5508 unable to form redundant pair

Hi,
We have two 5508 controllers which were actually working fine in ap sso mode when it was initially configured. Due to a recent network move, both 5508 were removed from current location & installed at another location.
When we re-installed & connected all the connections, the ap sso is not forming and it says Unknown-Communication down & goes into maintenance mode.
(Cisco Controller-1) >show redundancy summary
Redundancy Mode = SSO ENABLED
     Local State = ACTIVE
      Peer State = UNKNOWN - Communication Down
            Unit = Primary
         Unit ID = 6C:41:6A:5E:E7:00
Redundancy State = Non Redundant
    Mobility MAC = 6C:41:6A:5E:E7:00
Redundancy Management IP Address................. 10.20.15.17
Peer Redundancy Management IP Address............ 10.20.15.18
Redundancy Port IP Address....................... 169.254.15.17
Peer Redundancy Port IP Address.................. 169.254.15.18
Cisco Controller-2) >show redundancy summary
Redundancy Mode = SSO ENABLED
     Local State = MAINTENANCE
      Peer State = UNKNOWN - Communication Down
            Unit = Secondary - HA SKU
         Unit ID = 10:F3:11:9A:04:20
Redundancy State = Non Redundant
    Mobility MAC = 6C:41:6A:5E:E7:00
Maintenance Mode = Enabled
Maintenance cause= Negotiation Timeout
Redundancy Management IP Address................. 10.20.15.18
Peer Redundancy Management IP Address............ 10.20.15.17
Redundancy Port IP Address....................... 169.254.15.18
Peer Redundancy Port IP Address.................. 169.254.15.17
We tried disabling sso on secondary , followed by reboot but it didn't work
Some of the messages as seen during the process are :
WARNING: If peer unit's management and/or redundancy management entries are present as mobility
members please remove them before enabling redundancy.
Management Gateway and Peer Redundancy Management interface are not reachable.
Entering maintenance mode...
Please help with suggestions. Thanks
Message was edited by: sunny thomas

it doesn't appear that your management addresses are in the same subnet. on is .15 the other is .5, but the redundancy port is showing both should be .15
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Similar Messages

Unable installing Forms 11.1.2.0.0 on Win7

Hi,
I try to install Forms 11g R2 11.1.2.0.0 / WL 10.3.5. on Win7 32 and
get a error while configuring "Unable to create ASInstance":
1.) installed WL incl. patch p12564602_1035_Generic
2.) try to install Forms 11g R2 11.1.2.0.0:
configuring process:
- domain creating with success
- ASInstance creating breaks.
I cannot found any logs for clarification or other note,
please help.
Many thanks

Hi,
now I get a log after setting the ip address 127.0.0.1 in the loopback and etc\hosts and
it also stops in the ASInstance creating:
Creating Instance Service..
AdminServer port is 7001
trying to connect to wstwin7 7001
Successful
getDomainRuntimeMBeanServerConnection ...
Connecting to Domain runtime ...
trying to connect to wstwin7 7001
Successfully connected to the Domain Runtime ...
trying to connect to wstwin7 7001
Successful
MBean Server Connection is :javax.management.remote.rmi.RMIConnector$RemoteMBeanServerConnection@1b21b91
wstwin7 7001
weblogic.Deployer invoked with options: -adminurl wstwin7:7001 -username weblogic -name NonJ2EEManagement -source D:\orafrm11gr2\Oracle_FRHome1\opmn\applications\NonJ2EEManagement.ear -nostage -deploy -upload -noexit
+<28.11.2011 19:54 Uhr MEZ> <Info> <J2EE Deployment SPI> <BEA-260121> <Initiating deploy operation for application, NonJ2EEManagement [archive: D:\orafrm11gr2\Oracle_FRHome1\opmn\applications\NonJ2EEManagement.ear], to configured targets.>+
java.lang.Exception: oracle.as.provisioning.exception.ASProvisioningException
+     at oracle.as.install.classic.ca.standard.InstanceProvisioningTask.doExecute(InstanceProvisioningTask.java:222)+
+     at oracle.as.install.classic.ca.standard.StandaloneTool.execute(StandaloneTool.java:50)+
+     at oracle.as.install.classic.ca.standard.StandardProvisionTaskList.execute(StandardProvisionTaskList.java:61)+
+     at oracle.as.install.classic.ca.ClassicConfigMain.doExecute(ClassicConfigMain.java:124)+
+     at oracle.as.install.engine.modules.configuration.client.ConfigAction.execute(ConfigAction.java:339)+
+     at oracle.as.install.engine.modules.configuration.action.TaskPerformer.run(TaskPerformer.java:87)+
+     at oracle.as.install.engine.modules.configuration.action.TaskPerformer.startConfigAction(TaskPerformer.java:104)+
+     at oracle.as.install.engine.modules.configuration.action.ActionRequest.perform(ActionRequest.java:15)+
+     at oracle.as.install.engine.modules.configuration.action.RequestQueue.perform(RequestQueue.java:63)+
+     at oracle.as.install.engine.modules.configuration.standard.StandardConfigActionManager.start(StandardConfigActionManager.java:158)+
+     at oracle.as.install.engine.modules.configuration.boot.ConfigurationExtension.kickstart(ConfigurationExtension.java:81)+
+     at oracle.as.install.engine.modules.configuration.ConfigurationModule.run(ConfigurationModule.java:83)+
+     at java.lang.Thread.run(Thread.java:662)+
Caused by: oracle.as.provisioning.exception.ASProvisioningException
+     at oracle.as.provisioning.engine.Config.executeConfigWorkflow_WLS(Config.java:872)+
+     at oracle.as.install.classic.ca.standard.InstanceProvisioningTask.doExecute(InstanceProvisioningTask.java:218)+
+     ... 12 more+
Caused by: oracle.as.provisioning.engine.CfgWorkflowException
+     at oracle.as.provisioning.engine.Engine.processEventResponse(Engine.java:596)+
+     at oracle.as.provisioning.fmwadmin.ASInstanceProv.createInstance(ASInstanceProv.java:178)+
+     at oracle.as.provisioning.fmwadmin.ASInstanceProv.createInstanceAndComponents(ASInstanceProv.java:116)+
+     at oracle.as.provisioning.engine.WorkFlowExecutor._createASInstancesAndComponents(WorkFlowExecutor.java:523)+
+     at oracle.as.provisioning.engine.WorkFlowExecutor.executeWLSWorkFlow(WorkFlowExecutor.java:439)+
+     at oracle.as.provisioning.engine.Config.executeConfigWorkflow_WLS(Config.java:866)+
+     ... 13 more+
Caused by: oracle.as.provisioning.util.ConfigException:
Fehler beim Erstellen der AS-Instanz asinst_1.
Cause:
Ein interner Vorgang war nicht erfolgreich: Unable to validate NonJ2EEManagement Application deployment on admin server.
Action:
Weitere Informationen finden Sie in den Logs.
+     at oracle.as.provisioning.util.ConfigException.createConfigException(ConfigException.java:123)+
+     at oracle.as.provisioning.fmwadmin.ASInstanceProv._createInstance(ASInstanceProv.java:317)+
+     at oracle.as.provisioning.fmwadmin.ASInstanceProv.createInstance(ASInstanceProv.java:166)+
+     ... 17 more+
Caused by: oracle.as.config.ProvisionException: Unable to validate NonJ2EEManagement Application deployment on admin server.
+     at oracle.as.config.impl.RuntimeServiceConnection.validateNonj2eeApplication(RuntimeServiceConnection.java:703)+
+     at oracle.as.config.impl.RuntimeServiceConnection.deployIfNecessary(RuntimeServiceConnection.java:199)+
+     at oracle.as.config.impl.OracleASInstanceImpl.create(OracleASInstanceImpl.java:92)+
+     at oracle.as.provisioning.fmwadmin.ASInstanceProv._createInstance(ASInstanceProv.java:249)+
+     ... 18 more+
Caused by: oracle.as.config.utl.DeployerException: NonJ2EEManagement Applicationdeployment failed.
+     at oracle.as.config.utl.Deployer.deployApplication(Deployer.java:97)+
+     at oracle.as.config.utl.Deployer.deploy(Deployer.java:52)+
+     at oracle.as.config.impl.RuntimeServiceConnection.deployNonj2eeApplication(RuntimeServiceConnection.java:226)+
+     at oracle.as.config.impl.RuntimeServiceConnection.validateNonj2eeApplication(RuntimeServiceConnection.java:695)+
+     ... 21 more+
Caused by: java.lang.reflect.InvocationTargetException
+     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)+
+     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)+
+     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)+
+     at java.lang.reflect.Method.invoke(Method.java:597)+
+     at oracle.as.config.utl.Deployer.deployApplication(Deployer.java:95)+
+     ... 24 more+
+Caused by: weblogic.management.ManagementException: [Deployer:149003]Unable to access application source information in '<!DOCTYPE HTML PUBLIC "-\W3C\DTD HTML 4.0 Draft\EN">\app\NonJ2EEManagement.ear' for application 'NonJ2EEManagement'. The specific error is: No application files exist.+
+     at weblogic.deploy.internal.adminserver.operations.OperationHelper.validateSource(OperationHelper.java:354)+
+     at weblogic.deploy.internal.adminserver.operations.OperationHelper.getArchiveVersionIdFromSource(OperationHelper.java:164)+
+     at weblogic.deploy.internal.adminserver.operations.OperationHelper.getAndValidateVersionIdWithSrc(OperationHelper.java:202)+
+     at weblogic.deploy.internal.adminserver.operations.ActivateOperation.updateConfiguration(ActivateOperation.java:48)+
+     at weblogic.deploy.internal.adminserver.operations.DeployOperation.updateConfiguration(DeployOperation.java:35)+
+     at weblogic.deploy.internal.adminserver.operations.AbstractOperation.updateConfigurationAndInitializeDeployment(AbstractOperation.java:386)+
+     at weblogic.deploy.internal.adminserver.operations.AbstractOperation.execute(AbstractOperation.java:227)+
+     at weblogic.management.deploy.internal.DeployerRuntimeImpl$2.run(DeployerRuntimeImpl.java:837)+
+     at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)+
+     at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)+
+     at weblogic.management.deploy.internal.DeployerRuntimeImpl.performDeployerActions(DeployerRuntimeImpl.java:846)+
+     at weblogic.management.deploy.internal.DeployerRuntimeImpl.deploy(DeployerRuntimeImpl.java:410)+
+     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)+
+     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)+
+     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)+
+     at java.lang.reflect.Method.invoke(Method.java:597)+
+     at weblogic.management.jmx.modelmbean.WLSModelMBean.invoke(WLSModelMBean.java:437)+
+     at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.invoke(DefaultMBeanServerInterceptor.java:836)+
+     at com.sun.jmx.mbeanserver.JmxMBeanServer.invoke(JmxMBeanServer.java:761)+
+     at weblogic.management.mbeanservers.domainruntime.internal.FederatedMBeanServerInterceptor.invoke(FederatedMBeanServerInterceptor.java:349)+
+     at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)+
+     at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)+
+     at weblogic.management.mbeanservers.internal.JMXContextInterceptor.invoke(JMXContextInterceptor.java:263)+
+     at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)+
+     at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)+
+     at weblogic.management.mbeanservers.internal.SecurityMBeanMgmtOpsInterceptor.invoke(SecurityMBeanMgmtOpsInterceptor.java:65)+
+     at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)+
+     at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)+
+     at weblogic.management.mbeanservers.internal.SecurityInterceptor.invoke(SecurityInterceptor.java:444)+
+     at weblogic.management.jmx.mbeanserver.WLSMBeanServer.invoke(WLSMBeanServer.java:323)+
+     at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder$11$1.run(JMXConnectorSubjectForwarder.java:663)+
+     at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder$11.run(JMXConnectorSubjectForwarder.java:661)+
+     at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)+
+     at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder.invoke(JMXConnectorSubjectForwarder.java:654)+
+     at javax.management.remote.rmi.RMIConnectionImpl.doOperation(RMIConnectionImpl.java:1427)+
+     at javax.management.remote.rmi.RMIConnectionImpl.access$200(RMIConnectionImpl.java:72)+
+     at javax.management.remote.rmi.RMIConnectionImpl$PrivilegedOperation.run(RMIConnectionImpl.java:1265)+
+     at javax.management.remote.rmi.RMIConnectionImpl.doPrivilegedOperation(RMIConnectionImpl.java:1367)+
+     at javax.management.remote.rmi.RMIConnectionImpl.invoke(RMIConnectionImpl.java:788)+
+     at javax.management.remote.rmi.RMIConnectionImpl_WLSkel.invoke(Unknown Source)+
+     at weblogic.rmi.internal.BasicServerRef.invoke(BasicServerRef.java:668)+
+     at weblogic.rmi.internal.BasicServerRef$1.run(BasicServerRef.java:523)+
+     at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)+
+     at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:146)+
+     at weblogic.rmi.internal.BasicServerRef.handleRequest(BasicServerRef.java:518)+
+     at weblogic.rmi.internal.wls.WLSExecuteRequest.run(WLSExecuteRequest.java:119)+
+     at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)+
+     at weblogic.work.ExecuteThread.run(ExecuteThread.java:178)+
Executing Task: Starting OPMN
GJS: About to call startOpmn
GJS: Entered startOpmn
Has anyone an idea for solving this problem?
Many thanks

Unable Submit Form Value to Action when running struts-portlet in OracleAS

Hi,I have develop a portlet using struts & pdk, after that deploy it by OC4J and register the
provider at Oracle Application Server 10g 10.1.2.2.
However the formbean value is unable passing to action after clicking submit button,this problem
doesn't comeout when i run my code as stand alone application.
here is my application code:
1. Action Class:
public class ZoneAction
extends DispatchAction
public ActionForward display(ActionMapping mapping, ActionForm form,
                               HttpServletRequest request,
                               HttpServletResponse response)
    throws IOException, ServletException
    ZoneHibernate zh = new ZoneHibernate();
    List list = zh.retrieveAllZone();
    ZoneForms zf = new ZoneForms();
    ZoneForm blankForm = new ZoneForm();
    list.add(blankForm);
    zf.setZoneForms(list);
    request.setAttribute("zoneForms", zf);
    return mapping.findForward("success");
2.Provider.xml:
<provider class="oracle.portal.provider.v2.DefaultProviderDefinition">
   <session>true</session>
   <passAllUrlParams>true</passAllUrlParams>
   <portlet class="oracle.portal.provider.v2.DefaultPortletDefinition">
      <id>1</id>
      <name>irmsPortlet</name>
      <title>iRMS Portlet</title>
      <description></description>
      <timeout>40</timeout>
      <showEditToPublic>false</showEditToPublic>
      <hasAbout>false</hasAbout>
      <showEdit>false</showEdit>
      <hasHelp>false</hasHelp>
      <showEditDefault>false</showEditDefault>
      <showDetails>false</showDetails>
      <renderer class="oracle.portal.provider.v2.render.RenderManager">
         <renderContainer>true</renderContainer>
         <renderCustomize>true</renderCustomize>
         <autoRedirect>true</autoRedirect>
         <contentType>text/html</contentType>
         <showPage class="oracle.portal.provider.v2.render.http.StrutsRenderer">
         <defaultAction>/jsp/zone_maintenance.jsp</defaultAction>
         </showPage>
      </renderer>
   </portlet>
</provider>
3. Action Mapping in struts-cofig.xml:
<action-mappings>
    <action path="/ZoneMaintenance"
            type="my.com.irms.action.ZoneAction"
            name="zoneForms"
            scope="request"
            parameter="action"
            input="/jsp/zone_maintenance.jsp">
      <forward name="success" path="/jsp/zone_maintenance.jsp"/>
    </action>
</action-mappings>
4.jsp:
<pdk-html:form action="/ZoneMaintenance.do">
-div id="action"-<pdk-html:hidden name="zoneForms" property="action"/>-/div-
<logic:notEmpty name="zoneForms" property="zoneForms">
<table border="1">
<thead>
            <tr>
                <th><bean:message key="zone.zone"/></th>
                <th><bean:message key="zone.disc"/></th>
           </tr>
</thead>
<tbody>
<logic:iterate id="zone" name="zoneForms" property="zoneForms" indexId="i">
            <tr id="tr${i}">
                <td>
                  <pdk-html:hidden name="zoneForms"
                                  property="zoneForms[${i}].rowStatus" value=""/>
                  <pdk-html:hidden name="zoneForms" property="zoneForms[${i}].id"/>
                  <input type="checkbox" onclick="update()">
                </td>
                <td><pdk-html:text name="zoneForms"
                                       property="zoneForms[${i}].zone" size="10"
                                       onchange="rowDataChanged('tb1',${i})"/></td>
                <td><pdk-html:text name="zoneForms"
                                       property="zoneForms[${i}].disc" size="30"
                                       onchange="rowDataChanged('tb1',${i})"/></td>
            </tr>
</logic:iterate>
</tbody>
</table>
<input type="button" value="Submit" onclick="submitForm('save')"/>
</logic:notEmpty>
<input type="button" value="Display" onclick="submitForm('display')"/>
</pdk-html:form>
5.javascript for submitForm():
function submitForm(param)
        document.getElementById("action")
       .getElementsByTagName("input")[0].value = param;
        document.forms[0].submit();
6.web.xml
<?xml version = '1.0' encoding = 'windows-1252'?>
<web-app>
<description>Empty web.xml file for Web Application</description>
<servlet>
    <servlet-name>action</servlet-name>
    <servlet-class>
          org.apache.struts.action.ActionServlet
    </servlet-class>
    <init-param>
      <param-name>config</param-name>
      <param-value>
           /WEB-INF/struts-config.xml
      </param-value>
    </init-param>
    <load-on-startup>1</load-on-startup>
</servlet>
<servlet>
    <description>Extended Portal
                 SOAP Server</description>
    <servlet-name>SOAPServlet</servlet-name>
    <servlet-class>
           oracle.webdb.provider.v2.adapter.SOAPServlet
    </servlet-class>
    <init-param>
      <param-name>resourceServletMapping</param-name>
      <param-value>/pdkresource</param-value>
    </init-param>
</servlet>
<servlet>
    <description>Image resource server</description>
    <servlet-name>ResourceServlet</servlet-name>
    <servlet-class>
         oracle.webdb.provider.v2.adapter.ResourceServlet
    </servlet-class>
</servlet>
<servlet-mapping>
    <servlet-name>action</servlet-name>
    <url-pattern>*.do</url-pattern>
</servlet-mapping>
<servlet-mapping>
    <servlet-name>SOAPServlet</servlet-name>
    <url-pattern>/providers</url-pattern>
</servlet-mapping>
<servlet-mapping>
    <servlet-name>SOAPServlet</servlet-name>
    <url-pattern>/providers/*</url-pattern>
</servlet-mapping>
<servlet-mapping>
    <servlet-name>ResourceServlet</servlet-name>
    <url-pattern>/pdkresource/*</url-pattern>
</servlet-mapping>
<session-config>
    <session-timeout>35</session-timeout>
</session-config>
<mime-mapping>
    <extension>html</extension>
    <mime-type>text/html</mime-type>
</mime-mapping>
<mime-mapping>
    <extension>txt</extension>
    <mime-type>text/plain</mime-type>
</mime-mapping>
</web-app>
Can anyone help me? thanks.

It is probably easier to do with with a standard tag than the <html:button> tag, as it means you can nest the
<input type="button" name="more" value="more" onclick="setID(<bean:write name="bloodbankList" property="id"/>)"/>or maybe like this:
<bean:define id="bbId" name="bloodbankList" property="id"/>
<html:button property="More" value="More" style="color: #00007D; text-transform: uppercase; letter-spacing: 2pt; background-color: #6B719C; border: 2 solid #00007D"   onclick="<%= "setID(" + id + ");" %>" />Cheers,
evnafets

Unable to form af:table in navigation Menu Model

Hi,
Am using jdeveloper 11.1.2.1.0,
I have developed my project with reference to the link below
http://www.youtube.com/watch?v=cInX_FMZJaQ
Am unable to drag and drop a VO as af:table in my jspx pages.
Could any one pls explain me where i went wrong?

It is not possible to drop VO directly from the model into pages. On JDeveloper, go to the Data controls view of the Applications Navigator tab, click on the refresh icon, select your application module and then then the VO instance you want to drag and drop. I'm just guessing what you could be doing wrong. Describe what steps you did. Also make sure, if you use a template, that you have declared facets and referenced the facet where you want to create the table in a container that allows tables.
Edited by: Paulo Moniz on Oct 27, 2012 8:03 PM

Unable to form a single cluster island. Two clusters formed and kills one

I am trying to use ReplicatedCache and deployed the web application on four Webspher appserver JVMs in two linux servers (2 boxes). Server1 (A&B) Server2 (A&B). Server1A and Server2A physical clusters and likewise Server1B and Server2B are physical clusters.
Server1 A & B forms a coherence cluster island and Server2 A & B forms another cluster island. After few seconds the Server2 cluster node on B identifies the existence of another cluster island and activates the panic protocol. So the Server1 A or B receives the panic message and sends kill message to the other cluster member on Server1. Ultimately, the cluster service on Server1 is stopped and both the members leave the cluster. How do I fix this?
I want to have one cluster and all the four nodes to be members of this cluster so that the cache is replicated in all the four nodes. Please help.
Note: The coherence.jar and tangosol.jar are inside the WEB-INF/lilb in the war and the same war file deployed in four jvms.
Included below the logs from four jvms:
Log - Server2-B:
[9/9/08 18:58:15:754 GMT] 0000003a SystemErr R 2008-09-09 18:58:15.731 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=server.startup : 0, member=n/a): Loaded operational overrides from resource "wsjar:file:/opt/IBM/WebSphere61/AppServer/profiles/ADNA-S-Node/installedApps/ADNA-S/ADNALinker-B.ear/ADNALinker.war/WEB-INF/lib/coherence.jar!/tangosol-coherence-override-prod.xml"
[9/9/08 18:58:15:755 GMT] 0000003a SystemErr R 2008-09-09 18:58:15.733 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=server.startup : 0, member=n/a): Optional configuration override "/tangosol-coherence-override.xml" is not specified
[9/9/08 18:58:15:909 GMT] 0000003a SystemErr R 2008-09-09 18:58:15.899 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=server.startup : 0, member=n/a): Loaded cache configuration from resource "file:/opt/IBM/WebSphere61/AppServer/profiles/ADNA-S-Node/installedApps/ADNA-S/ADNALinker-B.ear/ADNALinker.war/WEB-INF/classes/adnalinker-coherence-config.xml"
[9/9/08 18:58:17:516 GMT] 0000003a SystemErr R 2008-09-09 18:58:17.516 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a
[9/9/08 18:58:49:242 GMT] 0000003a SystemErr R 2008-09-09 18:58:49.241 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=Cluster, member=n/a): Created a new cluster with Member(Id=1, Timestamp=2008-09-09 18:58:17.319, Address=10.29.29.33:8088, MachineId=2593, Edition=DataGrid Edition, Mode=Production, CpuCount=4, SocketCount=2) UID=0x0A1D1D210000011C487A76670A211F98
[9/9/08 18:58:49:501 GMT] 0000003a SystemErr R 2008-09-09 18:58:49.500 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=ReplicatedCache, member=1): Service ReplicatedCache joined the cluster with senior service member 1
[9/9/08 18:58:49:589 GMT] 0000003a SystemErr R 2008-09-09 18:58:49.588 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=1): Member(Id=2, Timestamp=2008-09-09 18:58:49.379, Address=10.29.29.33:8089, MachineId=2593) joined Cluster with senior member 1
[9/9/08 18:58:49:966 GMT] 0000003a SystemErr R 2008-09-09 18:58:49.965 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=1): Member 2 joined Service ReplicatedCache with senior member 1
[9/9/08 18:58:50:130 GMT] 00000032 SystemErr R log4j:WARN No appenders could be found for logger (org.apache.struts.util.PropertyMessageResources).
[9/9/08 18:58:50:130 GMT] 00000032 SystemErr R log4j:WARN Please initialize the log4j system properly.
[9/9/08 18:58:51:285 GMT] 0000003a SystemErr R 2008-09-09 18:58:51.262 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=1): TcpRing: connecting to member 2 using TcpSocket{State=STATE_OPEN, Socket=Socket[addr=houmaasas02.cce.star/10.29.29.33,port=8089,localport=44068]}
[9/9/08 18:58:51:750 GMT] 00000034 SystemErr R log4j:WARN No appenders could be found for logger (org.apache.struts.util.PropertyMessageResources).
[9/9/08 18:58:51:751 GMT] 00000034 SystemErr R log4j:WARN Please initialize the log4j system properly.
[9/9/08 20:23:28:160 GMT] 0000003a SystemErr R 2008-09-09 20:23:28.160 Tangosol Coherence DGE 3.2.2/371 <Warning> (thread=Cluster, member=1): **An existence of a cluster island with senior Member(Id=1, Timestamp=2008-09-09 18:58:17.537, Address=10.29.29.31:8088, MachineId=2591) containing 2 nodes have been detected. Since this Member(Id=1, Timestamp=2008-09-09 18:58:17.319, Address=10.29.29.33:8088, MachineId=2593) is the senior of an older cluster island, the panic protocol is being activated to stop the other island's senior and all junior nodes that belong to it.**
**[9/9/08 20:23:28:161 GMT] 0000003a SystemErr R 2008-09-09 20:23:28.161 Tangosol Coherence DGE 3.2.2/371 <Warning> (thread=Cluster, member=1): Received panic from junior member Member(Id=2, Timestamp=2008-09-09 18:58:49.379, Address=10.29.29.33:8089, MachineId=2593) caused by Member(Id=1, Timestamp=2008-09-09 18:58:17.537, Address=10.29.29.31:8088, MachineId=2591)*******************************************************
Log Server2-A:
[9/9/08 18:58:16:875 GMT] 0000003d SystemErr R 2008-09-09 18:58:16.787 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=server.startup : 1, member=n/a): Loaded operational overrides from resource "wsjar:file:/opt/IBM/WebSphere61/AppServer/profiles/ADNA-S-Node/installedApps/ADNA-S/ADNALinker-A.ear/ADNALinker.war/WEB-INF/lib/coherence.jar!/tangosol-coherence-override-prod.xml"
[9/9/08 18:58:16:876 GMT] 0000003d SystemErr R 2008-09-09 18:58:16.790 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=server.startup : 1, member=n/a): Optional configuration override "/tangosol-coherence-override.xml" is not specified
[9/9/08 18:58:17:124 GMT] 0000003d SystemErr R 2008-09-09 18:58:17.045 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=server.startup : 1, member=n/a): Loaded cache configuration from resource "file:/opt/IBM/WebSphere61/AppServer/profiles/ADNA-S-Node/installedApps/ADNA-S/ADNALinker-A.ear/ADNALinker.war/WEB-INF/classes/adnalinker-coherence-config.xml"
[9/9/08 18:58:18:479 GMT] 0000003d SystemErr R 2008-09-09 18:58:18.479 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a
[9/9/08 18:58:49:607 GMT] 0000003d SystemErr R 2008-09-09 18:58:49.601 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=Cluster, member=n/a): This Member(Id=2, Timestamp=2008-09-09 18:58:49.379, Address=10.29.29.33:8089, MachineId=2593, Edition=DataGrid Edition, Mode=Production, CpuCount=4, SocketCount=2) joined cluster with senior Member(Id=1, Timestamp=2008-09-09 18:58:17.319, Address=10.29.29.33:8088, MachineId=2593, Edition=DataGrid Edition, Mode=Production, CpuCount=4, SocketCount=2)
[9/9/08 18:58:49:658 GMT] 0000003d SystemErr R 2008-09-09 18:58:49.658 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=n/a): Member 1 joined Service ReplicatedCache with senior member 1
[9/9/08 18:58:49:993 GMT] 0000003d SystemErr R 2008-09-09 18:58:49.992 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=ReplicatedCache, member=2): Service ReplicatedCache joined the cluster with senior service member 1
[9/9/08 18:58:50:515 GMT] 00000035 SystemErr R log4j:WARN No appenders could be found for logger (org.apache.struts.util.PropertyMessageResources).
[9/9/08 18:58:50:516 GMT] 00000035 SystemErr R log4j:WARN Please initialize the log4j system properly.
[9/9/08 18:58:51:310 GMT] 0000003d SystemErr R 2008-09-09 18:58:51.287 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=TcpRingListener, member=2): TcpRing: connecting to member 1 using TcpSocket{State=STATE_OPEN, Socket=Socket[addr=/10.29.29.33,port=44068,localport=8089]}
[9/9/08 18:58:52:383 GMT] 00000036 SystemErr R log4j:WARN No appenders could be found for logger (org.apache.struts.util.PropertyMessageResources).
[9/9/08 18:58:52:383 GMT] 00000036 SystemErr R log4j:WARN Please initialize the log4j system properly.
[9/9/08 20:23:28:162 GMT] 0000003d SystemErr R 2008-09-09 20:23:28.162 Tangosol Coherence DGE 3.2.2/371 <Error> (thread=Cluster, member=2): Received panic from senior member Member(Id=1, Timestamp=2008-09-09 18:58:17.319, Address=10.29.29.33:8088, MachineId=2593) caused by Member(Id=1, Timestamp=2008-09-09 18:58:17.537, Address=10.29.29.31:8088, MachineId=2591)
Log from Server1-A:
[9/9/08 18:58:15:656 GMT] 0000002a SystemErr R 2008-09-09 18:58:15.645 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=server.startup : 2, member=n/a): Loaded operational overrides from resource "wsjar:file:/opt/IBM/WebSphere61/AppServer/profiles/ADNA-S-Node/installedApps/ADNA-S/ADNALinker-A.ear/ADNALinker.war/WEB-INF/lib/coherence.jar!/tangosol-coherence-override-prod.xml"
[9/9/08 18:58:15:656 GMT] 0000002a SystemErr R 2008-09-09 18:58:15.647 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=server.startup : 2, member=n/a): Optional configuration override "/tangosol-coherence-override.xml" is not specified
[9/9/08 18:58:15:800 GMT] 0000002a SystemErr R 2008-09-09 18:58:15.790 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=server.startup : 2, member=n/a): Loaded cache configuration from resource "file:/opt/IBM/WebSphere61/AppServer/profiles/ADNA-S-Node/installedApps/ADNA-S/ADNALinker-A.ear/ADNALinker.war/WEB-INF/classes/adnalinker-coherence-config.xml"
[9/9/08 18:58:17:827 GMT] 0000002a SystemErr R 2008-09-09 18:58:17.796 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a
[9/9/08 18:58:49:711 GMT] 0000002a SystemErr R 2008-09-09 18:58:49.711 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=Cluster, member=n/a): Created a new cluster with Member(Id=1, Timestamp=2008-09-09 18:58:17.537, Address=10.29.29.31:8088, MachineId=2591, Edition=DataGrid Edition, Mode=Production, CpuCount=4, SocketCount=2) UID=0x0A1D1D1F0000011C487A77410A1F1F98
[9/9/08 18:58:49:949 GMT] 0000002a SystemErr R 2008-09-09 18:58:49.946 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=1): Member(Id=2, Timestamp=2008-09-09 18:58:49.739, Address=10.29.29.31:8089, MachineId=2591) joined Cluster with senior member 1
[9/9/08 18:58:50:124 GMT] 0000002a SystemErr R 2008-09-09 18:58:50.122 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=ReplicatedCache, member=1): Service ReplicatedCache joined the cluster with senior service member 1
[9/9/08 18:58:50:355 GMT] 0000002a SystemErr R 2008-09-09 18:58:50.354 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=1): Member 2 joined Service ReplicatedCache with senior member 1
[9/9/08 18:58:50:654 GMT] 00000025 SystemErr R log4j:WARN No appenders could be found for logger (org.apache.struts.util.PropertyMessageResources).
[9/9/08 18:58:50:654 GMT] 00000025 SystemErr R log4j:WARN Please initialize the log4j system properly.
[9/9/08 18:58:51:745 GMT] 0000002a SystemErr R 2008-09-09 18:58:51.744 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=1): TcpRing: connecting to member 2 using TcpSocket{State=STATE_OPEN, Socket=Socket[addr=houmaasas01.cce.star/10.29.29.31,port=8089,localport=48201]}
[9/9/08 18:58:52:852 GMT] 00000024 SystemErr R log4j:WARN No appenders could be found for logger (org.apache.struts.util.PropertyMessageResources).
[9/9/08 18:58:52:852 GMT] 00000024 SystemErr R log4j:WARN Please initialize the log4j system properly.
[9/9/08 19:08:22:944 GMT] 0000002a SystemErr R 2008-09-09 19:08:22.944 Tangosol Coherence DGE 3.2.2/371 <Warning> (thread=Cluster, member=1): Received panic from junior member Member(Id=2, Timestamp=2008-09-09 18:58:49.739, Address=10.29.29.31:8089, MachineId=2591) caused by Member(Id=1, Timestamp=2008-09-09 18:58:17.319, Address=10.29.29.33:8088, MachineId=2593)
[9/9/08 20:23:28:161 GMT] 0000002a SystemErr R 2008-09-09 20:23:28.160 Tangosol Coherence DGE 3.2.2/371 <Error> (thread=Cluster, member=1): Received a Kill message from a valid Member(Id=2, Timestamp=2008-09-09 18:58:49.379, Address=10.29.29.33:8089, MachineId=2593); stopping cluster service.
[9/9/08 20:23:30:168 GMT] 0000002a SystemErr R 2008-09-09 20:23:30.166 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=1): Service Cluster left the cluster
[9/9/08 20:23:30:171 GMT] 0000002a SystemErr R 2008-09-09 20:23:30.170 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=ReplicatedCache, member=1): Service ReplicatedCache left the cluster
Log from Server1-B:
[9/9/08 18:58:18:602 GMT] 00000043 SystemErr R 2008-09-09 18:58:18.591 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=server.startup : 0, member=n/a): Loaded operational overrides from resource "wsjar:file:/opt/IBM/WebSphere61/AppServer/profiles/ADNA-S-Node/installedApps/ADNA-S/ADNALinker-B.ear/ADNALinker.war/WEB-INF/lib/coherence.jar!/tangosol-coherence-override-prod.xml"
[9/9/08 18:58:18:602 GMT] 00000043 SystemErr R 2008-09-09 18:58:18.593 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=server.startup : 0, member=n/a): Optional configuration override "/tangosol-coherence-override.xml" is not specified
[9/9/08 18:58:18:784 GMT] 00000043 SystemErr R 2008-09-09 18:58:18.784 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=server.startup : 0, member=n/a): Loaded cache configuration from resource "file:/opt/IBM/WebSphere61/AppServer/profiles/ADNA-S-Node/installedApps/ADNA-S/ADNALinker-B.ear/ADNALinker.war/WEB-INF/classes/adnalinker-coherence-config.xml"
[9/9/08 18:58:20:282 GMT] 00000043 SystemErr R 2008-09-09 18:58:20.282 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a
[9/9/08 18:58:50:006 GMT] 00000043 SystemErr R 2008-09-09 18:58:50.006 Tangosol Coherence DGE 3.2.2/371 <Info> (thread=Cluster, member=n/a): This Member(Id=2, Timestamp=2008-09-09 18:58:49.739, Address=10.29.29.31:8089, MachineId=2591, Edition=DataGrid Edition, Mode=Production, CpuCount=4, SocketCount=2) joined cluster with senior Member(Id=1, Timestamp=2008-09-09 18:58:17.537, Address=10.29.29.31:8088, MachineId=2591, Edition=DataGrid Edition, Mode=Production, CpuCount=4, SocketCount=2)
[9/9/08 18:58:50:114 GMT] 00000043 SystemErr R 2008-09-09 18:58:50.114 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=2): Member 1 joined Service ReplicatedCache with senior member 1
[9/9/08 18:58:50:365 GMT] 00000043 SystemErr R 2008-09-09 18:58:50.361 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=ReplicatedCache, member=2): Service ReplicatedCache joined the cluster with senior service member 1
[9/9/08 18:58:50:894 GMT] 00000038 SystemErr R log4j:WARN No appenders could be found for logger (org.apache.struts.util.PropertyMessageResources).
[9/9/08 18:58:50:895 GMT] 00000038 SystemErr R log4j:WARN Please initialize the log4j system properly.
[9/9/08 18:58:51:808 GMT] 00000043 SystemErr R 2008-09-09 18:58:51.806 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=TcpRingListener, member=2): TcpRing: connecting to member 1 using TcpSocket{State=STATE_OPEN, Socket=Socket[addr=/10.29.29.31,port=48201,localport=8089]}
[9/9/08 20:23:28:239 GMT] 00000043 SystemErr R 2008-09-09 20:23:28.237 Tangosol Coherence DGE 3.2.2/371 <Error> (thread=Cluster, member=2): Received a Kill message from a valid Member(Id=1, Timestamp=2008-09-09 18:58:17.537, Address=10.29.29.31:8088, MachineId=2591); stopping cluster service.
[9/9/08 20:23:28:240 GMT] 00000043 SystemErr R 2008-09-09 20:23:28.238 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=Cluster, member=2): Service Cluster left the cluster
[9/9/08 20:23:28:242 GMT] 00000043 SystemErr R 2008-09-09 20:23:28.241 Tangosol Coherence DGE 3.2.2/371 <D5> (thread=ReplicatedCache, member=2): Service ReplicatedCache left the cluster
Edited by: user533771 on Sep 10, 2008 9:56 AM

Hi,
Please take a look at this wiki page on how to verify and troubleshoot multicast support: http://wiki.tangosol.com/display/COH33UG/Multicast+Test . Most likely (but I can be wrong), all you need to do is to add java.net.preferIPv4Stack=true system property to the jvm command line.
Regards,
Dimitri

Unable deploy form on web from forms10g developer suit..????

hi all
i download the 10g developer suit .i am not able deploy the form on browser ?
actually i tried all possiblities to deploy
1 start listner
2 change the port
the connection test is successful but it is not deployee on the web what should be the reason
second question is
how to get the status of listner it is started or not...........?
pls help me
regards
onkar

Seems like you have things mixed up.
The listener is for the database and not development suite.
For starters tell us what's going on when you try to run a form, after installation did you run the test from successfully?? try it.
You have to start OC4J to run a form from the forms builder.
try it and let me know what happens.
Regards,
Tony

Unable to issue "redundancy-protocol" command on CSS

This is really weird. I've done box-2-box redundancy on CSSs half a dozen times. I have a CSS 11050 on 5.0(33) code that does not recognize "redundancy-protocol" as a valid command on the VRRP interface.
Config of the CSS is really basic:
!Generated on 01/01/1980 00:00:11
!Active version: ap0500033
configure
!*************************** GLOBAL ***************************
bridge spanning-tree disabled
persistence reset remap
acl enable
ip redundancy
app
app session 192.168.1.2
ip route 0.0.0.0 0.0.0.0 14.60.64.1 1
!************************* INTERFACE *************************
interface e1
phy 100Mbits-FD
interface e2
bridge vlan 2
phy 100Mbits-FD
interface e3
phy 100Mbits-FD
interface e4
phy 100Mbits-FD
interface e5
phy 100Mbits-FD
interface e6
phy 100Mbits-FD
interface e8
phy 100Mbits-FD
bridge vlan 10
!************************** CIRCUIT **************************
circuit VLAN1
redundancy
ip address 14.218.74.110 255.255.254.0
circuit VLAN2
redundancy
ip address 14.60.64.211 255.255.248.0
circuit VLAN10
ip address 192.168.1.1 255.255.255.0
!************************** SERVICE **************************
service tempest
ip address 14.218.74.127
keepalive type http
keepalive uri "/checkServerStatus.html"
active
service tempest-ping
ip address 14.218.74.127
active
service zephyr
ip address 14.218.74.128
keepalive type http
keepalive uri "/checkServerStatus.html"
active
service zephyr-ping
ip address 14.218.74.128
active
!*************************** OWNER ***************************
owner HPS
content layer3
vip address 14.60.64.210
no persistent
add service tempest
primarySorryServer zephyr
active
!*************************** GROUP ***************************
group SOURCE-IP-NAT
vip address 14.218.74.112
active
!**************************** ACL ****************************
acl 10
clause 10 permit any any destination any
apply circuit-(VLAN10)
acl 20
clause 10 permit any any destination any
apply circuit-(VLAN1)
acl 30
clause 10 permit any any destination content HPS/layer3 sourcegroup SOURCE-IP-
NAT
clause 90 permit any any destination any
apply circuit-(VLAN2)
~~~~~~~~~~~~~~~~~~~~~~
Pretty simple, but when I go to configure VLAN10 as the interface to run VRRP on:
scc-lb1(config)# circuit VLAN10
scc-lb1(config-circuit[VLAN10])# redundancy-protocol
^
%% Invalid input detected at '^' marker.
scc-lb1(config-circuit[VLAN10])# re?
redundancy Configure this circuit for redundancy
restore Restore commands
*** Aliases ***
reboot_diags @configure;boot;rebo diags
reboot @configure;boot;rebo
scc-lb1(config-circuit[VLAN10])#
The "redundancy" command is the only command it will recognize.
Anybody have any clue what is happening here?
Thanks!

Hi,
In order to add "redundancy-protocol" to the circuit, you need to go into the ip address section after going into the circuit section and then it will be an available option.
Like this:
scc-lb1(config)# circuit VLAN10
once in the circuit section, type in the ip address of the circuit.
Then you will be in the ip address part of the config and type in "redundancy-protocol"
Regards
Pete Knoops
Cisco Systems

How to install Solaris8 when my computer unable boot form CDROM

The case same as above Subject, from blank harddisk.
Thanks everyone!!

Try booting from "Device Configuration Assistant" floppy disk. You may just download it from http://soldc.sun.com/support/drivers/dca_diskettes/
Jose Correa

IPS Redundancy Pair and Etherchannel

Guys,
Do yo have any experience with IPS redundandy ?
i have idea about it ?
|-----------|
|-----------| ---link-1--- IPS-1
|-switch-|
|-----------| ---link-2--- IPS-2
|-----------|
Two IPS (IPS-1 and IPS-2) is deployed in "out of bound" to one switch (I know it can be deployed use two switch and use inline topology but i don't have other switch :D). Link-1 and link-2 is etherchannel trunk. Etherchannel trunk carry vlan inside and vlan outside. In IPS-1 and IPS-2 there are mapping vlan for that vlan (inside <--> outside).
What do you think guys ?

Hi,
how did you solve this? Have you tried load-balancing using multichassis etherchannel?
Radim

Redundancy not forming with wlc

Hi,
We have two wlc 5508 running vers 7.4.100.60. They are not forming redundancy pair & are in maintenance mode.
Both RP's are connected physically direct.
Few outputs are given here:-
(WLC01) >show redundancy summary
Redundancy Mode = SSO ENABLED
     Local State = MAINTENANCE
      Peer State = UNKNOWN - Communication Down
            Unit = Primary
         Unit ID = 2C:11:5A:5F:C7:00
Redundancy State = Non Redundant
    Mobility MAC = 2C:11:5A:5F:C7:00
Maintenance Mode = Enabled
Maintenance cause= Negotiation Timeout
Redundancy Management IP Address................. 10.32.25.11
Peer Redundancy Management IP Address............ 10.32.25.12
Redundancy Port IP Address....................... 169.254.25.11
Peer Redundancy Port IP Address.................. 169.254.25.12
(WLC02) >show redundancy summary
Redundancy Mode = SSO ENABLED
     Local State = MAINTENANCE
      Peer State = UNKNOWN - Communication Down
            Unit = Secondary - HA SKU
         Unit ID = 10:B3:21:3C:01:B0
Redundancy State = Non Redundant
    Mobility MAC = 10:B3:21:3C:01:B0
Maintenance Mode = Enabled
Maintenance cause= Incompatible Software license
Redundancy Management IP Address................. 10.32.25.12
Peer Redundancy Management IP Address............ 10.32.25.11
Redundancy Port IP Address....................... 169.254.25.12
Peer Redundancy Port IP Address.................. 169.254.25.11
(WLC01) >show license summary
License Store: Primary License Storage
StoreIndex: 0 Feature: base                              Version: 1.0
        License Type: Permanent
        License State: Active, Not in Use
        License Count: Non-Counted
        License Priority: Medium
License Store: Evaluation License Storage
StoreIndex: 0 Feature: base-ap-count                     Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
        License Count: 500 / 0 (Active/In-use)
        License Priority: None
(WLC02) >show license summary
License Store: Primary License Storage
StoreIndex: 0 Feature: base                              Version: 1.0
        License Type: Permanent
        License State: Active, Not in Use
        License Count: Non-Counted
        License Priority: Medium
License Store: Evaluation License Storage
StoreIndex: 0 Feature: base-ap-count                     Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
        License Count: 500 / 0 (Active/In-use)
        License Priority: None
In addition, other errors are also seen during the process.
Starting Redundancy: Starting Peer Search Timer of 120 seconds
Cannot open the file /mnt/application/ha/InheritedApCount.txt
Cannot open the file /mnt/application/ha/InheritedApCount.txt
Please help with all possible suggestions. thanks in advance

Hi,
i cant see that you have permenant AP count license on both.
review the following document for licensing requirement on AP SSO
http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bd3504.shtml#licensing

Form for edit pair table

Hi,
my problem is how to create edit form for pair two tables for example COMPANIES and CAMPAIGNS.
create table COMPANIES (
id integer,
name varchar2(100));
create table CAMPAIGNS (
id integer,
name varchar2(100));
create table PAIRS (
id_company integer,
id_campaign integer);
And the problem is which wizard to edit user friendly (it is important) table PAIRS. My idea is to select certain campaign and then filter companies based on filter critera and then by unselecting checkbox be able to delete specified companies.
Thanks
sasa

See the search results at
http://forums.oracle.com/forums/search.jspa?objID=f137&q=tabular+form+%22intersection+table%22

Active/Standby Failover with pair of 5510s and redundant L2 links

Hi
I just got two ASA5510-SEC-BUN-K9 and I'm wondering is it possible to implement an Active/Standby Failover configuration (Routed mode) with two ASA5510 and redundant pair of switches from both inside and outside interfaces? In other words, I would like to have two L2 links from each ASA (in pair od ASAa) to each L2 switch (in pair of redundant L2 Switches). The configuration I would like to achive is just like one in Cisco Security Appliance Command Line Configuration Guide, page B-23, figure B-8, with only difference that I wouldn't go with multiple security contexts (I want Active/Standby failover).
Thanks in advance
Zoran Milenkovic

Hello Zoran,
Absolutely. You can have 2 ASAs configured in Active/Standby mode. For reference, here is a link which has a network connectivity diagram based on PIX, however, connectivity would still be same with ASAs-
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/failover.html#wp1053462
The difference is that on ASA, you can only have LAN-Based failover, hence you'll need to use one additional interface on both ASAs for failover-link. You can connect these two failover-link interfaces directly using a cross cable.
Apart from this, please refer to following link on how to go with configuration of Lan-based Active/Standby failover-
http://www.cisco.com/en/US/docs/security/asa/asa72/configuration/guide/failover.html#wp1064158
Also make sure that both ASAs have required hardware/software/license based on following link-
http://www.cisco.com/en/US/docs/security/asa/asa72/configuration/guide/failover.html#wp1047269
Hope this helps.
Regards,
Vibhor.

Cisco 5508 HA VS Primary/Secondary- Feedback

Anyone having issues with 5508 HA switching between the pair? Would you say that the Primary/secondary fail over is good enough?

Hi Leo, Scott
So I was doing a bit more reading on this http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/69639-wlc-failover.html it is an old document but working through it the document suggested that you didn't need to specify the IP address of the Primary or Secondary controller in the Wireless -> All AP -> AP_NAME -> High Availability. I removed this from one of the APs that was at the time serving no clients and tried to move it to the secondary and it worked. I then moved it back to the primary and it worked again.
Any reason why this would happen? The IP addresses I was using were 100% correct. The only difference I see for this controller as opposed to others we manage is the introduction of new interface types i.e. 'redundancy management' , 'redundancy port' ,etc. I do not have redundancy enabled so I'm guessing not, but having trawled through the configuration this is the only difference I can see?

Software upgrades on HA Pairs?

I am working on a plan to convert some of my existing 5508s to be HA pairs. I like the redundancy i have now with multiple controllers, but don't necessarily like buying two licenses for every AP. I am trying to determine the downside to the HA mode. I am trying to figure out what a code upgrade looks like for a redundant pair. Currently, because I have 2 licenses for each AP, I have this process:
1. Load new code onto both controllers (no reboot here)
2. move the APs from controller A to controller B,
3. Reboot controller A to new code
4. Predownload new code from controller B to APs
5. Slowly move APs back to controller A so that there is no real outage. Clients move to adjacent APs as each AP is individually rebooted.
Is there a way I can take an HA member out of service, upgrade it and move the APs to it before doing the other HA member? Or does the whole HA pair have to be down to facilitate a code upgrade? Curious to hear what others are doing.
Thanks

Before you convert the WLC to HA, make sure all the bootstrap have been upgraded. If you have any certificates and/or web-auth pages, make sure they are loaded to both before you tie them up into an HA.
Next, your license for the 2nd unit. Send an email to [email protected] and provide the HA serial number. Tell them you want to convert this unit to HA SSO. They'll send you further instructions.
Ok, now the HA bit. Choose a firmware, either 7.4.121.X or 7.6.110.X. Don't choose anything else.
Read through the High Availability (SSO) Deployment Guide and pay close attention to mandatory requirements especially the requirement that both 5508 must be physically connected via the RP port.
Let us know how you go.

Cannot pair new Apple TV with iTunes

Okay I recently got the new Apple TV 160GB model and have it connected to Internet over Wifi. The computer whose iTunes Library I want to pair it with is a 2006 based Intel Mac Mini with Core Duo 1 processor and Mac OS X Tiger 10.4.11 with iTunes 8.2.1 presently installed.
The Apple TV had 2.3.1 installed when it arrived -- tried pairing with iTunes while running Apple TV 2.3.1 on the Apple TV didn't work. Updated to 2.4 still doesn't work. Unfortunately I've been unable to get the Mac Mini to connect to the Internet over my home wireless network and stay connected -- it has connected a few times but shortly loses the connection. Other times I try to connect while disconnected and get errors that it could not connect.
Regardless, the few times I did manage to connect over Wifi my Mac Mini would not recognize my Apple TV (has never been paired with iTunes so has not even been named) we use a Linksys wireless router for wireless Internet.
At times the wireless Internet connection in my bedroom where I keep the Apple TV and Mac Mini has been unreliable -- when using my iPod Touch I also own with Internet access any time I am using it in my bedroom the Wifi access quickly gets lost -- to reconnect have to venture out into the hallway then come back the room and get some Wifi use within the room for about 2 minutes before losing the connection again.
However, my Apple TV in my bedroom once connected has had no problem staying connected to the wireless network neither does the Nintendo Wii I own. Also my new MacBook Pro can connect to the Internet wirelessly within the bedroom and often stay connected -- although a few times even when using MacBook Pro the connection gets lost and I go outside the room and connection is restored.
Anyways even when I manage to get the Mac Mini on the wireless network iTunes is unable to recognize and pair my Apple TV. In the past I have gotten it to recognize my iPod Touch as a wireless remote and use Apple's Remote app and/or the Rowmote Pro app from Apple's iPhone App Store with it -- only recently they aren't showing up either due to connection problems of the Mac Mini accessing the wireless network.
Whenever the Mac Mini does connect to the wireless network it only stays connected a brief time and then is hard to get it to reconnect. Last time it connected I feel I got lucky and I'm not superstitious so I wouldn't believe in being lucky or unlucky.
Anyways, when the Mac Mini has connected wirelessly even then it does not recognize the Apple TV. This Apple TV has never been synced to before or streamed to. The only thing I've been able to use it for so far is accessing iTunes Store on the TV and accessing YouTube.
All my purchases are on the Mac Mini though and don't want to have to re-purchase them from Apple TV and download to it. In any case whether I bought some content from Apple TV or not (would not want to have to re-buy all of it) I should be able to get Apple TV to be recognized with iTunes.
At present the Mac Mini which I'm using to type and send this is connected over a wired Ethernet network and the Apple TV is connected over Wifi. I've tried going into the Firewall and ensuring the port for iTunes Music Sharing is enabled, and UDP port 5353 as noted by an Apple Support document online for Bonjour Networking is enabled. I've tried restarting the Mac Mini but Apple TV just won't show up in iTunes at all even when the Mac Mini was also on the wireless network.

Update: My Apple TV is connected via Wifi but Mini via Ethernet and Mini does not seem to recognize Apple TV unless Mini also has Wifi or unless I run Ethernet cord from Mini directly to Apple TV at which point they are physically connected to each other but neither has Internet.
I think there is a problem with my Mini's Airport card -- yesterday for the first time in over a month I managed to get it to connect wirelessly again and keep it connected for a few hours (during which time Apple TV showed up in the devices list on Mac Mini's iTunes Library) but after that it lost the connection and have been struggling ever since to get it reconnected. Have posted on the Mac Mini, Mac Mini (previous early 2009 models) Internet & Networking with Mac Mini discussion forum by Apple for help and now the Airport Extreme section of Apple Discussions.
Thanks for the help -- I now know this is not a problem with the Apple TV it is likely a hardware issue with Mini's Airport card and as it is out of warranty now would unfortunately have to pay to get it repaired.

5508 unable to form redundant pair

Similar Messages

Maybe you are looking for