5.1 audio not working
Hey guys any help would REALLY be appreciated, I'm a bit of a newbie so carefull steps would great. I've been struggling for a while now with this:
CPU=AMD Athlon 64 processor 3500+
RAM=1.00 GB
Motherboard=MSI NVIDIA nForce 4 SLI k8n Diamond
VGA=GEFORCE XFX 6600GT
OS: Windows XP, Home Edition, Service Pack 2
Problem; I've recently baught a Logitech 5.1 X-530 speaker system. The motherboard seems to only recognise the front speakers. No sound comes out of the rear and center speakers. I've been told this has something to do with the motherboards in built sound card and that something needs to be enabled or changed. Please help with this problem. (i've updated the creative sound blaster audio drivers and set audio in control pannedl to 5.1) (also note that these speakers require no drivers)
Thanking you
I was wondering if anyone has found a solution to this problem because i have also run into the same thing.............
I plugged my speakers into the correct color coded plugs but it still dosen't work......i can plug each separate plug into the green plug on the back of the motherboard and all speakers work in that plug....but when i try to plug them in their color coded holes only the green plug speakers work....
any ideas how to fix it??
Eric
Similar Messages
-
Iphone 5.1 update messed up sound. Audio not working in youtube, music and video apps. Phone is not muted! nor is volume turned down
Basics from the User Guide are restart, reset, restore from backup, restore as NEW. Unless you've tried ALL of these, you're not done troubleshooting.
-
Iam using o player... Ac3 dts audio not working msg showing
Settings > General > Reset > Reset Network Settings
Contact the carrier. -
HT201210 AUDIO NOT WORKING PROPERLY AFTER INSTALLED IOS7
After installed ios 7
photos not able to see fully
audio not working properly.... [no treble, no depth in sound, very low soung even the volume is full]
get strucks while playing gamesThis board is full of people that are update crazy...
even when they have perfectly good working systems.
i know i thought well it's just a security update not a major update.
Best advice... whenever updating the OS, unplug all
firewire devices.
will take note of that from now on.
Was this auto-update? Try downloading the file and
running the update again with all firewire devices
unplugged.
While the 828 is disconnected perform the factory
reset
again.
Disconnect the firewire cable from the 828mkII
-Press the Setup knob
-Turn the Setup knob all the way to the right
-Press the Select knob
-Press the Value knob
-Power off the interface and plug the firewire cable
back
in
-Power the interface back on
i have the original 828 not mark 2, so no reset i know of, just power on off.
After the Mac updates... reboot and plugin the 828,
see if that doesn't get you going.
pancenter-
cheers pancenter, i'll give it a whirl updating without the interface plugged in. thanks for all your help. -
Windows 8.1 beats audio not working
Product name: HP ENVY TouchSmart Sleekbook 4
after update windows 8.1 beats audio not working
This question was solved.
View Solution.Download the file below and instll , Restart and give your beats a try again. If you cant find Beats go to (Control Panel) and search (Beats Audio) then right click on it and create a shortcut, you should now have a shortcut to Beats Audio on your (Desktop)...
Let me know if this helps ...
DOWNLOAD LINK
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&softwareitem=ob-124012-1 -
Laptop left Speaker audio not working
Sir,
I have dv-5 1102 tu model laptop, in that left speaker audio not working. But, in headphones & Speakers have no problem in both left & right audio.
Kindly do the needfulHey @KKVK ,
Welcome to the HP Forums!
I understand your left speaker is not working on your dv5 notebook.
If the headphones are working it would tell us the sound card is fine. The same properties are applied to the speakers and the headphones in your audio control settings.
You could try a system restore to before the issue started to make sure it's not something in the operating system. To perform a system restore see the following guide: Using Microsoft System Restore (Windows 8) or Using Microsoft System Restore (Windows 7).
If this fails I would suggest contacting HP Phone Support to send the notebook for service. Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the following link to get the support number for your region: Phone Assist Worldwide.
Thanks!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP. -
Audio not working on channel 5 and 7,, okay on all others????
audio not working on channel 5 and 7,, okay on all others????
dalharris wrote:
audio not working on channel 5 and 7,, okay on all others????
Without knowing all of the specifics in your situation, you may want to try these options:
- If you have a DTA, and your remote control has a LANG button on it, press it.
- If you have an HD or SD full cable box:
Most low or no audio issues can be corrected by setting the Optimal Stereo output of the cable box. Here are the steps: Press the Menu button twice on your remote control. Select Setup. Select Audio Setup Under the Optimal Stereo setting, choose "Select to Optimize" and press OK/Select on the remote control
- The audio settings on your cable box may have accidentally been changed:
Press the Menu button twice on the Comcast Universal Remote Control. A new screen below will appear, with the top-left option automatically selected.
Use the down-arrow key (above the Info button) to navigate to Setup and press OK/Select (the center key on the remote control in the middle of the 4 arrow/directional buttons).
Use the down-arrow key (above the Info button) to navigate to Audio setup and press OK/Select.
The Default Audio Track will default to the first option–Channel default–which which is always the channel’s main audio track (unless it was previously changed).
Press the right-arrow navigation key to change the audio track. Changing this selection will instantly change the audio.
1. Press once for English
2. Press twice for Spanish (Español) OR to activate Video Description (DVS)
3. Press three times for French (Français) 4. Press four times for Portuguese (Portugues).
5. Then press the Exit button (above the Volume button) to resume program viewing
Please note: These audio options can only be heard if the program provider or cable channel is providing that additional audio option.
- If the above does not help, look at the remote control for your TV set (not your cable box) as the TVs language settings may have been accidentally changed (sometimes labeled as MTS or SAP on the remote or via your TVs settings menu). -
sound/audio not work
Model- Compaq M2000.
S/N; CNF550117L,
P/N-EE462Pa#UUF
M2235Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
Digital Audio not working on Satellite A505 S6012
My digital audio stopped working suddenly. I use HDMI to send the video out of my laptop to my projector. I had been successfully using, for over a year, a digital audio cable in the headphone (SP/DIF) jack to output the sound to my home receiver. The default audio set in the control panel is Realtek Digital Audio.
If I set the output to speakers and plug headphones in the jack, I get sound. If I set the output to Realtek Digital Audio and plug the digital audio cable in, I get no sound. I've tried new cables, changing the input to a different conection on my receiver, reinstalling the Realtek driver, and, as a last resort, completely recovering my laptop to the factory setting. Digital Audio still does not work.
Any suggestions? This is the main way we watch movies in my home.hi, have you try out srs audio program it nice!
can u help me if u have make for yourself a recovery dvd of S505 S6012 because to mine i didnt do it and it gives me a lot of problems.
if you have please i would like to have it.
thanks.... -
HDMI Audio not working on Q190 (along with all higher level Audio Formats)
Help, I have been given the run around via support, I cannot get the HDMI audio to work with my Pioneer Surround Sound, only the Intel display audio shows in control panel (Win 8 X64) and the RealteK S/P Dif port and it is not capable of supporting 7.1 sound or bitstreaming or DTS, Dolby HD, Etc. Tec support appears not capable of fixing the issue and wanted to send me to software support and pay. I have only had the machine for 4 days and it has never supported higher level sound.
Every other device I have (had or currently) connected to the receiver works just fine. I have to figure this out or return the machine, the audio is the most important aspect for me. Besides when you advertise 7.1 support the machine you sell should be able to do it.Hey guys,
I have had this Q190 with the Celeron CPU since last week and I am using XBMC Frodo and the HDMI is connected to my AVR Onkyo TX-NR809 and from the Onkyo to the TV. And the sound is 7.1 with PLIIZ. It works fine. I think it may be some driver problem because Realtek Audio which is in the Q190 works fine with the Win8 preinstalled. Realtek is kind of bad with driver because I lost my wifi after upgrading to Win 8.1. After a few days with no wifi, I found out that the driver was bad, yes it was a Realtek wifi driver but posted by Lenovo for W 8.1.
I have another friend who also just bought the Q190 and he reported no audio problem so I think it is just a matter of trouble shooting the drive and configuration. I do love the form factor of the Q190. -
HP Pavilion p7-1421 Desktop PC BEATS AUDIO not working.
Hi, new here with thankfully my first problem with the desktop in the subject line.
Somewhere along the way, the Beats Audio stopped working correctly. The Equalizer
sliders will not move at all, and the "Test Speakers" button will highlight the left, then right
speaker, but no sound will be produced.
For background, I did install StartDoc, a program that gives one back the original Windows 7 "Start"
button and desktop. Other than that, I have not installed anything, except the reccommended HP upgrades.
Also, the machine is obviously running Windows 8, and I have NOT switched to 8.1.
I see on the Notebook page lots of questions re. Beats not working and solutions, but each user is asked
for the specific model, OS etc. This is why I chose to post a new thread, so that the experts can address
my exact machine.
Thanks in advance,
John
This question was solved.
View Solution.Hi srv1954,
I suggest reinstalling Beats Audio.
Open the Charms menu, select "Search".
Enter "Recovery Manager" and then select Recovery Manager from the list. Click "Yes "at the User Account Control.
Select "Hardware Driver Reinstallation". Select "Next". Select 'IDT High Definition Audio CODEC".
Select "Next"
Follow prompts to reinstall and reboot your PC.
Jaco.
****I am not an HP employee****
Please give a" Kudos" if advice received is relevant or" Accept as Solution" if your problem has been solved.
+++++++++++++++++++++++++++++++++++++++++++++++++++++
H8 1380t CTO, Intel i7 3820
16 GB DDR3
Pegatron Motherboard- IPIWB-PB (Pittsburgh), Radeon HD 7570 1GB. Win 7 Home Premium upgraded to Windows 8.1 Pro.
Envy Phoenix 810-150se, Intel i7 4820k
16 GB DDR3
Pittsburgh2 Mainboard, NVIDIA GTX 645- 2GB GDDR5. Win 8.1 Pro.
HP 560z CTO AMD Phenom II X6 1090T
16 GB DDR3.
Radeon HD 6570
Win 7 Home Premium upgraded to Win 7 Pro.
HP ENVY 17t-j000 CTO Quad Edition Notebook. I7 4702mq
12 GB DDR3
Nvidia Graphics
Win 8 Pro
Errare humanum est. -
HP Envy Touchsmart 4-1118TU - Audio not working - Windows 8.0
Hello,
The audio on my HP ENVY touchsmart notebook has stopped working - notebook is approx 12 months old.
This occured seceral months ago, uninstalled the driver, reinstalled the driver and it fixed the problem.
Has now happened again, sometimes resetting fixes the problem but after several events it has now stopped working.
Tried uninstalling and reinstalling the driver again, but has not worked this time.
Currently running Windows 8. Have thought updating to Windows 8.1 may help rectify any bugs - but have not tried the upade as of yet.
Any help would be appreciated.
JamieHi,
Please use the following instructions:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c03257712
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
HDMI audio not working in HP Pavilion dv4 1290-br
Hello, people.
I can't get my HDMI audio to work on my laptop (HP Pavilion dv4 1290-br). The output of aplay -l is:
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: STAC92xx Analog [STAC92xx Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: STAC92xx Digital [STAC92xx Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
I've tried setting ~/.asoundrc, /etc/modprobe.d/alsa.conf, /etc/modprobe.d/alsa-base... Nothing works.
Can someone help me out here?
Thanks!I've a DV4 and I did get it to work many months back; and have not done it since. If I recall correctly, I had to resort to JACK. YMMV
-
Audio not working in Photo Booth, video works fine
When I record video in Photo Booth the video works fine, the audio does not work. I have looked through other forums and tried what they have suggested but nothing is working. I sware it worked once but now I can't figure it out.
Lance Mcvickar wrote:
I have listed it with google and you would think with the .com we would come in first in a search but we are slowly going further and further back in the listings and never made it to the top. Any insight as to why that might be.
Lance ~ It could be because iWeb websites are not made to be search engine friendly. See this article:
_SEO For iWeb: How to get your iWeb Websites into Google & Other Major Search Engines_
By the way, a tip... Instead of posting your site's URL like this:
www.thehorseyourodeinon.com
...include the prefix like this:
http://www.thehorseyourodeinon.com
...then it will be easily clickable in your post. And before posting, you can switch from Compose mode to Preview mode to verify that the hyperlink actually goes to your site when clicked. -
Audio not working after I format from win8 to win7
product no:C0V01EA#ABU
Model:hp envy sleekbook 6-1126sa
Memory: 4096MB RAM
Processor: AMD A6-4455M APU ith Radeon (2CPUs) 2.1GHz
Hello, I have a problem I was unable to solve. I formated my pc from win8 to win 7 64bit , I installed all the drivers but my audio is not working . I would be glad if you can help me solve this problem.
Above is my product and model number.Hi:
Please see if this driver works for you...
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-107001-1&cc=us&dlc=en&lc=en... -
Audio not working...MBP mid 2009 to HDMI
I have my MBP hooked to Sharp Model LC-C32370 with Mini Displayport to HDMI cable(belkin), using Belkin Aux cable plugged into MBPro's headphone port and then to TV....audio still not working. Any suggestions?
On the Thunderbolt to HDMI converter/cable I have for mine, the volume controls don't work in System Preferences. As per the maker's indications, I use the Audio MID Setup utility to control it. Yours may work likewise.
Maybe you are looking for
-
Report for vendor master changes
Good day, Please can you assist with this issue, Report S_ALR_87012089,program RFKABL00 Version ECC 6.0 This report does not reflect the old and the new values for changed bank details. It does not show anything under the old value and shows **delete
-
Maintain text in report in different languages
Hi Gurus! I have a report in different languages. Now when user logins in different languages, I want him only see English in GUI in that specific report. How do I do that? I don't want to re-translate again all the text in text elements and selectio
-
Migrating fm CF 5/MS SQL to MySQL
Time for us to take a quantum leap. We want to upgrade everything from Cold Fusion 5 to the current version. Then, we want to migrate from MS SQL 7 (on a Windows 2000/NT server) to MySQL (Apache). Our ecommerce solution is fairly complex with stored
-
Missing the sign in seal (assuring validity) for Yahoo email sign in page
The sign in seal is an option you build for sign in id and password for yahoo emails. it assures authenticity. It shows up, except on firefox. I would appreciate your comments please. Thanks in advance..
-
My OS is 32-bit and i have already downloaded the SQL Server 2012 Express but i cant find the SQL Server Management studio so please tell me how can i get it?