-50 error when updating iphone???

Hi everyone,
I'm trying to update/back-up my iPhone 4 to the latest version. I've been sucessful in updating itunes, however, when I try to update my phone, the (-50 error message appears. It gives me the option to continue or cancel. It warns me that if I continue, it will delete all content. I'm concerned I will lose everything if I continue".
If anyone has any step by step information on how to fix , it would be greatly appreciated!
Thanks,
jamiefromon

If you have a backup stored in itunes you have nothing to worry about if not just right on you iphone under device and choose backup.
As far as the error message goes if you search that message (-50) on http://support.apple.com/kb/TS3694 it refers you to errors 13 and 14 which states
These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network.
Hope that works for you

Similar Messages

HT201210 Error when updating iPhone from 5.1.1 to iOS 6.0

When I tried to update my iPhone software from 5.1.1 to iOS6, it said there was an error. Then it said I needed to restore my iPhone. I pushed update and restore, and it keeps giving me an error. My iPhone is essentially wiped out and not usable because it shows iTunes with the cord logo on my phone. I've tried this several times to restore. What do I do?

http://support.apple.com/kb/TS3694#error3194

Error when updating iPhone software.

error: [There was a problem downloading the iPhone software for the iPhone "Eliz's iPhone". You do not have permission to access the requested resource.] I am trying to update iPhone to version 1.1.4 and I get the above error. I have reset the iPhone, restarted my computer, updated and repaired iTunes software (7.6.1.9)and nothing works. Has anybody else had this problem? Anybody know how to fix it?

Well I checked and all my USBs are 5.0 or higher. However, i have 4+ USB ports on the back of my computer. I tried two different ones and the second one allowed me to pull in my photos (which i could not do before). However, It still will not let me update the iPhone software. Same error - you do not have permission to access the selected resource.

IOS 7 Error when updating iphone 4 with new itunes account

Hi Guys, my phone is an Iphone 4, i tried creating a new itunes user account (as i was using my sons) then when i tried to peform an IOS7 update, it had an"upload Error" Message and i lost everything on my phone?

Take a look at this:
Errors related to third-party security software
Error 2, 4 (or -4), 6, 1000, 9006
Follow the steps to troubleshoot security software. Often, uninstalling third-party security software will resolve these errors.
There may be third-party software that modifies your default packet size in Windows by inserting a TcpWindowSize entry into your registry. An incorrectly set default packet size can cause these errors. Contact the manufacturer of the software that installed the packet size modification for assistance or follow this article by Microsoft: How to reset Internet Protocol (TCP/IP).
Verify that access to ports 80 and 443 are allowed on your network.
Verify that communication to albert.apple.com or phobos.apple.com isn't blocked by a firewall or other Internet security setting.
Discard the .ipsw file, open iTunes and attempt to download the update again. See the steps under "Advanced steps > Rename, move, or delete the iOS software file (.ipsw)" below for file locations.
Restore your device while connected to a different network.
Restore using a different computer.
From
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694#error6

Unknown error when updating iphone

I just tried installing the 7.0.3 update for my iPhone 4 and it came back with an unknown error message. Does this mean I have lost all of my pictures that I hadn't downloaded yet? I just synced my phone before I updated. It has some irreplaceable pictures I took of my kids.
Thanks.

Here:
The folder where your backup data are stored varies depending on the computer's operating system. Make sure the backup folder is included in your periodic data-backup routine.
iTunes places the backup files in the following places:
Mac: ~/Library/Application Support/MobileSync/Backup/
Note: The "~" represents your Home folder. If you don't see Library in your home folder, Option-click the Go menu.
Windows XP: \Documents and Settings\(username)\Application Data\Apple Computer\MobileSync\Backup\
Note: To quickly access the Application Data folder, click Start, and choose Run. Type %appdata% and click OK.
Windows Vista, Windows 7, and Windows 8: \Users\(username)\AppData\Roaming\Apple Computer\MobileSync\Backup\
Note: To quickly access the AppData folder, click Start. In the search bar, type %appdata% and press theReturn key.
If you find the photos, then restore.
Or, go to iTunes>iTunes Preferences (drop down menu)>Backup> and check to see if the backup is the most recent one. If there is no back up, then the photos might be gone if they are also not on your computer from any other methods.

Error 1602 when updating Iphone 4 from 4.3 to 5.. Any help ?

Error 1602 when updating Iphone 4 from 4.3 to 5 and after that it goes into "recovery mode" but Its not recognized by Itunes, I can only exit it with Tinyumrella and nothing else.

It seems that the itunes program has some interfefence when contacting the apple server.
i had this problem gave me error message 3200, i turned off the anti virus after restarting the computer(windows vista) and restarting the phone.
Turned off the sidebar, and closed any programs in the notifications section such as nokia ovi etc which load up when the computer starts also skype.
ha presto it began the process of transfering the file to the iphone4 and has now fully updated
hope that helps
leon

I get a -43 error when updating I tunes account

Every time I try to update to the newest iOS I get an error -43 during the backup phase. No explanation or any details.

Try here:
Error -43
Error code -43 when updating iphone 4 to new 5.0 software

Error 9 updating iphone 4 to ios4.3

Hi guys.. Anyone experienced error 9 when updating iphone 4 to ios 4.3? Any solutions? My phone is now useless because of this.. stuck in DFU and cannot do restore/recovery..

Did you check your security software settings? http://support.apple.com/kb/TS3125
Error 9: This error occurs when the device unexpectedly drops off of the USB bus and communication stops. This can occur if the device is manually disconnected during the restore process. This issue can be resolved by performing USB isolation troubleshooting, using a different USB dock connector cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.
copied from http://support.apple.com/kb/TS1275

HT2693 I am getting an 1015 error while updating Iphone 3G with latest iTunes pls help me to restore iPhone 3G

I am getting an 1015 error while updating Iphone 3G with latest iTunes pls help me to restore iPhone 3G

Try this and see if this helps http://support.apple.com/kb/TS3694#error1015

Error when updating Playbook OS version via Blackberry Desktop Manager

Greeting,
I have a batch of old playbooks which having the stack charging issue, but I found that I can update the OS to the newest version (2.1.0.1917) via Blackberry Desktop Manager, then the charging algorithm will be changed to the updated one and go over this dead battery issue. I was able to do so successfully in the past week smoothly on several devices.
But since this Monday, the Desktop Manager is saying "An updated Blackberry Desktop Software component must be installed before you can continue" when downloading the Desktop software and will appear "There was an error updating your software, an error has occurred while downloading the Blackberry Desktop Software.Please try again." and preventing the process. Seems there are some change on the server side starting this week which has caused this problem, but there's no error code to locate the exact issue.
I tried on 2 different computers as well as completed uninstalling and re-installing the Desktop manager, also tried to disable the automatic update as been advised in some threads. So no clue how to deal with it for now. It will be highly appreciate if some one can share some idea.
I've attached the step by step screenshots for reference, where you can find here:
http://forums.crackberry.com/blackberry-playbook-f222/error-when-updating-playbook-os-version-via-bl...
Thanks,

BLock wrote:
Sorry I can not help you with your problem but perhaps you can help me.
Can you advise where I can find info on "disable the automatic update"?
just ignore the update if you dont want it on the playbook
for reloading the OS
First I would like you to do a Back Up of your PlayBook using your computer and BlackBerry Desktop Software.
This can be downloaded for free from http://us.blackberry.com/apps-software/desktop/
After the Back Up is complete I need you to unplug your PlayBook and then push and hold down the Power Button until the unit Force Powers Off.
Now, while Desktop Software is still open on your computer and the PlayBook Powered Off, Connect the PlayBook to your computer.
You should see and error screen from Desktop Software pop up that has the options to Retry, Update, or Cancel.
QUICKLY choose the Update option.
This will erase all the information off of your PlayBook and Re-Write the Software back onto it. Once it's complete your PlayBook will need to go back through the setup wizard, and you can then perform a restore using Desktop Software to return your information. The only thing that won't come back after the restore are the apps that you downloaded from App World but they can be easily Re-Installed using the My World feature in App World.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Error Loading Hierarchy Error when updating Idocs in Source System

Hello Friends,
I am loading hierarchy data using Info pac into 0FUNDS_CTR . I have selected a hierarchy under hierarchy selections tab in the Info pac .
All Partner profiles in WE20 seems OK . But When I loaded data , throwing errrr message as below
Error when updating Idocs in Source System
Diagnosis
Errors have been reported in Source System during IDoc update:
System Response
Some IDocs have error status.
Procedure
Check the IDocs in Source System . You do this using the extraction monitor.
Error handling:
How you resolve the errors depends on the error message you get.
When I checked in TC WE05 says that IDoc: 0000000000355113 Status: Error during syntax check of IDoc (outbound) with status 26 .
Please advice .
Many thanks

Hi Krishna4bi,
Actually we will monitor idoc status in BD87 in SAP BI As well ECC , while extracting the data from source sytem if any idoc struck we will manually process in BD87 , But you are telling that while loading the datasource the error occurred , so please check once in ECC side . Otherwise see how many packets are still process, make it red that infopackage and do manually update.
Hope it helps,
By,
Praveen Yagnamurthy,
SAP BI Consultant,
Blue Marlin Systems-INDIA.
http://bluemarlinsys.com/bi.

Error when updating Idocs in Source System - Urgent

Hi Team,
When i was loading the data from SAP R/3 to BW, i was facing the error "Error when updating Idocs in Source System" (0 From 0 Records).
When i check in the Environment>Transaction RFC->In the Source System, it was displaying the error--
<b>" Import container contains errors (are any obligato) in the Function Module: IDOC_ERROR_WORKFLOW_START_R".</b>
Can any one please help me to solve this error.
This is am Urgent requirement for me to deliver.
Thanks & Best Regards,
Venkata.

Hello VenkaTa,
How r u ?
The workflow settings are not proper it seems. Ask the BASIS people to correct the Work Flow Settings. Then try Updating the IDOCs manually.
Also check the Inbound and outbound IDOCs in the Source system. The outbound should contain some warnings or errors.
Best Regards....
Sankar Kumar
+91 98403 47141

Error when updating Idocs in Source System

Hi All,
We did a recent copy from QAS to DEV,after which am unable to run my process chains ,the load status still showin yellow signal,whereas job is getting finished but am unable to load datas to the targets. Am getting the following error message when i see the display message in process chain.
System Response
Some IDocs have error status.
Procedure
Check the IDocs in Source System . You do this using the extraction monitor.
Error handling:
How you resolve the errors depends on the error message you get.
Error when updating Idocs in Source System
Could anyone please let me know what can be done ?
Thanks
con

Hello All,
I have same problem but its RESOLVED by the following process.
Step - 1
execute the Function module "SCP_LANGUAGES_IN_INSTANCE". It may or maynot give some output. Just note if it give the output
Step - 2
in Transaction SE38 execute the program "RSCPINST".
Just Click on the Activate button (dont select anything).
Step - 3
Again do the same thing specified in Step - 1. Now it will give the output saying that Language is DE.
So by the above procedure my issue is been resolved.
Regards
Sankar

Error when updating

I get an error when updating. The message states,
Adobe Photoshop Elements 12.1 update
There was an error installing this update. Please quit and try again later. Error Code: U44M1I200
Photoshop Camera Raw 8.5
There was an error downloading this update. Please quit and try again later. Error Code: U43M1U49
Do you know what causes this issue?

Please see- https://helpx.adobe.com/photoshop-elements/kb/elements-12-1-update-error.html
This error code occurs when multiple instances of Updater are open. Please refer to following forum link for more details: http://forums.adobe.com/message/4913117#4913117#4913117
Thanks
Andaleeb

Error when updating! Help please!!

I've been having a problem with the artwork updating on my 5th iPod. I kept getting an error when updating in iTunes whenever I added artwork to songs. So I was told to go into iTunes and go under iPod options and UNCHECK the box to display the artwork on my iPod. Then click okay. Then, go back into it and CHECK the box TO display the artwork and I get an error; "..Unknown Error occurred (-50)". Same error. And yes I have pressed the center button on my iPod to scroll through the different things. And I have restarted the program and computer. Tried disconnecting hte iPod, closing the program, restarting computer, restarting iTunes and reconnecting iPod and every combination of the steps (I've done many searches on this subject here) and same result. I've tried other different things but it all ends up to this error. Can some one please help me
Windows XP Pro

Hi Melophage,
I managed to do a OS X Recovery Reboot by restarting my computer and holding down Command and 'R'. I reinstalled OS X, and now my computer is working again.
However I'm going to take my computer into the Genius bar for review.
I have a Macbook Pro from 2012 (with a 2.6 GHz Intel Core i7 Processor) and was attempting to update OS X (I think Version 10.8.5).
Many thanks for your message.

-50 error when updating iphone???

Similar Messages

Maybe you are looking for