5D Mk III L-bracket on 5Ds???

Will an L-bracket made for a 5D Mk III fit a 5Ds correctly? The specs on the Canon site show the same dimension for both, however, I assume the depth is measured from the back surface of the body to the front surface of the lens mount. That does not mean that the distance from back to front across the bottom plate is the same on both hence my question. Thanks.

See this. It's about your question complete with a photo. http://www.fredmiranda.com/forum/topic/1370974

Similar Messages

I need to import raw images from canon Mark iii

how can I do this in 4? Do I need additional software?

Just received our 5DS Mark III and as I understand it you need LR4.1 RC2 to read the RAW files, downloading it now to give it a try.

Adding an SSD (SATA III) to HP Elite desktop. Is it possible?

Dear Experts...
I would like to upgrade my computer adding an SSD drive as a master drive and shifting the original 2TB drive to be a slave.
I found several coices of SSD drives but almost all of them are SATA III interface.
Does my desktop supports this interface? as it is just written that it has a SATA interface without specifying which version of SATA!
How many hard drives could this desktop holds? I already have two (the original 2TB, and my old 256GB drive), and I wand to add one SSD for Windows and progs.
Can I buy this SSD for example? Samsung Electronics 840 EVO-Series 500GB 2.5-Inch SATA III Single Unit Version Internal Solid State ...
This is the official HP specifications page of my Desktop .
Thank you in advance for your help.
This question was solved.
View Solution.

Hi,
It has 2 spare HDD bays as on its specs:
http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c02781215
You can swap SSD on your machine and make the old HDD as a secondary ("slave") drive. SATA III is backward compatible therefore you can use it. Since SSD's are smaller (normally 2.5") you need something which is similar to one of the following brackets:
http://pccasegear.com/index.php?main_page=index&cPath=210_901
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Boot up hangs at system power on(all LED's of D bracket are on.

Building a new computer for a friend. 915P Combo-FR mother board with 1 gig DDR 400 RAM, 3 GHz Prescott Socket 775 P4, MSI GeForce 660 PCI Express with 256 RAM, Thermatake Xaser III Lanfire with 420 Watt powersupply. When powering up no beeps or nothing just all four lights on D-bracket? Reinstalled the CPU, and everything looks OK. The only question is the CPU fan. This is on so tight the motherboard bulges, when looking from the back of the board, I don't remember this with my 478 socket installation. Anywhere to start?

I installed RAM from my computer into my freinds witch has the same DDR 400 RAM and the boot up is the same. I am currently using the new RAM in my computer with no problems at all. I already changed out the motherboard and RAM and still not boot. I rebooted the computer with the video card out of it and still no change. This is why the CPU is on my list. I don't think it is the RAM because I have changed it out as well. Don't know what else to do.

SATA II or III on late 2010 MBP - Also SATA III and SSD performance

Hello:
I would like to confirm that only the new 2011 MBP's have 6gb SATA interfaces. My MBP reports Series 5 and 3gb on both optical and HD bay. I have an SSD in the optical bay and a WD Scorpio Black in the HD slot. Both have a negotiated link speed of 3gb. I put the SSD in the optical bracket and the spinning drive in the real drive slot to take advantages of the physical protection in the HD bay.
If the new MBP's have one SATA III channel, I would assume it's important to put the SSD in that slot.
My SSD has a SATA II (3gb) interface. Some new ones have 6gb. Do SSD drives even approach that throughput or 3gb throughput? Which leads to the question, would a SATA III SSD perform better in a SATA III MBP?
I know the benchmarks may not even be noticeable in real life use for most of us

I have just out a SSD on my 2010 MBP, from all the info i could find both the HDD and optibay in the 2010 late SATA II, this is the reason i put my SSD in the optibay as the speed would be the same.
I did think about getting a SATA III SSD for the future when i upgrade but at the time they were very expensive and i had read reports about problems connecting to a SATA II.
The new MBP do only have SATA III in the HDD spot so this would be the best place for any SATA III SSD.
Personally on a 2010 MBP im happy, i still get great speeds Vs a HDD but with keeping the HDD in its original spot i get to keep spin down and the motion sensor.

NO SOUND / S-Bracket or On-Board / 865PE FIS2R - HELP!!!

Hi everyone, I need some help PLEASE!!!
I have a HUGE problem, the machine I have has been running really sweet. Everything is new except the old sound card I was using (Sound Blaster Live Value), anyway the machine worked perfectly as was assembled but my brother-in-law called me and told me he really needed my sound card. I was like cool, I'll give him mine, install the S-Bracket and use the on-board sound for 2 or 3 weeks then I'll get a really nice sound card like an Creative Sound Blaster Audigy Platinum or Pro. So I went through the manual and check list. I removed my card and installed the S-Bracket. I've done everything correctly but am getting no sound. I made sure to enable Audio 97 in the BIO but still nothing, I also removed the jumpers recommended by bio when installing the S-Bracket
I haven't even been able to install any drivers and now am unsure if I'm even using the right disk that came with my 865PE. There's 2 disk, one called the Super Pack which has Photoshop, WinDVD, etc . . . so I'm assuming it's not in that one. Now the other one is the MSI Drivers and Utilities Disk. Under the MSI menu I can't find anything for sound. But if I explore the disk I find a sound folder. Well I've tried installing every driver listed but am getting the ERROR (Not equiped with this Audio chip, etc . . ) IF ANYONE has had a similiar problem or seen a very similiar post please let me know. I REALLY would like to get my on-board sound working. I don't have the cash right now for a new sound card.
THANX, Guru
3D Mark01 SE Score - 16464
Case - Thermaltake Xaser III to keep things nice and cool.
Motherboard - MSI 865PE-FIS2R - Bio 1.7
CPU - Intel P4 2.8 Ghz 800FSB - OVERCLOCKED to a 3.15GHz
Memory - Kingston Hyper X KHX3200AK2/1Gig PC3200 400MHz 2-3-2-6-1
Video Card - eVga Nvidia FX5900 based 128mb (non Ultra) 420MHZ/920MHz
Sound Card - Creative Sound Blaster Live Series
HDD - 2 40gig Western Digital 7200rpm

Weird, well while waiting for a reply from MSI Support I decided to update my BIO from 1.7 to 1.9 Machine restarts and BAM! I have sound. So now I put the driver and utilitie disk back in and there are a few more options including C-Media software and drivers. So guess I'll install the software and ready to rock. Weird if you ask me that the bios upgrade caused it to realize the S-Bracket was on and that there was an on-baord audio chipset.
Thanx, Guru

Can i install sata III hard drive?

Hi, i've an iMac G5 20" iSight with an intel core duo 2ghz. I would like to know if i can install a sata III hard drive like 128GB Crucial m4 2.5" SSD.
Thx a lot.

First, you do not have an iMac G5. G5s are PPC machines, but yours is an Intel model.
You can install a SATA III drive but I would not spend the money since your model only supports SATA I or SATA II depending on which model you have. I would also be careful about using Crucial SSDs because they may not all work in a Mac. I would get your SSD at OWC instead. You will find their equivalent product for SATA I or SATA II here. I have two of these drives, and they are excellent.

Bracket in Regular Expression constant?

I am a bit puzzled by the behavior I am experiencing in LV 2011. I hope to get some light from experts out there.
I am trying to parse a messy ASCII header file and after having split it into individual lines (strings), I use the "Match Regular Expression" function to remove some of the info before the substantial information.
Some of the strings include square brackets ([, ]), which are special characters for the function, therefore, as documented in the help, one needs to precede them with a backslash.
Example:
I want to parse the following line:
#PR [PR_DEV,I,2]
One way (which I am using because of considerations related to the rest of the header) is the the following:
Note that the first string constant is using "Code Display" whereas the second one is using "Normal Display".
Why did I not put a backslash in front of the bracket in the first string, you may ask? Well, I did, but it disappeared after I typed the other characters. And reverting to "Normal Display" did not restore it.
Of course, the first version does not parse the input string correctly, whereas the second one does it fine.
In other words, the custom display string (which is convenient for cryptic codes such as \s* or to distinguish between space and tab...or simply ENTER tabs!) seems to mess up with the \[ combo (likewise with the \] one).
It is not a huge deal. I can use the "Normal Display" mode, but I tend to think that this qualifies as a hidden "feature". And again, it is still a pain in the ... when dealing with special characters such as tabs, etc...
Solved!
Go to Solution.

I think that [ is a special character which needs to be preceded by a backslash, but it is not one of the defined backslash characters (like \s). So, you need to put in two \\ to get one \ while in '\' Codes Display.
You can put in any character by using \xx where the xx is a hex character using only upper case letters for A..F. I converted the strings to byte arrays and tried to see what made the arrays match and the Match work.
Lynn

DeckLink HD Extreme III HDMI capture

Hi
I wont to use a BlackMagic DeckLink HD Extreme III card in a MacPro using Final Cut Pro 7 to capture a HDMI signal and capture the audio from a separate XLR source. Does anyone know if this is possible please?
Thanks
Paul

well you are shooting JVC's proprietary HDV variant ... if you want to capture the native MPEG-2 transport stream from the camera or deck then you need to capture via firewire. If you capture via component then the camera is decompressing the video data and sending that decompressed data down the wires to your Decklink where it is being recompressed to the target codec ... you might set the target codec to the same HDV variant that you shot but in capturing it as such you have pushed the signal through a full recompression cycle.
if you've had troubles with capture of the JVC originated footage then you might find good info here:
http://www.aulich-adamski.de/en/perm/how-to-handle-jvc-hdv-720p-scene-breaks-in- final-cut-pro

MSI HD6950 Frozr III 2gb screen lock up

Hi I'm asking for help before I have to return my MSI HD6950 Frozr III 2 GB graphics card.
I Have a self built system that comprises of the following: ASUS M4A88 T-M motherboard
AMD Phenom 955 Black Edition Quad Core Processor (not overclocked)
8 Gigs of Corsair 1600 RAM - Windows 7 64 Bit all windows updates
750 watt Antec PSU
1 TB Samsung F1 Hard Drive
(Had 1 GB Nvidia GTS450 - the system has run beautifully since I built it in August, no crashes, lock ups etc)
Bought the beautiful HD6950 and installed it ok, installed the latest Catalyst 11.10 drivers, it ran ok for a short period of time, but then in games it started to lock up, this resulted in a beige coloured screen with very thin vertival dark lines, could not CNTL/ALT/DEL out of it, had to reset. Windows then will not run up normally, so I have to try safe mode. Safe mode comes up, but attempting to system restore ends in failure and after applying all the saved data it sits there with a blank screen. This then results in reset and safe mode yet again.
I have been on AMD's website but this just results in dozens of possibilities dating back 3 or 4 years. One of the moderators suggested your site as it is MSI equipment and thought it more useful in attempting to find a fix for this issue.
I have while in safe mode deinstalled the graphics card and relaunched the system, Windows will then come back up again using windows generic drivers, I then re-install the latest Drivers from AMD's site, and when prompted to I restart the system, this then sends me back into the cycle of failing to load up Windows yet again. And has gone on like this for several days now, I have done loads of suggested things to attempt a fix, all to no avail, Virus checked, even bought a new PSU in case my old 550 watt unit was lacking power, I have reseated all RAM and checked my RAM in windows, reconnected all power cables, reseated my graphics card, all to no avail.
I was now starting to doubt my system, so in desperation, I deinstalled the HD6950 and put back in my GTS450, what a difference, the system is stable and a joy, its how I was expecting the system to behave with the HD6950 in, obviously I would ideally like the extra graphics clout of the HD6950 in but I'll settle for stable and rock solid instead. One clue I may have is I noticed that it tended to lock up when the GPU's fan increased in speed, from its low and quiet mode of operation. Please help as I want to give you 6950 the best possible chance, but I cant go on with it like this.....
Yours Sincerely

sent the card back to reseller to check it and replace it if needs

K7T Turbo D-Bracket USB connector?

Please I need some help.
I have a K7T Turbo Limited Edition Motherboard 6330 V.30 . It came with the P2P USB Bracket and the D-Bracket.
I can only find one place on the motherboard for a USB connector, how am I supposed to install these? Is there a mismarked motherboard pinout?
My Motherboard manual says it has a connectors for 6 USB ports.
I have 2 near the PS2 connectors built in, the D-Bracket has 2, the P2P has 2 which = 6, but I can't find a place to plug the brackets into the motherboard.
I would appreciate any help in the matter at all
Neoghost

Hi
According to the MSI site for the K7T Turbo Limited Edition, your motherboard only supports 4 USB connections.
You can use a USB PCI card to obtain more if needed.
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=25

R835-P56X:i can use SATA III (6.0 Gb/s) Now

R835-P56X：i can use SATA III (6.0 Gb/s) Now
1.BIOS Update to 3.0
2.My OCZ Vertex3 SSD firmware update to 2.11
3.install Intel RST Driver
Attachments:
02.jpg ‏115 KB
03.jpg ‏118 KB
01.jpg ‏110 KB
atto.jpg ‏128 KB

I emailed Toshiba regarding this issue and this is their reply:
Hi!
"On Fri, Oct 28, 2011 at 9:08 AM, Contact Us <[email protected]> wrote:
Hello Tor
The SATA 111 will be launched mid 2012 and do not have any clear details as of yet.
Regards,
Inside Sales
Toshiba of Canada Limited"
I am very happy with my Portege R835, except for the sata-issue....severely limiting my SSD speed, as I as many others bought this computer specifically because I thought it supported Sata 3. It is absolutely horrific of Toshiba to limit the sata speeds without telling their customers about it!! They will definitely lose thousands of customers on this rather stupid move of theirs. Unbelievable!! Why ruin such a good computer. Sell customers a Ferrari not telling them it's speed limited to 80mph. Toshiba; be up front about such vital information to your customers!!!

What is difference between SUNW,UltraSPARC-IIIi and US-III+

Hi All,
I am trying to finalise a VxVM version for a Solaris 8 version. On the Solaris machine I see,
System Configuration: Sun Microsystems sun4u Sun Fire 280R (UltraSPARC-III+)
System clock frequency: 150 MHz
Memory size: 4096 Megabytes
========================= CPUs ===============================================
Run E$ CPU CPU
Brd CPU MHz MB Impl. Mask
A 0 1200 8.0 US-III+ 11.0
On the compatibility matrix I see only Ultra Sparc IIIi and no III+ . Are they both same or hugely diffrent?
Please help.
Regards,
Anand

Google
["SPARC IIIi versus SPARC III"|http://www.google.com/search?hl=en&q=SPARC+iiii+versus+sparc+iii&btnG=Google+Search&aq=f&oq=]
Find Ben Rockford's blog comparing Sun's cpu architectures.
[http://www.cuddletech.com/blog/pivot/entry.php?id=332|http://www.cuddletech.com/blog/pivot/entry.php?id=332]

Tecra A8-103 Port Replicator III does not work on WIndows 7

Hi 2 all,
My Tecra A8-103 worked very fine with docking station: Advanced Toshiba Port replicator III plus.
It worked well on Windows Vista.
but, after Windows 7 was installed, docking station does not accept/recognize microphone and stereo input ??
I mean, when I connect microphone jack and jack from external speakers into docking station, there is no sound ??
are there any drivers perhaps ? to be installed for Windows 7 ?
thanks in advance
Zoran

I have a MacMini that is a intel core solo and has the DVI port not the mini-DVI.
I was able to load win7 but only after connecting the MacMini to an LCD monitor via DVI-to-VGA converter that came with my mac mini.
I am running snow leopard on the mac side and the video works great in 1080p via DVI cable direct to my DLP tv. but when I loaded win7 the tv couldn't display the video feed. The tv read "not compatible data". The DLP tv has a VGA input and win7 is running fine on it.
I am looking for a way to enable the video card to give the same quality on the win7 side as the OS X side, so that I can go back to the DVI cable and the 1080p I was getting in snow leopard.

Working on existing document; two forms of page numbers (starts as i,ii,iii and moves to 2,3,4)

I inherited a facing-pages document with two master pages. They are supposed to have page numbers in them (1,2,3,4 etc) but the first few pages of the document are i,ii,iii etc. and I can't figure out how to change them. Can anyone help?

That's pretty standard formatting for a document divided into sections withthe first section containing front matter and the "real" page 1 appearing further into the file. What's the first page number after the i, ii,iii ... series?
Number style is changed by slecting the first page of a section (it will have a small triangle above it) in the Pages panel and going to the Numbering And Section Options where you will find a drop-down for number style. It's a bad idea to have multiple pages with the same logical page number using the same number style, and ID will complain.

5D Mk III L-bracket on 5Ds???

Similar Messages

Maybe you are looking for