6.0.2 exe .vs. 6.1 exe

Greetings ... I have some compiled EXE's (compiled under both 6.0.2
and 6.1) up on a network drive. The 6.1 apps all work: I installed
the 6.1 runtime up on the network drive. However, on a number of PC's
the 6.0.2 apps don't work (their icons are generic, not LV) and give
forth the error messages "Labview error code 10: VI version (6.0) is
too old to convert to the current LV version (6.1)". Or: "Unable to
locate the Labview RunTime engine. XXX requires a version 6.0 (or
compatible) RunTime Engine."
By the way, 3 PC's that have some NI software on them do run the 6.0.2
network apps OK.
I accept the limitations. I would be willing to keep the 6.0.2 apps
in a separate network place if I could install the runtime for 6.0.2
up there as well. (
why not compile all to 6.1 you ask? .. because one
of them won't ... its front panel chokes with a load.cpp error).
My question: what are the files (and subdirs) needed from a 6.0.2
install to 'hand carry' so's to not need an install (and write the
registry) for any machine to use my EXE files? This used to be the
case before 6.1; one needed lvrt.dll and a few others, plus the
\models and the \Shared stuff.
Thanks

G'Day humenik,
I posted this article to the zone a while ago - it describes how to run *simple* exe's without having to install a run-time engine. This should work for different versions, as longs as you have to appropriate files with your exe's. This method definately works with 6.1 exe's.
http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=506500000008000000FB4D0000&UCATEGORY_0=_49_%24_6_&UCATEGORY_S=0
Like my Answer? Give it a Rating!
cheers,
Christopher
Christopher G. Relf
Certified LabVIEW Developer
[email protected]
Int'l Voicemail & Fax: +61 2 8080 8132
Aust Voicemail & Fax: (02) 8080 8132
EULA
1) This is a private email, and although the views expressed within it may not be purely
my own, unless specifically referenced I do not suggest they are necessarily associated with anyone else including, but not limited to, my employer(s).
2) This email has NOT been scanned for virii - attached file(s), if any, are provided as is. By copying, detaching and/or opening attached files, you agree to indemnify the sender of such responsibility.
3) Because e-mail can be altered electronically, the integrity of this communication cannot be guaranteed.
Copyright © 2004-2015 Christopher G. Relf. Some Rights Reserved. This posting is licensed under a Creative Commons Attribution 2.5 License.

Similar Messages

Each time I try to synch photos from my Windows 7 PC to my iPad2, iTunes stops working, and the error report says Problem Event Name:     APPCRASH   Application Name:     iTunes.exe   Application Version:     10.3.1.55   Application Timestamp:     4deec35

Each time I try to synch photos from my Windows7 PC to my iPad2, iTunes stops working and the error message is:
Problem Event Name:                          APPCRASH
Application Name:                             iTunes.exe
Application Version:                           10.3.1.55
Application Timestamp:                    4deec351
Fault Module Name:                          ntdll.dll
Fault Module Version:                        6.1.7601.17514
Fault Module Timestamp:                 4ce7ba58
Exception Code:                                  c0000005
Exception Offset:                                0002e3fb
OS Version:                                          6.1.7601.2.1.0.768.3
Locale ID:                                             1033
Additional Information 1:                  0a9e
Additional Information 2:                  0a9e372d3b4ad19135b953a78882e789
Additional Information 3:                  0a9e
Additional Information 4:                  0a9e372d3b4ad19135b953a78882e789
I reloaded iTunes 10 (64 bit) successfully, but the problem remains the same.
Any suggestions?

I looked in the folder from which I want to synch photos, but there is no such thing as an "ipod photo cache" in that folder, or sub-folders, as suggested in the link which you were nice enough to provide.
I have also tried removing photos from my iPad2 Photos App, and "iTunes has stopped working" shows up again as soon as I click on the "Synch photos from" button.

My itunes wont open and i cannot find an itunes .exe file

my itunes wont open and i cannot find an itunes .exe file

I have this same problem and when I go to the control panel to uninstall itunes, I can't do that either. I have been trying to uninstall so I can reinstall. Hopefully someone has an idea.

Report Generation Exe Error

Hello,
I am using LV 8.6.1 with the 1.13 report generation toolkit and I am having problems getting my built exe to work. I am trying to open an excel template and populate it with new data. I have broke the vi down to just opening excel - opening the template and then fill in some data. But at this point excel does not open at all. And naturally everything works fine in the development environment.
Error Code: -2147352573
Member not found in NI_ReportgenerationToolkit.lvlib:
Excel_open_workbook.vi
NI_Excel.lvclass: new reportsubvi.vi
I read a few help pages that said to add \vi.lib\utility\NIreport.llb and LVclass directories to the project folder and add them to the always include section of the build. But no luck so far.
Side question: The machine I want to use this on has 8.6.1 Full which does not have the extra excel functions that my developer has. Is there a way to install the DEV report generation toolkit in the full version? Then I would not need to build an exe.
UPDATE: I just tried the exe on a different machine that has a developer suite installed and it worked fine. So I guess I need to find out what else I need to add to the build to make it work.
Message Edited by _Bryan on 06-16-2010 11:58 AM
Solved!
Go to Solution.

There should be some info on this in the KB.
But first you should make sure that your version of the report generation toolkit actually supports excel 2000 (which is 10 years old)
That should be in the release notes of the toolkit
Ton
Free Code Capture Tool! Version 2.1.3 with comments, web-upload, back-save and snippets!
Nederlandse LabVIEW user groep www.lvug.nl
My LabVIEW Ideas
LabVIEW, programming like it should be!

Report Generation Toolkit error when running exe not vi

Unknown System Error in Get Report Settings.vi->Get Current Font.vi->Excel Easy Table (str).vi->insert table and save file.vi->80x test suite.vi
1. The above is an error I get from my exe
2. I do not get this error when just running the vi.
3. On several report gen functions cohersion dots are on my refnum input. Is this the cause of my problem with the exe?
I guess there is an another learning curve when dealing with the app builder.
Any suggestions would be appreciated.
Thanks
Brian
CLAD
Brian

forget what i wrote. it was my vi.
funny, most of the time it aint LabVIEW causing the problem but the program itself.
Brian

Report generation toolkit VI error when running EXE

A VI inside the Report Generation Toolkit (version 1.1.2), Excel Find Application Directory.vi, will not function correctly when running an EXE. The "Current VI's path" block will return the path of the currently running EXE rather than the path of the Excel Find Application Directory VI. (The same would be true for Word Find Application Directory.vi.)
-Joel
Solved!
Go to Solution.

Have you had a look at this knowledgebase article? The error is caused due to the exclusion of any dynamic VI.
Ipshita C.
National Instruments
Applications Engineer

How do I perform an Open VI Ref for a VI in my EXE?

Good evening,
I'm building a LV8.5 VI into an EXE using application builder. I am trying to get a reference to a SubVI using Open VI Reference. When I wire the subvi name as a string, I get an Error 1004 failure and the dialog says "the VI is not in memory".
I also tried the Open VI Reference by wiring a path that includes the EXE name prepended C:\MyApp\MyEXE.exe\MyVI.vi
When I tried this I got an Error 7 for File not Found
Does anyone know the proper way to include a SubVI in an EXE to be accessed later with Open VI Reference? I'm not certain if my VI that I'm loading dynamically was actually included in my EXE or if I'm providing the correct location for Open VI Reference.
Any advice or examples is appreciated. I'm using LV8.5 with the application builder.
Thanks,
Chris Norris
Embla Systems, Inc.

This definately sounds like you have not placed your vi into your executable. When you dynamically call a vi, it is not included automatically into the exe. You have to add it as a support file. There is a window in the exe builder where at the top left you select your "top level vi" then below that your "support vis" Make sure that the vi you are trying to call is included in the support vi list.
If you are always calling the same vi, even multiple times, there is a way to get the path without as much bother. Create a static reference to your vi. It is a little icon into which you place your vi on the diagram. Pull the reference from this, then use the properties vi to get the path. Open your vi reference using this path. Do not use the static reference to do things to the vi, as this can cause problems for you, especially if close the calling vi.
Good luck,
CyberTazer
Software Systems Engineer

LabView Exe Application file not launch Excel application for report generation

Dear All,
I created one LabVIEW application file for report generation (using Excel Template).
While I run the program in programming mode it works well and create the report file in the specified path.
After creation of the application file(exe), it gives the correct path of where the excel template is placed. The same path is given to New Report.vi, but it gives the error 'File Not Found'.
Tell me, is any other configuration required for generating Excel reports? (During exe application mode)
Give me the solution.
Thank You
Jegan.

Hello,
Most likely you are encountering a problem of stripping and/or building paths. Probably the easiest thing to do is put a couple indicators on your front panel for the path or paths you care about, build your exe, and make sure you are really using the path you'd like. If you always put the report at some deterministic place relative to the exe (that is, even it the exe is moved, it will go with the exe and remain in the same relative path location, then you can use the Current VIs Path funtion found in the ... File I/O -> File Constants palette as a start path (where you will want to strip at least the exe name off of course).
I think this will bring some clarity to the issue!
Best Regards,
JLS
Best,
JLS
Sixclear

Error while running sawserver.exe file

Hi All ,
I installed OBIEE 11.1.5 in my machine and Database is in different machine (For RCU) .OBIEE reports are working fine but, I tried to run sawserver.exe file to register new instanceconfig file to implement multiple rpds and Catalogs in OBIEE 11G by referring the below link.
http://rnm1978.wordpress.com/2009/08/25/multiple-rpds-on-one-server-part-2-presentation-services/
Command that I used is : sawserver.exe -c D:\Middleware\instances\instance1\config\OracleBIPresentationServicesComponent\coreapplication_obips1\instanceconfigdemo.xml
Am getting the Error : the procedure entry point long jmp count not be located in the dynamic link library orauts.dll
Thanks in Advance .

Hi,
How can i do it in OBIEE 11G? Any help will be grateful
Regards,
Joni

Error while deploying web role - Invalid application runtime - a runtime component is missing:/base/x64/IISConfigurator.exe

I have Azure SDK 2.5 installed and when I try and publish my web role from VS 2013, it fails. When I manually upload the package and config through the Azure Portal I get the error: "Invalid application runtime - a runtime component
is missing:/base/x64/IISConfigurator.exe".
I have tried uninstalling and re-installing the Azure SDK with no change in the error.
Any ideas how I can troubleshoot this?

I uninstalled the SDK, and tried to create a new cloud servce using the WCF service project template. The new project still gives me the same error:
The file provided is not a valid service package. Detailed error code: WCFServiceWebRole1 Invalid application runtime - a runtime component is missing:/base/x64/IISConfigurator.exe.

Rwbld60.exe error while calling a graph wizard from reports 6i.

Hi,
I have a latest patch 4f installed on my machine for reports 6i. When i call a graph wizard from my reports i am getting a program error saying "rwbld60.exe has generated errors".
How do i confirm that my new patch is installed successfully.
Thanks in adv.
Shailesh

I'm getting this also. I thought it was
due to my use of DATA PARAMETER. I've
logged TARS on this and have yet to hear
back from Oracle.
Maybe if enough of us get the error Oracle
will give some guidance on this one.

Error message when clicking on links from thunderbird: Firefox.exe – Entry Point Not found

When I click on any link in a Thunderbird email message I get the error message:
Firefox.exe – Entry Point Not found
The procedure entry point ?DllBlocklist_Initialize@@YAXXZ could not be located in the dynamic link library T:\PQligP sFuvy (X86)\pJPpSox HneiCFv\GwCMqTQ.Oqt.
I tried uninstalling Firefox 27 completely and reinstalling it, and the error is still there. When I uninstall V27 and install the older V26 the error disappears. Id there an issue with V27 trying to work with links from Thunderbird?
I am on a laptop running Windows 8.1 with all current downloads.

Thanks for the reply - as best as I can tell it seems to be some kind of incompatibility between Thunderbird V24.3.0 and Firefox V27. If I install Firefox V26 then everything works as it should. I haven't tried installing a previous version of Thunderbird to see if that makes a difference.

ITunes.exe Error Message

Grateful for any help advice out there.
I am unable to copy songs for iTunes 6 to my iPod video, even though there is plenty of space left on the iPod. I can upload music from CDs to iTunes, but when I attempt to transfer them to the iPod nothing happens, and I get the following message:
iTunes.exe - corrut file
\iPod_Control\iTunes\Temp File is corrupt and unreadable. Please run chkdsk utility.
I am not particularly IT literate and would appreciate any advice or assistance on what I should do.
Sony laptop Windows XP

compton anstey,
This article addresses the issue you are experiencing:
http://docs.info.apple.com/article.html?artnum=300554

With Windows Vista, the most recent Itunes update 1/30/2014 has caused Itunes not to work, with a Mscvr80.dll not found error. Uninstalled all Apple programs, and installed fresh Itunes. Same problem. Tried to reinstall using an older install exe nogo

Recent ITunes update has caused ITunes not to work. Tried uninstalling all Apple products and reinstalling fresh. Still doesn't work. Tried reinstalling from an old install.exe. Install went nicely but program won't start as it says it can't open the library file.

Now that I have no way of accessing any of the products I have purchased from ITunes, I will most certainly never use ITunes again for any reason. Why throw good money after bad? I will use another MP3 player that is not as cumbersome or proprietary.
Lesson learned.

\\SERVER\Clients\Setup\setup.exe with Windows Vista Error

I added the first Vista client to an SBS 2003, SP1 domain. Until now, all clients were WinXP, SP2. Office 2003 is installed on the XP clients, and the Vista client, which may not be pertinent to this problem.
As is normal, "\\SERVER\Clients\Setup\setup.exe /s SERVER" is executed when a user logs on to any domain client. On the Vista client, I always get the dialog -- regardless of the account privilege -- asking for permission to run Setup.exe. It is annoying. Occasionally, the Program Compatiblity Assistant will appear and advise there's a known compatiblity issue with Setup.exe. It points to KB article 926505 for resolution. The title of the KB is, "Windows Small Business Server 2003: Windows Vista and Outlook 2007 compatibility update."
When I run the SBS2003SP1-KB926505-X86-ENU.EXE fix, I get the error: "This update cannot be installed. Either it is already installed as part of an existing service pack, or it requires a more recent service pack. For more information, see the systems requirements on the download page."
I installed Windows Server 2003 SP2 and run the KB926505 fix, but I get the same error "This update cannot be installed. Either it is already installed as part of an existing service pack" After a reboot of te SBS server the same problem on the Vista client, I always get the dialog -- regardless of the account privilege -- asking for permission to run Setup.exe. It is annoying. Occasionally, the Program Compatiblity Assistant will appear and advise there's a known compatiblity issue with Setup.exe. It points to KB article 926505 for resolution.
The problem is Windows Vista Business, because all windows XP clients have no problem at all.

PNP,
You do not say whether if you accept the permission dialog whether the setup continues or not, but the short answer to the question revolves around UAC.
Remember that EVERY user (except the actual Administrator account) has only Standard user rights regardless of group. When a task that requires Admin rights is executed, one of three things will happen: 1) If you are THE Administrator, then your task will continue. 2) If you have Admin rights, you will be prompted that a process is trying to use elevated rights and ask for permission, or 3) If you are a Standard user, you will either be denied flatly or prompted to supply credentials. Which of these happen depend on GPO settings, but the default is to prompt.
In any event, I believe that this is what you are running into, and is one of the big feature improvements in Vista. Yes, it can be a bit annoying (Try deleting an "All Users" icon from the Start Menu!) but is there to place one more barrier between virus and malware writers and your OS.
If it's TOO annoying to bear, you can turn off UAC by going into your profile and disabling it. (It requires Admin rights, of course. ) It is not recommended as you do a very effective job or nutering the Vista Security Model by doing so.
If it, of course, your choice. we IT Admins have a lot more issues with this than the standard user, but for me, I gladly take the tradeoff because I worry a lot less about those few I HAVE to give Admin rights to.
Good luck!

Error report on win 8.1 about conhost.exe and werfault.exe

I am not sure exactly what is happening, but I have noticed recently a new problem with CONHOST.EXE and werfault.exe each time I was opened application. and I didn't know exactly about was there have relationship with my brightness control
(increase or decrease) than I can't make any change after first time I have noticed about conhost.exe and werfault.exe. and other problem than my laptop more 'slowly' than before, but the console window will remain open fastly enough. (The host process
exists, but I can see an orphaned CONHOST.EXE for the application in Task Manager.)
I hope someone who sees this knows why this is happening, and can help me fix the problem.
Thanks!

Hi,
Here is the details about conhost.exe process:
Windows 7 / Windows Server 2008 R2: Console Host
http://blogs.technet.com/b/askperf/archive/2009/10/05/windows-7-windows-server-2008-r2-console-host.aspx
Same within Windows 8.
The werfault.exe is used for Windows Error Reporting.
You can go to event viewer to check if there are any error messages.
For this kind of issue, you may also try Clean Boot to see if this problem persists.
Alex Zhao
TechNet Community Support

6.0.2 exe .vs. 6.1 exe

Similar Messages

Maybe you are looking for