-50 unknown error during restore after download of 1.11

My unhacked I Phone gives me unknown error -50 during download and restore of new software. The phone has gone nuts. No hacks on phone. Travelling outside of the USA I cannot get service. Any suggestions?

Similar Messages

Was updating iPad to iOS 5. Received unknown error during restore. Didn't sync. Appears to be wiped out. Can anyone help? Thanks!

Was updating iPad to iOS 5. Got unknown error during restore. Now it appears to be wiped out. Screen just asks to be plugged into iTunes, which doesn't recognize thx iPad. Have rebooted both. Please help! Thanks.

See if anything on this page helps : http://support.apple.com/kb/ht4097 - it covers update and restore problems

Unknown Error during Recovery - iPad no longer Recognized by iTunes

I have a 3rd Generation iPad which I was attempting to perform a factory reset. I received an "Unknown Error" during the process and from that point on I have been unable to get iTunes to recognize my iPad in recovery mode (or otherwise).
I have tried every thread on the subject, but I found one interesting thing. If I connect the iPad with the same cable, etc. to another computer it immediately recognizes it in recovery mode and offers to restore the iPad.
It seems like my computer is not recognizing the iPad because it was in the process of restoring the device when the error occurred. Does anyone know if there is a way to reset or fix this issue. I would prefer not to update iTunes and download both the new iTunes and iPad software again and use another computer if it is not necessary.
Any help would be appreciated.
Thanks

Hey KSHItunes,
That was a good test to try your iPad on another computer. It does seem to isolate the issue to something with your computer setup.
Although you would prefer not to update iTunes, there may be steps in this article which can help.
iPhone, iPad, or iPod not recognized in iTunes for Windows - Apple Support
Please check it out.
Regards,
Nubz

Cannot update my iPad2 to 5.1 An unknown error message cancels the download process. Could you please inform me how to fix this issue? Thanks!

Cannot update my jail broken iPad2 & iPhone 4S to 5.1
An unknown error message cancels the download process. Could you please inform me how to fix this issue? What is also odd is the fact that the update through iTunes is substantially bigger than downloading it directly OTA, although both methods have been unsuccessful so far...
Thanks!

About the only thing you can try is using the Online Internet Recovery system to reinstall Lion on your Mac over the top of the current install. that will reset all system files and should not touch your personal files or the apps you have installed.
Or iof you have a recent Time Machine backup use that to restore your Mac to that point in time.

I keep getting unknown error when trying to download apps

Does anyone know why I keep getting unknown error when trying to download apps?

does it says anything else than unknow error?
try going to settings>store, click on apple id and then sign out. Restart iphone and sign back in and try downloading again

Getting error message -050 after downloading 11.1

Getting error message -050 after downloading 11.1, radio and match do not work.

What is the version of your OHS. Are you referring to 11gR2 webgate for OHS ?

TS3694 I cannot update my iPhone 3g to iOS 4.2.1 because of iTunes error 1015 ;error during restoring of firmware mode.

I cannot update my iPhone 3g to iOS 4.2.1 because of iTunes error 1015 ;error during restoring of firmware mode.

Was you iPhone jailbroken?

1: Unknown error during installation

Hi,
Where having problems with the process of Fixed Assets. We are adding datas in te ff: forms: Fixed Asset Master Data, Asset Classes, Account Determination and Fixed Asset Aquisition. The error appeared in the lover area in red color stating 1: Unknown error during installation
Please advise what to do.
Regards,
IAN

Hi
It is difficult to say but more looks like corrupt installation .You probably have to reinstall .
This thread might be of some help
Error Installing Fixed Assets
Start Fixed Assets Add-on Error
Thank you
Bishal

Nano 5 cannot by synced with unknown error 13019; can't download restore

I know there are variations on this problem, but I didn't see any quite like what I'm experiencing.
New Nano 5. Connected it to itunes it synced ok. The next time I attempted to resync, I got unknown error 13019 and it wouldn't sync. I reset the Nano, still got error. I attempted to restore it and the restore download timed out. Tried that at different times with same results. Can you download the restore from the apple web site rather than thru itunes, or is it limited to that? Any other suggestions.
Thanks

iTunes updated? iPod Nano 5th Gen firmware updated?
iPod nano (5th generation) - User Guide
Apple’s “How To” iPod/iTunes Videos
Pod troubleshooting basics and service FAQ
U.S. iPod and Mac technical support: 1-800-APL-CARE (1-800-275-2273)

Getting "Unknown Error has Occurred" After Project Server 2013 DB Restore

Hi All,
I have restored our content and pwa databases as per Microsoft's guide, one Project Web App works fine and the other has the error "An Unknown Error has Occurred" on the projects view and also when viewing Enterprise Project Types.
Another thing I have noticed is that only the Sys Admin has access to the project sites even though users have been added as admins etc.
We are patched to the December 2013 CU / Hotfix and I have also run the provided service scripts by Microsoft to go with the hotfix.
Any help on this would be greatly appreciated as we are looking to test SP1 and apply to our production environment.
Thanks in advance...

PowerShell has a command called. Test-SPContentDB.
Run the TEST-SPContentDB powershell command on database and see if it provides additional information.
Cheers
Michael Wharton, MVP, MBA, PMP, MCT, MCTS, MCSD, MCSE+I, MCDBA
Website http://www.WhartonComputer.com
Blog http://MyProjectExpert.com contains my field notes and SQL queries

Error during restore/recovery and 'open resetlogs'

Hello forum. I'm attempting to restore a database to a new host and have run into an error during the opening of the database (with resetlogs). The renaming of the datafiles, restore, switching of datafiles, and recovery are all done by an rman script, the contents of which are below:
# Restore production database to DR site using file system
# instead of ASM
run {
set newname for datafile 1 to '/opt/oracle/product/10gR2/oradata/DB01/system.dbf';
set newname for datafile 2 to '/opt/oracle/product/10gR2/oradata/DB01/undotbs1.dbf';
set newname for datafile 3 to '/opt/oracle/product/10gR2/oradata/DB01/sysaux.dbf';
set newname for datafile 4 to '/opt/oracle/product/10gR2/oradata/DB01/users.dbf';
set newname for datafile 5 to '/opt/oracle/product/10gR2/oradata/DB01/undotbs2.dbf';
set newname for datafile 6 to '/opt/oracle/product/10gR2/oradata/DB01/file1.dbf';
set newname for datafile 7 to '/opt/oracle/product/10gR2/oradata/DB01/file2.dbf';
restore database;
switch datafile all;
recover database;
I get the following output:
RMAN> @/home/oracle/scripts/rman_dr.rman
RMAN> # Restore production database to DR site using file system
2> # instead of ASM
3> #
4> run {
5> set newname for datafile 1 to '/opt/oracle/product/10gR2/oradata/DB01/system.dbf';
6> set newname for datafile 2 to '/opt/oracle/product/10gR2/oradata/DB01/undotbs1.dbf';
7> set newname for datafile 3 to '/opt/oracle/product/10gR2/oradata/DB01/sysaux.dbf';
8> set newname for datafile 4 to '/opt/oracle/product/10gR2/oradata/DB01/users.dbf';
9> set newname for datafile 5 to '/opt/oracle/product/10gR2/oradata/DB01/undotbs2.dbf';
10> set newname for datafile 6 to '/opt/oracle/product/10gR2/oradata/DB01/file1.dbf';
11> set newname for datafile 7 to '/opt/oracle/product/10gR2/oradata/DB01/file2.dbf';
12>
13> restore database;
14> switch datafile all;
15> recover database;
16> }
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
Starting restore at 03-JAN-08
Starting implicit crosscheck backup at 03-JAN-08
allocated channel: ORA_DISK_1
channel ORA_DISK_1: sid=156 devtype=DISK
Crosschecked 651 objects
Finished implicit crosscheck backup at 03-JAN-08
Starting implicit crosscheck copy at 03-JAN-08
using channel ORA_DISK_1
Crosschecked 1 objects
Finished implicit crosscheck copy at 03-JAN-08
searching for all files in the recovery area
cataloging files...
no files cataloged
using channel ORA_DISK_1
channel ORA_DISK_1: starting datafile backupset restore
channel ORA_DISK_1: specifying datafile(s) to restore from backup set
restoring datafile 00001 to /opt/oracle/product/10gR2/oradata/DB01/system.dbf
restoring datafile 00002 to /opt/oracle/product/10gR2/oradata/DB01/undotbs1.dbf
restoring datafile 00003 to /opt/oracle/product/10gR2/oradata/DB01/sysaux.dbf
restoring datafile 00004 to /opt/oracle/product/10gR2/oradata/DB01/users.dbf
restoring datafile 00005 to /opt/oracle/product/10gR2/oradata/DB01/undotbs2.dbf
restoring datafile 00006 to /opt/oracle/product/10gR2/oradata/DB01/file1.dbf
restoring datafile 00007 to /opt/oracle/product/10gR2/oradata/DB01/file2.dbfchannel ORA_DISK_1: reading from backup piece /ocfs2/remitpro/oracleBackups/tmp/rman_LV0_DB01.642899284.1.1.bus
channel ORA_DISK_1: restored backup piece 1
piece handle=/ocfs2/remitpro/oracleBackups/tmp/rman_LV0_DB01.642899284.1.1.bus tag=20080101_LV0_DB
channel ORA_DISK_1: restore complete, elapsed time: 01:22:28
Finished restore at 03-JAN-08
datafile 1 switched to datafile copy
input datafile copy recid=14 stamp=643049225 filename=/opt/oracle/product/10gR2/oradata/DB01/system.dbf
datafile 2 switched to datafile copy
input datafile copy recid=15 stamp=643049225 filename=/opt/oracle/product/10gR2/oradata/DB01/undotbs1.dbf
datafile 3 switched to datafile copy
input datafile copy recid=16 stamp=643049225 filename=/opt/oracle/product/10gR2/oradata/DB01/sysaux.dbf
datafile 4 switched to datafile copy
input datafile copy recid=17 stamp=643049225 filename=/opt/oracle/product/10gR2/oradata/DB01/users.dbf
datafile 5 switched to datafile copy
input datafile copy recid=18 stamp=643049225 filename=/opt/oracle/product/10gR2/oradata/DB01/undotbs2.dbf
datafile 6 switched to datafile copy
input datafile copy recid=19 stamp=643049225 filename=/opt/oracle/product/10gR2/oradata/DB01/file1.dbf
datafile 7 switched to datafile copy
input datafile copy recid=20 stamp=643049225 filename=/opt/oracle/product/10gR2/oradata/DB01/file2.dbf
Starting recover at 03-JAN-08
using channel ORA_DISK_1
starting media recovery
channel ORA_DISK_1: starting archive log restore to default destination
channel ORA_DISK_1: restoring archive log
archive log thread=2 sequence=1005
channel ORA_DISK_1: restoring archive log
archive log thread=1 sequence=1365
channel ORA_DISK_1: reading from backup piece /ocfs2/remitpro/oracleBackups/tmp/rman_LV0_DB01.642900444.1.1.bus
channel ORA_DISK_1: restored backup piece 1
piece handle=/ocfs2/remitpro/oracleBackups/tmp/rman_LV0_DB01.642900444.1.1.bus tag=20080101_LV0_DB
channel ORA_DISK_1: restore complete, elapsed time: 00:00:05
archive log filename=/opt/oracle/product/10gR2/db/flash_recovery_area/DB01/archivelog/2008_01_03/o1_mf_1_1365_3qtshnfv_.arc thread=1 sequence=1365
archive log filename=/opt/oracle/product/10gR2/db/flash_recovery_area/DB01/archivelog/2008_01_03/o1_mf_2_1005_3qtshncz_.arc thread=2 sequence=1005
channel default: deleting archive log(s)
archive log filename=/opt/oracle/product/10gR2/db/flash_recovery_area/DB01/archivelog/2008_01_03/o1_mf_1_1365_3qtshnfv_.arc recid=2418 stamp=643049236
unable to find archive log
archive log thread=1 sequence=1366
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of recover command at 01/03/2008 16:47:22
RMAN-06054: media recovery requesting unknown log: thread 1 seq 1366 lowscn 181804603
RMAN> **end-of-file**
I searched for a decription of the 06054 error, and found that if the archive logs weren't available, then to run "alter database open resetlogs;", which I did. Here's the output:
RMAN> alter database open resetlogs;
database opened
RMAN-06900: WARNING: unable to generate V$RMAN_STATUS or V$RMAN_OUTPUT row
RMAN-06901: WARNING: disabling update of the V$RMAN_STATUS and V$RMAN_OUTPUT rows
ORACLE error from target database:
ORA-06553: PLS-801: internal error [56319]
I've done all of this twice now, with the same result. I've googled PLS-801 and found more than a few instances of people getting this code, but not during a database open after a restore. Can anyone shed some light on what might have gone wrong? In the interest of brevity, I left out the rest of the restore process prior to running the database restore, but other than setting "compatible" and "db_recovery_file_dest_size", it was all by the book.
Thanks in advance.

Thanks for the reply Pierre.
I am not using RMAN Duplicate. Yes, the source of the backup is an RAC. The destination is a single server, with the DB on the filesystem. Here's an overview of of the commands I ran and the procedure.
Copied tar'd backup controlfile and datafiles to destination machine. Untar'd. Install 10.2.0.1.0 on destination machine, patch to 10.2.0.2.0.
OS> sqlplus /nologin
SQL> alter system set compatible = '10.2.0.2.0' scope=spfile;
SQL> alter system set db_recovery_dest_file_size = '8g'; scope spfile;
SQL> shutdown immediate;
SQL> startup; (to verify changes took...)
SQL> shutdown immediate;
OS> Copy control file from untar'd dir and place in $ORACLE_HOME/dbs/, truncate name to c-DBID-date-00.
OS> rman target /
RMAN> startup nomount;
RMAN> set dbid <dbid from control file>;
RMAN> restore controlfile from autobackup; (finds control file with no problem...)
RMAN> alter database mount;
RMAN> @/home/oracle/rman_dr.rman (script cited in first post, to rename datafiles from ASM to filesystem, restore, switch files, and recover...)
RMAN> alter database open resetlogs; (as cited before...)
If I'm not using Duplicate and not specifying dates, the UNTIL/SET UNTIL commands aren't necessary, correct?

"An unknown error occurred (-50)" after library import

Here's the gist...
I used the new feature in File:Library to reorganize my iTunes 9 library so it was easier to navigate in Finder. After that, every time I plugged the iPhone in, it wanted to copy ALL the songs over again. I tried everything I could think of, including restoring my phone. When all that failed, I followed the advice of a KB Article (http://support.apple.com/kb/HT1451) and, lo, the problem was solved.
...until I went to check for updated apps. All my iPhone apps still exist in the Mobile Applications folder in Finder, but none are present in iTunes. Any attempt to add them via drag and drop results in the error "The Application (name) could not be added to your iTunes library because an error occurred. An unknown error occurred (-50)." I also discovered that app syncing had been turned off in the iPhone settings.
With there being 121 apps in that folder, I'm certainly in no mood to redownload them all and telling iTunes to just sync apps again results in it wanting to wipe my iPhone of all the installed apps. Also not something I'm willing to do.
Any thoughts?
thanks!
dennis
Message was edited by: Dennis Alaniz2

Thanks, MJ, but that's not the problem I'm having. I can see the apps in finder, I just can't get them back into iTunes where they belong.
As further clarification to my problem, a post was created in the iPhone Hardware group where someone else is having the same problem I was (http://discussions.apple.com/thread.jspa?messageID=10236133#10236133) in conjunction with the problems listed above. By following the advice of the KB article, that problem, and the continuous copying of songs, was solved, but the missing applications problem was then created.
I'm cross referencing this post with that one so that the problem can be hit at both ends and people can be made aware of the greater scope of this issue.
dennis
Message was edited by: Dennis Alaniz2

Help! Unknown Error -50 -- Can't Download Music

Does anybody know what "unknown error -50" is? I tried to buy some music and it stalls, then gives me the pop-up window saying:
"There was a problem downloading ___. An unknown error occurred (-50). Please check that the connection to the network is active and try again."
I am active, and it doesn't work. Thanks.
Happened on my PowerBook G4, using iTunes 7.01.

PToe,
Thanks. I had exactly the same problem. Restarting iTunes as you perscribed took care of things.
I have not had this problem on my iMac (where I have been running iTunes 7.0.1 for over a week and have bought lots of music since upgrading), but the "unknown error -50" happened on my PowerBook after upgrading to iTunes 7.0.1 from 6.something two days ago. The only differences between the two systems are (a) the PowerBook is connected wirelessly to my router (the iMac is wired to the router), and (b) I am running 10.3.9 on the Powerbook vs. 10.4.8 on the iMac.
It would be nice to know why this error happened.
Tom
iMac G4 1.25GHz Mac OS X (10.4.8) PowerBook 15" Titanium 10.3.9

Unknown error -1 restore-error in iTunes, does anyone has a solution?

Hello
After the Battery was empty, the iPhone gave a Message activiation needed. After that a restore was needed. After i tried to restore i tot the message unknown error (-1).

Perhaps try the Error 1 or -1 advice from the following document:
iTunes: Specific update-and-restore error messages and advanced troubleshooting

Unknown errors during manual software update package installation

Hi,
I'm new to the forum.
Recently I've got a serious trouble while installing standalone update packages from disk image files.
After typing my username and password to update my OS manually my computer suddenly fails to install the software packages saying that "the installer has encountered an unknown error which caused the installation to fail."
I've an early 2009 Mac Mini which I bought during the first half of that year. The problem affects all versions of Mac OS X (10.5 and later). It's normal? I've tried everything (permissions repair, SMART check) to fix the problem with no luck. Now I suspect the issue has something else with bad memory or a faulty hard disk.
How curious, System Graph had put a new Super Drive on it because the original had its laser head damaged due to extensive use.
Cheers,
John

FIXED!
Many DMG executables failed to install because their certificates were outdated.
To resolve the problem: uncheck the automatic time setting box and set the clock to an early date.

-50 unknown error during restore after download of 1.11

Similar Messages

Maybe you are looking for