5510 not passing diagnostics of reboot

I recently have relocated. Upon power up of 5510 printer it turns on then displays HP with the bar, after this it quickly displays c8190210 and then all buttons start flashing and that is it.

Hello wjscott,
Please perform the below listed steps....
While the printer is ON, unplug the power cord from back of the printer and the Power source.
Also unplug any cables connecetd to the printer.
Power Off the Wireless Router if you have any ?
Wait for 30 seconds.
Plug in the printer power cable directly to Wall Outlet and then to the printer.
If printer does not power ON, then press the ON button.
The printer should recover from the error. If not You may have to call HP for Further Support.
If the printer recovers from the Error, then Power on the Router.
If issue still persists, then please call HP Tech Support for further assistance.
If you are in US , the toll free # is 1-800-474-6836 .
If you are not in US , then log on to www.hp.com , at bottom-left corner there is a world map icon, click on it and then select the region you belong to, which would then provide support options for you for that region.
Regards,
Jabzi
Give Kudos to say "thanks" by clicking on the "thumps Up icon" .
Click "Accept as Solution" if it solved your problem, so others can find it.
Although I am an HP employee, I am speaking for myself and not for HP.

Similar Messages

1424 does not pass diagnostics after running program

Hello, we are using the PCI-1424 card with a Dalsa linescan camera, and are having trouble trying to do ring acquisitions with different buffer sizes. The camera either times out or always returns the number of lines that it is first set to, ie; if the original number of lines is 100, and the number of lines is then set to 1000 (and confirmed using imgGetAttribute(DisplaySid, IMG_ATTR_ACQWINDOW_HEIGHT, &nBufSize).
I've noticed that the 1424 board does not pass 2 of the diagnostic tests in MAX. The details it returns are:
Advanced Control Circuitry failed
Configuration could not be written to when Confwren bit was set. [F1.5]
Timing Circuitry failed
Counter configuration could not be loaded. [T1.0
Is this a programming error on my part? I am closing the session and the interface, which in my opinion should be all that is needed to reset the board to the default settings. This does not work, even the snap acquisition in MAX fails.

I'm not surprised at the behavior that you are seeing. When the acquisition is started the board is programmed with the acquisition size and when you change that it has to reprogram the board while it is acquiring, so either it will timeout or it just won't do it and you will only see the first size. I'm not sure why the diagnostics are failing but it sounds like you can reboot and that resolves the issue. I would recommend looking into a couple of alternatives. Variable Height Acquistion uses a hardware signal to indicate how many lines should be in an image. If you didn't have a signal you could generate one with a DAQ card or you could programmatically assert
and deassert one of the trigger lines on the 1424 but that would not be the most accurate depending on your line rate. The other alternative would be to set the image size to the largest size and then just crop the images.
Regards,
JR A.
Application Engineer
National Instruments

Changes to selected columns to display in Details tab in Task Manager are not saved during a reboot

I use Task Manager on Server 2008 R2 to monitor performance. I have added several columns to the Processes tab using View..Select Columns. I have added CPU time, I/O read/write/other bytes, etc.
The equivalent in Server 2012 is the Details tab. I figured out how to add these same columns - right click on the column headers, and choose "Select columns". This is not obvious by the way.
However these selections are not persistent across a reboot. So every time I reboot, I need to add the columns back to the display. That is not the case with Server 2008 R2 - they are persistent.
I am using a domain administrator userid, but not using roaming profiles.
This is a retrogression vs. Server 2008 R2. Can it be fixed?

Hi,
I meant that both the added columns of Windows Server 2008 R2 and Windows Serve r2012 RC are persistent.
You may install a new Windows Serve r2012 RC to check the symptom.
Currently, you may perform a System File Checker (SFC /Scannow) to check the result.
Regards,
Arthur Li
TechNet Community Support
Arthur, I have the exact same problem as David Trounce. The problem exists, as he described it, and I don't think you are understanding it. Please pass this problem/bug/defect report to someone else so that it can be logged and fixed before
RTM. Thanks! -Kent

Did not pass integrity check??? Help

I am using internet explorer 8, on a brand new Toshiba Laptop, on wireless broadband but yet when I try downloading Adobe Flash Player 10, it is taking approximatly 2 hours on the download window with the green bar to get to 100% and when it does get to 100% it is saying that it did not pass the integrity check and if I click resume it starts the download all over again.
I have tried using different browsers ie Mozilla Firefox and Opera and it is still the same...
I have a support case open with Adobe for this but so far anything they have told me I have been unsucessful with.
Please Help!!.........
kind regards

Hello, What OS are you using? Are you trying to install the latest Flash Player vs 10.0.42.34? Have you run the uninstaller
from here? http://kb2.adobe.com/cps/141/tn_14157.html You may want to read each section to be sure to comply with the various requirements before running it. Especially the last part if you are using IE. This is downloaded to your desktop. Close all browsers and check the system tray; nothing that uses Flash should be running.
After running the Uninstaller, it is a good idea to go to Tools>Internet Options and check both sections of the add ons to
check if the old Shockwave Flash Object version ActiveX Control has been removed. If it has not, run the Uninstaller again. Then be sure to Reboot again.
Before running the offline Installer, I would suggest you read the troubleshooting link. It may help to be familiar with the various issues that an install might fail before trying it again.
http://go.adobe.com/kb/ts_tn_19166_en-us This is the troubleshooting link
http://fpdownload.macromedia.com/get/flashplayer/current/install_flash_player_ax.exe Installer link for IE-Download to the desktop.
After installing, go here to the Adobe test site: http://www.adobe.com/products/flash/about
If you have any questions before or after, please post.
Thank you

I can not pass the language settings menu

Hello,
Since I have tried to get the latest build of Apple TV, my apple TV can not pass the language settings menu. I choose my language and then it loops back to language settings menu.
I have restored twice from iTunes, plug and unplug from the tv, the electric network, and so on, but it does the same loop.
Anybody has solved this problem ?
Regards,
F

If you can't get past the lock screen when you slide to unlock, try rebooting your iPad and then try again.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

I can not pass the lock screen

I can not pass the lock screen, when I slide to unlock

If you can't get past the lock screen when you slide to unlock, try rebooting your iPad and then try again.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

GRE traffic can not pass through LRT224 IPSec Tunnel

Hi,
We have a trouble when using Cisco Router GRE tunnel plus LRT224 IPSec Gateway-Gateway Tunnel.
We found after reboot, GRE packets can not pass trough LRT224 IPSec tunnel. need to restart serval time then gre will back to normal.
Besides that, GRE keepalive packets can not pass trough LRT224 IPSec Tunnel.
please help. I had tried to upgrade to latest firmware version.
Firmware Version : v1.0.3.09 (Dec 26 2014 14:28:46)
A-END:
interface Tunnel1
ip address 10.216.80.105 255.255.255.252
ip mtu 1400
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1360
ip ospf network point-to-point
ip ospf hello-interval 3
ip ospf cost 10000
tunnel source 10.216.81.2
tunnel destination 10.216.80.90
end
B-END:
interface Tunnel11
ip address 10.216.80.110 255.255.255.252
ip mtu 1400
ip tcp adjust-mss 1360
ip ospf network point-to-point
ip ospf cost 10000
ip ospf hello-interval 3
tunnel source 10.216.80.91
tunnel destination 10.216.81.3
end
CISCO2911 <> LRT224 <> INTERNET <> LRT224 <> CISCO 2621
San

Can you post the results from the below command for the Cisco Routers?
IOS Command: "sh version"
Why not static route without NAT through the LRT224 IPSec VPN?
Just curious why did you use LRT224's for the Site to Site VPN instead of the Cisco Routers?
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

"Reply" to email not passing email address

Have been experiencing an issue with Thunderbird (31.2.0) where any time I click REPLY button the address for the sender of original email is not passed to new email. I have to copy the sender's address and paste it into the new email.
This has been happening for the past 3 days. Tried shutting down application and rebooting several times, but no change.

Bit of a long shot, but try restarting the operating system in '''[http://en.wikipedia.org/wiki/Safe_mode safe mode with Networking]'''. This loads only the very basics needed to start your computer while enabling an Internet connection. Click on your operating system for instructions on how to start in safe mode: [http://windows.microsoft.com/en-us/windows-8/windows-startup-settings-including-safe-mode Windows 8], [http://windows.microsoft.com/en-us/windows/start-computer-safe-mode#start-computer-safe-mode=windows-7 Windows 7], [http://windows.microsoft.com/en-us/windows/start-computer-safe-mode#start-computer-safe-mode=windows-vista Windows Vista], [http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/boot_failsafe.mspx?mfr=true" Windows XP], [http://support.apple.com/kb/ht1564 OSX]

Iphone 4 front camera not working even after reboot,resets and restore.

i am using iphone 4 .I have problem that front camera is not working even after reboot,resets and restore with itunes.I thing there is a hardware problem.
Now i wont to go apple store for replace the phone because phone is under warranty period.But problem is that i lost the receipt.Will apple store help me without my receipt ?please help me

If setting up as new device without using the latest backup does not bring the camera function back, get it looked at or serviced by Apple:
How to back up your data and set up as a new device
Apple - Support - Service Answer Center

Captivate 6 Text Entry Events Do Not Pass

I am a long-time user of Captivate going back to version 2. I've created a simulation course with numerous text entry events that do not validate correctly. I am typically using the TAB key to validate the text entered. I have several lessons where everything works fine, but many that have problems.
Typically when TAB is used at the end of a key press, you will see focus shift to the first button on the Play bar - and this does not cause any problems. I see this behavior on the events in my course that work. However, for the ones that do not work, I see the focus shifting to the Address Bar and the event will not pass.
The only workaround I have employed is to use On Focus Lost: Go to Next. This is not a great solution because the text no longer validates with this setting. These events will pass no matter what is entered.
I would really appreciate your help with this! My course is due soon. I would be happy to provide more information or upload my file for your inspection. Thank you!

For anyone who might be experiencing the same problem and looking for an answer - this is still 100% broken in Captivate version 6. None of the fixes discussed in the above referenced thread work. I tried playbar widgets, editing the playbars in Flash. No luck.
Adobe just moves forward from version to version not fixing the bugs they create in prior versions. That's your incentive to upgrade, folks.
Best workaround I can offer is Use ENTER as your validation keystroke. It doesn't have the same problems associated with TAB. Good luck!

Updated my iphone4 with ios6.1 software. App store is not working. Tried rebooting, restoring, changing date, signing with another apple id etc. but no luck. can someone please help?

Updated my iphone4 with ios6.1 software. App store is not working. Tried rebooting, restoring, changing date, signing with another apple id etc. but no luck. can someone please help?

I guess I will wrap this up. I have abandoned iPhoto and viewing my Photo Streams using it and moved to Adobe products (Bridge + PS). So that's that.

Firefox works fine until after lunch. Then it will not open, unless I reboot. Am at work, & I shouldnt have to do that, NEED a fix.

Everyday its the same thing. By midafternoon, Firefox will not open unless I reboot. I am at work, and have too many things open all day to stop and reboot for a browser, when I also have IE. I prefer Firefox, it is set as my default, and have many passwords saved there that are not saved in IE. Surely there is a fix for this? I have removed it, downloaded it again, followed other suggestions from your site, but still have the same problem. If I leave a window open all day long, it will still work for me, and thats what I try to do. However, invariably, there will come that accidental second that I hit the red X at the top and totally regret it! Please help!

I had tried this before, but went ahead and tried this again.
I clicked on "reset Firefox". Firefox closed, but did not come back up. When I tried to open it again, I did receive a message that said Firefox is running but is not responding, that I couldn't open another window without stopping the processes on the other page.
I never got a window that showed me the information that was imported, or a place to click finish.
Since I don't believe this completed, I don't believe my problem will be solved.
Debra

Scheduling Agreement -Schedule line should not pass the requirement to MRP

Hi Friends!
As we all know the scheduling agreements is outline agreement with future schedule lines, with this system will pass the requirements to MRP for the schedule line which is even after 5 years, so my requirement is if the schedule line date is above 15 days from the current date then requirement should not pass to MRP.
solution which we gave is, SA initially will determine the schedule line category as CN (which will not transfer the requirement) and a batch job program will run daily and it will check for each schedule line if any of the schedule is with in the 15 days from the current date then it will change the schedule line category from CN to CP.
Now the problem is , by using Batch Job which program I have to call to change the schedule line category?????
1. we tried BAPI_SALESORDER_CHANGE but when we are changing the CN to CP it is not performing ATP where as if we do manually it is performing.
2. we tried BDC but here also we facing some strange problem i.e. while recording the ATP screen is not populating where it is coming while doing manual.
Can someone let me know which one program we should call in Batch job to do this change.
Regards
Nath

Hi nath,
i also failed in changing shedule line category in userexit and in BAPI.
in one case, i succeded in doing it with a bdc after MV45AFZZ / userexit_save just bevore the datas are reset but after the commit-work is processed.
the other possibility is, to change the accepted amount in userexit RV03VFZZ / USEREXIT_AVAILABILITY_OUT.
3. possibility is, to block the order with a delivery - block , same as the credit-control-block. This block can be set in MV45AFZZ or perhaps in BAPI too.
hans

Dashboard prompt value is not passing into the report

Hi,
I am using OBIEE 10g. The problem is in Oracle BI Answers
I have a prompt and its related report. In the prompt, in one of the column, I am using sql result. The sql query is a co-related sub query where i have used 2 tables. employee_data and employee_region. The reason for using sub-query is that there is no data_center column in the employee_data table. It has the records for all the data_center e.g USA, UK,IND,AUSTRALIA etc So, I used the sub query with condition which will give the result on a particular data center (here it is USA) and this sub query's output is input for the main query. And the prompts works fine and gives correct result
The sql query used for the column in the prompt (in Oracle BI Answers) as
SELECT EMPLOYEE_DATA.ENAME FROM EMPLOYEE WHERE EMPLOYEE_DATA.ENAME IN (SELECT EMPLOYEE_REGION.ENAME FROM EMPLOYEE WHERE EMPLOYEE_REGION.DATA_CENTER = 'USA')Now in the report, there are 2 coulmns. - EMPLOYEE_DATA.ENAME and EMPLOYEE_REGION.DATA_CENTER
I have used the main column EMPLOYEE_DATA.ENAME for filter as 'prompted'.
The problem is the value from the prompt is not passing from the prompt to the report, what I found. Because, instead of showing the result for 'USA' data_center, It also shows other data_center 's (UK,IND,AUSTRALIA) data.
How filter condition I should use for EMPLOYEE_DATA.ENAME column in the report so that the prompt value will pass to the report properly ?
Thanks
Edited by: Kuldip on Feb 21, 2013 6:17 AM

Hi Kuldip,
There are 2 ways of doing it.
1. Nice and good: For the section where the report is put have a condition to display only if it returns rows. For details please refer to :
http://bischool.wordpress.com/category/guided-navigation/
2. The easy way: Add a "No Result" view to your report and add few spaces in the text.
Let me know if this helped.
Regards,
Jay

Filters 'OR' function not passing the values to the sql

Hi,
I am facing an issue with the 'OR' function on the filters that are used in the reports.
The report needs to fetch all the records on the three tables as the user enters the value in the dashboard prompts.
eg: [   update_dt_A1 is prompted
and user_name_A1 is prompted ]
or
[    update_dt_B1 is prompted
and user_name_B1 is prompted ]
or
[    update_dt_C1 is prompted
and user_name_C1 is prompted ]
The values entered in the dashboard prompt gets passed to the filter, but the vaules are not passed over to the SQL that runs on the database, hence the reports shows all values and does not reflect the values entered.
When the 'OR' function is replaced with 'AND' the values get passed to the SQL.
Can anyone help on what is the issue on the filters?
Thanks

Here is how my Filters are set up
Vendor Name is Prompted
AND
Vendor Number is Prompted
AND
[   [Last_update_date_Vendor is prompted
AND
User_name_Vendor is prompted]
OR
[Last_update_date_Site is prompted
    AND
    User_name_Site is prompted]
OR
[Last_update_date_Bank is prompted
    AND
    User_name_Bank is prompted]
The values from the dashboard prompts gets passed to the filter, but the sql that runs does not take the values in the where clause.

5510 not passing diagnostics of reboot

Similar Messages

Maybe you are looking for