5.5 Not taking a good charge/stuck in a cycle?

So, did the 1.2.3 firmware when it came out and I didn't have any problems with it until I let my iPod battery drain all the way yesterday. Afterwards, i plugged it in to my USB and let it sync up and charge for about 3-4 hours and I figured everything went well. I took it off and went to use it again and it crashed the second I tried to play something. Black bar across the bottom of the screen and a dim apple logo. There are clicking sounds though the head phones when you hit buttons. I plugged it back into my computer's USB and it goes to the dim apple logo for a few seconds and then stays on "please wait, battery is very low.", or whatever. it never gets out of that state and the computer never recognizes it.
I borrowed a friends wall-adapter (firewire based) and when it is plugged into that, the iPod boots up properly. After a few minutes it comes up "Charged" as if it was fully charged, even though 5 minutes ago it claimed it was completely dead. If I unplug it from the wall and into my PC, the PC will see it and let me sync with it, but the battery icon still indicates that it is fully charged. I can also unplug it and navigate the menus for a minute or two but once i play something it starts all over. I can reset it while it is plugged in to the wall adapter and I have done that like 6 or 7 times now but it doesn't seem to fix anything. I can't reset it while it is unplugged because half-way though the reset i get the black bar and it just dies.
I performed a restore when it was connected to my pc and that didn't fix anything either. Also, during the restore, after the progress bar dissappeared from the screen and the iPOD reboot itself, it got stuck on the low battery screen again and I had to switch it to the wall-adapter and then back to the USB to complete the restore.
Everything seems indicative of a dead battery but I refuse to accept that because I used it for almost 12 hours straight before all this started to happen. Batteries slowly last shorter and shorter over time, if I am not mistaken. My school has a genius bar or whatever but it isn't open till Monday and I expect they are going to tell me that I need to send it in and charge me 30 bucks, which is also unacceptable. I've noticed a lot of other people seem to have this problem or something similar.

Those all sound like reasonable causes.  I do not know the answer.  There is probably an Apple Support forum for the ipod that could help.  Also try the ipod Help in itunes.

Similar Messages

  • Activate BI content - not taking the good datasource

    Hello,
    When I copy Bi contents, the datasource is coming from my BI system (client 000) but I want to extract from the datasource coming from my other logical system client 001.
    How can I configure BI contents activation to search datasource and use the other logical system ?
    Thanks a lot !
    Regards,
    Aurélien

    In RSA1 -
    >Bi Content ---> There is one button called 'source system assignment' ( The button is cross mark on yellow background'
    Here you can maintain from which source system you want the data sources to be assigned.
    Assign points if  found helpful.
    Regards,
    Mahendra

  • HT4009 Not very user friendly! Where is the place to report a problem!? I have been billed for an in-app purchase but not had the goods - I received an error message telling my I hadn't been charged at the time and now it is on my bill! What can I do?

    Not very user friendly! Where is the place to report a problem!? I have been billed for an in-app purchase but not had the goods - I received an error message telling my I hadn't been charged at the time and now it is on my bill! What can I do?

    You can try contact iTunes support via this page : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption

  • Looking for a good note taking app: Are there new features for the Notes app in iOS6?

    Hi,
    I've read that the Notes app with Mountain Lion will be available for OS X as well, and I was wondering if there will be any significant updates to the Notes app coming in iOS 6?
    The Notes app in Mountain Lion supports, as far as I know, text formatting, images and attachments. The Notes app in iOS 5 does not have any of these features, yet still it is claimed that the OS X client will sync with the iPhone, iPad and iPod touch. This means that there must be some rather significant updates coming for the Notes app in iOS 6 to match up with the features of its Mac counterpart. Still, no updates to the Notes app are listed in any of the iOS 6 feature lists I've seen so far.
    I'm looking for a good note taking app for OS X and iOS. I don't like how Springpad works, neither did Evernote work out for me, it's just too complex - I like Simplenote a lot though, it's just that its approach is too radical in my opinion. I was thinking that the Mountain Lion Notes app might be a good alternative because it combines simplicity with rich text formatting and attachments. I kind of hate the skeuomorphic user interface though.
    best, Ian

    You are only addressing other iPad users here & no Apple employees. We have no way of knowing, so you'll have to wait until iOS 6 is released.
    Here's some general info.
    Working with Notes and Documents on the iPad – Alternatives & Suggestions
    http://ipadacademy.com/2012/04/working-with-notes-and-documents-on-the-ipad-alte rnatives-suggestions
     Cheers, Tom

  • My Ipod nano touch is not charging, not showing in my PC or laptop. Last I saw an apple icon and low battery signal. There after the screen is black and no power not taking AC or PC charge. What Can I do?

    My Ipod nano touch is not charging, not showing in my PC or laptop. Last I saw an apple icon and low battery signal. There after the screen is black and no power not taking AC or PC charge. What Can I do?

    If the Reset didn't work, you'll need to do a Restore.
    From iTunes, select the iPad and then select the Summary tab.  Follow directions for Restore.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finished, you will be asked if you wish the contents of iTunes to be copied to the iPad.

  • Auto Goods Issue not taking place

    Hii All
    I hv Maintained backflush indictor in work center and in MRP2 view it is maintained as Workcenter
    decides whether to backfluch .
    But the auto goods issue is not taking place when the production order is saved and confirmed.
    The stock remains the same ..
    Can anybody tell the reason for that
    Regds
    Rakesh

    Hi Rakesh,
    what is the control key u have maintained in Routing?
    if u r using Control key PP01 - Routing/Ref. op. set - internal proc., then after Production Order confirmation u have to do MB31- Goods Receipt for Order, with movement type 101.
    If u r using PP03 Routing - in-house prod. auto. goods rct, then it accepts only single operation in a Routing (or) if u r having say more than one operations in a routing, then u have to give PP03 control key for the last operation.
    I think u got it...
    revert back if u have doubts.
    Thanks & Regards,
    Santosh

  • Not taking care of good paying current customers

    It is a shame another big company not taking care of their current customers. offering deals for new customers and not helping out current customers is a great way to loose a customer. my service agreement is up and would save me a good bit to cancell service, have verizon pay to remove hardware then resign next month for a lower rate. just doesnt make good buisness sense.

    Verizon reminds me of the old SNL skit... "We don't care. We don't have to. We're the Phone Company"
    See http://stopthecap.com/2012/08/23/were-the-phone-company-we-dont-care-we-dont-have-to/

  • Goods release is not taking place

    Dear Friends,
    i am getting error while releasing goods from plan order to production order.
    my case is as follows
    while converting pl.order to production order, goods movement is not taking place.even though when we save the entries, production order is saved with the order number.then i go for goods receipt MB31,"goods is not released" message is displaying.
    In the production order system is giving error message
    Business transaction can not be carriedout.
    system status WERC IS ACTIVE (ACT 600026850010)
    Diagnosis :
    Object Act 60002685 0010 has system status WCRE (work centre until release).According to this status transaction release opration is not allowed.
    Procedure:
    you can only carryout the requested function if this is allowed according to the status of object.
    can anybody help on this.i think some configuration is required between plant and business area.
    please guide me!

    Hi Krish,
    There is a problem with the tasklist type usage used in work center.
    Check in Basic data of the work center "usage". You can see the defination of that in customizing transaction "OP45". In your case the tasklist type is set for "Until release" (check box), this means that this work centre will give error if used in order at the time of "Releasing" the order.
    Resolution:
    Use a proper task list usage in the work center or change the existing one by removing the check box activation for "Until release".
    Regards,
    Prasobh
    Award your points if this was helpful...

  • My ipod is not taking a charge. Can anyone help?

    I have an older Ipod which is not taking a charge.

    How are you trying to charge it? Have you tried a different cable to see if that makes a difference?
    If nothing else, your iPod's battery may be shot and in need of a replacement.
    B-rock

  • HT1349 My daughter's IPOD 5 Touch is not taking a charge.  It show a picture of lightning bolt and above that it shows a picture of a battery with a very slim red line at end of battery picture.  She just got this in August of 2013.  What could be the pro

    IPOD 5 Touch is not taking a charge.  It shows a picture of a lightning bolt and above that a picture of a battery at the end of the battery is a slim red line.  This was purchased in August 2013.  Could it be battery or ac charger adapter or usb cable?

    Those all sound like reasonable causes.  I do not know the answer.  There is probably an Apple Support forum for the ipod that could help.  Also try the ipod Help in itunes.

  • Ipad not taking a charge

    ipad2 not taking a charge

    The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom

  • HT4060 my ipad has been charging for days and not taking the charge what else can be wrong.?

    i have an apple i pad 16 gb...i have it charging for days and its not taking the charge what else can i try...

    Could be the charger, cable or the iPad.
    Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
    And this - Unplug the charger from the iPad and then replug. May resume charging.
    Or - Recalibrate the battery. See link below.
    The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    Best Practices for iPad Battery Charging
    http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    How to Save and Prolong the battery life of your new ipad
    https://discussions.apple.com/thread/4480944?tstart=0
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    To Extend a Device’s Battery Life, Get to Know It Better
    http://tinyurl.com/b67c7xz
    iPad Battery Replacement
    http://www.apple.com/batteries/replacements.html
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom

  • Hello good evening. my iphone 3g I try to restore with itunes and not completed the restoration gets stuck and disconnected and brand UNKNOWN ERROR -1. can help me please.

    hello good evening. my iphone 3g I try to restore with itunes and not completed the restoration gets stuck and disconnected and brand UNKNOWN ERROR -1. can help me please.

    Try a different cable...
    yescadnk wrote:
    ... UNKNOWN ERROR -1. can help me please.
    Error -1
    Attempt to restore your iOS device two more times.
    If the issue is still unresolved, the device may need service.
    From Here  >  http://support.apple.com/kb/TS3694

  • IPhone 6 is not taking charge

    I purchased a brand new iPhone 6 from "Smart Avenue" phone shop located in Avenue Mall (Swefiyeh Mall), Amman (Jordan) in November 2015. In late December it started not taking charge normally. I can sometime (not in all attempts) charge the iPhone with completely switch off state. I checked with multiple chargers from other users with no luck. I left the phone with the seller shop for more than a month with no result. They suggested me to send the phone to USA for a 200USD charge to get a replacement which I did not agree. I believe there should be a way to get it repaired in Amman (Jordan) for free of Charge.
    I wonder if anyone in this forum can suggest me with a solution to get the phone repaired by myself or through some local authorized service provider for free.

    You've been told what the solution is but refused to accept it. We can't help you.

  • Any good note taking apps that don't use the cloud to sync to PC?

    I'm looking for a note taking app that has an iPad client and a PC client that also acts as a server. I want to be able to keep my ipad notes in sync with my PC notes for work without using any cloud-like services. My iPad is connected to the same corporate network as my PC.
    Any suggestions? I'm not fussed about special features like handwriting, images, colours, formatting, etc. folders and tags would be nice though.

    No, I don't sync via iTunes any more, but the option is clearly still there, with a warning about what might happen if I turn it on.

Maybe you are looking for

  • How to get an mbean to create an object to be used in invoke

    The topic says it all. I am confused. Either way, this is what i am trying to do. I have two classes i have registered as mbeans and can access from a remote jvm. What i need to do is to invoke a method in one of the mbeans which takes an object of m

  • How to specify the saving path pdf by a "saveas" button in Javascript?

    Hello, Firstly, I use LiveCycle ES3 designer on PC. I created a form with a button executing a Java script that opens a dialog box "save as ..." like this: \ \ Script save-as \ \ app.execMenuItem ("SaveAs"); I would like to predefine a file path to o

  • Error while configuring digital signatures.

    Hi, I am running the program DSIG_BOOKING_EX to configure the digital signatures. I get the error : SSF error: Unable to find external security product. When i execute the program SSF02 i get a success message. Regards, Sridevi

  • ME013 Document type RD33 not allowed with doc. ca tegory B

    When I try to post an SC, i get the following error: ME013 Document type RD33 not allowed with doc. ca tegory B.  I am on SRM 5.0.  I have maintained config (V_BBP_TARGET_OBJ) to create a PO if info complete and I have set up BSA in the org structure

  • HTMLEkitorKit color change does not work on existing color

    My problem is that I use StyledEditorKit.ForegroundAction to update the color of the selected text. It works the first time but if I select a substring of the text with the color attribute and apply the foreground action again the color attribute doe