5508 Wireless

On the 5508 controller there seems to be a lot of certificates that can be installed.  Is there an up to date article that covers all of them?
commands->download file to controller   (vendor CA certificate)
                                                                 (vendor device certificate)   MUST BE IN PEM format
management->http-https:  (X) ssl     cert   
security->web auth->   (x) ssl cert      
When using OPenssl 9.8h I seemed like the only way I could create the request file was to not have a password (I was receiving memory alloc error when a password was specifed)
req -new -newkey rsa:2048 -nodes -keyout mykey.pem -out myreq.pem -config c:\openssl\share\openssl.cnf      
                          REM   creates the  mykey.pem and myreq.pem files
combine the certs together in a file called all-certs.pem
order is
device
intermediate
root
openssl>pkcs12 -export -in All-certs.pem -inkey mykey.pem -out All-certs.p12 -clcerts -passin pass:check123 -passout pass:check123
openssl>pkcs12 -in All-certs.p12 -out final-cert.pem -passin pass:check123 -passout pass:check123
output--->      MAC verified OK
download (ssl)      final-cert.pem  to controller

Hi,
I am not sure of the Article but their use is straight forward.
commands->download file to controller   (vendor CA certificate)
                                                                 (vendor device certificate)   MUST BE IN PEM format
Here device certificate and server certificate can be uploaded. Use case is EAP-TLS support when WLC is acting like a radius server. It needs to present its certificate and also validate client certificate when they present the same.So needs two certificates.
management->http-https:  (X) ssl     cert   
Here it just needs to present the certificate so that your browser doesnt give the warning.Go to Management >https..to upload certificate for this purpose.
security->web auth->   (x) ssl cert
This certificate would be presented during web-auth when Internal web-server of the WLC is hit and you dont want warning because of that in your browser.Go to Security >web-auth>certificate to upload this certificate. This is attached to the virtual ip.From 7.6 onwards ..it has to be fully chained.
Additionally you can force WLC to use device certificate as HTTPS management certificate using the command:
(WLC) >config certificate use-device-certificate ?
webadmin       Use device certificate for web administration
Regards
Dhiresh
**Please rate helpful posts**

Similar Messages

  • Adding second 5508 Wireless Controller, how to best configure for load balancing and redundancy?

    We recently purchased a second 5508 wireless controller (both licensed for 100+ AP's).  What is the easiest way to configure and add the second controller so I can split the load between the 2 controllers and provide failover capability?  I do not want to run in an active/standby mode since that will effectively cut our AP capacity by half even with both controllers running. 
    Should I just manually configure the new controller (long and drawn out process to configure all the parameters), backup the current controller configuration and import to the second controller (then change the ip address) or is their an easier way to cause the two controllers to synchronize the configurations? 
    We are currently running 7.0.240.0 on our active controller and I would rather not upgrade it until we get the new controller online so I can have less downtime and fail AP's between controllers.
    What can you recommend? 
    Jim

    I'm assuming then, when I update the software on the controllers I won't be able to choose which controller is primary for an AP anymore and will lose access to the 100 AP licenses (and the capability to have 100 AP's registered, 100 licenses on each Controller).
    Read the Deployment Guide.  It should mention that you can choose which controller is the "primary" and which one is the "secondary".
    If I'm not concerned about quick failover can I still assign a primary and secondary controller for each AP and utilize all 200 AP licenses that are split between the 2 controllers?
    You sure can.  But this "old school" method is a very expensive method.  Why?  Because this means that you have two controllers with similar AP licenses.  The newer AP SSO means one controller has a full license and the other has only an HA SSO license, which is a lot cheaper.

  • Cisco 5508 Wireless Controller in HA mode

    Hello,
    is there a support of 1+1 mode (HA mode) at 5508 Controller?
    If yes Is there a HA bundle or do we have to order two identical 5508 controller ?
    Thanks for response.
    Richard

    Hello Richard,
    FYI, WLC 7.3 has been released that includes HA features. Following are the links for your reference,
    https://supportforums.cisco.com/docs/DOC-26827
    http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps10315/qa_c67-714540.html
    http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bd3504.shtml#req

  • Cisco WLC 5508 Wireless Outdoor Mesh

    I noticed that the 5508 requires a plus license feature upgrade in order to support Enterprise Wireless Mesh. My understanding is that enterprise wireless mesh is indoor wireless mesh support. Will the 5508 support outdoor wireless mesh without the plus license feature set?
    Thanks in advance

    "Enterprise Wireless Mesh" should just refer to Indoor Mesh.
    The 1520's are Mesh only devices and aren't part of the Enterprise Wireless Mesh. So, as far as I know, the 1520s are fully supported in the 5508.
    Unfortunately, I do not have any supporting information to back this up.

  • Cisco 5508 Wireless Controller with Splash Page Disclaimer

    How do one configure a splash disclaimer page on a Cisco Wireless Controller 5508 with no authentication?
    Jimmy

    There are many options to you in this scenario, but if you're looking to simply provide a splash page via the WLC without interacting with any other web servers, you can configure Local Web Authentication (LWA) as seen in this configuration example.
    http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html?referring_site=RE&pos=1&page=http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71881-ext-web-auth-wlc.html
    If you are not wanting the authentication, you can choose the "passthrough" method which will not require any credentials, only accepting an AUP or whatever you want.

  • Cheaper solution for a 5508 wireless lan based

    Hello, our wireless lan is based on a single 5508 (It's not HA). We would like to use a cheaper solution as a backup if this 5508 falls. Could 2504 works?
    In short words, we have two RAP's that are connected in a hp switch and all ap's are connected to these rap's. Same for wlc, it's connected to switch

    Have you checked Radio Shack? The staff are pretty knowledgeable about what you need to connect MBPs to TVs. Their cables are way less than $300.
    !http://i50.tinypic.com/izvwo1.gif!

  • Problem getting Airprint (Bonjour) to communicate to HP LaserJet CP1525nw printer across a Cisco 5508 Wireless Controller

    I cannot get my IPad2 to print (it cannot find the printer) using a Laserjet CP1525nw color printer across a wireless network using a Cisco 1508 Wireless Controller with 49 wireless access points. HELP!!!!
    What is the secret to getting Bonjour to work on it?
    I can get the IPad2 to locate the HP CP1525nw printer without a hitch using a low budget Netgear WAG102 stand alone wireless access point on the same network.

    If it helps somebody, here is what you need to do.
    It worked for me, but only in Multicast-Unicast mode.
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0 080bb1d7c.shtml

  • Redirect to web authentication not working on Cisco 5508 Wireless Controller

    Hi,
    I have a wlan with web authentication:
    http://i55.tinypic.com/w145zk.png
    and
    http://i51.tinypic.com/344sfm0.png
    When I connect to  the SSID (I get correct IP from the Cisco 5508 Controller) and try to  surf, I do not get redirected to the web authentication page (https://1.1.1.1/login.html), when I manually insert the URL I get "cannot display the webpage". Any idea?
    The virtual interface is 1.1.1.1.
    Here is a screenshot of interface and internal dhcp:
    http://i52.tinypic.com/2vkm1d2.png
    Any idea why clients are not redirecting?
    Thanks!

    Thanks for the reply dmantil!
    When I changed the Virtual DNS name to 1.1.1.1 (the same as the IP) I get redirected if I use http://198.133.219.25, but not with http://cisco.com, I get redirected only if I use IP.
    I forgot to mention that the controller is in a lab with no access to DNS server. Does the controller check if the domain is valid before redirecting users? I cant find any documentation on how the controller redirect users.

  • 5508 Wireless Lan Controller

    I have been monitoring the alarm summary but have been off couple days and i see one of my controllers is down.  Getting  critical level security and message is port is down on the controller, condition link down.  The other issue is config difference found between NCS and Contoller, I tried getting them to sync together but still getting the same message.                  

    Alvina:
    can you login to the controller directly? open the GUI (or CLI) and login?
    Try to audit the WLC configuration and see what are the exact config that differs.
    Regards,
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • 5508 wireless controller - and limit SSID's

    I am trying to figure out if I can limit some of my access points to only some SSIDs available – instead of everything that’s available on the controller?

    You might find this helpful
    http://www.my80211.com/cisco-wlc-labs/2009/3/22/cisco-ap-group-nugget.html
    I blogged about this and did a video to help
    "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
    ‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

  • Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?

    Hi!
    I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
    I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
    Log from AP:
    using ÿÿÿÿ ddr static values from serial eeprom
    ddr init done
    Running Normal Memtest...
    Passed.
    IOS Bootloader - Starting system.
    FLASH CHIP:  Numonyx P33
    Checking for Over Erased blocks
    Xmodem file system is available.
    DDR values used from system serial eeprom.
    WRDTR,CLKTR: 0x83000800, 0xc0000000
    RQDC, RFDC : 0x80000037, 0x00000184
    PCIE0: link is up.
    PCIE0: VC0 is active
    PCIE1: link is NOT up.
    PCIE1 port 1 not initialize
    PCIEx: initialization done
    flashfs[0]: 6 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 32385024
    flashfs[0]: Bytes used: 2369024
    flashfs[0]: Bytes available: 30016000
    flashfs[0]: flashfs fsck took 21 seconds.
    Reading cookie from system serial eeprom...Done
    Base Ethernet MAC address: 44:2b:03:dc:09:25
    Ethernet speed is 1000 Mb - FULL duplex
    Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
    File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
    y point: 0x4000
    executing...
    enet halted
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
    SE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 01-Jun-10 12:53 by prod_rel_team
    Proceeding with system init
    Proceeding to unmask interrupts
    Initializing flashfs...
    FLASH CHIP:  Numonyx P33
    Checking for Over Erased blocks
    flashfs[1]: 6 files, 2 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 32126976
    flashfs[1]: Bytes used: 2369024
    flashfs[1]: Bytes available: 29757952
    flashfs[1]: flashfs fsck took 7 seconds.
    flashfs[1]: Initialization complete.
    flashfs[2]: 0 files, 1 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 11999232
    flashfs[2]: Bytes used: 1024
    flashfs[2]: Bytes available: 11998208
    flashfs[2]: flashfs fsck took 1 seconds.
    flashfs[2]: Initialization complete....done Initializing flashfs.
    Ethernet speed is 1000 Mb - FULL duplex
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-LAP1041N-E-K9    (PowerPC405ex) processor (revision B0) with 98294K/32
    768K bytes of memory.
    Processor board ID FCZ1611W414
    PowerPC405ex CPU at 333Mhz, revision number 0x147E
    Last reset from reload
    LWAPP image version 7.0.94.21
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 44:2B:03:DC:09:25
    Part Number                          : 73-14034-04
    PCA Assembly Number                  : 800-34273-05
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC16075VZ3
    Top Assembly Part Number             : 800-34284-03
    Top Assembly Serial Number           : FCZ1611W414
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1041N-E-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:00:09.574: *** CRASH_LOG = YES
    Base Ethernet MAC address: 44:2B:03:DC:09:25
    *Mar  1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
    (contains, 1024 messages)
    *Mar  1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
    to up
    *Mar  1 00:00:11.892: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
    SE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 01-Jun-10 12:53 by prod_rel_team
    *Mar  1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
    ernet0, changed state to up
    logging facility kern
            ^
    % Invalid input detected at '^' marker.
    *Mar  1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
    LER
    *Mar  1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
    IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
    *Mar  1 00:09:08.282:  -Verify the required power-injector is installed on this
    port: AIR-CT5508-K9(Gig 0/0/2).
    *Mar  1 00:09:08.282:  -If a power-injector is installed, issue the command:"pow
    er inline negotiation injector installed"
    *Mar  1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
    static IP. Forcing AP to use DHCP.
    *Mar  1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    Not in Bound state.
    *Mar  1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
    . Renewing DHCP IP.
    logs from wireless controller:
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Gu
    est
    ap-manager                       2    untagged 209.165.200.231 Dynamic Yes    No
    management                       1    untagged 209.165.200.230 Static  Yes    No
    service-port                     N/A  N/A      192.168.1.157   Static  No     No
    virtual                          N/A  N/A      1.1.1.1         Static  No     No
    (Cisco Controller) >
    i conect with service-port ok  and the management port works, i think.
    AP442b.03dc.0925>ping 209.165.200.230
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
    Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
    AP442b.03dc.0925>
    Help, please!
    i write in spanish:
    Hola:
    Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, Gracias

    Hi!
    I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by  DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
    I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
    Before the logs, I see this message from AP:
    *Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
    version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC? 
    Hola:
    He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
    Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
    Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
    *Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
    version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC? 
    Un saludo
    Antonio R.
    (Cisco Controller) >show run-config
    Press Enter to continue...
    System Inventory
    NAME: "Chassis"    , DESCR: "Cisco Wireless Controller"
    PID: AIR-CT5508-K9,  VID: V02,  SN: FCW1608L05X
    Burned-in MAC Address............................ C4:64:13:8F:93:40
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 25
    Press Enter to continue or to abort
    System Information
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 6.0.199.4
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console
    1.27
    Build Type....................................... DATA + WPS
    System Name...................................... CISCO-CAPWAP-CONTROLLER
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 209.165.200.230
    Last Reset....................................... Power on reset
    System Up Time................................... 0 days 0 hrs 17 mins 45 secs
    System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
    Rome, Vienna
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... ES  - Spain
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    External Temperature............................. +23 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Disabled
    Number of WLANs.................................. 1
    3rd Party Access Point Support................... Disabled
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ C4:64:13:8F:93:40
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 25
    Press Enter to continue or to abort
    Switch Configuration
    802.3x Flow Control Mode......................... Disable
    FIPS prerequisite features....................... Disabled
    secret obfuscation............................... Enabled
    Network Information
    RF-Network Name............................. hosp
    Web Mode.................................... Disable
    Secure Web Mode............................. Enable
    Secure Web Mode Cipher-Option High.......... Disable
    Secure Web Mode Cipher-Option SSLv2......... Enable
    Secure Shell (ssh).......................... Enable
    Telnet...................................... Disable
    Ethernet Multicast Forwarding............... Disable
    Ethernet Broadcast Forwarding............... Disable
    AP Multicast/Broadcast Mode................. Unicast
    IGMP snooping............................... Disabled
    IGMP timeout................................ 60 seconds
    User Idle Timeout........................... 300 seconds
    ARP Idle Timeout............................ 300 seconds
    Cisco AP Default Master..................... Enabled
    AP Join Priority............................ Disable
    Mgmt Via Wireless Interface................. Disable
    Mgmt Via Dynamic Interface.................. Disable
    Bridge MAC filter Config.................... Enable
    Bridge Security Mode........................ EAP
    Mesh Full Sector DFS........................ Enable
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
    AP Fallback ................................ Enable
    Web Auth Redirect Ports .................... 80
    Fast SSID Change ........................... Disabled
    IP/MAC Addr Binding Check .................. Enabled
    Press Enter to continue or to abort
    Port Summary
               STP   Admin   Physical   Physical   Link   Link
    Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE    SFPType
    1  Normal  Forw Enable  Auto       1000 Full  Up     Enable  N/A     1000BaseTX
    2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    3  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    4  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    5  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    6  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    7  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    8  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A     Not Present
    Press Enter to continue or to abort
    AP Summary
    Number of APs.................................... 0
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name             Slots  AP Model             Ethernet MAC       Location
         Port  Country  Priority
    Press Enter to continue or to abort
    Press Enter to continue or to abort
    AP Location
    Site Name........................................ default-group
    Site Description.................................
    WLAN ID          Interface          Network Admission Control
    1               management           Disabled
    AP Name             Slots  AP Model             Ethernet MAC       Location
         Port  Country  Priority  GroupName
    Press Enter to continue or to abort
    AP Config
    Press Enter to continue or to abort
    Press Enter to continue or to abort
    AP Airewave Director Configuration
    Press Enter to continue or to abort
    802.11a Configuration
    802.11a Network.................................. Disabled
    11nSupport....................................... Enabled
          802.11a Low Band........................... Enabled
          802.11a Mid Band........................... Enabled
          802.11a High Band.......................... Enabled
    802.11a Operational Rates
        802.11a 6M Rate.............................. Mandatory
        802.11a 9M Rate.............................. Supported
        802.11a 12M Rate............................. Mandatory
        802.11a 18M Rate............................. Supported
        802.11a 24M Rate............................. Mandatory
        802.11a 36M Rate............................. Supported
        802.11a 48M Rate............................. Supported
        802.11a 54M Rate............................. Supported
    802.11n MCS Settings:
        MCS 0........................................ Supported
        MCS 1........................................ Supported
        MCS 2........................................ Supported
        MCS 3........................................ Supported
        MCS 4........................................ Supported
        MCS 5........................................ Supported
        MCS 6........................................ Supported
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
        MCS 7........................................ Supported
        MCS 8........................................ Supported
        MCS 9........................................ Supported
        MCS 10....................................... Supported
        MCS 11....................................... Supported
        MCS 12....................................... Supported
        MCS 13....................................... Supported
        MCS 14....................................... Supported
        MCS 15....................................... Supported
    802.11n Status:
        A-MPDU Tx:
            Priority 0............................... Enabled
            Priority 1............................... Disabled
            Priority 2............................... Disabled
            Priority 3............................... Disabled
            Priority 4............................... Disabled
            Priority 5............................... Disabled
            Priority 6............................... Disabled
            Priority 7............................... Disabled
    Beacon Interval.................................. 100
    CF Pollable mandatory............................ Disabled
    CF Poll Request mandatory........................ Disabled
    CFP Period....................................... 4
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
    CFP Maximum Duration............................. 60
    Default Channel.................................. 36
    Default Tx Power Level........................... 0
    DTPC  Status..................................... Enabled
    Fragmentation Threshold.......................... 2346
    TI Threshold..................................... -50
    Legacy Tx Beamforming setting.................... Disabled
    Traffic Stream Metrics Status.................... Disabled
    Expedited BW Request Status...................... Disabled
    World Mode....................................... Enabled
    EDCA profile type................................ default-wmm
    Voice MAC optimization status.................... Disabled
    Call Admision Control (CAC) configuration
    Voice AC:
       Voice AC - Admission control (ACM)............ Disabled
       Voice max RF bandwidth........................ 75
       Voice reserved roaming bandwidth.............. 6
       Voice load-based CAC mode..................... Disabled
       Voice tspec inactivity timeout................ Disabled
       Voice Stream-Size............................. 84000
       Voice Max-Streams............................. 2
    Video AC:
       Video AC - Admission control (ACM)............ Disabled
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
       Video max RF bandwidth........................ Infinite
       Video reserved roaming bandwidth.............. 0
    Press Enter to continue or to abort
    802.11a Advanced Configuration
    Press Enter to continue or to abort
    802.11a Airewave Director Configuration
    RF Event and Performance Logging
      Channel Update Logging......................... Off
      Coverage Profile Logging....................... Off
      Foreign Profile Logging........................ Off
      Load Profile Logging........................... Off
      Noise Profile Logging.......................... Off
      Performance Profile Logging.................... Off
      TxPower Update Logging......................... Off
    Default 802.11a AP performance profiles
      802.11a Global Interference threshold.......... 10 %
      802.11a Global noise threshold................. -70 dBm
      802.11a Global RF utilization threshold........ 80 %
      802.11a Global throughput threshold............ 1000000 bps
      802.11a Global clients threshold............... 12 clients
    Default 802.11a AP monitoring
      802.11a Monitor Mode........................... enable
      802.11a Monitor Mode for Mesh AP Backhaul...... disable
      802.11a Monitor Channels....................... Country channels
      802.11a AP Coverage Interval................... 180 seconds
      802.11a AP Load Interval....................... 60 seconds
      802.11a AP Noise Interval...................... 180 seconds
    --More or (q)uit current module or to abort
    --More or (q)uit current module or to abort
      802.11a AP Signal Strength Interval............ 60 seconds
    Automatic Transmit Power Assignment
      Transmit Power Assignment Mode................. AUTO
      Transmit Power Update Interval................. 600 seconds
      Transmit Power Threshold....................... -70 dBm
      Transmit Power Neighbor Count.................. 3 APs
      Min Transmit Power............................. -10 dBm
      Max Transmit Power............................. 30 dBm
      Transmit Power Update Contribution............. SNI.
      Transmit Power Assignment Leader............... c4:64:13:8f:93:40
      Last Run....................................... 75 seconds ago
    Coverage Hole Detection
      802.11a Coverage Hole Detection Mode........... Enabled
      802.11a Coverage Voice Packet Count............ 100 packets
      802.11a Coverage Voice Packet Percentage....... 50%
      802.11a Coverage Voice RSSI Threshold.......... -80 dBm
      802.11a Coverage Data Packet Count............. 50 packets
      802.11a Coverage Data Packet Percentage........ 50%
      802.11a Coverage Data RSSI Threshold........... -80 dBm
      802.11a Global coverage exception level........ 25 %
      802.11a Global client minimum exception lev.... 3 clients
    Automatic Channel Assignment
      Channel Assignment Mode........................ AUTO
    --More or (q)uit current module or to abort
      Channel Update Interval........................ 600 seconds [startup]
      Anchor time (Hour of the day).................. 0
      Channel Update Contribution.................... SNI.
      Channel Assignment Leader...................... c4:64:13:8f:93:40
      Last Run....................................... 75 seconds ago
      DCA Sensitivity Level.......................... STARTUP (5 dB)
      DCA 802.11n Channel Width...................... 20 MHz
      DCA Minimum Energy Limit....................... -95 dBm
      Channel Energy Levels
        Minimum...................................... unknown
        Average...................................... unknown
        Maximum...................................... unknown
      Channel Dwell Times
        Minimum...................................... unknown
        Average...................................... unknown
        Maximum...................................... unknown
      802.11a 5 GHz Auto-RF Channel List
        Allowed Channel List......................... 36,40,44,48,52,56,60,64
        Unused Channel List.......................... 100,104,108,112,116,120,124,
                                                      128,132,136,140
      DCA Outdoor AP option.......................... Disabled
    Radio RF Grouping
      802.11a Group Mode............................. AUTO
    --More or (q)uit current module or to abort
      802.11a Group Update Interval.................. 600 seconds
      802.11a Group Leader........................... c4:64:13:8f:93:40
        802.11a Group Member......................... c4:64:13:8f:93:40
      802.11a Last Run............................... 75 seconds ago
    802.11b Configuration
    802.11b Network.................................. Enabled
    11gSupport....................................... Enabled
    11nSupport....................................... Enabled
    802.11b/g Operational Rates
        802.11b/g 1M Rate............................ Mandatory
        802.11b/g 2M Rate............................ Mandatory
        802.11b/g 5.5M Rate.......................... Mandatory
        802.11b/g 11M Rate........................... Mandatory
        802.11g 6M Rate.............................. Supported
        802.11g 9M Rate.............................. Supported
        802.11g 12M Rate............................. Supported
        802.11g 18M Rate............................. Supported
        802.11g 24M Rate............................. Supported
        802.11g 36M Rate............................. Supported
        802.11g 48M Rate............................. Supported
        802.11g 54M Rate............................. Supported
    802.11n MCS Settings:
        MCS 0........................................ Supported
        MCS 1........................................ Supported
        MCS 2........................................ Supported
        MCS 3........................................ Supported
        MCS 4........................................ Supported
    --More or (q)uit current module or to abort
        MCS 5........................................ Supported
        MCS 6........................................ Supported
        MCS 7........................................ Supported
        MCS 8........................................ Supported
        MCS 9........................................ Supported
        MCS 10....................................... Supported
        MCS 11....................................... Supported
        MCS 12....................................... Supported
        MCS 13....................................... Supported
        MCS 14....................................... Supported
        MCS 15....................................... Supported
    802.11n Status:
        A-MPDU Tx:
            Priority 0............................... Enabled
            Priority 1............................... Disabled
            Priority 2............................... Disabled
            Priority 3............................... Disabled
            Priority 4............................... Disabled
            Priority 5............................... Disabled
            Priority 6............................... Disabled
            Priority 7............................... Disabled
    Beacon Interval.................................. 100
    CF Pollable mode................................. Disabled
    --More or (q)uit current module or to abort
    CF Poll Request mandatory........................ Disabled
    CFP Period....................................... 4
    CFP Maximum Duration............................. 60
    Default Channel.................................. 1
    Default Tx Power Level........................... 0
    DTPC  Status..................................... Enabled
    Call Admission Limit  ........................... 105
    G711 CU Quantum ................................. 15
    ED Threshold..................................... -50
    Fragmentation Threshold.......................... 2346
    PBCC mandatory................................... Disabled
    RTS Threshold.................................... 2347
    Short Preamble mandatory......................... Enabled
    Short Retry Limit................................ 7
    Legacy Tx Beamforming setting.................... Enabled
    Traffic Stream Metrics Status.................... Disabled
    Expedited BW Request Status...................... Disabled
    World Mode....................................... Enabled
    Faster Carrier Tracking Loop..................... Disabled
    EDCA profile type................................ default-wmm
    Voice MAC optimization status.................... Disabled
    Call Admision Control (CAC) configuration
       Voice AC - Admission control (ACM)............ Disabled
    --More or (q)uit current module or to abort
       Voice Stream-Size............................. 84000
       Voice Max-Streams............................. 2
       Voice max RF bandwidth........................ 75
       Voice reserved roaming bandwidth.............. 6
       Voice load-based CAC mode..................... Disabled
       Voice tspec inactivity timeout................ Disabled
       Video AC - Admission control (ACM)............ Disabled
       Video max RF bandwidth........................ 50
       Video reserved roaming bandwidth.............. 0
    802.11b Advanced Configuration
    Press Enter to continue or to abort
    802.11b Airewave Director Configuration
    RF Event and Performance Logging
      Channel Update Logging......................... Off
      Coverage Profile Logging....................... Off
      Foreign Profile Logging........................ Off
      Load Profile Logging........................... Off
      Noise Profile Logging.......................... Off
      Performance Profile Logging.................... Off
      Transmit Power Update Logging.................. Off
    Default 802.11b AP performance profiles
      802.11b Global Interference threshold.......... 10 %
      802.11b Global noise threshold................. -70 dBm
      802.11b Global RF utilization threshold........ 80 %
      802.11b Global throughput threshold............ 1000000 bps
      802.11b Global clients threshold............... 12 clients
    Default 802.11b AP monitoring
      802.11b Monitor Mode........................... enable
      802.11b Monitor Channels....................... Country channels
      802.11b AP Coverage Interval................... 180 seconds
      802.11b AP Load Interval....................... 60 seconds
      802.11b AP Noise Interval...................... 180 seconds
      802.11b AP Signal Strength Interval............ 60 seconds
    Automatic Transmit Power Assignment
      Transmit Power Assignment Mode................. AUTO
      Transmit Power Update Interval................. 600 seconds
      Transmit Power Threshold....................... -70 dBm
      Transmit Power Neighbor Count.................. 3 APs
      Min Transmit Power............................. -10 dBm
      Max Transmit Power............................. 30 dBm
      Transmit Power Update Contribution............. SNI.
      Transmit Power Assignment Leader............... c4:64:13:8f:93:40
      Last Run....................................... 213 seconds ago
    Coverage Hole Detection
      802.11b Coverage Hole Detection Mode........... Enabled
      802.11b Coverage Voice Packet Count............ 100 packets
      802.11b Coverage Voice Packet Percentage....... 50%
      802.11b Coverage Voice RSSI Threshold.......... -80 dBm
      802.11b Coverage Data Packet Count............. 50 packets
      802.11b Coverage Data Packet Percentage........ 50%
      802.11b Coverage Data RSSI Threshold........... -80 dBm
      802.11b Global coverage exception level........ 25 %
      802.11b Global client minimum exception lev.... 3 clients
    Automatic Channel Assignment
      Channel Assignment Mode........................ AUTO
      Channel Update Interval........................ 600 seconds [startup]
      Anchor time (Hour of the day).................. 0
      Channel Update Contribution.................... SNI.
      Channel Assignment Leader...................... c4:64:13:8f:93:40
      Last Run....................................... 213 seconds ago
      DCA Sensitivity Level: ...................... STARTUP (5 dB)
      DCA Minimum Energy Limit....................... -95 dBm
      Channel Energy Levels
        Minimum...................................... unknown
        Average...................................... unknown
        Maximum...................................... unknown
      Channel Dwell Times
        Minimum...................................... unknown
        Average...................................... unknown
        Maximum...................................... unknown
      802.11b Auto-RF Allowed Channel List........... 1,6,11
      Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
    Radio RF Grouping
      802.11b Group Mode............................. AUTO
      802.11b Group Update Interval.................. 600 seconds
      802.11b Group Leader........................... c4:64:13:8f:93:40
        802.11b Group Member......................... c4:64:13:8f:93:40
      802.11b Last Run............................... 213 seconds ago
    Mobility Configuration
    Symmetric Mobility Tunneling (current) .......... Enabled
    Symmetric Mobility Tunneling (after reboot) ..... Enabled
    Mobility Protocol Port........................... 16666
    Default Mobility Domain.......................... hosp
    Multicast Mode .................................. Disabled
    Mobility Domain ID for 802.11r................... 0x97e2
    Mobility Keepalive Interval...................... 10
    Mobility Keepalive Count......................... 3
    Mobility Group Members Configured................ 1
    Mobility Control Message DSCP Value.............. 0
    Controllers configured in the Mobility Group
    MAC Address        IP Address       Group Name                        Multicast
    IP     Status
    c4:64:13:8f:93:40  209.165.200.230  hosp                              0.0.0.0
            Up
    Advanced Configuration
    Probe request filtering..........................  Enabled
    Probes fwd to controller per client per radio....  0
    Probe request rate-limiting interval.............  500 msec
    EAP-Identity-Request Timeout (seconds)........... 30
    EAP-Identity-Request Max Retries................. 2
    EAP Key-Index for Dynamic WEP.................... 0
    EAP Max-Login Ignore Identity Response........... enable
    EAP-Request Timeout (seconds).................... 30
    EAP-Request Max Retries.......................... 2
    EAPOL-Key Timeout (milliseconds)................. 1000
    EAPOL-Key Max Retries............................ 2
    dot11-padding.................................... Disabled
    Authentication Response Timeout (seconds)........ 10
    Rogue Entry Timeout (seconds).................... 1200
    AP Heart Beat Timeout (seconds).................. 30
    AP Discovery Timeout (seconds)................... 10
    AP Local mode Fast Heartbeat (seconds)........... disable
    AP Hreap mode Fast Heartbeat (seconds)........... disable
    AP Primary Discovery Timeout (seconds)........... 120
    AP Primed Join Timeout (seconds)................. 0
    Packet Forwarding watchdog timer (seconds)....... 240 (enable)
    Location Configuration
    RFID Tag data Collection......................... Enabled
    RFID  timeout.................................... 1200 seconds
    RFID mobility.................................... Oui:00:14:7e : Vendor:pango  S
    tate:Disabled
    Interface Configuration
    Interface Name................................... management
    MAC Address...................................... c4:64:13:8f:93:40
    IP Address....................................... 209.165.200.230
    IP Netmask....................................... 255.255.255.0
    IP Gateway....................................... 209.165.200.1
    External NAT IP State............................ Disabled
    External NAT IP Address.......................... 192.168.1.1
    VLAN............................................. untagged
    Quarantine-vlan.................................. 0
    Active Physical Port............................. 1
    Primary Physical Port............................ 1
    Backup Physical Port............................. Unconfigured
    Primary DHCP Server.............................. 209.165.200.230
    Secondary DHCP Server............................ Unconfigured
    DHCP Option 82................................... Disabled
    ACL.............................................. Unconfigured
    AP Manager....................................... Yes
    Guest Interface.................................. No
    Interface Name................................... service-port
    MAC Address...................................... c4:64:13:8f:93:41
    IP Address....................................... 192.168.1.157
    IP Netmask....................................... 255.255.255.0
    DHCP Option 82................................... Disabled
    DHCP Protocol.................................... Disabled
    AP Manager....................................... No
    Guest Interface.................................. No
    Interface Name................................... virtual
    MAC Address...................................... c4:64:13:8f:93:40
    IP Address....................................... 1.1.1.1
    DHCP Option 82................................... Disabled
    Virtual DNS Host Name............................ Disabled
    AP Manager....................................... No
    Guest Interface.................................. No
    WLAN Configuration
    WLAN Identifier.................................. 1
    Profile Name..................................... HOSP3C
    Network Name (SSID).............................. HOSP3C
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
      NAC-State...................................... Disabled
      Quarantine VLAN................................ 0
    Number of Active Clients......................... 0
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    WLAN ACL......................................... unconfigured
    DHCP Server...................................... 209.165.200.230
    DHCP Address Assignment Required................. Enabled
    Quality of Service............................... Platinum (voice)
    Scan Defer Priority.............................. 5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    IPv6 Support..................................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... 802.11b and 802.11g only
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
       Authentication................................ Disabled
       Accounting.................................... Disabled
       Dynamic Interface............................. Disabled
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Enabled
             AES Cipher.............................. Enabled
          Auth Key Management
             802.1x.................................. Disabled
             PSK..................................... Enabled
             CCKM.................................... Disabled
             FT(802.11r)............................. Disabled
             FT-PSK(802.11r)......................... Disabled
    FT Reassociation Timeout......................... 20
    FT Over-The-Air mode............................. Enabled
    FT Over-The-Ds mode.............................. Enabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       H-REAP Local Switching........................ Disabled
       H-REAP Learn IP Address....................... Enabled
       Infrastructure MFP protection................. Enabled
       Client MFP.................................... Optional
       Tkip MIC Countermeasure Hold-down Timer....... 60
    Call Snooping.................................... Disabled
    Band Select...................................... Enabled
    Load Balancing................................... Enabled
    Mobility Anchor List
    WLAN ID     IP Address            Status
    Press Enter to continue or to abort
    Press Enter to continue or to abort
    ACL Configuration
    Press Enter to continue or to abort
    CPU ACL Configuration
    CPU Acl Name................................ NOT CONFIGURED
    Wireless Traffic............................ Disabled
    Wired Traffic............................... Disabled
    RADIUS Configuration
    Vendor Id Backward Compatibility................. Disabled
    Call Station Id Case............................. lower
    Call Station Id Type............................. IP Address
    Aggressive Failover.............................. Enabled
    Keywrap.......................................... Disabled
    Fallback Test:
        Test Mode.................................... Off
        Probe User Name.............................. cisco-probe
        Interval (in seconds)........................ 300
    MAC Delimiter for Authentication Messages........ hyphen
    MAC Delimiter for Accounting Messages............ hyphen
    Authentication Servers
    Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/P
    hase1/Group/Lifetime/Auth/Encr
    Accounting Servers
    Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/P
    hase1/Group/Lifetime/Auth/Encr
    --More or (q)uit current module or to abort
    TACACS Configuration
    Authentication Servers
    Idx  Server Address    Port    State     Tout
    Authorization Servers
    Idx  Server Address    Port    State     Tout
    Accounting Servers
    Idx  Server Address    Port    State     Tout
    LDAP Configuration
    Press Enter to continue or to abort
    Local EAP Configuration
    User credentials database search order:
        Primary ..................................... Local DB
    Timer:
        Active timeout .............................. 300
    Configured EAP profiles:
    EAP Method configuration:
        EAP-FAST:
          Server key ................................
          TTL for the PAC ........................... 10
          Anonymous provision allowed ............... Yes
          Authority ID .............................. 436973636f00000000000000000000
    00
          Authority Information ..................... Cisco A-ID
    Press Enter to continue or to abort
    HREAP Group Summary
    HREAP Group Summary: Count: 0
    Group Name                # Aps
    Press Enter to continue or to abort
    HREAP Group Detail
    Press Enter to continue or to abort
    Route  Info
    Number of Routes................................. 0
    Destination Network          Netmask               Gateway
    Press Enter to continue or to abort
    Qos Queue Length Info
    Platinum queue length............................ 100
    Gold queue length................................  75
    Silver queue length..............................  50
    Bronze queue length..............................  25
    Press Enter to continue or to abort
    Mac Filter Info
    Press Enter to continue or to abort
    Authorization List
    Authorize MIC APs against AAA ................... disabled
    Authorize LSC APs against Auth-List ............. disabled
    Allow APs with MIC - Manufactured Installed C.... disabled
    Allow APs with SSC - Self-Signed Certificate..... disabled
    Allow APs with LSC - Locally Significant Cert.... disabled
    Load Balancing Info
    Aggressive Load Balancing........................ Disabled
    Aggressive Load Balancing Window................. 5 clients
    Aggressive Load Balancing Denial Count........... 3
    Statistics
    Total Denied Count............................... 0 clients
    Total Denial Sent................................ 0 messages
    Exceeded Denial Max Limit Count.................. 0 times
    None 5G Candidate Count.......................... 0 times
    None 2.4G Candidate Count........................ 0 times
    Press Enter to continue or to abort
    Dhcp Scope Info
    Scope: PUNTOSAP
    Enabled.......................................... Yes
    Lease Time....................................... 86400 (1 day )
    Pool Start....................................... 209.165.200.201
    Pool End......................................... 209.165.200.229
    Network.......................................... 209.165.200.0
    Netmask.......................................... 255.255.255.0
    Default Routers.................................. 0.0.0.0  0.0.0.0  0.0.0.0
    DNS Domain.......................................
    DNS.............................................. 0.0.0.0  0.0.0.0  0.0.0.0
    Netbios Name Servers............................. 0.0.0.0  0.0.0.0  0.0.0.0
    Press Enter to continue or to abort
    Exclusion List ConfigurationUnable to retrieve exclusion-list entry
    Press Enter to continue or to abort
    CDP Configuration
    Press Enter to continue or to abort
    Country Channels Configuration
    Configured Country............................. ES  - Spain
          KEY: * = Channel is legal in this country and may be configured manually.
               A = Channel is the Auto-RF default in this country.
               . = Channel is not legal in this country.
               C = Channel has been configured for use by Auto-RF.
               x = Channel is available to be configured for use by Auto-RF.
             (-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
    -----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
        802.11bg     :
        Channels     :                   1 1 1 1 1
                     : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
    -----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    ES (-E   ,-E   ): A * * * * A * * * * A * * .
    -----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
        802.11a      :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
        Channels     : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
                     : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
    -----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    ES (-E   ,-E   ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
    Press Enter to continue or to abort
    WPS Configuration Summary
    Auto-Immune
      Auto-Immune.................................... Disabled
    Client Exclusion Policy
      Excessive 802.11-association failures.......... Enabled
      Excessive 802.11-authentication failures....... Enabled
      Excessive 802.1x-authentication................ Enabled
      IP-theft....................................... Enabled
      Excessive Web authentication failure........... Enabled
    Signature Policy
      Signature Processing........................... Enabled
    Press Enter to continue or to abort
    Custom Web Configuration
    Radius Authentication Method..................... PAP
    Cisco Logo....................................... Enabled
    CustomLogo....................................... None
    Custom Title..................................... None
    Custom Message................................... None
    Custom Redirect URL.............................. None
    Web Authentication Type.......................... Internal Default
    External Web Authentication URL.................. None
    Configuration Per Profile:
    Rogue AP Configuration
    Rogue Location Discovery Protocol................ Disabled
    Rogue on wire Auto-Contain....................... Disabled
    Rogue using our SSID Auto-Contain................ Disabled
    Valid client on rogue AP Auto-Contain............ Disabled
    Rogue AP timeout................................. 1200
    MAC Address        Classification     # APs # Clients Last Heard
    Adhoc Rogue Configuration
    Detect and report Ad-Hoc Networks................ Enabled
    Auto-Contain Ad-Hoc Networks..................... Disabled
    Client MAC Address  Adhoc BSSID         State              # APs   Last Heard
    Rogue Client Configuration
    Validate rogue clients against AAA............... Disabled
    Rogue Client Configuration
    Validate rogue clients against AAA............... Disabled
    --More-- or (q)uit
    MAC Address        State              # APs Last Heard
    Ignore List Configuration
    MAC Address
    Rogue Rule Configuration
    Priority Rule Name               State    Type          Match Hit Count
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 6.0.199.4
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console
    1.27
    Build Type....................................... DATA + WPS
    System Name...................................... CISCO-CAPWAP-CONTROLLER
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 209.165.200.230
    Last Reset....................................... Power on reset
    System Up Time................................... 0 days 0 hrs 41 mins 2 secs
    System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
    Rome, Vienna
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... ES  - Spain
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +39 C
    External Temperature............................. +23 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Disabled
    Number of WLANs.................................. 1
    3rd Party Access Point Support................... Disabled
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ C4:64:13:8F:93:40
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 25
    (Cisco Controller) >
    The AP log
    AP442b.03dc.0925>
    *Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
    '(index 0).
    *Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    logging facility kern
            ^
    % Invalid input detected at '^' marker.
    logging facility kern
            ^
    % Invalid input detected at '^' marker.
    *Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
    p: 209.165.200.230 peer_port: 5246
    *Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
    peer_ip: 209.165.200.230 peer_port: 5246
    *Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
    0
    *Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
    version 6.0.199.4  ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
    *Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
    .165.200.230:5246
    *Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
    not established

  • Wireless Controller 5508 dropping MAC Addresses

    Our 5508 Wireless Controller will drop MAC addresses clean out of the system. Addresses that are in use everyday just disappear. It is not a limitation issue because we are adding iPads everyday. And it is not a daily occurance, but maybe once or twice a week. Has anyone come accross this issue? Everything has been updated and it is more of a hassle than anything, I am just trying to understand what is happening.

    Shannon,
         can you be a bit more specific, when you say it's dropping mac addresses?
    is that from the user list? the macfilter?

  • Save config of Wireless Controller 5508 by SNMP

    On Catalyst switches one can save the running config with SNMP by using the CISCO-CONFIG-COPY-MIB.
    Is there an equivalent way of doing this on a 5508 Wireless Controller ?
    Many thanks
    chris

    Is it Cisco best practices to create one large Vlan that contains both controllers, ap's and clients all in the same network ? Or should I be segmenting the network a particular way?
         Not best practice.  Segmentation is up to how you want to do it for the most part
    With my current Wireless Controllers is it possible to segment the wireless network by building into seperate networks (vlans) but still allow clients to connect to the (mmg_wireless) ssid and roam throughout the campus without mobility and roaming issues?
         yes, you could use AP groups and do a subnet per building.  the traffic will still backhaul to the WLC then to the core.  So if the latency is the fiber between the buildings you would still have an issue.  you could also use FlexConnect, but would need to know more on how the application is supposed to work to answer that better
    Is it necessary to segment my wireless network by creating more vlans instead of putting all of the ap's controllers and clients all in the same network? Will having all of my wireless devices in the same subnet degrade my wireless network because everything is in the same broadcast domain?
         IMHO, I think the AP should be in their own VLAN, and the WLC can live in the 'server' vlan if you want.
    Is there a maximum recommended number of ap's that should be on a controller at any given moment? I currently have 200 ap's on one controller.
    with 672 clients currently conencted to them. (360 of them are connected to the mmg_wireless ssid) .
         how many ports are you using to connect to teh 6509?  if you are using all 8 ports you should be fine.
    Is it best practice to seperate the maangement ip's of the controllers and ap's from the client vlans?
              answered above

  • Statistics\Reporting from a Wireless Conrtoller

    After explaining all of our requirenments to the local Cisco Partner they prepared a quote and we purchased a Cisco 5508 Wireless Controller and 6 Aironet 1141 wireless access points.  The wireless coverage in the building is great.
    The problem is, we paid over $10,000 and one of the big reasons we upgraded is that I really need to get statistics.  How many devices are using the wireless over a period of time.  I need to be able to report how many and what type of user are accessing our wireless on a monthly basis.
    I cannot find a way to do it from the software on the Wireless Controller and now theCisco partner has no clue how to get that information for us either.
    Has anyone else found a way to do this?
    Thanks,
    Anna

    Hi Anna,
    We can use Either Cisco WCS or NCS for this or u can go for any freeware SNMP walk tool on Google and use WLC MIBS on the same.. however... these can answer only the first part of ur question that is..how many and what type of user are accessing our wireless on a monthly basis.
    But i am not sure of any device on this earth telling us what type of device users are accessing.. may be this will give u the MAC address and then using OUI i thing u need to get the vendor information..
    Please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • Wireless disconnect after login with Remote desktop with wpa2

    We have 5508 wireless controller with 1142 aironet acess points.... we configured Radius authentication on ACS 5.3  for wireless users
    when we take remote desktop connection of wireless client ... it disconnects after 10 sec.
    and  when we logged in to client ... connectivity was lossed  .. I have to reconnect Manually  to client..
    It's really frustrating for all our service engineers to work remotly ....... Please Help

    Hi Santosh,
    which vesrion of sw u r running on WLC ?
    Open Caveats on 7.4.100.0, CSCuc78713 could be related to this;
    CSCuc78713
    Symptom: Wireless client cannot receive broadcast packets after broadcast key rotation.
    Conditions: Dynamic WEP; 7.0.235.0, 7.2.110.0, and 7.3.101.0 controller software releases.
    Workaround:
    • Executes the config advanced eap bcast-key-interval 86400 in the middle of the night
    • Change security setting to WPA2, and so on.
    Regards

Maybe you are looking for

  • Customer fields do not display in Define Field Groups for Cust. Fields IMG

    I am customizing to display cusotmer fields in cporjects IMG actviity 'Define Field Groups for Customer Fields'. I am able to see the main tab in object category and multiple sub tabs in it. However customer fields that have been added by Enhance dat

  • HT1040 Previewing a book in Aperture

    In previewing my book as a PDF in Aperture, the wrap-around dust jack displays the title of the book just fine.  However, the hardcover book does not display the title correctly.  It only shows the top of the letters in the title.  Is there a font si

  • Website in hindi, gujrati, urdu, marathi

    i have created a web site in english i want my web site to be in some of the local languages like hindi, gujrati, urdu, marathi can any one help me how to display those characters in browser

  • LR and Adorama - whats your workflow?

    hey folks, now that i have my web export solution taken care of, im curious about printing. ive used adorama a few times and am happy w/ the results. anyone feel like sharing -- how do you prep your images for use w/ them? what settings have been suc

  • After I ran factory recovery manager I ran into Command screen .. Now what?-

    after I ran factory recovery manager for my HP Compaq Presario CQ60 220us everything was moving right along and I must have blinked because now I'm looking at this black command prompt screen  with a cursor flashing waiting for me type write a comman