5800 language problem

assalam alaykom
about 2 days ago when I was connected my 5800 XM
to OVI
he told me I can update software
and I do that immediately
and change from v 51
to v52.0.101
the problem is the phone don't have Arabic language ( writing only)
I can read Arabic but can't write Arabic
how I can fix this problem

If the problem appeared after the firmware update.. in all probability the phone was not intended to be sold in your region.. but the retailer added the language pack and sold it in your area for his personal gains.. Though you may try going to the retailer and explain the situation to help you out..( should be a Free of cost install...)..if that can not be of help, then the ONLY solution is to visit Nokia Care and get the language pack installed. It may cost you a little..but be warned that any future firmware upgrade..(.. IF and when available..) will again result in the language missing that will again need to be installed...

Similar Messages

5800 Wifi Problems

I know this has been mentioned a few times - but reading them does not help me:
I have a wifi network set up at home on a Netgear Router. I have a few things connected to it via wifi and not had any problems.
My network is set up with a hidden SSID, mac address filtering and defined IP addresses for all the mac addresses so when each device is attached it always gets the same IP address.
I have entered the mac address of my 5800 no problems there: However, when I try and connect the 5800 to the internet through my wifi I get nothing.
I have tried using the wireless wizard which says the connection is made, my password is correct - but I just cannot connect to the internet through my wifi?
Any suggestions? My phone has the latest firmware - just cannot get a wifi connection at home

If the MAC Address is showing in the list of connected devices, then I suspect that it is not a problem with the MAC filtering.
With regards to DHCP, this is the system that allocates an IP address (and other information) to devices connecting to your network. Check on your wireless router settings, there should be something that says DHCP is enabled or not. If DHCP is not enabled, then your device will not be able to acess anything on the network without manually entering the IP information.
If DHCP is not enabled, try to enable it and see what happens then.
Dave -
Phones:3110,5110,6110,6210,6310,6310i,8210,8250,8310,6230,6230i,6280,E60,E65, 5800, N900
and: 7110,6250,6220,6111,7370 (but just for a few months)

Language problem in JSP please help

Hi all java guru;
Altough I tried all different way I can not solve the my problem.
My problem is Turkish language problem in JSP.
If my jsp page use database applications such as push or pull data to my SQL 2000 database or call some datas from database, some data which contains turkish caracter are seen wrong. suc as �� is to ??????
what is the problem?
But important point is that; this is only Database data which come from sql database. But I can see JSP data or HTML data truly.
I try different method to solve in JSP page;
1-request.setEncoding("iso-8859-9");
or
request.setCharacterEncoding( "windows-1250" );
2-
@contentType="text/html; charset=iso-8859-9"
@page pageEncoding="iso-8859-9"
3-
<meta http-equiv="Content-Language" content="tr">
<META http-equiv="Content-Style-Type" content="text/css">
4-
ISO-8859-9 is turkish charecter spefications
String TR_tlp = new String(NEW_TALEP.getBytes(),"ISO-8859-9"); // this parm is inserting database but problem is go on.
5-
for the database...
Properties props = new Properties();
props.put("user","login");
props.put("password","password");
props.put("charSet","UNICODE");
6-
url= "jdbc:microsoft:sqlserver://IP_NO:1433;databasename=database;TRUSTED_CONNECTION = true;CHARSET="+sun.io.ByteToCharConverter.getDefault().getCharacterEncoding();
or
url= "jdbc:microsoft:sqlserver://IP_NO:1433;databasename=database;TRUSTED_CONNECTION = true;CHARSET=ISO-8859-9"
con= DriverManager.getConnection(url, kulad, sifre);
I am using tomcat 5.0.19,
is there any way to solve this problem... Please help......

Were you ever able to solve your problem?
I have a similar problem.
My database is storing the characters correctly and they can be viewed in Java, but when I try to convert them to unicode using:
String inputUtf8 = new String(input.getBytes(),charset);
it works for almost all characters, but some come through as noncharacter "boxes."
The characters that come through as boxes in iso8859-1 are the ones that are in the "supplementary" character range of that set, such as:
- curved left and right quotes
- "TM" symbol
- bullets
- m dash and n dash
(see this table: http://www.csgnetwork.com/htmlchrset.html for a more complete list of the supplementary characters )
Any idea what I need to do to have these characters show up properly?

Language problem with Safari!

I can't view the Arabic language correctly with "Safari". I chose the "Arabic (Windows )" as my "Default Encoding". I'm using "Safari 3.0.3 (522.15.5)". My OS is "Windows Vista Ultimate". "Arabic" is my current language for non-unicode programs. I don't have this language problem with neither "Internet Explorer 7" or "Firefox 2.0.0.7". I really like the "Safari Web Browser" but this problem si really annoying. How can I solve it? Thanks!

Try to run nightly version of Safari: http://nightly.webkit.org or wait for final version of Safari. Localization issues are major known bugs in Safari.

Nokia 5800 Serious Problems not Solved??

I have been using 5800 for over 4 months and I have updated my firmware whenever it is available but none of the firmware updates solved the following very serious problems that turned my phone into a useless thing:
First thing is the text messaging problem:
-While writing in Turkish language, while the number of letters in a SMS got higher and higher just a little bit(more than 50 characters), writing a SMS became painful, because it got slower and and slower so you cannot write your SMS properly and fast! The last thing that make me crazy is that I write a SMS more than 300 characters in over 10 MINUTES!!! (This problem must immediately be solved)
I hoped that v21 update will solve the problem but it did not, my older Nokia 1110 can write SMS under a minute no matter how long is the SMS is...
Second problem is the snyc between phonebook and calendar:
-The problem is that you can add birthdays under persons in phonebook but why cannot we set those dirthdays as calendar events???!!!
V21 neither solved this problem!
Third problem flash not full screen!:
- The last thing is that when ever I start a flash .swf file in works properly but when I try to change the resolution to full screen, a useless screen keyboard pops up and you cannot chose to close this, so in reality you cannot use flash .swf files fullscreen!
The problems above are serious problems, that make the phone useless and must immediately be solved,
DOES ANYBODY HAVE A SOLUTION FOR THE PROBLEMS ABOVE?
THANKS FOR YOUR ANSWERS ANYWAY...

[quote]
Third problem flash not full screen!:
- The last thing is that when ever I start a flash .swf file in works properly but when I try to change the resolution to full screen, a useless screen keyboard pops up and you cannot chose to close this, so in reality you cannot use flash .swf files fullscreen!
[/quote]
The third problem there is a workaround: create a mini webpage with the following content::
(replace 'myflashimage.swf' by the name of your swf).
<html><<head><title>My Flash</title></head>
<body>
<object classid="clsid:d27cdb6e-ae6d-11cf-96b8-444553540000" codebase="http://download.macromedia.com/pub/shockwave/cabs/flash/swflash.cab#version=9,0,0,0" width="520" height="420" align="middle">
<param name="movie" value="myflashimage.swf" /><param name="menu" value="false" />
<param name="quality" value="high" /><param name="bgcolor" value="#000000" />
<embed src="myflashimage.swf" menu="false" quality="high" bgcolor="#eeeeee" width="520" height="420" name="myflashimage" align="middle" allowScriptAccess="sameDomain" allowFullScreen="true" type="application/x-shockwave-flash" pluginspage="http://www.macromedia.com/go/getflashplayer" />
</object>
</body></html>
Nokia 5800
FW 30.0.011

Nokia 5800 Sound problems in music player

Having a weird problem with the music player. When you choose a song to play, there is no sound unless you press either volume button, then the sound works normally. I have tried this in all different profiles, with and without headphones and nothing seems to work. Any ideas how I can get the sound back in the music player?

I don't know the exact solution to the problem but you may try to do a reset option. Sometimes with my N82 the sound just stops but the music is going. So i pause and play it again.
Try this reset but-
Before perfoming this please take a backup of your data.
Factory defaults-
Type *#7780# on your standby screen.
This will reset all your setting to default factory settings. User data wont be affected.
Soft reset-
Type *#7370#
This will reset the phone as well delete user data. Use when want to format the phone.
If none of these worked then you might want to do a hard reset.
For this you have to-
1. Switch off the phone.
2. Hold down the following three buttons: Green (the call answer button), * button, and '3' button.( Just in case of N78 it will be the multimedia key the small silver key on right side & for Nokia 5800XM - use the following buttons to do a hard reset, GREEN/RED/CAMERA keys pressed all at once on power up. this will only work on 5800's that have firmware version 20... and up. For Nokia N97 is SHIFT /SPACE BAR / BACKSPACE. )
3. While holding these buttons, hold the power button to switch on the phone.
4. Release the buttons when the phone shows the nokia hands logo or shows other signs of life like the language selection screen.
Please thank me by giving 'KUDOS' star. It will help me to serve you better.
Currently using N82 and 5230. Next would be N?

Problem with Flash Lite in Nokia 5800 XpressMusic-Problema con Flash Lite en Nokia 5800 XpressMusic

I've got a problem playing videos in YouTube with my 5800. Recently I updated my version of Flash Lite to 3.1, from that day I can't see correctly videos on YouTube, when the the indicator of the bar reaches 1/4 of the totallity of the bar, the sound and image stop, but the indicator continues playing. If i want to see completly a video I have to put the indicator in the start of the bar and wait the load again. Some idea to fix this problem?
Sorry for my English level.
Tengo un problema reproduciendo vídeos en YouTube con mi 5800. Hace poco actualicé la versión del Flash Lite a la 3.1 y desde entonces no puedo ver correctamente vídeos de YouTube, cuando el indicador de la barra alcanza 1/4 de la distancia total, se detienen el sonido y la imagen, pero el indicador continúa como si siguiera reproduciendo, es decir para el vídeo es como si siguiera reproduciendo pero ni el sonido ni la imagen continúan., para ver los vídeos tengo que llevar el cursor de carga al principio y esperar la carga de nuevo, es un problema realmente molesto. ¿Alguna idea para solucionarlo?

Hi,
I have Nokia 5800XM as well. The YouTube videos are playng fine for me. my FW is 40.0.005 with FL3.1
Maybe you need to update your device's firmware and FL version.\
Start Device Manager application on your 5800XM from menu or dialing *#0000#. It will check for new updates and ask you to download them. Remember that these updates are in MBs. I'd recommend update using a WiFi connection or flat-rate data plan.
Best,
// chall3ng3r //

Language Problem while exporting and importing data

hi,
I have Oracle version 8.1.7.0.0 installed on one server and 9.2.0.1.0 installed on new server.
I'm copying and pasting my version info from SQL*Plus:
SQL*Plus: Release 8.1.7.0.0 - Production on Mon Aug 22 10:46:31 2005
(c) Copyright 2000 Oracle Corporation. All rights reserved.
Connected to:
Oracle8i Enterprise Edition Release 8.1.7.0.0 - Production
With the Partitioning option
JServer Release 8.1.7.0.0 - Production
SQL>
SQL*Plus: Release 9.2.0.1.0 - Production on Mon Aug 22 12:30:06 2005
Copyright (c) 1982, 2002, Oracle Corporation. All rights reserved.
Connected to:
Oracle9i Enterprise Edition Release 9.2.0.1.0 - Production
With the Partitioning, OLAP and Oracle Data Mining options
JServer Release 9.2.0.1.0 - Production
SQL>
I created new user on my new server from enterprise manager.
Exported user from the old server and imported in the new server.
i.e: from Oracle8i Enterprise Edition Release 8.1.7.0.0, I did
c:\>exp system/manager file=abc.dmp owner=abc
Then on the new server Release 9.2.0.1.0, I did
c:\>imp system/manager file=abc.dmp fromuser=abc touser=abc
I'm using Arabic Language on my both servers. NLS_LANG parameter on both the servers is AMERICAN_AMERICA.WE8MSWIN1252.
On both the servers I'm able to insert and select data in arabic.
However, after I export the data from old server to the new server, the arabic data comes in question marks.
If I create new table and insert arabic data on new server's user abc it is displaying well. Only the data which I exported and imported is not showing arabic.
On both old and new servers operating system is Windows XP.
I'm stuck with this problem. Anybody having any idea about how to solve this problem please help.
Thank you all in advance.
Regards

Let me be clear here. Storing Arabic data in a WE8MSWIN1252 database is not supported by Oracle and will lead to problems. You are incorrectly using the NLS_LANG to prevent proper conversion and your data appears to be okay when you use utilties like SQL*PLUS to view your data. When you write applications that don't rely on the NLS_LANG like JDBC thin driver for instance you will realize your data is in fact invalid. To learn more about the NLS_LANG you can take a look at this FAQ: http://www.oracle.com/technology/tech/globalization/htdocs/nls_lang%20faq.htm
To migrate your database to a proper character set you can refer to this paper:
http://www.oracle.com/technology/tech/globalization/pdf/mwp.pdf
But please do not ask for help in supporting your current configuration in this forum.

Mavericks OSX Update 10.9.1 is out - fixes language problem

See: http://support.apple.com/kb/HT6065
The new update to Mavericks fixes the problem with updates not showing, if the primary system language is not set to English:
Fixes an issue that prevented iLife and iWork apps from updating on non-English systems
It does not mention Aperture - but hopefully this problem has been fixed for Aperture as well with this update.

Actually, this is an id10T mistake. I rebooted to the wrong hard drive. Please disregard this problem. It is solved.

Korean language problem - stops mail sending

Hey there.
I have an unusual problem re mail from a Korean client. Some of the characters are cached when I reply to mail from them and it then won't send with any smtp server - i've tried many.
Is there a way of turning off the Korean language support to stop this happening?

Is there a way of turning off the Korean language support to stop this happening?
System Preferences>International, uncheck Korean in the Language & Inout Tabs... may require a restart to work.

How do i fix windows 8.1 unknown language problem

Hello Sir,
I am one of your Microsoft Users, i am using 50 licenses Windows 8.1 Professional version 64 Bit for my official use.
From last six month i am facing this Issue So Kindly I'll request to you please look into this.
The problem is Every time some Unknown or Unidentified language appear in my desktop i can't browsing i can't do anything with this, That's why i already tried 3 times reinstall of my windows with official license key but not fixed.
I already reformatted my desktop approx 3 times but still it's not fixed i already scan my whole HDD but still it's not fixed.
So please give me the Solution on this ASAP. Kindly also make sure with my attached screenshot.

First of all thanks for your reply.
I doing that only System restore & reformatting my HDD. and reinstall the software again.
And even i am also shocked i never seen this types of error. in my 98 Years IT Carrier.
I think so but i am not sure my colleague installed some Fonts. for the use of (Adobe Photoshop CS6) or something like that ? Because this one is my designer desktop.
Kindly also make sure with my Specification.
Intel Core i7 4th Gen 4770k
Intel DH 87 RI Mother Board
Kingston DDR3 8GB Ram
Seagate Sata 1TB Hard Disk
Kingston SSD Drive 120GB
Cooler Master CMP251 Cabinet
VIP 500W(Golden) SMPS
Cooler Master Devastator Keyboard Mouse
Dell S2240I 22" TFT
Zotac GTX650 2GB Graphic Card
Quickheal IS Antivirus 10 User
Vinay Gohil

Adobe master collection CS5.5 5.5 MLP arabic language problem.

Hi all of you,
We have “master collection CS5.5 5.5 MLP international licensed version” it’s working fine but in Photoshop Arabic language is not working properly , I tried with a Photoshop CS5 extended middle east version it’s working fine in Arabic language . Is there any solution for this problem? Can I get any Arabic language pack for Photoshop?

Moving this discussion to the Photoshop General Discussion

Adobe Photoshop Elements 10 Language Problem

Hi all!
I've a problem with Adobe Photoshop Elements 10 Editor.
I bought Elements 10 Editor from the app store (I've a Mac) some months ago and I chose the english language during the installation.
Today it happened that, when I opened it, I found it totally in German! How can I restore english language?

This has been happening a lot to people who upgrade to Yosemite. Here's what adobe suggested a couple of years ago when it was happening to a few people:
Mac App Store version is German | Photoshop Elements

Script language problem

Hi friends,
We designed a script for purchase order for taiwans, and it is
displaying the incorrect Payment Terms when outputted (e.g. printed) using the ZEBT(own outtype) output type in language 'ZF'. The Payment Terms text displayed in the ouputted form is not the correct text for the Payment Term on the Purchase Order.
and it is displaying correct when the outtype in language 'EN'.
can any suggest me on this, how it is happening.
Thanks.

HI friend..
I have faced the same problem very long ago..
Try to debug the script first in se71.
At the main window look for the field netwr....
Just do some checking there..
Otherwise i can think for u some other solution...
regards..
saravannan...

Language Problem in BEX

Hi Everyone,
I am facing a very peculiar problem. I have installed SAP GUI 7.0. When I open the BEx Analyzer all Icons in the toolbar which are related to BEx are coming in different language. I have installed that 'n' number of times....restart the system installed it again and again but nothing is working out. Checked all options in administrator etc. everywhere default language is English.
Can anybody help me out.
Thanks

Solved

5800 language problem

Similar Messages

Maybe you are looking for