6.3.5 upgrade to 7.2.2 cant connect over remote VPN client

The device is a PIX 525 UR with v. 7.2.2 installed over 6.3.5. I have deleted all previous VPN setups and re-installed the remote vpn and client software multiple times and the VPN times out during securing the channel and comes back with a error: 412 the local client has disconnected the session. I have been using the ASDM VPN wizard to configure the VPN and upon submitting the config I recieve a warning saying the tunnel-group does not exist but then when I exit it shows up in the tunnel group and is listed in the CLI. Also in the debug logs iget the error: 3713902 Group = Eisenhower, IP = 166.214.197.X, Removing peer from peer table failed, no match!
I would appreicate any assisance with this attached is the relevent configuration.
Thanks,
Scott r

This document describes how to use the Cisco Adaptive Security Device Manager (ASDM) to configure authentication and authorization server groups on the Cisco PIX 500 Series Security Appliance. In this example, the server groups created are used by the policy of a VPN tunnel group to authenticate and authorize incoming users.
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a008060f261.shtml

Similar Messages

Since I upgraded to Lion, my RSA securid token and Cisco VPN client doesn't work any longer. Anyone have suggestions on how to fix that?

Since upgrading to Lion, I can no longer use VPN because my RSA securid token and CIsco VPN Client won't load. Any suggestioins out there?

.

Upgrade to iTunes 7.2 broke connection with remote speakers

There have been a few discussions about the inability of iTunes to connect to remote speakers in the past, and I found one that was answered regarding an upgrade to 7.0 back in September 2006 - b noir recommended the help article posted on his page: http://docs.info.apple.com/article.html?artnum=304371
My issue is the same as the one posted in Sept. 2006, but it only started when I downloaded the upgrade to iTunes 7.2. I see the remote speakers greyed out in my iTunes speaker list but can't select them. The fix in the help article above of configuring IPv6 doesn't help. Has anyone else run into this/have any suggestions for me? My wireless network consists of 2 Airport Expresses; the extension is the one hooked up to my speakers.
Many, many thanks!

I'm experiencing something similar where my remote speakers are working well from my Macs (wired) and Windows Vista laptop (wireless) but do not show up at all from my Windows XP desktop (wired).
I do have Symantec Personal Firewall running, but I have (1) trusted my local internal network, (2) explicitly opened ports 3689 and 5353 and (3) tried it with the firewall disabled with no luck. I do not have Windows Firewall running, and I don't believe I have anything else that would be limiting network traffic. I do not have Bonjour or Rendevous services running. I can ping the AEs just fine (I have 3 AEs), and I am on the same subnet. I have selected LOOK FOR REMOTE SPEAKERS in the iTunes settings, and I am running the latest version of iTunes (7.2). I have also not tried downgraded to an earlier version of iTunes, but for now I'd rather get this fixed in another fashion as 7.2 works well from my other machines.
I hope the above description (with fixes recommended by other users in other threads) is helpful. I appreciate any input or feedback people may have.

Upgrading to 10.0.1 lost connection to remote speakers on Airport Express

after upgrading iTunes 10 to 10.0.1 the name of my airtunes speakers connected to Airport express (Firmware 7.4.1)is visible in iTunes but won't play music (error -15000).
Same observation in two of my PC (Windows 7) laptop/Netbooks.

Solved the problem. Uninstalled iTunes completely. Restarted. Reinstalled iTunes 10.0.1. Said allow to the firewall setting changes. Done. Connection to remote speaker regained.

Windows VPN clients can't use network servers after 10.5.1 upgrade

We have two Xserves, both formerly running 10.4.11. One is the OD master, the other a replica. The replica is also the VPN server, and is a DHCP server for the small number of IP addresses reserved for VPN clients.
The OD master upgrade went fine. I completely reinstalled the OD replica, set the replica up again, and set up the VPN server. It supports L2TP/IPsec connections only.
After the upgrade, Mac users running Tiger or Leopard can connect to the VPN server and connect to network services without any problems. Windows users can connect, but cannot actually USE anything on my office network. For example, if you try to connect to a web server either by fully qualified domain name or by hostname, the connection from the browser simply times out.
In the Windows command line I can verify that I have an active connection by pinging and using the tracert command (equivalent of traceroute on UNIX). Hostname resolution works, too. But nothing happens when you try to open a web browser, which is mostly what my users need to do.
It doesn't matter whether you're logging in with an OD user account or a local account defined solely on the VPN server. Same behavior in Windows.
I had to take an older XServe running 10.4.11 out of our data center, move it to the office, and set it up on the same external network connection. 10.4.11 server works, 10.5.1 doesn't, from the same Windows client, set up exactly the same way.
I've been through the hoops with Apple Enterprise support, who now tell me that Engineering kicked it back to them and told them they'd charge me $695 to get it fixed, because it's ostensibly custom configuration work. If that's true, why is Windows XP listed under L2TP/IPSec support on page 127 of the Leopard Network Services Admin guide? I don't want a custom fix, I just want it to work the way it's supposed to work. Or I want Apple to retract the claim that OS X Server is the best workgroup server solution for Macs and Windows.
Anyone else encounter this problem or know of a fix?

Had the same problems, started after i tried out the firewall in Leopard server.
Seems that not all settings are reset even after turning the firewall off.
To reset the firewall to its default setting:
1 Disconnect the server from the Internet.
2 Restart the server in single-user mode by holding down the Command-s keys during
startup.
3 Remove or rename the address groups file found at /etc/ipfilter/
ipaddressgroups.plist.
4 Remove or rename the ipfw configuration file found at /etc/ipfilter/ipfw.conf.
5 Force-flush the firewall rules by entering the following in Terminal:
$ ipfw -f flush
6 Edit the /etc/hostconfig file and set IPFILTER=-YES-.
7 Complete the startup sequence in the login window by entering exit:
The computer starts up with the default firewall rules and firewall enabled. Use Server
Admin to refine the firewall configuration.
8 Log in to your server’s local administrator account to confirm that the firewall is
restored to its default configuration.
9 Reconnect your host to the Internet.
This solved the problem for me...

HT1937 i unlocked my iphone 4 factory and i upgrade to 6.1 when i connect it to itunes it apears The SIM card inserted in this iPhone does not appear to be supported This iPhone is not currently setup to work with carrier you're attempting to use. Please

i unlocked my iphone 4 factory and i upgrade to 6.1 when i connect it to itunes it apears
The SIM card inserted in this iPhone does not appear to be supported
This iPhone is not currently setup to work with carrier you're attempting to use. Please insert another SIM card from a supported carrier or request that this iPhone be unlocked.

It sounds like you or someone else hacked the phone to unlock it. Updating it locked it to the original carrier.
How did you unlock it? The ONLY legitimate way is to ask the carrier it is locked to to unlock it. Any other way requires hacking or jailbreaking the phone.

After upgrading to itunes 10.5, and connecting ipad 2, message appears " IPAD cannot be used it requires itunes 10.5 or later. Go to itunes store and download the latest version." I am windows xp user.

After upgrading to Itunes 10.5 and connecting the IPAD. I get a following message. How do I resolve this issue. There is no other way to download itunes to ipad other than the itunes on your computer or laptop. I am a windows xp user.

Dear Mr. Sawyer,
To my surprise, the version is shown as 10.0.1.22. I will uninstall itunes and try loading the same again. After uninstalling do we need to delete any registry entries for Windows XP.
Thanks for your response and concern.
Regards
Amit Samel

Since upgrading to Mountain Lion I cannot connect to my wireless router

Since upgrading to Mountain Lion I cannot connect to my wireless router. I have 2 wireless networks in my home. One is the primary whuch all of my devices connect to. The other is for backup only. I cannot connect to the primary with my iMac but have no trouble with any of the other devices which include iphones and ipads.phones and iPads. I can however connect to the backup without a problem. I have tried upgrading the firmware of the router as well as changing the security from WEP to WPA-2, no luck. Can anyone help?

Try this, it's for information.
In Finder, open the Go menu, press and hold the option key, 'Library' will appear on the menu, click and scroll to Application Support, open the folder and scroll to 'AddressBook-v22.abcddb'. Click on the file and press Command-I. Towards the bottom you'll see Permissions, tell me what they are please.

Does anyone know how to get my email to download pictures? I was able to view pictures in my email before I upgraded to iOS 7. I have allow remote pictures turned on in my settings.

I was able to view pictures in my email before I upgraded to iOS 7. I have allow remote pictures turned on in my settings. I loved Apple until this last upgrade. It used to be an intuitively designed product. I hate it now. If they don't make it easier for older users to use again, this will be the last Apple product I every purchase.

Welcome to AD!
I have a regular post for the top 3 or 4 fixes for that 9808 error. Obviously you are going to skip #1, since you've already tried it. Let me know how you get on with the next 2.
The top 3 fixes to itunes error 9808 seem to be
1) Go to Start > Control Panel > Internet Options > Advanced, make sure that SSL 3.0 is checked and TLS 1.0 is checked. Also under Security make sure that the “Check for server certificate revocation (requires restart)” is unchecked. Then click ok and fire up iTunes.
2) The culprit was Norton. The users are set up as Admin and Standard. I have Parental Controls turned on in both Vista as well as Norton. Admin users had no problems connecting to iTunes. Standard users would get the error. I had to go to Norton’s Personal Firewall and add the program “iTunes Helper.exe” and set the option to “Allowed” (”iTunes.exe should already be in the Allowed category.) in order for the standard users to be able to connect.
3) close iTunes if you have it open right now. Then go to C:/Documents and Settings/username/Local Settings/Application Data/Apple Computer/iTunes. Delete or cut the preferences.xml file which contains your iTunes preferences. Then go to C:/Documents and Settings/username/Application Data/Apple Computer/iTunes and delete or move the preferences.xml file. For Mac users, there is only one file you must delete or move a to a new location and is located at User > Library > Preferences > com.apple.itunes.plist. Restart iTunes and it will recreate those two (or one) files with the default settings. Feel free to set your preferences back to what they were and then connect to the iTunes store and enjoy!
And #4, see if you can get into the iTS from a different windows admin account on the same PC.

HT202157 After the upgrade, my Apple TV pretends to connect the HDMI to a USB connector...

After the upgrade, my Apple TV pretends to connect the HDMI to a USB connector...

Thanks !!!
I didn't notice that there is a micro usb connector in the back of the Apple TV.
I thought according to the message in the screen of the Apple, it was a connection between the HDMI and a computer with USB an iTunes.
My next step if to find a USB to MICRO USB cable...

VPN Client Issue after Vista Upgrade

Not sure if this should be posted here, if not please let me know.
My organization has recently implemented Vista via an Upgrade-in-Place Process that takes an imaged system (Windows XP Pro - 32bit) and upgrades the system with a network image of Windows Vista Enterprise. Applications are left installed and herein lies my problem.
I'm using Cisco VPN Client 5.0.04, the client worked fine before the upgrade, after the upgrade, not so well.
While troubleshooting I noted the Cisco Systems VPN Adapter was no longer listed as being installed under Network Adapters in the Windows Device Manager, there was however an adapter, labled 6to4 adapter with an exclamation point. I went through the uninstall process for the Cisco VPN Client, rebooted and reinstalled. When trying to connect, I can use one of two pcf files (both are a back up of one another), the first connection profile goes through the motion of connection, tries to contact the security gateway, and states "Not Connected"
I enabled logging on the connection and tried again. Here's an excerpt from that log:
09:37:18.278 04/21/09 Sev=Warning/2 CERT/0xA3600038
Successfully added Key Usage fields to be matched.
7 09:37:19.792 04/21/09 Sev=Warning/2 CERT/0xA3600038
Successfully added Key Usage fields to be matched.
8 09:37:20.338 04/21/09 Sev=Warning/2 CERT/0xE3600001
Failed to launch application using cert pipe due to error: 0x800b010a.
9 09:37:20.338 04/21/09 Sev=Warning/2 IKE/0xE300009B
Failed to generate signature: Signature generation failed (SigUtil:97)
10 09:37:20.338 04/21/09 Sev=Warning/2 IKE/0xE300009B
Failed to build Signature payload (MsgHandlerMM:489)
11 09:37:20.338 04/21/09 Sev=Warning/2 IKE/0xE300009B
Failed to build MM msg5 (NavigatorMM:312)
12 09:37:20.338 04/21/09 Sev=Warning/2 IKE/0xE30000A7
Unexpected SW error occurred while processing Identity Protection (Main Mode) negotiator:(Navigator:2263)
Has anyone seen this behavior after an upgrade from XP to Vista? I'm I going to have to start with a fresh install? I appreciate any suggestions or advice.
Thanks,
Jimi

I finally figured out this problem and I feel it should at least be shared for another person who runs into this problem.
The problem was resolved by loading my personal certificates (the one that is read by the smart card reader and used to authenticate me on VPN) needed to be added to the personal certificates folder in the Local Machine layer.
I did this by opening up an MMC window --> Adding the certificates snap-in (in windows 7 it distinguishes 3 different layers, so choose the local user and the computer layer) --> and then copying the certificates in the personal folder located under Certificates - Current User into the personal folder located in Local Machine.
The most likely reason this happened to me is that the image I was working with had security settings blocking the certificates to be read at the current user level and not at the local machine level. Therefore, it's a problem with out image and the security policies put in place at the registry level and/or group policies placed in Active Directory. This is more of a workaround than an actual fix to the problem, but at least it pinpoints where the break is happening.
Now I can push the image back to the developers to review the security policies placed in the image.

Upgraded to Maverick. Now cannot connect to wifi. All my other devices will connect. Have rest wireless hot spot switch and cable modem. Other devices still connect but MacPro does not. MacPro wireless is self assigning an IP address blocking access.

Upgraded to Maverick. Now cannot connect to wifi. All my other devices will connect. Have rest wireless hot spot switch and cable modem. Other devices still connect but MacPro does not. MacPro wireless is self assigning an IP address blocking access. It will connect if I connect to my iPhone hot spot via wifi. Any ideas?

If you follow this video you'll see how to delete your WiFi AP from the OS, this will allow you to select it again which I feel will correct your problem.
https://app.box.com/s/fe7v7h7kywjr23spumqp

Hi, after upgrading to 5.1 I cant use my ethernet cable any more

Hi, after upgrading to 5.1 I cant use my ethernet cable any more for air play or photostream. If I use Wifi instead it works!. Seems like a bug in 5.1. Anyone with similar issue?

FIxed my problem!
Go to System preferences
Go to Ethernet
Go to Advance
Go to Hardware
The just make the changes like in the pictures below
it work for me

Cant connect Proxy settings keep resetting on exit since upgrade

Ever since I upgraded to 4.whatever it is now every time I close firefox when I start it up again I cant connect because it changes my proxy connection to manual proxy configuration despite that I dont use a proxy. I can change it to whichever of the other options and it works fine until I close then reverts back.
It is very annoying is there anyway to fix this so it saves my settings?

Disabling the extension (add-on) FireShot did it for me =)

Can I upgrade mac OS 10.7 to 10.8 remotely through ARD?

Can I upgrade mac OS 10.7 to 10.8 remotely through ARD?

Yes. Sort of.
Using ARD, you can copy an Install Mac OS X.app to the target machine. Then launch the application and start the installation process. At this point, the machine will "go dark" and will eventually reappear in ARD once the installation is complete.

6.3.5 upgrade to 7.2.2 cant connect over remote VPN client

Similar Messages

Maybe you are looking for