5530 (probably) temperature problem

I have 5530 an year and a few months already. Approximately at second month it began rebooting automatically . Firstly thought that it's some software problem. ( Now I'm not sure is it really)So I found that it reboots only when device temperature decreases (for example - if I put it out from my pocket and air temperature is below 20 centigrade). And when display is locked it even turns off and won't turn on (only vibrates twice) till it's not warmed up again.
I did all upgrades since fw version 10.0.050 problem persists. My question is what kind of problem may it be ? Some software problem , battery problem or temperature sensor problem? (if it's software problem how can I solve it alone because the place I bought phone is really far for me).

It's hard for us to know what's causing this, but it's likley to believe it's hard ware related.
But first, did you do anything special to the device before it started to happen?
Have you installed a new memory card?
Installed new 3rd party apps?
Swapped Sim card?
But if you're sure that it behaves like this dependant on temp, I would take it to a Nokia care point for an inspection and possibly repair.
You can find your nearest care point here: http://europe.nokia.com/support/repair-and-recycle/repair/care-points

Similar Messages

MacbookPro 13'' temperature problem

Hi everyone, I have a Macbook Pro 13'' Mid-2012 (A1278) with a Intel Core i7 2.9GHz for a year ago, but the cpu fan is a little noisy and I check temperature with a "Temperature Monitor App" and CPU Temp is 80ºC with only Chrome and Coda 2 opened.
Normally I work on 3D applications like Autodesk Maya and AutoCAD, this apps can overheat the cpu but now i can't work with these apps because the performance is very low, I cleaned up the logic board and temperature don't decrease.
¿How can I decrease CPU Temp? I bought a new CPU Fan and I don't want it damage again...
Thanks for help me and sorry for my english I speak spanish

Nahomi López wrote:
And the magsafe connector is so hot like 100ºC but charge the battery and works fine but is hot. I have 2 chargers one 65W (original) and another 95W from another macbook and both have the same temperature problem.
100°c on the charger body is unacceptable and would be impossible to touch for more than a second. Mine have never been more than 55°c. There is something terribly wrong here. Look at the contacts between the charger and the MBP. Is there any discoloration? the pins in the charger connection are spring loaded, do they move easily?
Fan Speed is 6140 rpm and CPU temp is 75ºC, I think a change the thermal compound.
The CPU temperature is not bad nor is the fan speed. I have doubts about that replacing the thermal paste will improve thew situation.
Open the MBP and see if there is dust an debris inside. I f so clean it out.
Again, delete Google Chrome and see what happens. It has been known to have compatibility problems with OSX.
Ciao.

[SOLVED] Notebook temperature problem

Hi everyone,
I use Arch Linux (i686) since 2008 on different machines. But my Acer 8935G Notebook is giving me headaches for some time now.
I bought it one year ago and Arch Linux ran nearly out of the box (ALSA drivers took some time, but that's done). In spring I noticed, that the computer is getting hotter than it did before (Idle: 70° Celsius / 158° Fahrenheit). In Windows Vista, I get idle temperatures around 40° C (104° F). And before spring, I got temps booting Linux around 50° C (122° F), which was absolutley okay and worked for me.
I didn't change system settings or configurations, and I tried some possible solutions, because I thought, maybe it's a kernel problem, but that's just a wild guess.
What I did so far:
- trying alternate kernels (BFS, CK, ZEN)
- tried different cpufreq settings (dynamic cpu scaling is working -> cpufreq-info)
- undervolting via intel-phc (no changes in temperature at all)
- tried powertop
none of that worked.
I have to say, that's not just a Arch Linux-related problem, other distributions give me the same problems (PCLinuxOS 2010, Linux Mint KDE 4.4).
My question so far is - has anybody experienced similar problems and found a solution for it?
Thanks in advance for the help - I'll really appreciate it.
PowerTOP 1.13 (C) 2007 - 2010 Intel Corporation
Sammle Daten für 30 Sekunden
Ihre CPU unterstützt folgende C-Status:C1 C2 C3 C4 C5 C6
Ihr BIOS meldet folgende C-Status:C1 C2 C6
Cn Verweildauer
C0 (Prozessor läuft) ( 5,0%)
zyklisches AbfraC1 mwait 3,0ms ( 0,0%)
C1 mwait 0,5ms ( 0,0%)
C2 mwait 2,6ms (20,9%)
C6 mwait 4,4ms (74,0%)
P-States (Frequenzen)
Turbo-Modus 3,2%
2,67 GHz 0,2%
2,14 GHz 0,3%
1,60 GHz 1,2%
800 MHz 95,1%
Aufwachen pro Sekunde : 248,2 Intervall: 30,0s
Keine ACPI Stromverbrauch-Schätzung verfügbar
Häufigste Ursachen für das Aufwachen:
31,8% ( 88,3) [kernel scheduler] Load balancing tick
28,4% ( 79,0) PS/2 keyboard/mouse/touchpad interrupt
8,7% ( 24,1) [iwlagn] <interrupt>
8,4% ( 23,4) [extra timer interrupt]
3,9% ( 10,9) [Rescheduling interrupts] <kernel IPI>
3,3% ( 9,0) plasma-desktop
2,6% ( 7,2) [kernel core] hrtimer_start (tick_sched_timer)
2,3% ( 6,5) chromium
1,4% ( 4,0) [kernel core] usb_hcd_poll_rh_status (rh_timer_func)
1,4% ( 3,8) X
1,3% ( 3,7) [TLB shootdowns] <kernel IPI>
1,2% ( 3,2) knotify4
0,9% ( 2,5) [acpi] <interrupt>
0,8% ( 2,2) mysqld
0,5% ( 1,5) [i915] <interrupt>
0,4% ( 1,2) [ahci] <interrupt>
0,4% ( 1,1) kwin
0,4% ( 1,0) knemo
0,3% ( 1,0) [kernel core] iwl_bg_monitor_recover (iwl_bg_monitor_recover)
0,2% ( 0,5) virtuoso-t
0,2% ( 0,5) hald-addon-stor
0,2% ( 0,5) [kernel core] __enqueue_rt_entity (sched_rt_period_timer)
0,1% ( 0,3) gpg-agent
0,1% ( 0,3) [Function call interrupts] <kernel IPI>
0,1% ( 0,2) kslowd000
0,1% ( 0,2) kded4
0,1% ( 0,2) init
0,1% ( 0,2) akonadiserver
0,1% ( 0,2) flush-8:16
0,1% ( 0,2) flush-8:0
0,1% ( 0,2) bdi-default
0,0% ( 0,1) konsole
0,0% ( 0,1) nepomukservices
0,0% ( 0,1) [kernel core] bdi_arm_supers_timer (sync_supers_timer_fn)
0,0% ( 0,1) akonadi_control
0,0% ( 0,1) kslowd001
0,0% ( 0,1) crond
0,0% ( 0,1) sensors
0,0% ( 0,0) [kernel core] cfq_completed_request (cfq_idle_slice_timer)
0,0% ( 0,0) hald
0,0% ( 0,0) [kernel core] neigh_timer_handler (neigh_timer_handler)
0,0% ( 0,0) [kernel core] neigh_add_timer (neigh_timer_handler)
0,0% ( 0,0) [kernel core] sk_reset_timer (tcp_delack_timer)
0,0% ( 0,0) rpcbind
An audio device is active 100,0% of the time:
hwC0D0 Realtek ALC889
Ein USB Gerät ist 100,0% der Zeit aktiv:
USB Gerät 1-2 : FingerPrinter Reader (Generic)
Suggestion: Enable Device Power Management by pressing the P key
Vorschlag: Aktivieren Sie USB-Autosuspend für Nicht-Eingabegeräte inden Sie die U-Taste betätigen
Vorschlag: Erhöhen Sie die "VM dirty writeback time" von 5,00 auf
15 Sekunden durch: echo 1500 > /proc/sys/vm/dirty_writeback_centisecs
Dadurch belasten die VM Hintergrundaktivitäten die Festplatte weniger.
Deaktivieren Sie mit folgendem Befehl die "Wake-On-Lan" Funktion:
ethtool -s eth0 wol d
"Wake-On-Lan" hält die Physikalische Netzwerkverbindung aufrecht.
Vorschlag: Aktivieren Sie das SATA ALPM link power Management mit: echo min_power > /sys/class/scsi_host/host0/link_power_management_policy
oder durch betätigen der S-Taste.
Vorschlag: Aktivieren Sie mit folgendem Befehl die WLAN Stromsparfunktionen:
iwconfig wlan0 power timeout 500ms
Dadurch verringert sich die WLAN-Geschwindigkeit etwas, spart aber Strom.
Vorschlag: Aktivieren Sie mit folgendem Befehl die HD-Audio Stromsparfunktionen:
echo 1 > /sys/module/snd_hda_intel/parameters/power_save
oder übergeben Sie dem Modul den Parameter power_save=1.
Suggestion: Enable the CONFIG_PCIEASPM kernel configuration option.
PCI Link Powermanagement (ASPM) allows the hardware to go to low power mode
automatically when a PCI-E device is idle.
aktuelle "USB suspend" Statistiken
Name des aktiven Gerätes
100,0% USB Gerät 3-1 : BCM2046 Bluetooth Device (Broadcom Corp)
100,0% USB Gerät 2-7 : HD Video WebCam (SuYin)
100,0% USB Gerät 2-6 : A309 (AVerMedia)
100,0% USB Gerät 1-2 : FingerPrinter Reader (Generic)
0,0% USB Gerät usb8 : UHCI Host Controller (Linux 2.6.35-ARCH uhci_hcd)
0,0% USB Gerät usb7 : UHCI Host Controller (Linux 2.6.35-ARCH uhci_hcd)
0,0% USB Gerät usb6 : UHCI Host Controller (Linux 2.6.35-ARCH uhci_hcd)
0,0% USB Gerät usb5 : UHCI Host Controller (Linux 2.6.35-ARCH uhci_hcd)
0,0% USB Gerät usb4 : UHCI Host Controller (Linux 2.6.35-ARCH uhci_hcd)
100,0% USB Gerät usb3 : UHCI Host Controller (Linux 2.6.35-ARCH uhci_hcd)
100,0% USB Gerät usb2 : EHCI Host Controller (Linux 2.6.35-ARCH ehci_hcd)
100,0% USB Gerät usb1 : EHCI Host Controller (Linux 2.6.35-ARCH ehci_hcd)
Runtime Device Power Management statistics
Name des aktiven Gerätes
Devices without runtime PM
09:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
06:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe
02:00.2 Mass storage controller: O2 Micro, Inc. Device 8130
02:00.1 SD Host controller: O2 Micro, Inc. Device 8120
02:00.0 FireWire (IEEE 1394): O2 Micro, Inc. Device 10f7
01:00.1 Audio device: ATI Technologies Inc RV710/730
01:00.0 VGA compatible controller: ATI Technologies Inc Device 9488
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller
00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge
16 more devices without runtime PM ommitted
Recent audio activity statistics
Name des aktiven Gerätes
100,0% hwC0D0 Realtek ALC889
Recent SATA AHCI link activity statistics
Active Partial Slumber Device name
Last edited by ewigkeit (2010-09-27 16:31:13)

Thanks TigTex,
but I can safely say, the temperature problem is real. It's not just a false sensor, because of the heat, the metal-case of the laptop is generating. It really gets uncomfortable when working on that hot case (hands on the hot machine and typing - after a while you can order your hands "well done" *sigh*). Because of that, I switched to an external keyboard, but that's not really a solution. The weird thing is, that the temperature problem didn't exist at the beginning - and it doesn't exist on Windows. And it's also not a cleaning problem - I clean my machine regularly (because I hate dust, generally ).
I can also say, that the fan is working - and it's working also dynamicaly (gets louder, when the machine gets hotter).
I checked the CPU sensors on Windows with Core Temp regularly (runs automatically in system tray at boot).
The machine ran 20 minutes (after 1h I get around 70° C / 73° C / 73° C):
$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +67.0°C (crit = +106.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +61.0°C (high = +105.0°C, crit = +105.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +59.0°C (high = +105.0°C, crit = +105.0°C)
@litemotiv
$ dmesg |grep iwlagn
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
iwlagn: Copyright(c) 2003-2010 Intel Corporation
iwlagn 0000:09:00.0: enabling device (0000 -> 0002)
iwlagn 0000:09:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:09:00.0: setting latency timer to 64
iwlagn 0000:09:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54
iwlagn 0000:09:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
iwlagn 0000:09:00.0: irq 47 for MSI/MSI-X
iwlagn 0000:09:00.0: loaded firmware version 8.24.2.12
Xorg.0.log (using x86-video-intel):
[ 18.630] (II) intel(0): Integrated Graphics Chipset: Intel(R) GM45
[ 18.630] (--) intel(0): Chipset: "GM45"
I will check for powersaving features, thanks for the hinch.

Ipad 2 temperature problem since I have it

In January 2014 I exchanged my former ipad 2 to a new one using the out of warranty option. This new ipad 2 supposed to be a new one but it never worked because since the beginning I had this temperature problem that avoid me to use it for more than 5 minutes.
What can I do. Is this new ipad on warranty even I bought it using the OW? I paid $ 249+ tax!
Thanks for your help!

When you use the out of warranty option your replacement iPad does have a warranty just not as long as a new one. Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

K7N2 Temperature Problems

I'm having some small temperature problems with this board.
Here are the temps
CPU: 45-60 (normal-load)'c
Case: 38-45
Chipset: 42-47
The CPU isn't too bad, although I do see some strage fluctuations, like while writing this, its went upto 57 and then the next reading dropped to 47???
I have a laser digital thermometor which obviously can only scan temps external of the heatsinks, but it is accurate, and it does report similar temps.
My main worry here is the case temperature.
Here is my setup
K7N2 Delta 2
athlon 2.5 @ 2.2Ghz
1GB corsair (512*2)
Nvidia 6800GT 256MB DDR3
DVDRW
DVDROM/CDRW
120GB SATA HDD
500WATT PSU (which is heating up a little and could be a cause of this)
3 case fans
thermaltake volcano 12+
I've tried not clocking but there is little difference, room temps are at 20-25'c.
The heatsinks near the chipset seems to be getting rather hot also.
It doesn't have any stability problems. Its fine with games, no slowdowns. but its just the temps.
Can someone please compare my temps with the same board, just so I can get an idea.
Thanks in advance

I definitally need something black...
Otherwise it'd be a little out of place!
In all honesty I wish I could buy things from newegss. they seem to have a great range and nice system.
In the UK i'm reverted to buying from EBuyer (despite their poor customer services!), there prices are the cheapest although much dearer than the US...
http://www.ebuyer.com/customer/products/index.html?rb=3549119343&action=c2hvd19wcm9kdWN0X292ZXJ2aWV3&product_uid=54146
Its way out of my price range. I have £50ish set aside for it, and I'm looking at these at the moment all from overclockers (seem to have best range, not price) :
Sunbeam Samurai:
http://www.overclockers.co.uk/acatalog/Sunbeam_cases.html
Coolermaster Centurion 5:
http://www.overclockers.co.uk/acatalog/Online_Catalogue_Coolermaster_Cases_126.html
Antec SLK3700BQE Black Quiet Midi
http://www.overclockers.co.uk/acatalog/Antec_Cases.html
If anyone from the UK can reccomend somewhere that would be sweet!
I'm looking at:
Dabs
Ebuyer
Eclipse Computers
Redstore
Simply Computers
Aria.co.uk
Please I need more!

Strange but probably easy problem

Strange but probably easy problem...
I have made two pages recently. One for a company and one for
a game I'm making during my spare time. I have made them both in
the same way with an html page for every side.
The problem is that when it changes sides... On the first
page I made it looks like it leaves the back ground graphic and
just reload the text that has changed... this is how I want it to
be. But on the second it loads the backgrounds's every time...
These are the links... I hope someone understands what I mean
1st page www.ardent.se
2:nd page www.indylc2.com

cjh81 wrote:
> Strange but probably easy problem...
>
> I have made two pages recently. One for a company and
one for a game I'm
> making during my spare time. I have made them both in
the same way with an html
> page for every side.
>
> The problem is that when it changes sides... On the
first page I made it looks
> like it leaves the back ground graphic and just reload
the text that has
> changed... this is how I want it to be. But on the
second it loads the
> backgrounds's every time... These are the links... I
hope someone understands
> what I mean
>
>
> 1st page www.ardent.se
> 2:nd page www.indylc2.com
>
it's the same, but the first page loads faster than the
second.
seb ( [email protected])
http://webtrans1.com | high-end web
design
Downloads: Slide Show, Directory Browser, Mailing List

An EMU temperature problem occurred

Hello,
The error message I get is: "An EMU temperature problem occurred"
My Xserve RAID has been given me this error three times in the last month, always early in the morning. There is no temperature fluctuation in the server room as far as I can tell. The raid works fine and orange warning light comes on with no alarm. The raid admin initially reports failure, but when I click on the button it goes to green.
Is this a symptom that my controller is starting to fail? I cannot find anything on the web about this topic!

It wouldn't hurt to monitor the climate in the datacenter. We are using the weathergoose products:
http://www.itwatchdogs.com/
These will track temperature, humidity as well as sound and light levels, and airflow. You could also add probes that will monitor house power so you could see how long the systems have been running from UPS.
You could also download the SNMP MIB to be used with a third party graphing utility, such as Cacti.
These products have helped us to keep track of the cooling and overall health of our servers.

915gm-fr temperature problem

Hi! I´ve got a temperature problem, I just installed the Arctic Cooling freezer 7 cpu fan, to hopefully reduce the sound. But not!!! The fan runs at 2700rpm during cpu workload at 1% in windows, the bios is configurated to use temperature control. And the cpu temp in core center is 48 (pendle sometimes between 43- 60). I´ve tried some settings in core center but I think that program is crap.
The freezer 7 is icq cold. I want it to run in 1400rpm or less ( And I don´t think that is impossible), how can I control that? Or what is wrong?
Becouse the freezer 7 is ice cold there is no need for the fan to run at that speed. Maybe something is wrong with the PWM from the motherboard?
I think I´ve got a problem with the temperature control on the motherboard, reading wrong.
Best regards

I´ve got
915gm-fr motherboard
Intel P4 s775 3,0GHz HT
windows xp
BIOS version 1,6 (newest) and newest core-center
the cpufan is running at 2700+ rpm doing idle. !! =( and the cpu is around 50C
must be something wrong with the cpu temperature sensor?
I´ve never seen the fan speed slower, just full speed, even with the boxed cooler too.

Temperature problems with new imac

Anyone having unexpected hangs on the new iMac. I ran Techtool Pro and it detected a temperature problem. Anyone else have this. I have all solid state drives, and 16 gigs of RAM. G

You have AppleCare, bring it in to an Apple Store to have it diagnosed and repaired.

[HOWTO] fix throttling/temperature problems of GTX 870m (and probably others)

Hey,
The problem:
Other than repasting and undervolting using a VBIOS mod, you can't do much to prevent the guaranteed 93°C hit on the GS70 with the GTX 870m,
which results in serious throttling after a short while of full load on the GPU to prevent hardware-damage and thus, while playing, massive FPS drops. Also the mentioned "fixes" only delay the inevitable.
That's what I thought to be correct - turns out, it isn't.
This may work for any laptop/card combination with temperature/throttling issues, not only the GS70-2PE + GTX 870m!
I've found a way to circumvent the 93°C problem on the GS70 with a GTX 870m (may apply to other laptops/cards aswell):
The NVIDIA driver (and only the driver, not any hardmodded VBIOS) is able to set some stuff about the temperature target, you can't change with a hard mod - I've talked to svet about that.
Let's have a look some screenshots I took:
Screenshot #1 - default behaviour:
On the first screenshot you see the default behaviour of a brand new GS70-2PE with a GTX 870m - not repasted. It was taken right after I took the second screenshot, so there's still some amount of data left on the charts from before.
Have a look at the "GPU Core Clock" in GPU-Z. You'll notice big spikes (which go down to about 480 MHz) on the right hand side of the graph. That's the throttling the card automatically does when it's hit its 93°C temperature for about a minute. That are lag-spikes when playing something demanding.
You also notice on the "PerfCap Reason" row - when it was throttling in the "GPU Core Clock" row no soft performance cap was induced so this was done by the card (or the EC?) internally (that's the empty space on the right hand side of the chart).
Now let's look at the second screenshot.
Screenshot #2 - fixing things:
Notice the difference on the right hand side of both screenshots' "GPU Core Clock" charts. See the spike-downs gone in the second screenshot?
You can also see, that compared to the first chart, the driver has reduced the voltage to reach the Temperature Target while the clock rate was reduced.
Here I've slightly lowered the base clock of the GPU by -40 MHz, aswell as reduced the Voltage Offset by -18.8 mV. (Both settings may not even be necessary, please report your results)
This is the important part:
Additionally I've set the Temperature Target as priorized over the Power Target, and set the Temperature Target to 90°C.
As you can see when the GPU hits 91°C, after a couple of seconds it will clock down, but controlled by the driver (you can see that in the "PerfCap Reason" chart). It's not as bad as the drop to 450 MHz, it's just a 100 MHz drop, to about 810 MHz in my case. It stays there until it reaches a temperature of about 86°C, stays there a bit, clocks up again, and so on. (The clock values you see don't reflect the 810 MHz, the screenshot was taken while the PerfCap was not in effect)
Results
What have we gained?
No massive last-resort throttling by the card itself, but a small clock drop induced by the NVIDIA driver to meet our desired temperature target. A huge all-around performance improvement when the card gets hot and less FPS drops when playing for a long time or a GPU hungry game.
What have we lost?
Some few seconds of boost clock as the card clocks down a bit earlier. Also in my case I've lost 40 MHz of base clock (that may not even be necessary).
Combine that with a decent repasting and I'd call my GS70-2PE with a GTX 870m "stable" and reasonably fast on full GPU load.
By pressing the "Create Clocks Shortcut" button in NVIDIA Inspector those settings will be set on boot.
Please tell me what you think. Any improvements and experiences welcome.
panni

Quote from: bahadir.onc on 24-September-14, 18:37:57
Hey everyone!
I downloaded nvidia inspector to apply this fix,but shocked to see in default behaviour my Voltage Offset was -68.8. Should I change that? There is a big difference with the value the fix provides and my default value..
Also,I consider repasting with IC Diamond. Should I?
Hey,
the offset shouldn't matter - inspector showed some weird behaviour when modifying and/or initially setting it. Try to apply my fix and don't do anything to the offset as a first try to be safe. It shouldn't matter nevertheless, as we're talking about a very small millivolts value, nothing big.
Regarding repasting with IC Diamond: I've had great success in "repasting" using Liquid MetalPad - you might want to consider this.

HP 5530 Envy with error code B814E90A (probably network problem)

Bought this printer last January.Since a week it has the following problems:- makes a lot of noise during start-up (like something is a bit stuck)- tells me that I closed the printer incorrectly- gives the error code B814E90A- tells me that there's an error- I'm not able to use any button on the front/touchscreen of the printerAt a certain moment the printer told me it couldn't connect to the network. I tried to re-register, but kept returning in the loop mentioned above.I ran the printer-reset: didn't help. Today I took the printer to the shop where I bought it. The problems didn't occur there and the guy in the shop was able to connect the printer to the shops network. He advised me to reconnect the printer to my home network, and to ask the HP helpdesk about the error code, that he didn't know. As soon as I returned home and try to reconnnect the exact same loop was there again. The printer refused to reconnect to the network. I ran the Print and Scan doctor, installed new drivers, but the programmes tell me all that the connection fails.I cannot do anything on the printer to make it reconnect to the network again, reset those settings or ..... By now I'm pretty frustrated. This is an almost new printer. Best,Tanja

Hello, Please try the below steps. Power Off the printer while it is ON.Power off the router.Wait for 60 secondsPower on the PrinterMake a Copy ( black )Now Power On the Wireless Router.if issue still exists, then you may have to call ISP to change your router settings as mentioned below.Channel = 11, Frequenct = 2.4, Check for any update for Router.If issue still exists, its time to resplace the Printer. Kindly call HP Tech Support for further assistance.
If you are in US , the toll free # is 1-800-474-6836 .
If you are not in US , then log on to www.hp.com , at bottom-left corner there is a world map icon, click on it and then select the region you belong to, which would then provide support options for you for that region.

MBP 15' randomly shuts down: temperature problem?

Hallo,
I'm having a very serious problem with my MBP unibody (rev B). After a few minute of intense use (3D gaming or just streaming of HD flash video) it shuts down without any warning or alert. The event doesn't show up in the system log and it happens more often while using the 9600GT gpu.
It looks like a temperature managing problem, but the strange thing is that at the restart right after the sudden shut down the temperatures are absolutely normal and the fans seem to work as they should.
What could be the issue?
Moreover, I need my mac to work and I really can't afford to stay a day or more without it because it's in repair. It's still under official Apple warranty, am I eligible for an immediate full replacement?
thanks

Welcome to Apple Discussions
If it was shutting down due to over heating then you'd get some warning like the fans running at maximum revs for a while first ...
Are you saying the Console (All Messages) Log is not showing anything at all at the time of this event ??
It's probably best you contact the place where you bought it and have them take a look, there's nothing anyone can do here about hardware issues. It's highly unlikely you'd be given a replacement but any repairs needed would be covered by your Warranty.

User feedback: temperature problems with mac mini?

Being on the lookout for a new affordable mac (startup with "LC" then beige G3 DT, now G3 bw), I've inevitably come to the mini. So far I'm very exited, but the size somehow poses a little "problem" for me:
Does anyone have any practical feedback regarding heat development + reliability of the mini?
Glad to hear some responses!
G3 bw Mac OS X (10.3.9) 1 GB MEM, PowerLogix G3 zif Upgrade card 850 MHz

The lifespan of the mini as a product range is not yet sufficient to get a real good handle on reliability, though judging by the number of systems sold worldwide and the relatively sparse reports of system failures, the evidence would seem at this stage to point to them being at least as reliable as any other Mac, and somewhat more reliable than many other systems.
That isn't to say that mini's don't fail, because clearly some proportion of any production run will be intrinsically faulty, but the proportion in the mini's case seems low, and there has been little reason to doubt that internal temperature has had much to do with those systems that have failed. It is certainly not a concern I would have if I were considering buying one at this time.
Many people have voiced concerns over the size of the system, though curiously, many have also said they would not have the same issues with a laptop, which typically run hotter and with more confined internal space and smaller fans!
My view is that since Apple have a pretty good track record of taking engineering concerns into account in their industrial design, there is a very high probability that the designers and engineers involved in developing the mini took steps to ensure the system was not compromised by inherent flaws that would risk failures. It would be incredibly surprising if they had not studied heating issues and ensured the cooling system was adequate to the task.
I also think it important to consider temperature not in the absolute sense, but as part of a heating/cooling cycle, since a high, but steady state, operating temperature is no where near as harmful as one which fluctuates between cold and hot. The former simply requires good control and components designed to cope with the heat level anticipated, the latter causes heat stressing and failure. The mini's cpu-load reactive cooling system is designed to ensure the temperature remains as steady as possible during a wide range of uses.

Nokia 5530 battery stripes problem

I've had some troubles before with my screen going black and then the phone turning off, but now I got a problem with the battery stripes. After I charge my phone it says 7 stripes and when I start using him, it will stay at 7 stripes until I restart him, then some stripes are disappeared and the stripes go away normally again. Yesterday it went from 7>6 stripes and when I restarted him there were only 4 stripes left. I really don't understand what could be wrong, but I can now never know well when my battery should be charged...
Nokia 5530 XpressMusic Black-Red

Hi vnqshrz,
Thank you for your post and a big welcome to the Nokia discussion forums.
From your post I can see that you have updated your firmware, tried resetting the phone and have tried a different battery and charger combination as well.
What I recommend you do is contact your local Nokia care line. You can find the details on the below link:
http://www.nokia.com/ph-en/support/contact/
Let me know how you get on.
Regards
Raoul_Duke
If you find this post helpful, a click upon the white star at bottom would always be appreciated.
If it also solves your problem, clicking ACCEPT AS SOLUTION below it will benefit other users!

Screen color temperature problem!

Hello this is my first post on here. I just picked up my second BB 8330 from sprint today it was a replacement for an unrelated matter. The first thing I noticed was the screen seems to be dimmer than my old one and the color temperature seems a lot warmer. I did the usual things, I made sure it was on 100% brightness, checked the auto-dim etc and the problem is still there. I did some searching around on the net and the best solution I can find is that there is problem with the screen manufacturer in Mexico...whether this is true or not I really have no idea. In any case there doesn't seem to be a solution out there, I was wondering if there was a firmware update or patch that I didn't know about? Any and all suggestions are welcome.

check out Robot ..getPixelColor(int x, int y)

5530 (probably) temperature problem

Similar Messages

Maybe you are looking for