4507R-E and RME Config Change Report

Hello,
We have a new 4507R-E Switch which RME keeps reporting as "CONFIG_CHANGE" each evening. When you click to see the change, the only thing that has changes is the "ntp clock-period".
However, we have configured "ntp clock-period" as an exclude command in RME Config Managment.
Any idea's for anything else which could be causing this?

Bump.....We're still having this issue......does anyone have any ideas....

Similar Messages

  • Call manager and rme config archive report

    Hi,
    I know that rme does not support the call manager for config archive. It is clear.
    The RME home page show config archive status for failed devices and there are some devices which are not supported by RME config archive.
    I've set this devices to suspended state in RME but config archiv is trying with this devices also.
    This is a financial costumer and the local Financial supervisory authority would like to see all devices config is saving successfully.
    How can i exclude the call manager and similar devices from config archiv process and status reports?
    Regards,

    Hi,
    I would like to qoute from RME help.
    Working With Suspended Devices
    Suspended device state cannot participate in any RME application flows but all historical data pertaining to the device will continue to be maintained by RME.
    Nevertheless the RME is trying to fetch the config from suspended devices!!!
    What is the truth in this thing?
    Regards,

  • LMS 4.2.2 - RME Config Change

    I am currently receiving emails from LMS 4.2.2 that alert me of a config change on my switches.  The alerts are emailed after the periodic polling job that is run daily.  My problem is the email contain only the ip address of the device.  It would be nice to open the emails and see what change(s) made on the device.  Does anyone know if this can be done?  TIA                  

    i have seen this with SNMP timeout needed to be increased.
    please try to increase those values, and not the job completion values.
    I just saw in CP LMS 4.2 that the values are assembled on a new page.
    all of them ...
    Admin > Network > Timeout and Retry Settings > Inventory/Config Timeout and Retry Settings
    also in the navigator of the same last windows your screenshot is from try the device specific timeouts:
    Admin > Collection Settings > Config > Edit the Inventory/Config Timeout and Retry Settings
    HTH

  • Config change reporting with CW LMS

    Hi there,
    I spent some time on LMS and  found LMS can create a report representing which devices' configs had changed for last 24 hours. Does anybody know if it's possible to create a report representing which configuration changes have done for last 24 hours on which devices?
    Thanks,
    Yasemin.

    To explain more detailed what I’m trying to get is:
    Reports>Audit>Change Audit>24-hour
    Selecting all devices and CONFIG_CHANGE as category in the Selection Criteria gives most of the things what I want. The only but important thing I want to see addition within this outpu is who did which configuration change (we can say diffs only in config) in the same list in a tabular format.
    Do you have any idea?
    Regards,
    yasemin

  • ACS will not save the config changes to reports

    I have configured a very old ACS appliance, 4.1.  At this time this is what I we have to use.   The authentication is working fine, the reports for accounting, TACACS+ accounting is only saving the login and logout of the users and not any config changes that are being made. 
    I'm hoping that someone may have an idea of what accounting command I am using or if this older version has some changes that need to be done as the config/aaa lines I use today and work on newer version work. I was under the impression that this line "aaa accounting exec default start-stop group tacacs+"  would send every command to the tacacs server?
    aaa new-model
    aaa authentication login default group tacacs+
    aaa authorization config-commands
    aaa authorization exec default group tacacs+ none
    aaa authorization commands 0 default group tacacs+ none
    aaa authorization commands 1 default group tacacs+ none
    aaa authorization commands 2 default group tacacs+ none
    aaa authorization commands 7 default group tacacs+ none
    aaa authorization commands 15 default group tacacs+ none
    aaa accounting exec default start-stop group tacacs+
    aaa accounting commands 15 default start-stop group tacacs+
    any ideas would be3 appreciated.  thanks for reading
    Yvon

    Hi martijn,
    Are there some custom fields in this list or some duplicate columns? Please have a check.
    For more information about the possible reasons and solutions, see
    http://social.technet.microsoft.com/Forums/en-US/sharepointcustomizationprevious/thread/ae946f73-3126-41ad-833b-25e4cc2b7723#e22af3fe-8203-45c4-8d19-e18041a048e2
    http://social.technet.microsoft.com/Forums/en-US/sharepointgenerallegacy/thread/59895a6b-7f61-431f-a762-e3fd9d81fe34
    http://social.technet.microsoft.com/Forums/en/sharepointcustomizationprevious/thread/eba4cd7e-498a-465f-adea-decae44d7a8c
    Regards,
    Kelly Chen

  • Is there a way to find all config changes between clients and sap system

    We have our Dev system with clients
    310 - Developer make changes and create transport
    400 - Test client
    410 - a copy of our Production system (over 1 year ago0
    TST - this is our quality system with one client
    101
    Production system one client
    101
    I know if i do a database copy from Production to our TST system, both systems would be exact.
    Abaper Director wants to know all the configuration changes that are different between Devopment client 310 - Test and production.
    I told him that in development client 310 the abaper or functional users make most of the changes if they do  not get transported they would be missing.
    I cannot copy to client 310 otherwise we would loose all of our version management.
    Is there another way that I can see the config changes between all these clients.
    Thanks
    Joe

    You should be able to use tcode SCU0 
    Regards,
    Brian

  • Report to view composite  and master role changes

    Dear All,
    i would like to know list of master role and composite role changes, i searched in SUIM for change document for roles,which gives all role changes, which is not solving the pupose.my requirement is past perticular period any composite role got changed and new tcode got added to master role

    ramesh,
    try SUIM-change document -> For roles  / or reports
    Role:    RSSCD100_PFCG
    for  User         (RSUSR100)
      A profile    ( RSUSR101)
      An authorization (RSUSR102)
    A role assignment (RSSCD100_PFCG)
    just wanted to let you know that SAP meanwhile developed a new report RSUSR100N. I think it's only available with a certain SP level (at least in ECC 5.0).
    Thanks
    sri

  • Proposed changes to Business Model and effects on BW Reporting

    Dear All
    The Business is giving consideration to reducing (consolidating) its current number of Business Areas in use. They are stating they are not sure whether it will just rename some of the current Business Areas or create completely new ones.
    We are trying to establish what issues the proposed changes will produce in our reporting? There are obvious ones, around modelling for example, and we'll need to liaise with our Internal Audit but are there any specific Governance,  Risk Control or Compliance issues around reporting we should be asking the Business to address?
    Does anyone have any thoughts/experiences they want to share whose companies have undertaken something similar?
    Thanks in advance
    Helen

    I will just brain dump some thoughts - they may or may not be applicable
    Business Areas? as in the SAP term Business areas or the generic term
    If this were me - I would start to worry about the statutory requirements as business areas tend to get used for segment reporting under IAS14
    SAP brought out the segment ledgers in ECC6 to get around some of the process problems currently within the profit centre and business area concepts.
    These technical objects previously did not allow up to date balanced balanced sheets for the segments due to the month end SAP process runs required to fill areas of the balance sheet not posted directly by standard SAP transactions. (ie subledger GL to PCA posting runs)
    The new ECC6 segments resolve this by deriving (much like CO-PA derivation rules) the segment portion at posting time - thus the balance sheets balance
    From a reporting process point of view this is a massive tool in the armoury as some aspects of Sox or some countries GAAP compliance require a balance sheet to be available within 14 days of asking (hence the problem with month end processes)
    As with most aspects of BI and BW - the technology is the easy part (no matter what the postings in this forum suggest) - the problem is always the process and legal compliance, as reporting is the end game and only highlights problem with updtream processes.
    From a day to day process - the problems that you may encounter will be the change in processes of default business areas for automated postings (ie some business areas are going to take the hit for, say, write off amounts, unless that is SAP substitution and validation rules are written to allocate the postings correctly)
    What are you going to do with the historical data - are you going to remodel it with new look ups in BW and write the data back intot he cubes? As reloading historical data could take some time
    And then if you do restate the historical data - the internal auditors are not going to be happy as you now have no backup for the original tax/statutory submissions

  • [svn:osmf:] 10085: Fixing video width and height getting reset when there' s no true dimensional change reported by 'onMetaData'.

    Revision: 10085
    Author:   [email protected]
    Date:     2009-09-09 07:39:54 -0700 (Wed, 09 Sep 2009)
    Log Message:
    Fixing video width and height getting reset when there's no true dimensional change reported by 'onMetaData'.
    Modified Paths:
        osmf/trunk/framework/MediaFramework/org/openvideoplayer/video/VideoElement.as

    hi their i have tried your last code but their is a problem with it on my pc that when i click the send video button it gives the error related to vector,
    Vector deviceList = CaptureDeviceManager.getDeviceList()
    di = (CaptureDeviceInfo)deviceList.firstElement();
    returns zero.
    please help my email address is [email protected]
    kindly send me an email regarding the solution of my problem. i am using 'creative web cam' over XP windows.

  • Source Control 3.1 : History and change reports

    Robo Source Control 3.1 : History and change reports are allways empty. I only see titles on the file report.htm (using IE9 or Google Chrome).

    What I was saying in your other post was not necessarily that it will work differently on a 64 bit machine, simply that there were known issues with a 64 bit machine that are referenced in
    http://blogs.adobe.com/techcomm/2011/12/robohelp-9-0-2-is-now-available.html
    It may be the fix referred to there is simply to make it work the same way as on a 32 bit machine and clearly that is giving you grief. Only way way to find out.
    See www.grainge.org for RoboHelp and Authoring tips
    @petergrainge

  • Can we edit webi and deski reports and save the changes?

    Can we edit webi and deski reports and save the changed values for a particular column?
    If yes what rights should be granted to particular user?
    Will the report changes reflect at database end also?

    Both Web Intelligence and Desktop Intelligence comes with designers, where you have a GUI to design reports. 
    Web Intelligence you'd design in InfoView using the DHTML Report Panel or the applet-based Java Reporting Panel.
    Desktop Intelligence you'd use the Desktop Intelligence client.
    ReportEngine Java SDK (REBean) is what you'd use to programmatically create/modify Web Intelligence Documents.
    Desktop Intelligence Reporter COM SDK is what you'd use to programmatically create/modify Desktop Intelligence Documents.
    Sincerely,
    Ted Ueda

  • I am new to mac. how do i change the "cupertino" and Heavenly Valley ski reports on my dashboard to my area?

    I am new to Mac. How do i change the "Cupertino" and Heavenly Valley ski reports on my dashboard to Seattle and Stevens Pass Ski area?

    Hover your curser over the Widget until you see a little i appear, then click on the little i to access the Widget's settings.

  • Ciscoworks RME 4.0 SNMP Config Change

    Hi,
    I was locked out one of my routers.  I cannot access it via Telnet, SSH, TFTP, SCP, etc.  However, I remembered once I reconfigured the router via SNMP community string.  Does anyone know how I can change router config via SNMP community string using CiscoWorks RME 4.0?
    Thanks!

    You can use RME ---> Config Mgmt --> NetConfig --> NetConfig Jobs . For specific steps, read the users guide below for information about different user defined task you can use.
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_resource_manager_essentials/4.0.5/user/guide/netcfg.html#wp1134190

  • AM Config and Application property changes in JDev 11.1.2

    Hi All
    I have recently moved to Jdev 11.1.2 and there are changes to some very common features e.g.
    1. AM configuration opens bcf4.xcfg file and I can't find how to change my JDBC connection from URL to Data Source like I used to do using Dialog box earlier.
    2. Application properties -> Deployment doesn't show me if I want to generate weblogic-jdbc.xml file or I want to port policies n credentials etc on deployment. I can't find this anywhere.
    Is there a link or document which details about IDE changes for such common features. The document about what's new doesn't mention that.
    Thanks in advance

    another one..
    right click the AM
    select configurations..
    selct the Names (confugrations)
    click Edit button... to Edit the configurations..
    another one with Johns approach..
    double click the AM
    click configurations tab
    right click the appropriate configurations..
    edit..
    :)

  • Prime Infrastructure 2.0 - Alert on Switch Config Change

    We are in the process of testing out Prime Infrastructure 2.0, is there a way to get an alert when a device's configuration has changed, and send out what has changed in email? I have scheduled Config Archiving for all of my devices, and i can see the config differences when a changes is made in the Prime GUI, but we currently use Kiwi CatTools to send out emails that show what devices had configuration changes and what those changes were, it would be nice if Prime would do that so we could do away with that service. I have looked through all of the reports but do not see anything.

    Hi,
    I know this feature is there is LMS ,where you can configure the AUTOMATED Action based on Syslogs to get an Alert for config change or any other changes ,however I do not see this option available in PI  2.0.
    Syslogs are not compltely supported in 2.0 but in PI 2.1 we should have the complete support for syslogs.
    Thanks-
    Afroz
    [Do rate the useful post]

Maybe you are looking for