5505 Strange vpn problem I can only connect if the pc has a WAN IP addess

I have a asa5505 if an outside computer has a wan ip address it will see the computers on the network. If the computer is behind a router (any router) it will connect fine but will not see any computers on the network. All computer on the in the vpn are a 10.1.1.0 network and the connecting computers are on a 192.168.1.0 network. All subnet mask are 255.255.255.0. Thanks in advance.

Add the following command to your ASA.
crypto isakmp nat-traversal
In ASDM, it would be located as a checkbox "Enable NAT-T" located under config -> vpn -> ipsec -> ipsec rules -> select the dynamic entry -> Tunnel Policy advanced tab -> enable nat-t
This will allow users behind pat devices to use nat-t and should solve your problem.
Please rate if it helps.

Similar Messages

  • I have a ipad2 and can only connect to the internet on safari but not any WiFi related apps such as YouTube or Facebook. plz help.

    i have a ipad2 and can only connect to the internet on safari but not any WiFi related apps such as YouTube or Facebook. plz help.

    Try changing the channel in use in case you're getting interference. 
    If you have WEP enabled on the Internet Sharing it'ss worth disabling it whilst troubleshooting the connectivity issues.
    mrtotes

  • 18 month old original i-pad switches on but screen resolution not good and can only just see the icons has the screen gone?

    18 month old original i-pad switches on but screen resolution not good and can only just see the icons has the screen gone?

    No could just make this out and it is up full

  • WRT45G: can only connect one pc at the time to internet, cannot login to router setup

    Hello,
    I don't get this. The complete network worked fine for ... years? After a call with the ISP about a general/different issue, we can now only connect one pc at the time to internet. (We were asked to take out cables and we've put them back).
    I've been trying and searching for an answer for hours.
    problem:
    We can only connect through the router to internet with only one pc at the time (the first pc we connect after starting up the router).
    Also we cannot get into the setup menu of the router at 192.168.1.1
    We've been trying to reset the modem for 10, 30 seconds.
    Auto resolve IP/DNS. DHCP is enabled.
    I also remembered that I pushed the SES button, it turned from orange to flashing bluish. I never knew aboutthis function, nor it is mentioned in the manual I downloaded. Now this SES indicator is off.
    Also WLAN and DMZ led are off.
    I downloaded EasyLink_Connect.exe, went through the setup. It recognises there's internet connection, but stops and says: cisco does not support this modem.
    Temp. replacing this WRT45G modem with another one did not resolve the issue.
    I have no clue what went wrong, what we did wrong, and how we can resolve this issue? Please help! Thanks
    Message Edited by Brammm on 11-27-2008 03:13 PM

    Okay! 
    1.  (results when having assigned a static IP) :
     Windows IP-configuratie
             Primair DNS-achtervoegsel. . . . .:
            Knooppunttype: . . . . . . . . . .: onbekend     (unknown)
            IP-routering ingeschakeld. . . . .: nee      (no)
            WINS-proxy ingeschakeld . . . . . : nee    (no)
     Ethernet-adapter LAN-verbinding:
             Verbindingsspec. DNS-achtervoegsel:
            Beschrijving . . . . . . . . . . .:
              VIA Compatable Fast Ethernet Adapter
            Fysiek adres. . . . . . . . . . . : 00-16-17-CE-D5-40
            DHCP ingeschakeld:. . . . . . . . : nee    (no)
            IP-adres. . . . . . . . . . . . . : 192.168.1.20
            Subnetmasker. . . . . . . . . . . : 255.255.255.0
            Standaardgateway. . . . . . . . . : 192.168.1.1
            DNS-servers . . . . . . . . . . . : 192.168.1.1
     (results without having assigned a static IP: automatic config.) :  
     Ethernet-adapter LAN-verbinding: 
            Verbindingsspec. DNS-achtervoegsel:
            Beschrijving . . . . . . . . . . .:
              VIA Compatable Fast Ethernet Adapter
            Fysiek adres. . . . . . . . . . . : 00-16-17-CE-D5-40
            DHCP ingeshakeld. . . . . . . . . : ja     (yes)
            Autom. configuratie ingeschakeld. : ja       (yes)
            IP-adres. . . . . . . . . . . . . : 84.30.99.32       
    Subnetmasker. . . . . . . . . . . : 255.255.254.0       
    Standaardgateway. . . . . . . . . : 84.30.98.1       
    DHCP-server . . . . . . . . . . . : 213.51.144.90
            DNS-servers . . . . . . . . . . . : 212.54.40.25
                                                212.54.35.25
    2.  I do have another router, when I try that one, the problem we have remains. So that's a bit strange to me. That one is supposed to be working.
    Does this SES function configure anything other than the modem? So, does it alter PC configurations? I have no clue.   We even start to wonder whether the ISP is able to set up their internet in a way that unables us to make use of a router? That would be ridiculous
    Message Edited by Brammm on 11-30-2008 04:03 AM

  • Can only connect to Internet from one computer at a time on network

    I have a 2 computer network in my office networked with an Asante 10/100 hub. The computers are a iMac 24 (Intel) and an old G4 (PCI). The network has worked fine until just recently. Now, I can only connect to the Internet with one computer at a time...(DSL connection). I checked cables, ports, etc, and I'm wondering if this is a 10.4.9 issue. Coincidentally, I noticed that I am not able to access the Internet via Win XP using Parallels which also worked fine up until recently. I checked with the ISP (AT&T) who confirmed that all is OK on their end. Anyone have similar problem? Could OS X 10.4.9 be the culprit? Any help on this will be much appreciated. Thanks.
    iMac 24   Mac OS X (10.4.9)   2G RAM; NVIDIA GeForce 7600 GT 256

    I'd consider that a 3 computer network, Parallels being a virtual machine would alias the ethernet interface and need its own IP address. That may or may not have anything to do with your problem. Actually, the way you've described things, it sounds like a lot has to do with your contract with ATT. Is there a routing device at your end?
    The only way 10.4.9 could be the culprit would be if it were the routing device.
    -Phil

  • Devices can only connect to airport exp b4 Macbook

    I hope someone can help:
    I have a Macbook and Windows XP machine both successfully connected to my Airport Express Wi-fi network. But I also have a Nokia mobile phone (Symbian OS) and Dell Axim PDA (Windows Mobile) which I would like to connect. These devices can connect to every other network I have tried but can only connect to the Airport Express network if I connect them before the Macbook is connected (they remain connected if I then connect the Macbook too). If I try to connect them after the Macbook has connected, they don't even see the network! The Windows XP machine is unaffected by any of this.
    Any help much appreciated!
    Keith

    In case anyone else has this issue, I think I worked it out:
    The Airport Express WLAN port was set to "automatic" but changing it to "1" allows the mobile devices to access the network even after the macbook. Dunno what the macbook was up to though....

  • Can only connect one user at a time via VPN?

    Hi, long-term Mac user but new to OS X Server. Dug thru the forums quite a bit but couldn't find an answer to this one - hopefully I wasn't searching with the wrong keywords.
    Installed OS X Server 10.6 on a MacBook (white, 1 generation back) at the office. Sits behind an Airport Extreme, which is connected to Comcast. Other machines at the office are NOT routed through the Server, but rather connect directly to the Airport Extreme for internet access. I've set up server.mydomainname.com to point to our Comcast address, and I am able to connect via VPN to the server without any problems, and access the server using the server.mydomainname.com address which I pointed to my Comcast IP address, as long as I check "Send all traffic over VPN connection" on my client.
    However, when I'm logged in via VPN on one computer, and then log in via VPN on another computer (with the same UID or a different one), the first one loses all connectivity through the VPN - it's as if it had been logged off.
    In Server Admin, under the Settings|Network tabs, I have Computer Name set up as "theserver", and Local Hostname as "theserver" (so I can access via theserver.private). VPN is set up to enable L2TP over IPsec, sharing ranges 10.0.1.200 thru 10.0.1.220; no load balancing, no PPTP. Client DNS servers is set to 10.0.1.29.
    Any ideas as to why I can only connect with one client at a time?

    Thanks. I didn't see anything interesting, but then again I'm not up on VPN details. Here's the scenario:
    First, I logged in as "user1", and I can use the VPN.
    Then, I logged in as "user2", and I can use the VPN with user2, but user1 is no longer able to do anything over the VPN.
    Then I hung up with user2, but user1 still can't see anything over the VPN.
    Then I hung up and reconnected with user1, and user1 can use the VPN again.
    Here's part of the log for this activity. I've replaced potentially identifying info with "XYZ" for safety. Appreciate any thoughts on this!
    Tue Oct 19 07:33:08 2010 : L2TP received ICCN
    Tue Oct 19 07:33:08 2010 : L2TP connection established.
    Tue Oct 19 07:33:08 2010 : using link 1
    Tue Oct 19 07:33:08 2010 : Using interface ppp1
    Tue Oct 19 07:33:08 2010 : Connect: ppp1 <--> socket[34:18]
    Tue Oct 19 07:33:08 2010 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:08 2010 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:08 2010 : lcp_reqci: returning CONFACK.
    Tue Oct 19 07:33:08 2010 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:08 2010 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:08 2010 : sent [LCP EchoReq id=0x0 magic=XYZ]
    Tue Oct 19 07:33:08 2010 : sent [CHAP Challenge id=0x18 <XYZ>, name = "myserver.private"]
    Tue Oct 19 07:33:08 2010 : rcvd [LCP EchoReq id=0x0 magic=XYZ]
    Tue Oct 19 07:33:08 2010 : sent [LCP EchoRep id=0x0 magic=XYZ]
    Tue Oct 19 07:33:08 2010 : rcvd [LCP EchoRep id=0x0 magic=XYZ]
    Tue Oct 19 07:33:08 2010 : rcvd [CHAP Response id=0x18 <XYZ>, name = "user2"]
    Tue Oct 19 07:33:08 2010 : sent [CHAP Success id=0x18 "S=XYZ M=Access granted"]
    Tue Oct 19 07:33:08 2010 : CHAP peer authentication succeeded for user2
    Tue Oct 19 07:33:08 2010 : DSAccessControl plugin: User 'user2' authorized for access
    Tue Oct 19 07:33:08 2010 : sent [IPCP ConfReq id=0x1 <addr 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfReq id=0x1]
    Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
    Tue Oct 19 07:33:08 2010 : ipcp: returning Configure-NAK
    Tue Oct 19 07:33:08 2010 : sent [IPCP ConfNak id=0x1 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : rcvd [IPV6CP ConfReq id=0x1 <addr XYZ>]
    Tue Oct 19 07:33:08 2010 : Unsupported protocol 0x8057 received
    Tue Oct 19 07:33:08 2010 : sent [LCP ProtRej id=0x2 80 47 01 01 00 0f 01 0a 02 1b 63 ff fe a0 dd da]
    Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfReq id=0x1 <ms-dns1 0.0.0.1> <ms-dns1 0.0.0.1>]
    Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfRej id=0x1 <ms-dns1 0.0.0.1>]
    Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfAck id=0x1 <addr 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfAck id=0x1]
    Tue Oct 19 07:33:08 2010 : rcvd [IPCP ConfReq id=0x2 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : ipcp: returning Configure-ACK
    Tue Oct 19 07:33:08 2010 : sent [IPCP ConfAck id=0x2 <addr 10.0.1.213> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:33:08 2010 : ipcp: up
    Tue Oct 19 07:33:08 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
    Tue Oct 19 07:33:08 2010 : found interface en0 for proxy arp
    Tue Oct 19 07:33:08 2010 : local IP address 10.0.1.29
    Tue Oct 19 07:33:08 2010 : remote IP address 10.0.1.213
    Tue Oct 19 07:33:08 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
    Tue Oct 19 07:33:08 2010 : rcvd [ACSCP ConfReq id=0x2 <ms-dns1 0.0.0.1>]
    Tue Oct 19 07:33:08 2010 : sent [ACSCP ConfAck id=0x2 <ms-dns1 0.0.0.1>]
    Tue Oct 19 07:33:08 2010 : sent [ACSP data <payload len 26, packet seq 0, CI_DOMAINS, flags: START END REQUIRE-ACK>
    <domain: name XYZ>]
    Tue Oct 19 07:33:08 2010 : rcvd [IP data <src addr 10.0.1.213> <dst addr 255.255.255.255> <BOOTP Request> <type INFORM> <client id 0x08000000010000> <parameters = 0x6 0x2c 0x2b 0x1 0xf9 0xf>]
    Tue Oct 19 07:33:08 2010 : sent [IP data <src addr 10.0.1.29> <dst addr 10.0.1.213> <BOOTP Reply> <type ACK> <server id 0x0a00011d> <domain name "XYZ">]
    Tue Oct 19 07:33:08 2010 : rcvd [ACSP data <payload len 0, packet seq 0, CI_DOMAINS, flags: ACK>]
    Tue Oct 19 07:33:34 2010 : rcvd [LCP TermReq id=0x2 "User request"]
    Tue Oct 19 07:33:34 2010 : LCP terminated by peer (User request)
    Tue Oct 19 07:33:34 2010 : ipcp: down
    Tue Oct 19 07:33:34 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
    Tue Oct 19 07:33:34 2010 : sent [LCP TermAck id=0x2]
    Tue Oct 19 07:33:34 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp1, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.213).
    Tue Oct 19 07:33:34 2010 : L2TP received CDN
    Tue Oct 19 07:33:34 2010 : Connection terminated.
    Tue Oct 19 07:33:34 2010 : Connect time 0.5 minutes.
    Tue Oct 19 07:33:34 2010 : Sent 777000 bytes, received 105388 bytes.
    Tue Oct 19 07:33:34 2010 : L2TP disconnecting...
    Tue Oct 19 07:33:34 2010 : L2TP disconnected
    2010-10-19 07:33:34 PDT --> Client with address = 10.0.1.213 has hungup
    Tue Oct 19 07:33:50 2010 : rcvd [LCP TermReq id=0x3 "User request"]
    Tue Oct 19 07:33:50 2010 : LCP terminated by peer (User request)
    Tue Oct 19 07:33:50 2010 : ipcp: down
    Tue Oct 19 07:33:50 2010 : sent [LCP TermAck id=0x3]
    Tue Oct 19 07:33:50 2010 : l2tpwaitinput: Address deleted. previous interface setting (name: en0, address: 10.0.1.29), deleted interface setting (name: ppp0, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.214).
    Tue Oct 19 07:33:50 2010 : L2TP received CDN
    Tue Oct 19 07:33:50 2010 : Connection terminated.
    Tue Oct 19 07:33:50 2010 : Connect time 3.5 minutes.
    Tue Oct 19 07:33:50 2010 : Sent 625383 bytes, received 225586 bytes.
    Tue Oct 19 07:33:50 2010 : L2TP disconnecting...
    Tue Oct 19 07:33:50 2010 : L2TP disconnected
    2010-10-19 07:33:50 PDT --> Client with address = 10.0.1.214 has hungup
    2010-10-19 07:33:59 PDT Incoming call... Address given to client = 10.0.1.216
    Tue Oct 19 07:33:59 2010 : Directory Services Authentication plugin initialized
    Tue Oct 19 07:33:59 2010 : Directory Services Authorization plugin initialized
    Tue Oct 19 07:33:59 2010 : L2TP incoming call in progress from 'XYZ'...
    Tue Oct 19 07:33:59 2010 : L2TP received SCCRQ
    Tue Oct 19 07:33:59 2010 : L2TP sent SCCRP
    Tue Oct 19 07:33:59 2010 : L2TP received SCCCN
    Tue Oct 19 07:33:59 2010 : L2TP received ICRQ
    Tue Oct 19 07:33:59 2010 : L2TP sent ICRP
    Tue Oct 19 07:33:59 2010 : L2TP received ICCN
    Tue Oct 19 07:33:59 2010 : L2TP connection established.
    Tue Oct 19 07:33:59 2010 : using link 0
    Tue Oct 19 07:33:59 2010 : Using interface ppp0
    Tue Oct 19 07:33:59 2010 : Connect: ppp0 <--> socket[34:18]
    Tue Oct 19 07:33:59 2010 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:59 2010 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:59 2010 : lcp_reqci: returning CONFACK.
    Tue Oct 19 07:33:59 2010 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:59 2010 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic XYZ> <pcomp> <accomp>]
    Tue Oct 19 07:33:59 2010 : sent [LCP EchoReq id=0x0 magic=XYZ]
    Tue Oct 19 07:33:59 2010 : sent [CHAP Challenge id=0xf1 <XYZ>, name = "myserver.private"]
    Tue Oct 19 07:33:59 2010 : rcvd [LCP EchoReq id=0x0 magic=XYZ]
    Tue Oct 19 07:33:59 2010 : sent [LCP EchoRep id=0x0 magic=XYZ]
    Tue Oct 19 07:33:59 2010 : rcvd [LCP EchoRep id=0x0 magic=XYZ]
    Tue Oct 19 07:33:59 2010 : rcvd [CHAP Response id=0xf1 <XYZ>, name = "user1"]
    Tue Oct 19 07:34:00 2010 : sent [CHAP Success id=0xf1 "S=XYZ M=Access granted"]
    Tue Oct 19 07:34:00 2010 : CHAP peer authentication succeeded for user1
    Tue Oct 19 07:34:00 2010 : DSAccessControl plugin: User 'user1' authorized for access
    Tue Oct 19 07:34:00 2010 : sent [IPCP ConfReq id=0x1 <addr 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : sent [ACSCP ConfReq id=0x1]
    Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns3 0.0.0.0>]
    Tue Oct 19 07:34:00 2010 : ipcp: returning Configure-NAK
    Tue Oct 19 07:34:00 2010 : sent [IPCP ConfNak id=0x1 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : rcvd [IPV6CP ConfReq id=0x1 <addr XYZ>]
    Tue Oct 19 07:34:00 2010 : Unsupported protocol 0x8057 received
    Tue Oct 19 07:34:00 2010 : sent [LCP ProtRej id=0x2 80 57 01 01 00 0e 01 0a 02 1b 63 ff fe 99 35 cb]
    Tue Oct 19 07:34:00 2010 : rcvd [LCP ProtRej id=0x2 82 35 01 01 00 04]
    Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfAck id=0x1 <addr 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : rcvd [IPCP ConfReq id=0x2 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : ipcp: returning Configure-ACK
    Tue Oct 19 07:34:00 2010 : sent [IPCP ConfAck id=0x2 <addr 10.0.1.216> <ms-dns1 10.0.1.29> <ms-dns3 10.0.1.29>]
    Tue Oct 19 07:34:00 2010 : ipcp: up
    Tue Oct 19 07:34:00 2010 : found interface en0 for proxy arp
    Tue Oct 19 07:34:00 2010 : local IP address 10.0.1.29
    Tue Oct 19 07:34:00 2010 : remote IP address 10.0.1.216
    Tue Oct 19 07:34:00 2010 : l2tpwaitinput: Address added. previous interface setting (name: en0, address: 10.0.1.29), current interface setting (name: ppp0, family: PPP, address: 10.0.1.29, subnet: 255.0.0.0, destination: 10.0.1.216).
    Tue Oct 19 07:34:00 2010 : rcvd [IP data <src addr 10.0.1.216> <dst addr 255.255.255.255> <BOOTP Request> <type INFORM> <client id 0x08000000010000> <parameters = 0x6 0x2c 0x2b 0x1 0xf9 0xf>]
    Tue Oct 19 07:34:00 2010 : sent [IP data <src addr 10.0.1.29> <dst addr 10.0.1.216> <BOOTP Reply> <type ACK> <server id 0x0a00011d> <domain name "XYZ">]

  • New problem - can only connect w/o security

    have a wireless router and had no problem getting my macbook to connect. added a desktop and can only connect if i disable the password feature. my question is twofold:
    1. why will it not connect when I have to supply a password (the password is correct)
    2. if I cannot resolve issue 1, then can I diable SSID broadcast but still not require a password?

    Try to include a dollar sign before your password

  • Users can only connect to RD farm website and cannot remote into terminal server , when connected via VPN

    Hello,
    I have a RD farm using 3 Win 2012 servers (1 broker and 2 session host), for internal use only, have not
    configured gateway for internet access.
    Users are able to connect to RD farm website and remote into terminal server, within office
    but can only connect to RD farm website and cannot remote into terminal server , when connected via VPN
    Its takes long time at securing connection and fails.
    Thanks

    Hi,
    Thank you for your posting in Windows Server Forum.
    First of all I would suggest you to configure RD gateway role on your server and pass all the connection through it because it’s a best practice to use RD Gateway in RDS Farm. 
    Apart from this, if you are not using RD Gateway then you must check that you have successfully forwarded port 3389 for RDS to access via VPN. Also check that you have made configuration under IIS Manager to enable Forms Authentication. Please check
    this link.
    In addition, please refer beneath article for additional details.
    1. How to Access Windows Remote Desktop Over the Internet
    2. Remote Desktop Services in Windows 2008 R2 – Part 3 – RD Web Access & RemoteApp
    (For reference)
    Hope it helps! 
    Thanks,
    Dharmesh

  • Can only connect to enterprise wifi the first time each day, then does not reconnect and got the "Associati​on Failed" error

    To save battery, I leave my wifi off when the TP's screen is locked.  At home, my TP has no problem reconnecting to wifi after the screen is unlocked.  However, at work, which uses enterprise wifi, I can only connect the first time.  If I lock the screen and then unlock it (causing the wifi to turn off and on again) then the TP will not reconnect and I would get the "Association failed" error over and over again.  If I were to turn the TP off and on again, I would still get the same error.  Here's the strange part, if I come in work the next day, it would be able to connect to the wifi.  If I were to leave the wifi on all the time, it would not disconnect even if I lock the screen.  Now if I were to turn off the wifi and then turn it on again, the TP would not reconnect.  So it seems like the TP can only connect the first time each day....very strange...and frustrating.
    Post relates to: HP TouchPad (WiFi)

    Scimmia is right.  But you AcousticBruce are still very wrong.  You claim there were no error messages.  Yet after much proding and denial you finally provide small portions of error messages which fully identify the problem and can be found in many other posts in these forums.  Yet still, you haven't actually provided full output - instead you paraphrased the output after a couple of "//" symbols.
    If you don't give us the actual output we can't help - except in this case the error is so common we could very easily help.  So could the wiki page on wpa_supplicant if you had read it, as your problem is explictly listed there in a "NOTE" box.  But more importantly if you are reluctant to give us actual output we will not want to help you.
    This issue would have been solved instantly if you would have provided the actual output instead of lying about it.
    The relevant wiki pages:
    https://wiki.archlinux.org/index.php/WP … passphrase
    https://wiki.archlinux.org/index.php/He … er_or_root
    And the related forums posts found after just a quick search of that error message that you finally provided:
    https://bbs.archlinux.org/viewtopic.php?id=167244
    https://bbs.archlinux.org/viewtopic.php?id=184824
    https://bbs.archlinux.org/viewtopic.php?id=178909
    https://bbs.archlinux.org/viewtopic.php?id=190097
    https://bbs.archlinux.org/viewtopic.php?id=191351
    https://bbs.archlinux.org/viewtopic.php?id=191964
    Last edited by Trilby (2015-05-18 11:08:44)

  • HT4199 Every time I introduce the WPA2 passwords I can´t connect. I can only connect to open wi fi networks? Does anyone know why? Thanks

    Every time I introduce the WPA2 passwords I can´t connect. I can only connect to open wi fi networks? Does anyone know why? Thanks

    Some users with various Wi-Fi connection problems have reported that they were given the following instructions by Apple Support, sometimes with success. I can't vouch for this procedure myself. After completing the procedure, you'll have to recreate all your settings in the Network preference pane. Make sure you know how to do that before you begin. Taking screenshots of the preference pane may be helpful.
    Step 1
    Back up all data.
    Triple-click the line below on this page to select it:
    /Library/Preferences/SystemConfiguration
    Right-click or control-click the highlighted line and select
    Services ▹ Reveal
    from the contextual menu.* A folder should open with an item named "SystemConfiguration" selected. Move the selected item to the Trash. You may be prompted for your administrator password.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard (command-C). In the Finder, select
    Go ▹ Go to Folder...
    from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
    Step 2
    Reset the System Management Controller

  • Can not connect to the internet. This is a new problem since I have been using firefox for years.

    I can not connect to the internet. I called mediacom due to the problem and they connected me to internet explorer. They indicated I should contact you for help in connecting to the internet. It appears firefox has made some kind of change since last night since I was using firefox for my internet connection last night. Something has changed. Your help will be appreciated.

    http://en.wikipedia.org/wiki/Keyhole_Markup_Language
    The only way that file opens thru IE8 for me ''(but not actually in IE8)'' is by using the Zip Utility (then IE closes) that is in WinXP and then opening the two image files in the Windows Fax and Picture Viewer.
    I think Firefox is trying to display that file because the MIME-type is for '''''text/plain''''' instead of the appropriate MIME-type of '''application/vnd.google-earth.kml+xml''' or '''application/vnd.google-earth.kmz'''
    That is something that needs to be configured in the server that is hosting that file type. Sorry, I don't know how that can be fixed. The one support person here that might know lives in Europe ''(I believe)'', so you might need to wait for an answer.

  • Can only connect from one direction

    I'm having trouble video confrencing... I tried searching the forums, but I'm having trouble thinking of clever search terms.
    I can only connect from one direction with one person. They can invite me to a chat and it works fine every time. However when I invite them it always fails. I can invite other people and it works fine though.
    This doesn't seem like a typical router problem, because they can invite me and we videochat just fine.
    This has been a problem for most versions of iChat that I can remember, but I'm using 3.1.5 currently.

    Hi
    Is the other person a PC user.
    Tony

  • Strange email problem; it started only loading unread emails, but from 3 months ago. It is now loading new emails too, but no emails in the past month, read or unread. It's gmail, set up through the phone, I've restarted restored

    Strange email problem; it started only loading unread emails, but from 3 months ago. It is now loading new emails too, but no emails in the past month, read or unread. It's gmail, set up through the phone, I've restarted restored and updated firmware, deleted the account, anything I could think of, but it's just not accurately downloading the most recent emails.

    The answer is very simple: You were not the original owner of the phone. Target sold you a phone that had been returned. You can verify the date of the original sale here: Apple - Support - Check Your Service and Support Coverage. I suspect you will find that the warranty expiration date is not one year from the date that you bought it.

  • Problem with Safari **Safari can't connect to the server**

    My internet is working fine, but I keep having to refresh the page because I'm always getting "safari can't connect to the server".  Same thing happens with different browsers.  I've read a couple things online and unistalled everything that I think is causing the problem but it's still happening frequently.  Any help would be greatly appreciated!

    Most school networks are closed networks. You can access their Intranet, with all the files and peripherals and everything, but you need to have a specific password or IP address to access any outside connection. I have an ibook G4 that's 3 years old. I used it in high-school to access AOL wirelessly. That was before closed and protected networks were prefered. It shouldn't matter if the school intranet is widows based or not. You need to access your own internet service sometimes in order to get any reaction. If you simply use safari, you might only be connecting to the schools intranet, which only links together the schools computers and keeps the system isolated. Also, you need to check your firewall settings, in fact, just turn off the firewall. The schools sytem is firewalled up the bum and you shouldn't get attacks anyway because you're running the mac os.
    You might also try an alternative approach. Go into a computer lab, access one of the systems, then go to control panels and look up every connection you can find. Take down all of the info and then see which matches up with similar info on your mac. Then go to another pc and look up the same info again. Is it different? How? Then take that listing to the system administrator and show them. They may not know that a mac has a simpler interface than the pc, so you may have to do some prodding to get them to take a look. If they still tell you it wont work, you could try boot-camp or a virtualizer (to let you run windows alongside the mac os). If you use a virtualizer, you can get your own copy of windows and then share it's connection to the main system to the mac.

Maybe you are looking for

  • Text message notification missing

    My granddaughter has an iPhone (iPhone 4).  She is not receiving any notice of an incoming text message although she is receiving the messages fine.. There is no badge by the text message icon showing the number of unread messages or any other indica

  • ASA Clientless SSL VPN can't access login pages on websites

    When I'm doing a clientless SSL VPN to my ASA and using the ASA to browse websites, I can pretty much go on to just about any website except specificly login websites. I can go on google and yahoo but when I click the "mail" button it just gives me a

  • Stock Write-off Report

    Dear Friends, Is there a transaction or Report available to see the write-off stock by plant or through any movement types ? Please suggest the requirement is as fallows: Report needs to be selectable by IPC or ICC. Or plant The report will need to s

  • How to delete the many versions of the same song?

    Help please, how do I delete old versions of a song? When I add to or tweak a piece, I first save it with a new name, like song 1, then song 2, etc. so that I have a copy of every change. This takes up space when I have 50 versions each of 10 songs.

  • How to correct for dual color casts?

    It seems that I have a slight warm color cast from the top of my image down and a slight cool color cast from the bottom of my image up. The center area is color neutral. How to I correct for these color casts? I tried an adjustment layer with linear