6.40 Ramp-Up: Dispatcher problem
Hi,
we have installed the WAS 6.40 unicode version (ABAP + Java) and Adobe Document Services as part of the Ramp Up.
The installation was done successfully without any problems and Support Packages (ABAP, BASIS) have been applied up to level 3, in addition the ABAP kernel has been upgraded to patch level 19.
We have the following issues:
1. In the Microsoft Management Console the disp+work
(dispatcher) process is in yellow status: "Running but dialog queue info unavailable" even though we can logon to the system through the GUI and do not see any error messages in the system.
2. When we try to test print any Adobe Form through transaction code "SFP", we get the following error message:
"Test for function group /1BCDWB/SM00000001 Function module /1BCDWB/SM00000001
Runtime: 7,670,791 Microseconds
Exception SYSTEM_ERROR
Message ID: FPRUNX Message number: 001
Message: Adobe document services error: SOAP Runtime Exception CSoapExceptionTransport : (1001)
3. The trace file in the ICM Monitor ("SMICM") shows the following error messages:
[Thr 4636] *** INFO => the EXTBIND attribute in parameter
icm_server_port_<xx> for service 8000 is not necessary on Windows - i
[Thr 4636] Tue Jul 27 17:58:19 2004
[Thr 4636] *** WARNING => IcmNetCheck: NiAddrToHost(10.0.0.1) took 11 seconds [icxxtool.c 431]
[Thr 4636] *** WARNING => IcmNetCheck: 1 possible network problems detected - please check the network/DNS settings [icxxtool.c
[Thr 3940] Tue Jul 27 17:58:28 2004
[Thr 3940] IcmJ2EEScheduleFunc: WARNING: no HTTP service defined
[Thr 4896] Tue Jul 27 18:02:02 2004
[Thr 4896] *** ERROR => IcmCreateCacheInvalMsg: no HTTP/HTTPS service active [icxxmsg.c 2903]
[Thr 4896] *** ERROR => IcmCreateCacheInvalMsg: no HTTP/HTTPS service active [icxxmsg.c 2903]
[Thr 4896] *** ERROR => IcmCreateCacheInvalMsg: no HTTP/HTTPS service active [icxxmsg.c 2903]
We also posted this as a Ramp-Up OSS message but maybe someone on this forum came across this as well before...
Thanks,
Guenther
Message was edited by: Guenther Schober
Message was edited by: Guenther Schober
To resolve step 3, remove the EXTBIND=1 parameter from the instance profile. EXTBIND is only needed when using ports < 1024.
Similar Messages
-
Hi
I have ECC6 IDES version was working fine last 3 months . i have just added two profiles in RZ10
login/accept_sso2_ticket = 1
login/create_sso2_ticket = 2
it was not reflecting on so i thought i will restart server so i did it. since then my server is always in yellow state. my Abap , J2ee table are blank and i monitored couple of time when i start server first all table start in RUN state then Ended and disappears then dispatcher goes stopped.
Things i did to resolve this but didn't work
1) tryed to revert back old profiles in OS level
2) Increases j2ee time out ( 600 to 6000)
3) started data base at command level using connect/@ PIS as sydba and the mounted database and then started management consol but still same problem continues.
Can some one help me quickly ...
trc file: "dev_w0", trc level: 1, release: "700"
M
M Tue Sep 25 11:14:07 2012
M calling db_connect ...
C Prepending D:\usr\sap\PIS\DVEBMGS40\exe to Path.
C Client NLS settings: AMERICAN_AMERICA.UTF8
C Logon as OPS$-user to get SAPSR3's password
C Connecting as /@PIS on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 00000000130F28C0 000000000A7B33C0 000000000A7B8BE8
C Attaching to DB Server PIS (con_hdl=0,svchp=000000000A7B8AA8,svrhp=0000000013111918)
C Starting user session (con_hdl=0,svchp=000000000A7B8AA8,srvhp=0000000013111918,usrhp=000000000A7B3BD8)
C Now '/@PIS' is connected (con_hdl 0, nls_hdl 0).
C Got SAPSR3's password from OPS$-user
C Disconnecting from connection 0 ...
C Closing user session (con_hdl=0,svchp=000000000A7B8AA8,usrhp=000000000A7B3BD8)
C Now I'm disconnected from ORACLE
C Connecting as SAPSR3/<pwd>@PIS on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
C Nls CharacterSet NationalCharSet C EnvHp ErrHp ErrHpBatch
C 0 UTF8 1 00000000130F28C0 000000000A7B33C0 000000000A7B8BE8
C Starting user session (con_hdl=0,svchp=000000000A7B8AA8,srvhp=0000000013111918,usrhp=000000000A7B3BD8)
C Now 'SAPSR3/<pwd>@PIS' is connected (con_hdl 0, nls_hdl 0).
C Database NLS settings: AMERICAN_AMERICA.UTF8
C Database instance PIS is running on DEVSYS with ORACLE version 10.2.0.1.0 since 20120924
B Connection 0 opened (DBSL handle 0)
B Wp Hdl ConName ConId ConState TX PRM RCT TIM MAX OPT Date Time DBHost
B 000 000 R/3 000000000 ACTIVE NO YES NO 000 255 255 20120925 111407 DEVSYS
M db_connect o.k.
M ICT: exclude compression: .zip,.cs,.rar,.arj,.z,.gz,.tar,.lzh,.cab,.hqx,.ace,.jar,.ear,.war,.css,.pdf,.js,.gzip,.uue,.bz2,.iso,.sda,.sar,.gif
I MtxInit: 0 0 0
M SHM_PRES_BUF (addr: 0000000014E30050, size: 4400000)
M SHM_ROLL_AREA (addr: 000007FFE6D00050, size: 268435456)
M SHM_PAGING_AREA (addr: 0000000015270050, size: 134217728)
M SHM_ROLL_ADM (addr: 000000001D280050, size: 2678942)
M SHM_PAGING_ADM (addr: 000000001D510050, size: 525344)
M ThCreateNoBuffer allocated 544152 bytes for 1000 entries at 000000001D5A0050
M ThCreateNoBuffer index size: 3000 elems
M ThCreateVBAdm allocated 12176 bytes (50 server) at 000000000FFD0050
X EmInit: MmSetImplementation( 2 ).
X MM diagnostic options set: 0
X <ES> client 0 initializing ....
X Using implementation flat
X ES initialized.
B db_con_shm_ini: WP_ID = 0, WP_CNT = 13, CON_ID = -1
B
B Tue Sep 25 11:14:08 2012
B dbtbxbuf: Buffer TABL (addr: 0000000022E40160, size: 30000000, end: 0000000024ADC4E0)
B dbtbxbuf: Profile: max_objects = 5000, displace = 1, reorg = 1
B dbtbxbuf: request_unit = 2000, sync_reload = 5, inval_reload = 5
B dbtbxbuf: protect_shm = 0, force_checks = 0
B dbtbxbuf: tsize_retry = 14206976
B ***LOG BB0=> buffer TABL started with length 30000000 bytes [dbtbxbuf#2 @ 16178] [dbtbxbuf1617 8]
B dbtbxbuf: Buffer TABLP (addr: 0000000024AE0160, size: 10240000, end: 00000000254A4160)
B dbtbxbuf: Profile: max_objects = 500, displace = 1, reorg = 1
B dbtbxbuf: request_unit = 2000, sync_reload = 5, inval_reload = 5
B dbtbxbuf: protect_shm = 0, force_checks = 0
B dbtbxbuf: tsize_retry = 5032704
B ***LOG BB0=> buffer TABLP started with length 10240000 bytes [dbtbxbuf#2 @ 16178] [dbtbxbuf1617 8]
B dbtbxbuf: Reading TBX statistics:
B dbtbxbuf: 0 object entries precreated
B Layout of EIBUF buffer shared memory:
B 0: 1 * 4 = 4
B 1: 1 * 400 = 400
B 2: 13 * 40 = 520
B 3: 4001 * 48 = 192048
B 4: 2000 * 256 = 512000
B 5: 4001 * 8 = 32008
B 6: 1 * 200 = 200
B 7: 65 * 8 = 520
B 8: 13502 * 256 = 3456512
B Tracing = 0, Shm Protection = 0, Force checks = 0
B dbexpbuf: Buffer EIBUF (addr: 00000000254B0170, size: 4194304, end: 00000000258B0170)
B ***LOG BB0=> buffer EIBUF started with length 4096k bytes [dbexpbuf#1 @ 2322] [dbexpbuf2322 ]
B Layout of ESM buffer shared memory:
B 0: 1 * 4 = 4
B 1: 1 * 400 = 400
B 2: 13 * 40 = 520
B 3: 4001 * 48 = 192048
B 4: 2000 * 256 = 512000
B 5: 4001 * 8 = 32008
B 6: 1 * 200 = 200
B 7: 65 * 8 = 520
B 8: 13502 * 256 = 3456512
B Tracing = 0, Shm Protection = 0, Force checks = 0
B dbexpbuf: Buffer ESM (addr: 00000000258C0170, size: 4194304, end: 0000000025CC0170)
B ***LOG BB0=> buffer ESM started with length 4096k bytes [dbexpbuf#1 @ 2322] [dbexpbuf2322 ]
B Layout of CUA buffer shared memory:
B 0: 1 * 4 = 4
B 1: 1 * 400 = 400
B 2: 13 * 40 = 520
B 3: 3001 * 48 = 144048
B 4: 1500 * 256 = 384000
B 5: 3001 * 8 = 24008
B 6: 1 * 200 = 200
B 7: 193 * 8 = 1544
B 8: 4916 * 512 = 2516992
B Tracing = 0, Shm Protection = 0, Force checks = 0
B dbexpbuf: Buffer CUA (addr: 0000000025CD0170, size: 3072000, end: 0000000025FBE170)
B ***LOG BB0=> buffer CUA started with length 3000k bytes [dbexpbuf#1 @ 2322] [dbexpbuf2322 ]
B Layout of OTR buffer shared memory:
B 0: 1 * 4 = 4
B 1: 1 * 400 = 400
B 2: 13 * 40 = 520
B 3: 4001 * 48 = 192048
B 4: 2000 * 256 = 512000
B 5: 4001 * 8 = 32008
B 6: 1 * 200 = 200
B 7: 81 * 8 = 648
B 8: 13501 * 256 = 3456256
B Tracing = 0, Shm Protection = 0, Force checks = 0
B dbexpbuf: Buffer OTR (addr: 0000000025FC0170, size: 4194304, end: 00000000263C0170)
B ***LOG BB0=> buffer OTR started with length 4096k bytes [dbexpbuf#1 @ 2322] [dbexpbuf2322 ]
B ***LOG BB0=> buffer CALE started with length 500000 bytes [dbcalbuf#1 @ 2206] [dbcalbuf2206 ]
B dbtran INFO (init_connection '<DEFAULT>' [ORACLE:700.08]):
B max_blocking_factor = 15, max_in_blocking_factor = 5,
B min_blocking_factor = 10, min_in_blocking_factor = 5,
B prefer_union_all = 0, prefer_join = 0,
B prefer_fix_blocking = 0, prefer_in_itab_opt = 1,
B convert AVG = 0, alias table FUPD = 0,
B escape_as_literal = 1, opt GE LE to BETWEEN = 0,
B select * =0x0f, character encoding = STD / <none>:-,
B use_hints = abap->1, dbif->0x1, upto->2147483647, rule_in->0,
B rule_fae->0, concat_fae->0, concat_fae_or->0
M SecAudit(RsauInit): Start init of Security Audit Log for first wp.
M SecAudit(RsauCreateShm): New block for Security Audit Log allocated in SCSA
M SecAudit(RsauCreateShm): SCSA memory usage: SecAudit = 1160, total = 3064
M SecAudit(RsauShmInit): SCSA size................ = 4096
M SecAudit(RsauShmInit): addr of SCSA............. = 000000000AAF0050
M SecAudit(RsauShmInit): addr of RSAUSHM.......... = 000000000AAF07C0
M SecAudit(RsauShmInit): addr of RSAUSLOTINFO..... = 000000000AAF0800
M SecAudit(RsauShmInit): addr of RSAUSLOTS........ = 000000000AAF080C
M SecAudit(RsauShmInit): SHM version.............. = 5
M SecAudit(RsauShmInit): SHM Slot version......... = 2
M SecAudit(RsauShmInit): RSAU active.............. = 0
M SecAudit(RsauShmInit): number of slots possible. = 10
M SecAudit(RsauShmInit): number of slots requested = 2
M SecAudit(RsauShmInit): number of slots used..... = 2
M SecAudit(RsauShmInit): user selection........... = 0
M SecAudit(RsauShmInit): max size of one file..... = 0 KB
M SecAudit(RsauShmInit): max size of all files.... = 102400 KB
M SecAudit(RsauGetCurrentProfile): Init of shared memory completed
M SecAudit(RsauGetCurrentProfile): Security Audit Log not active
M SsfSapSecin: automatic application server initialization for SAPSECULIB
N SsfSapSecin: Looking for PSE in database
N SsfPseLoad: started...(path=D:\usr\sap\PIS\DVEBMGS40\sec, AS=devsys, instanceid=40)
N SsfPseLoad: Downloading file D:\usr\sap\PIS\DVEBMGS40\sec (client: , key: 102635, len: 14851)
N SsfPseLoadFile: Couldn't open file D:\usr\sap\PIS\DVEBMGS40\sec: Permission denied
N SsfPseLoad: Downloading file D:\usr\sap\PIS\DVEBMGS40\sec\SAPELEARN200.pse (client: , key: 172011, len: 1348)
N SsfPseLoad: Downloading file D:\usr\sap\PIS\DVEBMGS40\sec\SAPSNCS.pse (client: , key: 025318, len: 804)
N SsfPseLoad: Downloading file D:\usr\sap\PIS\DVEBMGS40\sec\SAPSSLA.pse (client: , key: 025401, len: 2838)
N SsfPseLoad: Downloading file D:\usr\sap\PIS\DVEBMGS40\sec\SAPSSLC.pse (client: , key: 025427, len: 3080)
N SsfPseLoad: Downloading file D:\usr\sap\PIS\DVEBMGS40\sec\SAPSSLS.pse (client: , key: 025344, len: 1465)
N SsfPseLoad: Downloading file D:\usr\sap\PIS\DVEBMGS40\sec\SAPSYS.pse (client: , key: SYSPSE, len: 14851)
N SsfPseLoad: ended (6 of 7 sucessfully loaded, 8 checked...
N MskiCreateLogonTicketCache: Logon Ticket cache created in shared memory.
N MskiCreateLogonTicketCache: Logon Ticket cache pointer registered in shared memory.
M rdisp/reinitialize_code_page -> 0
M icm/accept_remote_trace_level -> 0
M rdisp/no_hooks_for_sqlbreak -> 0
N SncInit(): Initializing Secure Network Communication (SNC)
N PC with Windows NT (mt,ascii,SAP_UC/size_t/void* = 16/64/64)
N SncInit(): found snc/data_protection/max=3, using 3 (Privacy Level)
N SncInit(): found snc/data_protection/min=2, using 2 (Integrity Level)
N SncInit(): found snc/data_protection/use=9, using 3 (Privacy Level)
N SncInit(): found snc/gssapi_lib=path_to_SAPCRYPTOLIB
M *** ERROR => DlLoadLib: LoadLibrary(path_to_SAPCRYPTOLIB) Error 126 [dlnt.c 237]
M Error 126 = "The specified module could not be found."
N *** ERROR => SncPDLInit(): DlLoadLib("path_to_SAPCRYPTOLIB")=DLENOACCESS
N [sncxxdl.0340]*** ERROR => SncPDLInit()==SNCERR_INIT, Adapter (#0) path_to_SAPCRYPTOLIB not loaded
N [sncxxdl.0604]<<- SncInit()==SNCERR_INIT
N sec_avail = "false"
M ***LOG R19=> ThSncInit, SncInitU ( SNC-000001) [thxxsnc.c 230]
M *** ERROR => ThSncInit: SncInitU (SNCERR_INIT) [thxxsnc.c 232]
M in_ThErrHandle: 1
M *** ERROR => SncInitU (step 1, th_errno 44, action 3, level 1) [thxxhead.c 10019]
M
M Info for wp 0
M
M stat = 4
M reqtype = 1
M act_reqtype = -1
M rq_info = 0
M tid = -1
M mode = 255
M len = -1
M rq_id = 65535
M rq_source = 255
M last_tid = 0
M last_mode = 0
M semaphore = 0
M act_cs_count = 0
M control_flag = 0
M int_checked_resource(RFC) = 0
M ext_checked_resource(RFC) = 0
M int_checked_resource(HTTP) = 0
M ext_checked_resource(HTTP) = 0
M report = > <
M action = 0
M tab_name = > <
M vm = V-1
M PfStatDisconnect: disconnect statistics
M Entering TH_CALLHOOKS
M ThCallHooks: call hook >SAP-Trace buffer write< for event BEFORE_DUMP
M TrThHookFunc: called for WP dump
M ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
M *** ERROR => ThrSaveSPAFields: no valid thr_wpadm [thxxrun1.c 720]
M *** ERROR => ThCallHooks: event handler ThrSaveSPAFields for event BEFORE_DUMP failed [thxxtool3.c 260]
M Entering ThSetStatError
M ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)
M Entering ThReadDetachMode
M call ThrShutDown (1)...
M ***LOG Q02=> wp_halt, WPStop (Workproc 0 1680) [dpnttool.c 327]
Regards
BabuProblem solve by taking out SNC profile
-
Urgent, creating xml files dynamically, request dispatcher problem
hi all,
Problem 1:
There is a problem we are facing, while request dispatching.
The files CBECBC.XML & CBECBC_Envelop.XML,
both xml files. These files are created on request from the user, dynamically, and displayed on the browser,
by including them in a jsp page.
Here we face a problem when they are to be included into the jsp page.
The error is the following :
//////// Error ////////
Could not find request dispatcher for the url CBECBC.xml
Could not find request dispatcher for the url CBECBC_Envelop.xml
The created files are stored in the "d:\pstudio35\desks\bank\BankWeb\".
We are using " <jsp:include page="...."/> " (dynamic jsp include tag), to include the xml files.
Problem 2:
And could you just let me know how to include a xml file in a jsp file,
so that the xml file is displayed in the exact format of xml(with the tags).
I am using Pramati Studio 3.5
Its urgent!!!
Regards,
Deepa Datarproblem 2:
either translate all < en > into < and > or display the XML in a textarea -
Adobe AIR Event Dispatcher Problem
I have created an AIR application, I have removed an component and again i added the same component. That time the event dispatcher of the removed component is been called again and again.How to resolve this problem. Urgent Reply ASAP......
The only idea that comes to mind is to keep the file on the dvd, then have your app install (copy) it on first launch.
Thanks for adding the bug. For others affected by this, please visit the bug and add your vote. All feedback is appreciated!
https://bugbase.adobe.com/index.cfm?event=bug&id=2938315
Chris -
That old 'disp+work.EXE dispatcher' problem - tried everything !
Hi,
I have been having the same problem as described recently in another thread (but didn't want to hijack it, hence this new one), where when I try to run the application server from the Netweaver 7.01 ABAP trial version there is an error: 'disp+work.EXE dispatcher not running'.
I have uninstalled and reinstalled a couple of times, and this seems to finish correctly (I delete the folders beforehand as explained elsewhere). I have edited my services file to make sure the port numbers are correct (and neat !). Basically the program seems to start up (green background) and after a minute or so goes yellow (after the error message has flagged up).
My system is an XP laptop, with plenty of memory/diskspace. I am a complete newcomer, so please be gentle with me.
Any ideas ? Or has everyone packed up already ?
Merry Christmas,
NickUninstall minisap installation. Than change computer name lower than 13 chars. My suggestion a simpler name like "minisap" .In most cases Microsoft gives complex computer name like yunus-ax8323akdm . With minisap installation your computer name is host name like PROD QA.After change computer name restart setup and re-install. You will see everything is ok. Sometime you have to start manually database from SAP MMC (console)
[Special Discussion about topic|http://www.ykburda.com/2009/01/how-to-start-dispworkexe-dispatcher/] -
Hi,
I have problems with the initiating the dispatcher+work service. The dispatcher gets to the running state but cannot connect to the message server and after that stops the whole process. The developer trace shows the following error message:
ERROR => DpShMCreate: ShmCreate SHM_DP_CA_KEY(rc=4) [dpxxca.c 181]
ERROR => DpIPCInit2: DpShMCreate [dpxxtool2.c 431]
DP_FATAL_ERROR => DpSapEnvInit: DpIPCInit2
DISPATCHER EMERGENCY SHUTDOWN ***
What could be the problem?
Thanks.Hi,
there are two possibilities
1. a system with the same system number is still running.
2. Another process is attached to the shared memory and it can't be
deleted. Check whether the start service is still running and
stopp it. Then try to restart the system
Please make sure
no disp+work with the same instance-number is running on this box
(it could also bee that there is an old instance of dpmon or MMC
is running).
Now if this is not the case then there can be a kernal problem.Just check the above things and let me know.
Award suitable points -
To all
The problem is that my request dispatching is not forwarding the request and I haven't got a clue why. I have a upload servlet which is working fine as it parses the request and the forwards you to the same jsp page or the next jsp page according to what values it extracts. However I have set up a bean to display the contentType() of each request which is sent to it from the jsp pages, however nothing is displayed when the request is forwarded from the upload servlet. this is what is happening .....
public class upload extends HttpServlet {
public void doPost( HttpServletRequest req, HttpServletResponse res ) throws ServletException, IOException {
HttpServletRequest request = _req;
HttpServletResponse response = _res;
parseMultiForm pMF = new parseMultiForm( _req );
Hashtable values = new Hashtable();
String param;
while ( ( param = pMF.getNextParameter()) != null) {
String value = pMF.getParameter();
values.put(param, value);
if (values.containsKey("submit")) {
String url = (String) values.get("reload");
RequestDispatcher dispatcher = getServletContext().getRequestDispatcher("/" + url);
dispatcher.forward(request, response);
if (values.containsKey("continue")) {
String url = (String) values.get("next");
RequestDispatcher dispatcher = getServletContext().getRequestDispatcher("/" + url);
dispatcher.forward(request, response);
The above servlet forwards the request to a jsp which does the following....
<jsp:useBean id="info" scope="session" class="InfoBean" />
<jsp:setProperty name="info" property="request" value="<%= request %>" />
However infoBean does not receive anything when the request is forwarded from the servlet??
Can anyone see anything obviously wrong?? is it to do with the JSP asking for the <%= request> and not receiving it because the request dispatcher has altered it in some way?
Thanks in advance anyone
Andy.I have exactly the same problem. I can�t make the servlet pass the request object to the target jsp.
Try not changing the request nor the response. Unfortunatelly due to the kind of job i do inside my servlet there's no way i can't touch the request. So if you can make it work with mi advice please let me know. -
Cairngorm events dispatch problem
Hi,
We are developing a Flex 3 AIR application on Cairngorm and
LCDS 2.6. The problem is some Cairngorm events don't get fired
which results in null reference errors. But when we put an Alert is
starts working. Can you suggest any solution and reason why its
happening.
Thanks,
OlegOne thing that will cause events to appear not to fire is
when you forget to instantiate your controller somewhere on your
mxml file. The events will dispatch, but the command won't get
executed.
Another one - if you create custom events and override the
constructor, you have to to call super(MyController.EVENT_TYPE) or
else your event doesn't get bound to the command. -
Dispatching problem in REM Planning Table
Hi,
I have encountered a problem in REM planning Table, from REM planning table when i m accessing Bar char planning table and try to dispatch the planned order it is not dispatching the order. I have checked the scenario is previously it was working fine but now it is not working with same settings can u guide me tht which settings affect the planning table dispatch. neither it was showing the capacity requirements, i have maintained the rate formulas is work centre and formula was working fine, i doubt it relate to SPRO settings kinldy give me hints where i can check n wht standard settings i have to make for planning table..Plz give some suggestion on this....
-
Fax Off-Ramp : Tiff Format Problem
Hello,
I'm actually configuring Fax Off-Ramp on a Cisco 2811 Router
When I sent an e-mail without attachement, it's working fine
When i sent an e-mail with a TIFF File encoded by the Cisco On Ramp Script, it's working fine
When I sent an e-mail with a Tiff File encoded by another programs, it's not working
The Tiff Cisco Encoding Method is CCITT Group 3 2D(T.4 2D)
The Tiff encoding method of other application is CCITT Group 4 2D (T.6 2D)
Is there a method to encode the Tiff File when sending an email to the Router ?
Thanks in advance for your help,I don't think there is any other method to encode the TIFF file while sending the email. Only the cisco's encoding method seems to work.
-
Hello, dear experts!
We try to set up a new web dispatcher for SAP WAS cluster (6.40 PatchLevel 87289.311) which is all done accoding to the help info.
However we can't use it as everytime I hit the Web Disp URL I am getting this error:
500 Dispatching Error
Dispatching Error
Error: -26
Version: 6040
Component: HTTP_ROUTE
Date/Time: Fri Oct 28 12:46:55 2005
Module: http_route.c
Line: 2351
Server: nrxqa8__00
Detail: no valid destination server available for '!ALL' rc=13
© 2001-2003, SAP AG
The web dispatcher profile we created is :
1. Profile generated by sapwebdisp bootstrap
SAPSYSTEMNAME = QA8
1. unique instance number
SAPSYSTEM = 03
1. Accesssability of Message Servers
rdisp/mshost = nrxqa8.NRXTOR.WORLD
ms/http_port = 3602
1. SAP Web Dispatcher Parameter
wdisp/auto_refresh = 120
wdisp/max_servers = 100
1. SAP Web Dispatcher Ports
icm/server_port_0 = PROT=HTTP,PORT=55555
1. SAP Web Dispatcher Web Administration
icm/HTTP/admin_0 = PREFIX=/sap/wdisp/admin,DOCROOT=./admin
1. Description of the Resource
icm/min_threads = 20
icm/max_threads = 40
icm/max_conn = 500
1. Communication Buffer
mpi/total_size_MB = 100
mpi/buffer_size = 65536
I really appreciate if you could help us with it... Any suggestions are welcome!
Thanks a lot!Hello Yuri,
have you setup the web dispatcher profile with the command:
sapwebdisp -bootstrap
? It would have tested the connection to the message server. I think the message server port is wrong. If your instance numer is 02 then the default HTTP message server port is 8102 and not 3602. 3602 is the port of the SAP own protocol.
Regards
Gregor -
I have a panel with a button. The panel have a MouseMotionListener registered, but when the mouse is over the button the MouseEvent stop to go to the panel and go to the button. How can i let the panel understand to "keep the event also for me" ?
This solution seems not optimal ....
//my button class
protected void processMouseMotionEvent(MouseEvent ev)
MouseEvent trick=new MouseEvent((Component)ev.getSource(),ev.getID(),ev.getWhen(),ev.getModifiers(),this.getX()+ev.getX(),this.getY()+ev.getY(),ev.getClickCount(),true,ev.getButton());
this.getParent().dispatchEvent(trick);
super.processMouseMotionEvent(ev);
Suggestions?
Thanks in advance.
-Marco BagnaresiI'm no expert but I would have thought that the best way to do this would be to have your panel listening for mouse events on the button aswell.
-
Event Dispatch Problem With Classes
I have a custom Timer class that pops up an inactivity alert
after 3 minutes. The user can then choose 'yes' if they are still
editing a record or 'no' if they are done. If they do not respond
within 2 minutes of the alert it assumes 'no'.
A 'yes' refreshes the timer and closes the alert.
A 'no' kicks them out of the edit state in the component that
the timer is called from.
The logic of the timer is working fine but it doesn't seem to
be sending the event to the component that called it so clicking
'no' (or remaining inactive) does nothing. I feel like I'm missing
something really simple or just misunderstanding the
eventDispatcher function. Advice please??
Code From LockTimer class:
public class LockTimer extends Sprite
private var threeMinuteTimer:Timer;
private var twoMinuteTimer:Timer;
public function LockTimer()
// creates a new threeMinute Timer
threeMinuteTimer = new Timer(1000, 180);
twoMinuteTimer = new Timer(1000, 120);
// designates listeners for the interval and completion
events
threeMinuteTimer.addEventListener(TimerEvent.TIMER, onTick);
threeMinuteTimer.addEventListener(TimerEvent.TIMER_COMPLETE,
onTimerComplete);
twoMinuteTimer.addEventListener(TimerEvent.TIMER, onTick);
twoMinuteTimer.addEventListener(TimerEvent.TIMER_COMPLETE,
onTimerCompleteB);
// starts the timer ticking
threeMinuteTimer.start();
public function refresh():void{
restart(threeMinuteTimer);
twoMinuteTimer.reset();
private function onTick(evt:TimerEvent):void{}
private function onTimerComplete(evt:TimerEvent):void{
//trace("first timer");
Alert.show('You have been inactive for several minutes. Are
you still editing this record?', 'Inactivity Alert',
Alert.YES|Alert.NO, null, alertListener,null, Alert.YES);
twoMinuteTimer.start();
private function onTimerCompleteB(evt:TimerEvent):void{
//trace('second timer');
//Alert.show('TIME UP', 'Inactivity Alert', Alert.OK);
dispatchEvent(new Event("timeUp",true));
private function restart(tim:Timer):void{
tim.reset();
tim.start();
private function alertListener(eventObj:CloseEvent):void{
// Check to see if the YES button was pressed.
if (eventObj.detail==Alert.YES) {
refresh();
}else{
//exit edit mode
//Alert.show('TIME UP', 'Inactivity Alert', Alert.OK);
dispatchEvent(new Event("timeUp",true));
Code From Component:
private var theTimer:LockTimer;
private function initializeHandler(event:Event):void{
addEventListener("timeUp",timeUpHandler);
private function timeUpHandler(event:Event):void{
Alert.show('TIME UP', 'Inactivity Alert', Alert.OK);
//editDone();
}so here is what i had to do to make this work:
1. I had to attach the listener to theTimer rather than the
component
2. I had to initiate the LockTimer constructor outside of the
function
3. I had to call the handler initialization function from the
component MXML
below is the revised code (with excess cut out)
<?xml version="1.0" encoding="utf-8"?>
<mx:HDividedBox xmlns:mx="
http://www.adobe.com/2006/mxml"
width="780" height="515" liveDragging="true"
creationComplete="initializeHandler()">
<mx:Script>
<![CDATA[
import mx.controls.Text;
import mx.rpc.events.FaultEvent;
import mx.rpc.events.ResultEvent;
import mx.controls.Alert;
import classes.LockTimer;
public static const millisecondsPerMinute:int = 1000 * 60;
public static const millisecondsPerHour:int = 1000 * 60 *
60;
public static const millisecondsPerDay:int = 1000 * 60 * 60
* 24;
//IMPORTANT!!!////////////////
private var theTimer:LockTimer=new LockTimer();
private function initializeHandler():void{
theTimer.addEventListener("timeUp",timeUpHandler);
private function timeUpHandler(event:Event):void{
editDone();
private function refreshLock(theLock:int):void{
var theTime:Date=new Date();
if(theLock==1){
theTimer.refresh();
theTime.setTime(theTime.getTime() +
(millisecondsPerMinute*5));
}else if(theLock==0){
theTime.setTime(theTime.getTime());
}else{
return;
form1.request.firmlockedTime=String(theTime.valueOf());
form1.request.firmisLocked=String(theLock);
private function editIt():void{
//see if it's being edited
if(checkLock()){
//if its being edited send a message
Alert.show('This record is currently being edited by another
user. Please try again later.', 'Record Locked',
mx.controls.Alert.OK);
}else{
theTimer.startMe();
refreshLock(1);
form1.send();
currentState="AdminEdit";
private function editDone():void{
refreshLock(0);
form1.send();
currentState="Admin";
]]>
</mx:Script>
</mx:HDividedBox> -
Hello,everybody,
I am new to LVOOP,now I try to utilize LVOOP to current project, but it seems that I encouter a strange dynamic dispatch problem, I draft two demo vi called System_CAN_Demo1.vi and Node_CAN_Demo1.vi respectively, they should have the same implement behivour. I add a break point on the block program located " ..\CAN\Network management\Wake up line\Execute.vi", and it should be dynamic dispatched as the execute method has been overriden. but It appears System__CAN_Demo1.vi normal while Node_CAN_Demo,vi abnomal.
please check out the attachment code for details.
Attachments:
Dynamic Dispatch ---Debug.zip 375 KBYour subclasses have two copies of the st variable, one in the superclass and one in the subclass itself.
By accessing it directly through a superclass reference, the "wrong" one is used.
In other words, don't do that. Your superclass already has the st variable, so there's no reason to declare it in the subclasses.
Also you should make the variables private and use getters/setters to access them. -
Why does Shock Wave keep crashing? Only crashes on Firefox browser.
Every time I use Firefox browser, I get the error message: "Shockwave Flash is either busy or it may have stopped responding. You can stop the plug in now, or wait to see if the plug in will complete." I also get another one saying that the "Silverlight script is still running" and then I have to wait several minutes before I can view the page. I have uninstalled Silverlight Flash and reinstalled, yet I keep getting either that message or the "script is still running" one ONLY on Firefox. It freezes my web page screen for several minutes. When I use Safari, this never happens. Plug-ins work just fine. It appears that without Silverlight or Shockwave Flash that I cannot watch any videos. I tried YouTube and couldn't open any videos without Silverlight.
Please don't suggest resetting Firefox because I've already done that. I still cannot open Yahoo.com home page because I keep getting an error message and I have to go around it by opening news.yahoo.com instead. I have Windows 7 on an Acer laptop.
Meanwhile I have reset my default browser to Safari, even though I don't have an Apple computer. It works better than Firefox. Are you planning on fixing the rampant plug-in problem with Firefox?I have the exact same problem on my ipad mini. It says 'google earth is running low on memory' and crashes.
Maybe you are looking for
-
Hi, I have attached my simulation loop.In the model attached i hav eone main pump with constant rpm which drives the 5 smaller pumps and fills the tank at the same time.As soon as the tanks reach their 90% level,the valves of the five pumps clos
-
How can I Add/Change Icon's for Bookmarks in Bookmarks toolbar?
My bookmarks toolbar at the moment has several links in it, most with just the icon(such as the YouTube logo). But some won't come up with icons, so I have to put a name next to it. I was wondering how I would go about adding an Icon there, so I can
-
RE: JAVA engine not starting
Hi all, We have problem with java engine. server0 process of J2EE engine is not starting. I am pasting the trace file trc file: "D:\usr\sap\SPS\DVEBMGS00\work\dev_server0", trc level: 1, release: "700" node name : ID1891050 pid : 8148 syste
-
I am having trouble connecting to 4g. I am always getting a sad face cannot connect to network
-
Ios 7 breaks charging, ios 7 breaks charging
Has anyone fixed the ios 7 problem with charging the ipad 3 ? I fiureed out how to work around it but what is wrong with Apple?