeff

What was the issue and how did you solve it?
-Deepak

Similar Messages

Monitor Capture for IPv6

Trying to capture IPv6 BGP hello traffic with monitor capture feature without success.
With the monitor capture for IPv6 traffic active and running; If I traceroute (IPv6) from this same router I do see the IPv6 traceroute traffic but NEVER IPv6 BGP hellos.
NOTE:
IPv6 traceroute traffic is not shown in the below output because I already cleared the V6BUFF buffer before running the show command.
My setup:
monitor capture buffer V6BUFF size 512 max-size 128 linear
monitor capture point ipv6 cef V6PT mfr0.1 both
monitor capture point associate V6PT V6BUFF
monitor capture point start V6PT
Troubleshooting
After disassociating monitor capture point V4PT here are the results:
1941-WAN3#sh mon cap buff all par
Capture buffer V6BUFF (linear buffer)
Buffer Size : 524288 bytes, Max Element Size : 128 bytes, Packets : 0
Allow-nth-pak : 0, Duration : 0 (seconds), Max packets : 0, pps : 0
Associated Capture Points:
Name : V6PT, Status : Active
Configuration:
monitor capture buffer V6BUFF size 512 max-size 128 linear
monitor capture point associate V6PT V6BUFF
Capture buffer V4BUFF (linear buffer)
Buffer Size : 524288 bytes, Max Element Size : 128 bytes, Packets : 125
Allow-nth-pak : 0, Duration : 0 (seconds), Max packets : 0, pps : 0
Associated Capture Points:
Name : V4PT, Status : Inactive <--- I already disassociated this one
Configuration:
monitor capture buffer V4BUFF size 512 max-size 128 linear
monitor capture point associate V4PT V4BUFF
Regards
Frank

What was the issue and how did you solve it?
-Deepak

[svn:fx-trunk] 11601: Integrating Min' s recent fixes to FXGUtils for a group of attribute parsing bugs and clarification of error messages .

Revision: 11601
Author:   [email protected]
Date:     2009-11-09 22:00:50 -0800 (Mon, 09 Nov 2009)
Log Message:
Integrating Min's recent fixes to FXGUtils for a group of attribute parsing bugs and clarification of error messages.
QE notes: Please confirm test cases.
Doc notes: N/A
Bugs:
SDK-22982 - FXG compiler fails on percentage lineheight inside formatted text content
SDK-24093 - If a
tag has children, you do not get a compile error.
SDK-24092 - You get a compile error if you set justificationStyle="prioritizeLeastAdjustment"
SDK-24097 - Setting an invalid verticalAlign style on RichText has a typo in the error message
Reviewer: Min
Tests run: Checkintests, Bug test cases
Is noteworthy for integration: No
Ticket Links:
    http://bugs.adobe.com/jira/browse/SDK-22982
    http://bugs.adobe.com/jira/browse/SDK-24093
    http://bugs.adobe.com/jira/browse/SDK-24092
    http://bugs.adobe.com/jira/browse/SDK-24097
Modified Paths:
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/fxg/FXGException_en.properties
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/RichTextNode.java
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/richtext/AbstractRich BlockTextNode.java
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/richtext/AbstractRich TextLeafNode.java
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/richtext/AbstractRich TextNode.java
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/richtext/BRNode.java
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/richtext/ImgNode.java
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/richtext/TabNode.java
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/richtext/TextHelper.j ava
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/dom/text/AbstractCharacte rTextNode.java
    flex/sdk/trunk/modules/fxgutils/src/java/com/adobe/internal/fxg/sax/FXGSAXScanner.java

Dear Pallavi,
Very useful post!
I am looking for similar accelerators for
Software Inventory Accelerator
Hardware Inventory Accelerator
Interfaces Inventory
Customization Assessment Accelerator
Sizing Tool
Which helps us to come up with the relevant Bill of Matetials for every area mentioned above, and the ones which I dont know...
Request help on such accelerators... Any clues?
Any reply, help is highly appreciated.
Regards
Manish Madhav

[Patch 정보] TRACKING BUG FOR CUMULATIVE MLR#6 ON TOP OF BPEL PM 10.1.3.3.1

최근에 출시된 BPEL PM 10.1.3.3.1의 통합패치입니다.
아래는 readme.txt에 포함된 patch list입니다.
# WARNING: Failure to carefully read and understand these requirements may
# result in your applying a patch that can cause your Oracle Server to
# malfunction, including interruption of service and/or loss of data.
# If you do not meet all of the following requirements, please log an
# iTAR, so that an Oracle Support Analyst may review your situation. The
# Oracle analyst will help you determine if this patch is suitable for you
# to apply to your system. We recommend that you avoid applying any
# temporary patch unless directed by an Oracle Support Analyst who has
# reviewed your system and determined that it is applicable.
# Requirements:
# - You must have located this patch via a Bug Database entry
# and have the exact symptoms described in the bug entry.
# - Your system configuration (Oracle Server version and patch
# level, OS Version) must exactly match those in the bug
# database entry - You must have NO OTHER PATCHES installed on
# your Oracle Server since the latest patch set (or base release
# x.y.z if you have no patch sets installed).
# - [Oracle 9.0.4.1 & above] You must have Perl 5.00503 (or later)
# installed under the ORACLE_HOME, or elsewhere within the host
# environment.
# Refer to the following link for details on Perl and OPatch:
# http://metalink.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=189489.1
# If you do NOT meet these requirements, or are not certain that you meet
# these requirements, please log an iTAR requesting assistance with this
# patch and Support will make a determination about whether you should
# apply this patch.
# 10.1.3.3.1 Bundle Patch 6823628
# DATE: March 14, 2008
# Platform Patch for : Generic
# Product Version # : 10.1.3.3.1
# Product Patched : Oracle(R) SOA
# Bugs Fixed by 10.1.3.3.1 Initial patch 6492514 :
# Bug 5473225 - PATCH01GENESIS HOT UNABLE TO CATCH AN EXCEPTION DURING A
# TRANSFORM
# Bug 5699423 - PARTNERLINK PROPERTY THAT SET BPELXPROPERTY FUNCTION DOESN'T
# WORK
# Bug 5848272 - STATEFUL WEBSERVICES DEMO ON OTN DOES NOT WORK 10.1.3.1
# Bug 5872799 - ANT DEPLOY BPEL TEST FAILS/RUNS ON DEFAULT DOMAIN NOT
# SPECIFIED TARGET DOMAIN
# Bug 5883401 - ALLOW A WAY TO CREATE EMPTY NODES - AND USE FOR REQUIRED
# NODES
# Bug 5919412 - SAMPLE DEMO BPEL PROCESSES MIMESERVICE MIMEREQUESTER AXIS
# JAVA EXAMPLE ERROR
# Bug 5924483 - ESB SHOULD SUPPORT SOAP EDNPOINT LOCATION DYNAMIC UDDI LOOKUP
# Bug 5926809 - ORAPARSEESCAPEDXML XPATH EXPRESSION FAILED TO EXECUTE
# FOTY0001 TYPE ERROR
# Bug 5937320 - STRANGE BEHAVIOUR CALLING FROM BPEL TO BPEL GETTING
# NULLPOINTEREXCEPTION.
# Bug 5944641 - BPA BLUEPRINT NOT AVAIALBLE IN JDEVELOPER
# Bug 5945059 - JAVA.LANG.NULLPOINTEREXCEPTION SENDING EMAILS WITH PAYLOADS
# LARGER THAT 1MB
# Bug 5962677 - WS RESPONSE IS EMPTY SOAP BODY IN ONE-WAY CALL
# Bug 5963425 - WHEN THE OUTCOMES FOR A HT CHANGED & IMPORTED - UPDATE
# CONNECTION ROLES IN BPEL
# Bug 5964097 - AQ ADAPTER DEPLOYMENT CAUSES OPMN TO PERFORM A FORCEFUL
# SHUTDOWN IN SOA
# Bug 5971534 - CANNOT GRANT USER TASK VIEWS TO GROUPS, ONLY TO USERS.
# Bug 5989367 - REFER TO SR 6252219.993 BPEL 10.1.3 ONLY COPIES IN ASSIGN,
# IN 10.1.2 IT CREATES
# Bug 5989527 - ENHANCEMENT WARNING SHOULD BE GIVEN UPON UPLOAD IF BPEL
# PROCESS IS OPEN IN ARIS
# Bug 5997936 - ESB FAULT DOES NOT GET PROPAGATED TO BPEL
# Bug 6000575 - PERF NEED ESB PURGE SCRIPT TO PURGE BY DATE AND PROCESS
# Bug 6001796 - POSTING OF DATE RECEIVED FROM XML GATEWAY TO BPEL FAILED IN
# ESB
# Bug 6005407 - BPEL PROCESS DOESN'T PROPOGATE FAULT THROWN BY BPEL
# SUB-PROCESS
# Bug 6017846 - MIMETYPE OF EMAIL NOTIFICATION IS NOT SET THROUGH HUMAN TASK
# Bug 6027734 - DECISION SERVICE IMPORT - LOCATING DECISION SERVICE IN .DECS
# FILE IMPROPER
# Bug 6028985 - EXCEEDED MAXIMUM NUMBER OF SUBSCRIBERS FOR QUEUE
# ORAESB.ESB_CONTROL
# Bug 6041508 - CREATING/UPDATING DVM CAUSE EXCEPTION
# Bug 6053708 - FTP ADAPTER DOES NOT SUPPORT ENCRYPTED PASSWORD IN
# OC4J-RA.XML
# Bug 6054034 - INDEX4,INDEX5 AND INDEX6 CANNOT BE USED IN BPEL CONSOLE
# Bug 6068801 - BACKPORT OF BPEL ON WEBLOGIC - VERSION 10.1.3.3
# Bug 6070991 - HT EXPORT DOES NOT EXPORT PARAMETERS, ALLOW PARTICIPANTS TO
# INVITE OTHERS
# Bug 6071001 - WSIF HTTP BINDING NOT WORKING FROM ESB
# Bug 6073311 - STRESS SCOPE NOT FOUND ON CALLBACK - WRONG (DUPE)
# SUBSCRIPTION IN TABLE
# Bug 6081070 - JMS ADAPTER REJECTION HANDLER CREATE 0 BYTE FILES
# Bug 6083419 - DECISION SERVICE SCOPE NEED TO HAVE A SPECIAL INDICATOR
# Bug 6085799 - HUMAN TASK ADDED IN SCOPE IN JDEV IS NOT UPDATED TO BPA
# SERVER
# Bug 6085933 - EXPORT AND EXPLORE SHOULD USE USER LANGUAGE AND NOT ENGLISH
# ALWAYS
# Bug 6086281 - STRING INDEX OUT OF RANGE ERROR FOR COBOL COPYBOOK WITH PIC
# CLAUSE HAVING S
# Bug 6086453 - DOMAINS CREATED IN A CLUSTER GETS NOT PROPAGATED TO NEW OR
# EXISTING NODES
# Bug 6087484 - MULTIPLE HEADER SETTING CAUSES ESB EXCEPTION
# Bug 6087645 - ESB SHOULD ALLOW USER PICK RUNTIME PROTOCOL (HTTP/HTTPS)
# Bug 6110231 - TRANSLATION NOT BASED ON MQ CCSID CHARSET
# Bug 6120226 - BPEL IS NOT SETTING THE APPS CONTEXT CORRECTLY
# Bug 6120323 - COMPLETIONPERSISTPOLICY ON DOMAIN LEVEL HAS DISAPPEARED
# Bug 6125184 - ESB JMS SESSION ROLLBACK ORACLE.JMS.AQJMSEXCEPTION
# Bug 6127824 - [AIA2.0] CURRENT XREF IMPLEMENTATION IS MISSING REQUIRED
# INDEXES ON XREF SCHEMA
# Bug 6128247 - HTTPCONNECTOR POST() METHOD SHOULD RAISE EXCEPTION FOR ALL
# STATUS CODES EXCEPT 2
# Bug 6131159 - ENABLE USERS TO CHOOSE XSD WHEN CREATING A BPEL PROCESS FROM
# BLUE PRINT
# Bug 6132141 - PROCESS_DEFAULT TABLE STILL CONTAINS INFORMATION FROM
# UNDEPLOYED PROCESSES
# Bug 6133190 - ENABLING ESB CONSOLE HTTP/S IS MAKING THE CONSOLE TO COME UP
# BLANK.
# Bug 6139681 - BPEL WSDL LINK IN CLUSTERED RUNTIME POINTS TO A SINGLE NODE
# Bug 6141259 - BASICHEADERS NOT PUTTING WWW-AUTHENTICATE HEADERS FOR HTTP
# BINDING IN BPEL
# Bug 6148021 - BPEL NATIVE SCHEMA FOR COBOL COPYBOOK WITH IMPLIED DECIMAL
# LOSES DIGIT IN OUTPUT
# Bug 6149672 - XOR DATA - CONDITION EXPRESSION SPECIFICATION IS NOT
# INTUITIVE IN BPMN MODELS
# Bug 6152830 - LOSING CONDITIONAL EXPRESSIONS CREATED IN JDEV UPON MERGE
# Bug 6158128 - BASICHEADERS NOT PUTTING WWW-AUTHENTICATE HEADERS FOR HTTP
# BINDING
# Bug 6166991 - WHEN STARTING SOA SUITE,, PROCESSES FAIL DUE TO UNDEFINED
# WSDL
# Bug 6168226 - LOCATION-RESOLVER EXCEPTION THROWN IN OPMN LOGS
# Bug 6187883 - CHANGES FOR BPEL RELEASE ON JBOSS- VERSION 10.1.3.3
# Bug 6206148 - [AIA2.0] NEW FUNCTION REQUEST, XREFLOOKUPPOPULATEDCOLUMNS()
# Bug 6210481 - BPEL PROCESS WORKS INCORRECTLY WHEN AN ACTIVITY HAS MULTIPLE
# TRANSITIONCONDITION
# Bug 6240028 - WEBSERVICE THAT DOES NOT CHALLENGE FOR BASIC CREDENTIALS
# CANNOT BE INVOKED
# Bug 6257116 - MULTIPLE HEADER SETTING CAUSES ESB EXCEPTION
# Bug 6258925 - MESSAGE RECEIVED BY THE TARGET ENDPOINT VIA HTTP POST IS
# MISSING THE XML HEADER
# Bug 6259686 - TOO MANY UNNECESSARY WORKFLOW E-MAIL NOTIFICATIONS GENERATED
# Bug 6267726 - 10.1.3.3 ORACLE APPLICATIONS ADAPTER - NOT ABLE TO CAPTURE
# BUSINESS EVENT
# Bug 6272427 - WEBSPHERE BPEL FAILS FOR DATA RETRIEVAL OF SIZE 500+ KB
# Bug 6276995 - MERGE SCOPE NAME IS NOT UPDATED WHEN CHANGED IN THE SERVER
# Bug 6280570 - XPATH EXPRESSION ERROR IN MEDIATOR FOR ASSIGNING USER-DEFINED
# CONTEXT VALUES
# Bug 6282339 - RETRYCOUNT DOES NOT WORK PROPERLY
# Bug 6311039 - ONE RECORD IS INSERTED TO SYNC_STORE IF
# COMPLETIONPERSISTPOLICY SET TO FAULTED
# Bug 6311809 - [AIA2.0] NON-RETRYABLE ERRORS ARE NOT POSTED ON ESB_ERROR
# TOPIC
# Bug 6314784 - THE PRIORITY DEFINED IN THE BPA SUITE IS NOT TRANSFERRED TO
# THE JDEV CORRECTLY
# Bug 6314982 - THREADPOOL RACE CONDITION IN ADAPTER INITIALIZATION MESSAGES
# NOT PROCESSED
# Bug 6315104 - (SET)CLASSNAME MISSING IN TSENSOR JAXB OBJECTS
# Bug 6316554 - CONSUME FUNCTIONALITY OF JMS ADAPTER FOR BEA WEBLOGIC DOES
# NOT WORK
# Bug 6316950 - FILEADAPTER HARPER ENHANCEMENTS SYNC WRITE AND CHUNKED
# INTERACTION SPEC
# Bug 6317398 - THE ICON FOR COMPUTING DIFFERENCE IS MISSING IN JDEV REFRESH
# FROM SERVER DIALOG
# Bug 6320506 - IMPORT FAILS WHEN THERE IS AN UNNAMED CASE
# Bug 6321011 - CANNOT PROCESS 0 BYTE FILE USING FTP ADAPTER
# Bug 6325749 - TRACKING BUG FOR TRACKING ADDITIONAL CHANGES TO BUG #6032044
# Bug 6328584 - NEED A NEW XPATH EXPRESSION TO GET ATTACHMENT CONTENT VIA
# SOAP INVOKATION
# Bug 6333788 - COLLAPSING OF CONSECUTIVE ASSIGN TASKS BREAKS BAM SENSOR
# Bug 6335773 - BUILD.XML CONTAINS DO NOT EDIT .. - WHILE <CUSTOMIZE> TASK
# MUST BE IN <BPELC>
# Bug 6335805 - AQ ADAPTER OUTBOUND DOESN'T RECONNECT AFTER FAILURE
# Bug 6335822 - [AIA2.0] PSRPERFESB - RUNTIME DVM PERFORMANCE OVERHEAD IN ABS
# USE CASE
# Bug 6339126 - CHECKPOINT BPEL JAVA METHOD DOESN'T WORK IN BPEL 10.1.3.3
# Bug 6342899 - OUTLINECHANGE.XML NOT UPDATE WITH ACTIVITY FROM NEW BRANCH
# Bug 6343299 - ESB CONCRETE WSDL NAMESPACE SHOULD BE DIFFERENT FROM IMPORTED
# WSDL NAMESPACE
# Bug 6372741 - DEHYDRATION DATABASE KEEPS GROWING IN 10.1.3.3
# Bug 6401295 - NXSD SHOULD SUPPORT ESCAPING THE TERMINATED/QUOTED/SURROUNDED
# DELIMITERS
# Bug 6458691 - DIST DIRECTORY FOR 10.1.3.3.1 NEEDS UPDATE
# Bug 6461516 - BPEL CONSOLE CHANGES FOR DISPLAYING RELEASE 10.1.3.3.1
# Bug 6470742 - CHANGE THE VERSION NUMBER AND BUILD INFO IN ABOUT DIALOG IN
# ESB
# BUG ADDED IN MLR#1, 6671813 :
# Bug 6494921 - ORABPEL-02154 IF LONG DOMAIN AND SUITECASE NAMES IN USE
# BUGS ADDED IN MLR#2, 6671831 :
# Bug 6456519 - ERROR IN BPEL CONSOLE THREADS TAB:SERVLETEXCEPTION CANNOT GET
# DISPATCHER TRACE
# Bug 6354719 - WHICH JGROUP CONFIGURATION PARAMETER IMPACTS BPEL CLUSTER
# ACTIVITY
# Bug 6216169 - SCOPE NOT FOUND ERROR WHILE DELIVERING EXPIRATION MESSAGE OF
# ONALARM
# Bug 6395060 - ORA-01704 ON INSERTING A FAULTED INVOKE ACTIVITY_SENSOR
# Bug 6501312 - DEHYDRATION DATABASE KEEPS GROWING IN 10.1.3.3 #2
# Bug 6601020 - SEARCHBASE WHICH INCLUDES PARENTHESIS IN THE NAMES DOES NOT
# WORK
# Bug 6182023 - WAIT ACTIVITY FAILS TO CONTINUE IN CLUSTER WHEN PROCESSING
# NODE GOES DOWN
# BUGS ADDED IN MLR#3, 6723162 :
# Bug 6725374 - INSTANCE NOT FOUND IN DATASOURCE
# Bug 4964824 - TIMED OUT IF SET CORRELATIONSET INITIATE YES IN REPLY
# ACTIVITY
# Bug 6443218 - [AIA2.0]BPEL PROCESS THAT REPLIES A CAUGHT FAULT AND THEN
# RETHROWS IT IS STUCK
# Bug 6235180 - BPPEL XPATH FUNCTION XP20 CURRENT-DATETIME() IS RETURNING AN
# INCORRET TIME
# Bug 6011665 - BPEL RESTART CAUSES ORABPEL-08003 FAILED TO READ WSDL
# Bug 6731179 - INCREASED REQUESTS CAUSE OUTOFMEMORY ERRORS IN OC4J_SOA WHICH
# REQUIRES A RESTART
# Bug 6745591 - SYNC PROCESS <REPLY> FOLLOWED BY <THROW> CASE CAUSING
# OUTOFMEMORY ERRORS
# Bug 6396308 - UNABLE TO SEARCH FOR HUMAN TASK THAT INCLUDES TASK HISTORY
# FROM PREVIOUS TASK
# Bug 6455812 - DIRECT INVOCATION FROM ESB ROUTING SERVICE FAILS WHEN CALLED
# BPEL PROCESS
# Bug 6273370 - ESBLISTENERIMPL.ONFATALERROR GENERATING NPE ON CUSTOM ADAPTER
# Bug 6030243 - WORKFLOW NOTIFICATIONS FAILING WITHOUT BPELADMIN USER
# Bug 6473280 - INVOKING A .NET 3.0 SOAP SERVICE EXPOSED BY A ESB ENDPOINT
# GIVES A NPE
# BUGS ADDED IN MLR#4, 6748706 :
# Bug 6336442 - RESETTING ESB REPOSITORY DOES NOT CLEAR DB SLIDE REPOSITORY
# Bug 6316613 - MIDPROCESS ACTIVATION AGENT DOES NOT ACTIVATED FOR RETIRED
# BPEL PROCESS
# Bug 6368420 - SYSTEM IS NOT ASSIGNING TASK FOR REAPPROVAL AFTER REQUEST
# MORE INFO SUBMITTED
# Bug 6133670 - JDEV: UNABLE TO CREATE AN INTEGRATION SERVER CONNETION WHEN
# ESB IS ON HTTPS
# Bug 6681055 - TEXT ATTACHMENT CONTENT IS CORRUPTED
# Bug 6638648 - REQUEST HEADERS ARE NOT PASSED THROUGH TO THE OUTBOUND HEADER
# Bug 5521385 - [HA]PATCH01:ESB WILL LOSE TRACKING DATA WHEN JMS PROVIDER IS
# DOWN
# Bug 6759068 - WORKLIST APPLICATION PERFORMANCE DEGRADATION W/ SSL ENABLED
# FOR BPEL TO OVD
# BUGS ADDED IN MLR#5, 6782254 :
# Bug 6502310 - AUTOMATED RETRY ON FAILED INVOKE WITH CORRELATIONSET INIT
# FAILS
# Bug 6454795 - FAULT POLICY CHANGE NEEDS RESTART OF BPEL SERVER
# Bug 6732064 - FAILED TO READ WSDL ERROR ON THE CALLBACK ON RESTARTING BPEL
# OC4J CONTAINER
# Bug 6694313 - ZERO BYTE FILE WHEN REJECTEDMESSAGEHANDLERS FAILS
# Bug 6686528 - LINK IN APPLICATION.XML FILES CHANGED TO HARD LINKS WHEN MORE
# THAN 1 HT PRESENT
# Bug 6083024 - TEXT AND HTML DOC THAT RECEIVED AS ATTACHMENTS WERE EITHER
# BLANK OR GARBLED
# Bug 6638648 - REQUEST HEADERS ARE NOT PASSED THROUGH TO THE OUTBOUND HEADER
# Bug 6267726 - 10.1.3.3 ORACLE APPLICATIONS ADAPTER - NOT ABLE TO CAPTURE
# BUSINESS EVENT
# Bug 6774981 - NON-RETRYABLE ERRORS ARE NOT POSTED ON ESB_ERROR TOPIC
# Bug 6789177 - SFTP ADAPTER DOES NOT SUPPORT RENAMING FILES
# Bug 6809593 - BPEL UPGRADE TO 10.1.3.3.1 WITH ESB CALLS FAILS DUE TO
# CACHING OF PLNK - SERVICE
# BUGS ADDED IN MLR#6, 6823628 :
# Bug 6412909 - <BPELX:RENAME> DOES NOT ADD XMLNS DECLARATION AUTOMATICALLY
# Bug 6753116 - OUTPUT FROM HUMAN TASK IS NOT IS NOT CONSISTENT WITH
# SCHEMA
# ORDERING
# Bug 6832205 - BAD VERIFICATIONSERVICE PERFORMANCE IF LDAP SERVICE HAS HUGE
# DATA
# Bug 6189268 - CALLING BPEL PROCESS VIA SOAP FROM ESB FAILS WITH
# NAMENOTFOUNDEXCEPTION
# Bug 6834402 - JMS ADAPTER IMPROPERLY CASTS XAQUEUESESSION TO QUEUESESSION
# Bug 6073117 - TASK SERVICE DOESN'T RENDER THE TASK ACTIONS
# Bug 6054263 - REUSING SOAP WSDL IN RS CAUSES SOAP ACTION'S NS TO BE
# STRIPPED
# AWAY
# Bug 6489703 - ESB: NUMBER OF LISTENERS > 1 GIVES JMS EXCEPTION UNDER STRESS
# Bug 5679542 - FTP ADAPTER: COULD NOT PARSE TIME:
# JAVA.LANG.STRINGINDEXOUTOFBOUNDSEXCEPTION
# Bug 6770198 - AQ ACTIVATIONINSTANCES >1 DOESN'T WORK IN ESB
# Bug 6798779 - ESB ROUTING RULES CORRUPTED ON RE-REGISTERING WITH ROUTING
# ORDER
# IN WSDL CHANGED
# Bug 6617974 - BACKPORT REQUEST FOR MOVING FILES FUNCTION OF FTP ADAPTER
# Bug 6705707 - VALIDATION ON ESB CAN'T HANDLE NESTED SCHEMAS
# Bug 6414848 - FTP ADAPTER ARCHIVE FILENAME FOR BPEL IS BEING SCRAMBLED
# AFTER
# THE 10.1.3.3 UPGR
# Bug 5990764 - INFORMATION ARE LOST WHEN BPEL PROCESS IS POLLING FOR MAILS
# WITH
# ATTACHEMENTS
# Bug 6802070 - ORA-12899 SUBSCRIBER_ID/RES_SUBSCRIBER COLUMN SMALL FOR LONG
# DOMAIN AND PROCESS
# Bug 6753524 - WRONG SERVICE ENDPOINT OPEN WHEN TEST WEB SERVICE OF ESB
# Bug 6086434 - PROBLEM IN BPEL FILE ADAPTER WHILE READING A FIXED LENGTH
# FILE
# Bug 6823374 - BPEL 10.1.3.3.1 BAM SENSOR ACTION FAILS WITH BAM 11
# Bug 6819677 - HTTS STATUS 202 RETURNED INSTEAD OF SOAP FAULT
# Bug 6853301 - MQ ADAPTER REJECTED MESSAGES IS NOT REMOVED FROM THE RECOVERY
# QUEUE
# Bug 6847200 - 10.1.3.3.1 PATCH (#6748706) HAS STOPPED FTP ADAPTER POLLING
# IN
# SFTP MODE
# Bug 6895795 - AQ OUTBOUND DOESN'T WORK WITH MLR#6
업무에 참고하시기 바랍니다.

David,
You are right, theer are some changes incorporated in the latest MLR # 16 on the configurations files and on the dehydration store metrics(such as performance, fields,..).
However, I would not suggest to continue working on olite, even for Development/Test purposes as you might get stuck with strange errors...and the only solution would be to re-install SOA Suite if your olite gets corrupted. There might be ways to gets your olite back to position, but trust me..its not so simple.
Also, when you develop and stress test all your testcase scenarios in an TEST Adv installation, its simple to mimic the same in actual production box, as you exactly know its behavior.
So, go for a brand new SOA 10.1.3.4 MLR # 5 (or) 10.1.3.3.1 MLR # 16 SOA Suite Advanced installation with Oracle DB 10.2.0.3 as its dehydration store.
Hope this helps!
Cheers
Anirudh Pucha

OracleCommand Parsing Bug

I am using Oracle.DataAccess.dll v2.111.6.0 and have encountered a bug in OracleCommand's parsing algorithm.
This code should run properly:
using (var con = new Oracle.DataAccess.Client.OracleConnection(connString))
con.Open();
using (var c = con.CreateCommand())
c.CommandText = "SELECT 1 FROM dual WHERE ''=/**/'' and 1 = :p1";
c.BindByName = true;
var p = c.CreateParameter();
p.ParameterName = ":p1";
p.Value = 1;
c.Parameters.Add(p);
var r = c.ExecuteScalar();
Instead it throws an OracleException with the message "ORA-01008: not all variables bound".
With a little digging I found that the problem is that once the command parser in the OracleCommand class encounters the combination of characters - */' - it enters an invalid state which causes it to ignore any parameters defined afterwards and as a result the parameters are not sent to the oracle engine.
Is this bug known and, if so, is there a fix?

Hi Anthony,
I saw you're using Windows XP, so you can use the "patch" utility found in the GNU tools for Win32. You can download the "patch" tool here: http://sourceforge.net/project/showfiles.php?group_id=23617&package_id=32165
Download the patch that fixes the issue, http://www.oracle.com/technology/products/berkeley-db/xml/update/2.3.10/patch.2.3.10.2
The patch tool should be run like this to apply the patch:
BerkeleyDBXML_2.3.10_root_dir>"C:\Program Files\GnuWin32\bin\patch.exe" -p0 -i patch.2.3.10.2 --binary
Regards,
Andrei

How to change parsing schema for REST

Hi all,
I'm trying to test the new REST Webservice feature, but this leads to an error:
Using Apex 4.2.1.00.08, Listener 2.0.1.64.14.25 I set up a simple WebService (method: GET, format: JSON) which
querys a table.
When I try to test my webservice (using "Test" button) the following error is shown:
Request Path passes syntax validation
Mapping request to database pool: PoolMap [_poolName=apex, _regex=null, _workspaceIdentifier=null, _failed=false, _lastUpdate=-1, _template=null, _type=REGEX]
Applied database connection info
Attempting to process with PL/SQL Gateway
Not processed as PL/SQL Gateway request
Attempting to process as a RESTful Service
Determining if request can be dispatched as a Tenanted RESTful Service
Request path has one path segment, continuing processing
No Tenant Principal established yet, continuing processing
APEX_LISTENER pool exists, continuing processing
Matching tenant exists, continuing processing
modul/template/ matches: modul/template/ score: 0
Choosing: oracle.dbtools.rt.resource.templates.jdbc.JDBCResourceTemplateDispatcher as current candidate with score: Score [handle=JDBCURITemplate [scopeId=null, templateId=1019223475312614|5204902308237886, uriTemplate=modul/template/], score=0, scope=SecurityConfig [constraint=none, realm=NONE, logonConfig=LogonConfig [logonForm=null, logonFailed=null]], originsAllowed=[], corsEnabled=true]
Determining if request can be dispatched as a Tenanted RESTful Service
Request path has one path segment, continuing processing
Tenant Principal already established, cannot dispatch
Chose oracle.dbtools.rt.resource.templates.jdbc.JDBCResourceTemplateDispatcher as the final candidate with score: Score [handle=JDBCURITemplate [scopeId=null, templateId=1019223475312614|5204902308237886, uriTemplate=modul/template/], score=0, scope=SecurityConfig [constraint=none, realm=NONE, logonConfig=LogonConfig [logonForm=null, logonFailed=null]], originsAllowed=[], corsEnabled=true] for: GET modul/template/
Choosing: oracle.dbtools.rt.jdbc.entity.JDBCTenantDispatcher as current candidate with score: Score [handle=oracle.dbtools.rt.jdbc.entity.JDBCTenantDispatcher$TenantTarget@1537060, score=1, scope=SecurityConfig [constraint=none, realm=NONE, logonConfig=LogonConfig [logonForm=null, logonFailed=null]], originsAllowed=[], corsEnabled=true]
Chose oracle.dbtools.rt.jdbc.entity.JDBCTenantDispatcher as the final candidate with score: Score [handle=oracle.dbtools.rt.jdbc.entity.JDBCTenantDispatcher$TenantTarget@1537060, score=1, scope=SecurityConfig [constraint=none, realm=NONE, logonConfig=LogonConfig [logonForm=null, logonFailed=null]], originsAllowed=[], corsEnabled=true] for: GET prx/modul/template/
prx/modul/template/ is a public resource
modul/template/ is a public resource
Using generator: oracle.dbtools.rt.json.query.JSONQueryGenerator
Performing JDBC request as: POFFICE
Error during evaluation of resource template: ORA-00942: Tabelle oder View nicht vorhanden
I see what is going wrong: "Performing JDBC request as: POFFICE". JDBC is using a wrong schema ("POFFICE").
So, my question is, how to change the parsing schema for JDBC/WebService?
Thanks a lot,
Michael

jfle wrote:
Yes - this is the reason,
but is there a way to change or delete the first schema provisioned?See {message:id=3757162}
We have deleted the poffice assignment to the workspace, but the REST-service executes with poffice?Don't know could be a bug.
May be try exporting you restful webservice definition > Edit the export file in textpad/notepad and verify the parsing schema
You will see a block something like below, there just amend the p_parsing_schema to desired > and then import it back
wwv_flow_api.create_restful_module (
p_id => 7113266627142076447 + wwv_flow_api.g_id_offset
,p_name => 'oracle.example.vikram2'
,p_parsing_schema => 'APX'
,p_items_per_page => 25
,p_status => 'PUBLISHED'
);

Useful for monitoring HDV in Final Cut Pro?

Here is a new blackmagic card for HD. Seems like this could be a cheaper way to monitor my FCP timeline. I normally edit HDV shows either natively of as AIC compressed. But I have to monitor it through the "desktop cinema preview" feature which doesn't show interlacing. So I don't really see the true picture I'm editing. This new card would seem to allow me to monitor on a modern consumer TV with HDMI input.
To good to be true?? Probably. What does anyone think?
http://blackmagic-design.com/products/intensity/
Paul

It's made for capturing other than HDV directly from camera in a live situation... not tape. Once captured as something else, it can be used to send the HDMI to a consumer HD set. Once on tape though, it's HDV all the way. This thing is an odd duck piece of gear used for special setups.... it's not what you need.
What you need is a Matrox MXO, or capture card that will convert the HDV to uncompressed HD or SD for monitoring...
Jerry

Configure CBQoS for monitoring.

Hi, i want to configure CBQoS in a lot of 2960 switches (with snmp v1) for monitoring: jitter, delay and packets lost with PRTG software.
I not found documentation for understand CBQoS, but i see this doc:
http://www.cisco.com/en/US/docs/ios/ios_xe/qos/configuration/guide/cbqos_mib_xe.html
and when i put these commands:
1. enable
2. configure terminal
3. snmp-server ifindex persist
4. snmp mib persist [cbqos | v3mibs]
5. end
6. write mib-data
I can't do the step 4
Switch(config)#snmp mib ?
community-map     Community Mapping as per RFC-2576
notification-log Configure the Notification Log MIB
rep               Enable SNMP Resilient Ethernet Protocol options
target            target extention CLI from SNMP
PS: Or maybe is a simplest way to monitor QoS.
Thanks!

I realy sorry, i didn't realise for the IOS version. I'm replying myself:
Upgrade IOS:
c2960-lanbasek9-mz.122-55.SE8
to
c2960-lanbasek9-mz.150-2.SE4
Switch(config)#snmp mib ?
community-map     Community Mapping as per RFC-2576
notification-log Configure the Notification Log MIB
persist           Persistence for MIBS
target            target extention CLI from SNMP
Now, i wiil try to get work CBQoS.
Thanks

Invalid parsing schema for current workspace ID

I have an application that captures different SQL statements (they make use of DB links) and dynamically executes them on demand.
I use apex collections to get the result rows for the SQL and use them to both query on the UI as well as send out emails using the returned data. This is all OK and works fine.
I then added another feature to my application where I support the scheduling of the running the SQL / sending out of the emails. It uses the same logic as I use from within the application but it fails with the following error ...
Invalid parsing schema for current workspace ID
when the SQL is being used to populate the collection.
The scheduling is done using the apex plsql job scheduling package. It's as though the context that the job is running in is different from that of the application I created. The strange thing is that it can still see my tables that I created as the queries return data from my tables but for some reason seems to have an issue with the use of apex collections.
Any ideas or suggestions would be greatly appreciated.

Scott,
Today the error mentioned in the last post occurred 3 times - the highest number in a single day yet. Also, to add to the dilemma, a new one occurred:
ORA-20104: create_collection_from_query_b Error:ORA-20101: Application collection exists
Knowing that the create collection process is called from a post authentication process I don't see how that the collection could exist for that session... Any ideas?
Regards,
Dan
http://danielmcghan.us
http://sourceforge.net/projects/tapigen

List of detected bugs for 3.1.4.710

Hello,
Used this tool to develop simple model and found that the following are the bugs:
1) DROP MATERIALIZED VIEW not possible/ dependencies must be tracked when created as PREBUILD
2) LEVEL (in connect by clause)and DATE(as literal) special words does not recognized by view's parser
3) Even set genaration Materialized view with REDUCED precision (in the case of PREBUILD) no appropriate clause generated in DDL
Thanks

Hi Sergey,
thanks for reporting these problems.
1) DROP MATERIALIZED VIEW not possible/ dependencies must be tracked when created as PREBUILDI logged a bug for that.
2) LEVEL (in connect by clause)and DATE(as literal) special words does not recognized by view's parserFor such cases is good to have Select statement posted here.
Problem with LEVEL is fixed for next release, at least what we know as problem - your query can still have it :)
3) Even set genaration Materialized view with REDUCED precision (in the case of PREBUILD) no appropriate clause generated in DDLThis works in DM 3.3
Philip

Is this bugs for Sun Java System Portal Server 6 2005Q4 (errorStoreDP) ?

Hi,
I installed Sun Java System Portal Server 6 2005Q4 under window xp environment.
I used the following command to deploy war file, it worked for me (because I setup enough services and role for amadmin user), deploy/undeploy was worked very well for me.
pdeploy deploy -u amadmin -w amAdminPassword -g -p
amAdminPassword -v portletsamples.war
Two months later, I did not change anything (configuration) within the two months.
I use the same deploy/undeploy command to deploy war file again, I got the following error =>
errorStoreDP (sms-UNKNOWN_EXCEPTION_OCCURRED)
Message:The user does not have permission to perform the operation.
Why this condition happened ? is this bugs for sun portal server ?
I uninstall this sun portal server and reinstall it again, I still got
the same error message. why ?
But funny thing is that I format my machine, then install window xp and
install System Portal Server 6 2005Q4 again, then it works for me again.
is this reasonable ?
I really don't know why ?
Can someone help me ?
Thanks!

Hello,
It seems you are really asking how you should design your application to use portlets.
Your approach now seems to be that you would just copy your servlets to portlets. You can use the PortletRequestDispatcher to include content from your servlet. See http://portals.apache.org/pluto/multiproject/portlet-api/apidocs/javax/portlet/PortletRequestDispatcher.html
I also found the following discussion on this topic http://www.mail-archive.com/[email protected]/msg00481.html
But I don't think I'd recommend that approach for your application. How would you maintain the application going forward? You will have both servlets and portlets to maintain when you change the applicaiton. I assume you will be keeping the servlet application and using it also? Do you want the portlet content to match the servlet content always, or will they display differently?
Instead, what you might consider an model-view-controller approach and designing a web service (the model) for both applications (servlet and portlet, views) to consume.
As for the basics of porlet applications, the JSPPortlet will use JSPs for presentation of hte portlet content. GenericPortlet is the default implementation of the Portlet interface. Implementing the portlet interface means you must write the implementation yourself. Here are a couple of good tutorials to get you started on the Portlet spec:
http://www.javaworld.com/javaworld/jw-08-2003/jw-0801-portlet.html
http://www.javaworld.com/javaworld/jw-09-2003/jw-0905-portlet2.html
Also there is this JSE tutorial, but I don't know how current it is:
http://developers.sun.com/prodtech/portalserver/reference/techart/portlets.html
Hope that helps.

Setting Command Line Arguments for my Class

HI,
How do I set the command line arguments for my debug class. For example , I would like my user to type :
java Debug -LEVEL1
What should I do to implement this behaviour.
Thanks in advance...

     public static void main (String[] args){
          if(args.length > 0){
               int j = 0;
               BMsearch search = new BMsearch();
               try{
                    while (j < args.length){
                         if(args[j].equalsIgnoreCase(ONE_PATERN)){
                              search.addPaternForSearch(args[j+1]);
                              j = j+2;
                         else if (args[j].equalsIgnoreCase(PATERNLIST)){
                              j++;
                              while( ! (args[j].startsWith("-")) ){
                                   search.addPaternForSearch(args[j]);
                                   j++;
                              }//end while
                         else if (args[j].equalsIgnoreCase(PATERNFILE)){
                              j++;
                              search.readPaternFile(args[j]);
                              j++;
                         else if(args[j].equalsIgnoreCase(MATCH_H)){
                              search.heuristic = MATCH_HEURISTIC;
                              j++;
                         else if(args[j].equalsIgnoreCase(MATCH_H2)){
                              search.heuristic = MATCH_HEURISTIC_TWO;
                              j++;
                         else if(args[j].equalsIgnoreCase(OCC_H)){
                              search.heuristic = OCC_HEURISTIC;
                              j++;
                         else if(args[j].equalsIgnoreCase(COMB_H)){
                              search.heuristic = COMBINED_HEURISTIC;
                              j++;
                         else if(args[j].equalsIgnoreCase(JAVA_S)){
                              search.heuristic = JAVA_NATIVE;
                              j++;
                         else if(args[j].equalsIgnoreCase(TEXTFILE)){
                              j++;
                              search.readFileIn(args[j]);
                              j++;
                         else if(args[j].equalsIgnoreCase(TEXTURL)){
                              j++;
                              search.readURLFileIn(args[j]);
                              j++;
                         else if(args[j].equalsIgnoreCase(STOPatFIRST)){
                              search.searchall = false;
                              j++;
                         else if(args[j].equalsIgnoreCase(STOPatLAST)){
                              search.searchall = true;
                              j++;
                         else if(args[j].equalsIgnoreCase(VERBOSE)){
                              search.verbose = true;
                              j++;
                         else if(args[j].equalsIgnoreCase("-h") || args[j].equalsIgnoreCase("-help")){
                              printHelp();
                              Start = false;
                              break;
                         else{
                              System.out.println(" Error while parsing Parameter. ");
                              System.out.println(" type java BMsearch -help for all Options");
                              Start = false;
                              break;
                    }// end outer while
               catch(Exception e){
                    System.out.println(" Error while parsing Parameter. ");
                    System.out.println(" type java BMsearch -help for all Options");
                    Start = false;
                    j = args.length;
               if(Start){
                    if(search.verbose)System.out.println(" Parameter parsed, beginning with search ...");
                         search.starttimeTotal = System.currentTimeMillis();
                    search.search();
                    search.stoptimeTotal = System.currentTimeMillis();
                    System.out.println(" Whole search took: " + (search.stoptimeTotal - search.starttimeTotal) + " milliseconds.(Brutto) ");
          else{
               System.out.println(" Error while parsing Parameter. ");
               System.out.println(" type java BMsearch -help for all Options");
     }//end MAINThis is takem from one of my command line classe (a Boyer Moore Pattern-Matching application from an exercise). I don't know if this is the best way, but thats what I have done there for passing some arguments, where the order of them isn't pre-given (you can pass the params in the order you want).
The CAPITAL vars are pre-defined final Strings holding the param-names, e.g.
public static final String ONE_PATERN = "-p";
public static final String PATERNLIST = "-plist";
public static final String PATERNFILE = "-pfile";Another trick sometimes used in Linux/Unix, if you have only false/true combinations, are numbers from pow 2 (2,4,8,16). In C they are used because of the binary representation, but it has some benefits. E.g. a value of 2 (0010) and another true set on 4 (0100) results binary in 6 (0110), so you can mix parameters in only one value, and with a byte - array you could check, if the flag for a given param is set. But this way is a little tricky for the end-user.

DC LAN infrastructure - Mirror network for monitoring

Hi experts,
Does anyone have implementations examples of a "mirror" network in large datacenters designs for monitoring purpouses using TAPs (ex. netoptics or gigamon)? I'm evaluating some monitoring solutions but it's mandatory to configure mirroring on the switches to capture the traffic on the network. As the DC is large and there are another devices that need mirroring (IDSs, IPS, Probes) I'm thinking in implement a "mirror network" in all datacenter using TAPs. I'd like to see some implementations examples of a "mirror network" to evaluate if this strategy is viable.
Thanks in advance
Wesley

- OM3 multimode fiber
- Distribution network Gigabit SFP 1000Base T and FTP
There are so many combination of how to implement this project and it all boils down to your budget.
The two items I've highlighted are "old school".
- Poe for access switches
What kind of PoE? PoE, PoE+ or uPoE.
- Wardrobe 1 (150 Data and VoIP)
- Wardrobe 2 (60 Data and VoIP)
- Wardrobe 3 (200 data and VoIP)
Breakdown of how many PoE devices (and their respective power draw) per switch.

RT - Labview - Command Parser - Bioreactor

For the attached example, the Bioreactor program includes a command parser (which is good programming practice). Should only the commands from the host/HMI be included in the parser? In other words, if one was writing a program similar to this, should only the commands on the host/HMI be included, or if there was a state added to the state machine, should that state be added to the parser (IF IT IS NOT COMMAND ON THE HMI)?
Attachments:
Bioreactor (Scan Engine).zip ‏319 KB

I have and if I understood it, I would not ask. I am sure LabView and its RT utility are powerful tools if you know how to use them. I've been through the RT1 class, but NI left me stranded after that. They really stink on support and deny of any wrongdoing. So I appreciate the help.
Should only the commands from the host/HMI be included in the parser? In other words, if one was writing a program similar to this, should only the commands on the host/HMI be included, or if there was a state added to the state machine, should that state be added to the parser (IF IT IS NOT COMMAND ON THE HMI)?
It looks like only commands from the UI Event Handler are parsed.

Flash crashing when using Command + Option + S for Scale and Rotate?

Flash crashing when using Command + Option + S for Scale and Rotate?
It's happening to me when I use those hotkeys
Please let me know if it's happening to you too.
I don't know the cause but I need a fix.
I'm using Adobe FLASH cs6 for Mac
My computer:
Mac mini
Mid 2011
Software OS X 10.8.1 (12B19)
-Line

With all due respect to your totally coindescending reply, this is a bug in Flash. Happens every 4-5 times I use that menu item. Been happening for months, but we just installed a Brand new iMac (1/13). Quadcore 3.4 16G RAM and 1TB Fusion drive. Fresh install of CS6. Not running any other 3rd Party Software. Problem STILL happens in new Flash docs with small, simple vector Graphics.
So instead of blaming the users computers, how about you guys just fix the effin' problem? Thanks.

4500X command parser bug for monitor capture

Similar Messages

Maybe you are looking for