5 minutes 6 seconds then freeze

Hi. I've been suffering the same problems as most with I chat AV 3.
I get the same did not responds and faild to answer problems. My Girlfriend who uses aol an a pc always has to start the video conferance.
The biggest problem is that when we've been talking exactly 5 minutes and 6
seconds the video freezes and we have to restart. This happens with tiger and with panther. I'm not sure if its a problem on my side or on her pc side.
I've followed a lot of the help already in thes forums but this one has me stuck.
Any help would be great
Gerry

HI All,
James has posted that his faster computer will now connect succesfully now that he has a new camera and Drivers for it.
This would hint at drivers or possibly the part of those drivers that allow the video Quality to be set to a point that frames (rate) do not over run the Mac's buffer.
In Panther and iChat 2.x you could see in the Consol Log that iChat was dropping frames but this info no longer appears. There was no proof that this was the problem. Nor does it seem to be cured by the buffer in iChat 3.
The only real work around is to stop the chat and restart it.
Ralph

Similar Messages

  • I did the recent update on my ipad 7.0.4 and now it keeps freezing up and can not use it. Tried reboot and works for a second then freezes right up again. Anyone else have this issue or know a fix?

    I did the recent update on my ipad 7.0.4 and now it keeps freezing up and can not use it. Tried reboot and works for a second then freezes right up again. Anyone else have this issue or know a fix?

    Madmonkey,
    First thing to try is to reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.
    Gaylefromnewhope,
    Seems like you tried this all ready and it didn't help.
    Next might be to reset all settings.
    Settings > General > Reset > Reset all Settings
    Note that when you do this you will not lose data but you will have to enter all passwords again.
    If that doesn't help you might tries a restore of your iPad using iTunes on the computer you normall sync with. Do a backup and save all data first. Or
    Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

  • Video only plays for a few seconds, then freezes

    The video, which I got from the apple website, plays fine in iTunes but once I upload it to the iPod it will only play for a few seconds before freezing and becoming nonresponsive. Is this a software problem? Anyone know of a solution? Thanks.

    Or you can follow these instructions.... (adopted from btabz)
    Here are more detailed instructions on how to go back to 1.0, espescially if you bought your iPod in the last couple of months and it came with 1.1.
    First, please download the older version of the iPod Updater here...
    http://appldnld.m7z.net/content.info.apple.com/iPod/ww/win/061-2225.20051128.PDW nw/iPodSetup.exe
    Now install that updater and restart your computer.
    Now open the iPod updater (Start-->all programs-->iPod and find the iPod updater you just installed
    Open the iPod Updater and connect your iPod. With that older version of the iPod updater you just installed, restore your iPod by clicking restore.
    The iPod will restore and go back to software version 1.0. Now reload everything back into iTunes.
    If you don't want to restore, see this...
    http://discussions.apple.com/messageview.jspa?messageID=1813873

  • Plays only 20 seconds, then freezes

    I have the U2 edition iPod and on Friday I added new songs (roughly 150?). After I did that my brother borrowed it and used his own headphones.
    Since yesterday, when I play songs, it only plays 20 seconds and then stops, moves to the next song and it repeats the cycle. When I use the clicker to go back or change playlists, it freezes for a few seconds and then the same cycle starts again.
    I dont know what happened or how to fix it.
    Any suggestions?
    Windows   Windows XP  

    apple replaced it

  • Final Cut Pro 4.5 and Final Cut Express 3.0 - 5 minute captures then freeze

    Something I have found with Final Cut Pro 4.5 and Final Cut Express 3.0.
    After Updating to Tiger - 10.4.11 and Quicktime 7.4.1 - Both Pro 4.5 and Express 3.0 will not capture more then 5 minutes and 12 seconds. If you are having this issue the solution I used to fix both Pro and Express issues was an update on the software. Final Cut Pro 5 fixed the problem (or 6 if you can) and with Final Cut Express, version 3.5 fixed the issue but if you can go with FCX 4.
    Let me know if this helped or if you have found a different solution. Downgrading the os might help but that is too much of a pain and it's time to upgrade the software anyway.

    #29: Need AGP Graphics card
    Shane's Stock Answer #29 – Error: “Need AGP Graphics card”
    http://docs.info.apple.com/article.html?artnum=302667
    The Final Cut software is looking for a graphics card type that is required for that version of the software. FCP 4 and FCP 4.5 were released when AGP cards were the requirement. Attempting to open this on a Mac with a PCIe graphics card, such as an Intel Mac, will cause this error. FCP 4.5 is not supported on the Intel Macs. If you happen to have a PowerPC Quad processor Mac and get this error, you can try this hack:
    http://www.xlr8yourmac.com/feedback/finalcut_pro_on_oldmacs.html
    You can also press the "esc" key as you launch FCP. This enables FCP to open and run, but know that it might not work optimally.
    If that doesn’t work, or if you have an Intel Mac, you are going to have to upgrade to a supported version of FCP…and FCP 6, part of Final Cut Studio 2, is the latest version.
    Shane

  • An Animated GIF displays, i.e. moves, for about 5 minutes, then freezes. Other GIFs from the site work indefinitely, and this GIF works indefinitely on IE. Why does it freeze in Firefox?

    An Animated Avatar GIF file moves as expected for about 5 minutes, and then freezes. Other animated avatars from the same site work fine, and move indefinitely. To confirm that the site had not exchanged the file for a non-animated version, I right-clicked and selected 'View Image Info' and when I did so, it moved for about half a second. (The image file was the one uploaded.) Loaded the page in IE, this avatar moves indefinitely.
    Any ideas why an animated GIF stops in Firefox?

    The answer is that Animated GIF files include a Loop Enable Flag as well as a Loop Limit Count. This GIF had a count which should have allowed it to loop for almost 2 hours. But in Firefox it only loops for about 5 minutes.
    It appears Firefox is misinterpreting this value to be a Frame Count rather than a Cycle Count.
    Is there any Firefox Employees reading this, and can acknowledge this has been added to their Opportunity (a.k.a. Bug) List?

  • APPHANGB1 when browsing the web, or just keeping it open. Happens once in a 5 minutes, and it freezes for 30 seconds. I found many people who have this problem too ....

    APPHANGB1 when browsing the web, or just keeping it open. Happens once in a 5 minutes, and it freezes for 30 seconds. I found many people who have this problem too ....

    Odds are only someone that develops apps for iOS would have access to whatever this is and, even then, this information may still not be available.
    I would do a backup of your phone & then erase it and restore from the backup to see if the odd behavior goes away. If so, something went funny with your update the first time around. If not, there's something in your backup that's making the phone throw a fit.
    I resolved my battery issues (more or less) by disabling the "set date/time automatically" setting. I haven't re-enabled it yet but my battery life has been much better with it off.
    ~Lyssa

  • 8800 GTS 512 OC - Runs in 3D for few minutes then freezes

    Hi there.
    I just got an 8800 GTS 512 OC, upgrading from a Radeon 1950 XT. The card works fine in 2D (it's in the machine as I type this). But when I try to play any game, it works fantastically for a few minutes (or seconds depending on how intensive the game is), and then freezes completely, with sound looping endlessly. I have to reboot to get out of it.
    I got the latest WHQL driver from Nvidia, 169.25, but that didn't help things. Oh, and don't worry, I removed the old ATI drivers and ran DriverClean Pro to remove any hidden remnants before I installed the card and drivers.
    I cannot use MSI Live Update, because as soon as I install it, I get a BSOD after rebooting:
    flashsys.sys,
    page fault in non-page area
    0x00000050 (0xBAB78000, 0x00000000, 0xBADF71B0, 0x00000000)
    Thinking it might be an OS issue, I then reformatted the system and ran a clean install of windows, but the same thing happened again. Makes me suspect that this is a hardware issue, since it seems the new WHQL driver is working jsut fine for other people.
    My system has worked fine until this card was installed, but here are my system specs for reference:
    System specs:
    E6600 at stock speed cooled by Zalman 9500 mod with Noctua 120mm fan
    Asus P5K-Deluxe, with P-ATA, Firewire, LAN og WLAN controllers disabled.
    2GB Corsair Dominator 8500 @ 1066 v/ 5-5-5-18, 2.2V
    Corsair HX-620W PSU (should be more than enough juice)
    D-Link DWL G510 PCI Wifi kontroller
    NEC Optiarc 7170 Sata II DVD burner
    Seagate Barracuda 7200.10 500MB Sata II (houses C: partition + E: storage)
    Old Maxtor 320GB Sata I (storage, D:)
    Gigabyte 3d Aurora case fans: 1x120mm front, 2x120mm back
    and of course:
    MSI 8800 GTS 512 OC, ved 730core 1944 mem, with Forceware 169.21 WHQL
    Running legit Windows XP Professional SP2, fully updated.
    other processes:
    ESET Smart Security
    Logitech SetPoint
    Soundmax panel for onboard sound
    The card also fails while testing with ATITool artifacts scanner. A worrying thing I have noticed is that the fan speed does not adjust as temperature increases. Instabilities while running ATITool start when the card hits around 75C, and gets worse and worse as it passes 80C. Fan still runs at same speed. Might be a fan controller issue, but this card should not be having problems at 75C-85C.
    I should specify, that it does not actually fail the artifact test...it just starts freezing, then going again, then freezing, then going again, until it freezes completely.
    I really do not know what to do next. I think my card is just plain faulty, so thinking of RMA. If anyone has any ideas or advice, please please help me out.
    Best regards,
    Mikkel.

    Quote from: BOSSKILLER on 23-December-07, 01:18:06
    Setup VGA mem. freq. to 1872Mhz and re-test.
    OK, I just tried out your suggestion, but sadly, the same thing happens. I should add that it does exactly the same thing when just running the 3D view
    Also that the card emits a high-pitch modulating whining noise (it is not bearing noise from the fan, it sounds more like a high-pitch capacitor buzz), is that supposed to be there?

  • HELP Some Songs play for a few seconds then automatically finish and freeze

    I have some songs that i added to my iTunes and they play fully there but when i transfer them to my ipod they play for like a minute and then they cut to the end and they freeze there please help me!! this has only happened since i got a video ipod on christmas

    Try This...
    Close All Open Apps...  Perform a Reset... Try again...
    Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
    http://support.apple.com/kb/ht1430
    Also consider Deleting any Apps you have Purchased / Downloaded but you now never use.

  • TS1717 Trying to download iTunes onto PC installed with windows vista. Download keeps getting to 99% with 1 second remaining and then freezes / does nothing? Any help appreciated.

    Trying to download itunes onto PC installed with windows vista. Download keeps getting to 99% with 1 second remaining and then freezes / does nothing? Any help appreciated.

    I solved the problem! The updates orignally were downloaded to the C: drive of the server. I've since moved them to the E: drive and for some reason the Content folder in IIS didn't change the file path to the new WSUScontent folder.
    The root cause for this was failing to use the UTILITY designed for this very purpose.
    I edited the virtual directory settings in IIS and was able to put the correct path in.
    You still need to use the UTILITY.. to fix all the other stuff you're still missing.
    In the %ProgramFiles%\Update Services\Tools folder...
    WSUSUTIL MOVECONTENT E:\WSUS E:\WSUS\MoveContent.LOG -SKIPCOPY
    This problem was caused by moving the WSUS updates to a different local drive.
    No. This problem was caused by IMPROPERLY moving the WSUS updates to a different local drive.
    Lawrence Garvin, M.S., MCSA, MCITP:EA, MCDBA
    SolarWinds Head Geek
    Microsoft MVP - Software Packaging, Deployment & Servicing (2005-2014)
    My MVP Profile: http://mvp.microsoft.com/en-us/mvp/Lawrence%20R%20Garvin-32101
    http://www.solarwinds.com/gotmicrosoft
    The views expressed on this post are mine and do not necessarily reflect the views of SolarWinds.

  • When I open itunes it freezes for a few seconds then says iTunes stopped working and closes down. I have tried downloading the latest version, both repair and remove and it still keeps happening

    When I open itunes it freezes for a few seconds then says iTunes stopped working and closes down. I have tried downloading the latest version, both repair and remove and it still keeps happening

    Tried the un-install and getting the same problem although it takes a bit longer before it crashes this time. Checked the problem report and it looks the same as the previous reports.
    Problem signature
    Problem Event Name:          APPCRASH
    Application Name:          iTunes.exe
    Application Version:          10.2.1.1
    Application Timestamp:          4d756476
    Fault Module Name:          MediaToolbox.dll
    Fault Module Version:          1.0.694.3
    Fault Module Timestamp:          4d4d9a00
    Exception Code:          c0000005
    Exception Offset:          0034a672
    OS Version:          6.0.6002.2.2.0.768.3
    Locale ID:          2057
    Additional Information 1:          fd00
    Additional Information 2:          ea6f5fe8924aaa756324d57f87834160
    Additional Information 3:          fd00
    Additional Information 4:          ea6f5fe8924aaa756324d57f87834160

  • Gaming apps freezes for few seconds , then resumes by itself or crashes sometimes ,after upgrading to iOS 8.3 on iphone 6

    Gaming apps freezes for few seconds , then resumes by itself or crashes sometimes ,after upgrading to iOS 8.3 on iphone 6

    Update: my phone's connecting to the WiFi again. I don't know what did the trick. I did nothing since reinstalling the software. It hadn't worked then, it is now. I tried connecting to my dad's phone's hotspot( he uses a Moto G), and it worked. I then tried connecting to the WiFi at a friend's house, and when I came back home, my phone was able to connect to my WiFi! Is it of any significance that my friend's router doesn't require a password? My issue has been resolved( for now; I hope I'm not counting my chickens before they've hatched). For anyone facing a similar issue, I suggest you try everything I did:
    1. Turn your router off for a minimum of 30 seconds, turn it back on and try connecting.
    2. Click on the WiFi network you are connected to, scroll to the bottom, tap "Renew Lease".
    3. Do a soft and hard reset.
    4. Reset network settings.
    5. Back your data up, erase all content from settings menu, restore from backup.
    6. Reinstall your software( put it in recovery mode).
    I am not sure which of the above worked for me. Make sure you try everything. If none of the above works, take it to a genius bar or an authorised service provider. Good luck! :)

  • HP ENVY lagging for 5 - 10 seconds, then resumes normally, only to lag again after 10 - 15 minutes

    Hello , I just recently bought an HP ENVY J110 , and whilst i was playing my Games, it lags 5 - 10 seconds, then resumes normally, only to lag again after 10 - 15 minutes . Can Anyone help me on this one, as ive searched the internet and didnt find anything Thanks in Advance, will be much appreciated! Cheers! 

    Hello Nikki1314,
    Welcome to the HP Forums!
    I understand your new computer lags when playing games. To assist you, please provide the following information:
    1. The computer's model number. If you require assistance locating this information, please reference this website: Guide to finding your product number
    2. The computer's operating system. If you require assistance locating this information, please reference this website to determine your Windows operating system.
    3. Have you installed any new hardware on this computer, before the issue appeared?
    4. Have you installed any new software or drivers on this computer, before the issue appeared?
    5. What games produce this lag?
    Mario
    I worked on behalf of HP.

  • Ipod Plays 2 seconds of a song, the freezes 3/4 seconds, then plays fine?!

    Basically ive got the latest firmware, my Ipod plays the two seconds at the start of any song.
    The thing then freezes for about 4 seconds!
    The ipod photo then continues to play the song quite happily?!
    It seems to do it every time i use it. Is it due to the amount of music I have on it (almost full / 30 gb)? I guess its not. Im lost .
    Any ideas??

    Yeah I had to restore it . Shame, had a lot of music that i now have to put back on. Oh well, problem solved .

  • When im texting and I magnify bubble to go back the bubble freezes for about 5 seconds then unfreezes

    I Have a 5s and when I'm texting and use magnify bubble to go back the bubble freezes for about 5 seconds then unfreezes- My iphone 4 did same thing and was able to fix but cannot remember how- Something about copy or paste I think- Thanks

    Hello, Dthoney. 
    Thank you for visiting Apple Support Communities.
    Try closing all opening applications and power cycle the device.  Once this is done test to see if the device becomes responsive.
    iOS: Force an app to close
    http://support.apple.com/kb/ht5137
    Turn your iOS device off and on (restart) and reset
    http://support.apple.com/kb/ht1430
    Cheers,
    Jason H.

Maybe you are looking for

  • How to create a parsys in an overlay

    Hi I am trying to create a dynamic header such that: User mouse overs a navigation header item and a div is overlayed underneath the navigation bar containing 3 columns of links for that particurlar section. This div also contains a 4th column that c

  • Targer URL not opening in New Window

    I have built a report with URLs. The report works well, but the Detail report is opening up in main window (overwriting master report containing URLs). I have checked the property 'Open Links in New Window' in Master report, but still the same. Does

  • OPC DataSocket error 42 in writing negative values

    I was playing around with OPC and using the DataSocket pallete. Although I've used it reliably for a while and am content, I was baffled by one error. I was hoping someone could explain why this error occurs or how to solve it. In the NI Distributed

  • White pixel on Macbook Pro 13" Retina

    I have a white pixel on my screen. Do I need to take it in or is there an easier way to fix it?

  • Searching PRODUCT column based upon user's input

    I have table in Oracle with one column PRODUCT. Column PRODUCT have following values - Account Management Active Directory NT Account Application Security Beehive Conference WebSite Account HP Laptop I am designing application where I need to search