6032TAN_CAP pins not connected

Hi,
The 6032TAN_CAP-footprint fits exactly the SMD capacitors I bought.
When I add an electrolytic capacitor to the schematic, choose this 6032TAN_CAP as footprint (pic 1) and assign the pins to the nets (pic 2), both pins are not connected to any net in Ultiboard (pic 3).
Any ideas?
Regards,
Johannes
Solved!
Go to Solution.
Attachments:
1.png ‏293 KB
2.png ‏291 KB
3.png ‏304 KB

Hello Tintifax,
attached my test and it seems to work. I tested with MultiSIM and Ultiboard 13.0
Please check under edit footprint if the pins are mapped.
Hope it helps.
best regards
Alexander Glasner
AE NIE
Attachments:
6032TAN_CAP.zip ‏75 KB

Similar Messages

Custom Hardware Fan Control - problem if speed pin not connected?

Hi There,
I am planing to install a hardware fan control (poti) to my MacPro 1.1 rear fan. (because I have a defective northbridge temperature sensor and the fan is running at maximum speed... so i thought of slowing it down with a fan control for the pci slots)
I read that the pinning of the Fan is: Gnd, 12V, Speed, Control Pin (analog Voltage)
So when i would attach a fan control (just a poti) between some +5v and the Control Pin I think I should be able to control the fan manualy - am i right?
But then the speed signal is not the speed the mac pro fan control software think of... so would it be a problem e.g. if i disconnect the speed pin from the mainboard fan connector?
what would happen then? is the mac pro powering up the other fans for some kind of failsafe?
Or have you other suggestions how I can lower the speed of the rear fan manually?
thanks in advance,
Stefan

2010 2.8 Special $2119 - and throw in 6-core 3.3GHz yourself for $590
Take a look at the project some have undertaken to go with water block.
Send the motherboard in to have a 'skilled' electrician? repair the board perhaps.
4 fans, 3 under the control of SMCFAnControl utility. Maybe disable the one fan and make up for it with your own fan and running the others efficiently.
There are also VGA copper coolers.
FBDIMMs bleed heat: maybe the RAM fan cooler kit in there to deal with large source of heat. New higher density DIMMs are better made and few DIMMs = less heat even if 4GB.
Use ice packs, dry ice and liquid nitrogen to super cool :-)

Subcircuit pins do not align with grid and will not connect

I have two identical subcircuit symbols. One is just fine, but the other has pins that do not align with the MS grid, and one that will not even connect. MS12.0.0.
This one is fine:
This one pins are off grid. The circled one will not connect.
Solved!
Go to Solution.

Hi,
I have been experimenting a bit with this. One thing you can try is open the Symbol Editor, select the pin which is not connecting and then from the spreadsheet view, change the Shape to Zero-length Pin. Then try to see if you can connect the pin in the design. It will not appear as a line but you should still be able to connect to it.
If this does not work, you can open a service request and we can try to see how to resolve the issue.
Hope this helps.
Regards,
Tayyab R,
National Instruments.

V 31. installed would not connect to internet, restored to 30, now the pinned tabs due not persist between starting and closing FF.

Installed version 31.0 from version 30.0. It would not display any web pages, e.g. google, had a message about not being able to connect. Did a Windows system restore point to version 30 (I had created a restore point before the install) . FF will now not save pinned tabs between sessions and it will not restore the last page from a previous session. All it will display is the Default FF page.
Can someone give me some idea's about how to fix this. I tried reinstalling version 30 but that did not work to fix the problem.
Greg

Hi,
First, thanks for everyone responding. Here is what the problem was....
For some reason, there is a profile under Local in Mozilla and another profile under Roam. The Roam profile was the one that was being pointed to from the Troubleshooting tab under help. The local profile only had some partial files not including sessionstore.js. I copied all the files from the Roam profile to the Local profile. This restored the pinned tabs but not the open tabs from the previous session. I then updated Roam and Local profiles with the last sessionstore I could find in the Roam directory.... for some crazy reason this restored everything. Updating to FF v 31 was what initially caused this.
I did create a restore point before the update, which would not connect any tabs to the internet (e.g. Google). I then restored from the restore point, and ended up with the damaged FF v30 installation, which would connect to the internet but would not pin tabs and remember them or display the last page I had visited as a start page....
So, I hope someone gets a chance to look at FF v31, and why there is a Roam and Local directory with profiles in them ?
Thanks
Gv

New iPhone 5 will not connect to sync

I have a new iPhone 5 I got a couple days ago and it will not connect to sync in my car. I have a Ford Fusion 2012, and I had a 3GS that I used with it, and it worked perfectly for the few months I've had the car. I've tried everything with my iPhone 5 but it will not connect. It doesn't even ask me to put in the PIN. Sync shows the PIN and then I click on sync on my phone and it just sits there for a minute until eventually it says to make sure sync is on, in range and ready to pair. Any suggestions?

Read this it might help you http://www.apple.com/au/support/iphone/assistant/wifi/

IPhone 4s Sporadically not connecting to 3g even though the 3g symbol is displayed.

Hi,
I purchased my iPhone 4s (Simfree) from the Irish online apple store back in November 2011.
Since purchasing I was having a very annoying problem where by the phone would sporadically not connect to 3g but would display all the characteristics it was trying i.e. 3G symbol with little activity circle. The quickest fix was to restart the phone which would work again for a few days until it would happen again.
From experience, it seemed to happen more when I went from WiFi to 3G. If I had to give a guess I would say it was like it just couldn’t make the switch from WiFi to 3g and resulted in no internet when on mobile data. Note: It always worked on WiFi no matter what)
I tried all the usual things like restoring the phone to factory settings and closing all apps running in the background before leaving WiFi but the problem kept appearing.
After months of trying different configs I think I’ve finally solved it.
I enabled “Data Roaming” from settings\general\network and so far so good. The strange thing is, I shouldn’t need “Data Roaming” turned on as I don’t roam. My wife’s iPhone 4 and my last two iPhones all had this function turned off by default.
I decided to post this as it was so annoying; it actually took away from owning the 4s when it should be a joy to own. I only hope this helps someone else with similier problems to my own.
Thanks,
Mark
PS: Remember to turn “Data Roaming” off when traveling or you could end up for some pretty big bills

my wife's iphone 4S has the same problem. All of sudden 3G data is no longer working and battery is draining very fast, to the point that you can see the percent points going down as you look at the phone.
I found a solution on this forum http://www.iphoneforums.net/forum/iphone-help-15/4s-data-not-working-3g-23911/ that seems to fix the data problem at least. Don't know about the battery problem as I have just applied the fix.
I read on the Apple discussion forum about a quick easy fix that the German T-Mobile is telling their customers to do to circumvent this Apple software issue. The phones affected are apparently only the 4S with OS 5.0.1 (9A405). This fix works for about 80% of the 4S phones that have this problem.
Go to:
Settings>Phone>Sim Pin>Sim Pin Off.
You may have to reboot the phone for the change to take effect. The change works on my phone. Good luck. And thanks for nothing, Apple.

IPhone 4s IOS 6.1.3 will not connect to 2011 BMW 328XI

Hello,
I recently updated my iPhone to IOS 6.1.3. Everything appears to be working except I can no longer play music through my iDrive system. The phone connects fine to the stereo in my other car and can be controlled from the stereo head unit. I can also connect it to my home stereo through the headphone jack and that works flawlessly as well. When I connect it to my iDrive usiing the Y USB cable, the external devices just says not connected and nothing happens. I have tried reseating the cable and also cleaning the 30 pin connector on the phone but no luck. Has anyone had this happen? Should I just assume the cable has now gone defective and replace it?
Thanks!
4

Hi JimHdk,
I have also upgraded to ios6.1.3, and facing same wifi connecting problem, after upgrade my iphone3gs is not connecting to my laptop shared wifi, which was working perfect with ios6.1.2,
and its not an hardware error, its software error, crippy apple does not test their releases which causes problem to users.
Updates:
Earlier wifi connection which i was using on my Iphone 3gs, was WPA2, which was shared from my laptop via "Microsoft virtual WiFi Miniport Adapter", was working perfectly till ios6.1.2, but when i have upgraded my iphone 3gs to ios6.1.3, my iphone 3gs became unable to join wifi,
Today I have created "adhoc network" on my laptop using "Broadcom 4313 802.11b/g/n"(default wifi adapter of my laptop), and kept security type "WEP", and found my wifi working fine with my iphone 3gs,
So if someone using LAN internet on their laptop, they can share their LAN internet to use on their ios devices, via creating an 'adhoc network',
How to create an 'Adhoc Network',
choose Security Type : WEP (compatible with ios6.1.3)
http://www.youneedabudget.com/support/article/create-an-ad-hoc-network-in-window s
Vinay Rajput

IPhone 4s will not connect to the computer.

I have a multitude of problems with my 4s and I'm sure that I will never buy another Apple product again.
Within the first week, I was having problems with the microphone. No one can hear me unless it's on speaker phone, and I know it is not a software issue. The people at my phone company sprayed canned air into the phone and claimed it was fixed. It was, for a few months. Now it's back to doing it again. It works about 20% of the time off of speaker.
Then, it got stuck in "dock mode," which I tried EVERYTHING to fix it, and nothing worked. My phone had to be taken apart by a cell phone repairman, and you know what he found? A pin was shoved through the ribbon that connects the dock to the rest of the phone, and after so many months it started putting enough pressure on it to make it think it was cnstantly on a dock.
Now, it will not be recognized by my computer. I have tried EVERYTHING. Everything from this, http://support.apple.com/kb/TS1538. I have even cleaned out the registry of everything apple, itunes, and bonjour before reinstalling itunes, and I have even manually deleted and manually redownloaded, unzipped, and reinstalled the apple mobile driver device. At first, it said USB not recognized. Now, it won't even recognize anything is plugged in. And, it WILL NOT connect to it even in recovery or DFU mode. I have tried three cords and three computers. So, is this software or hardware related? Because honestly, this company isn't worth my time to try to send the phone to because they will do another half assed job like they did when building it. I'd rather just take care of it myself.
This phone is clearly defective, and I would just like a new one that at least WORKS, but Ntelos says that they can't even fix my phone. All they can do is charge me $120 a year for insurance, and then make me pay $200 for a REFURBISHED one, when I paid $250 for a NEW one and have done nothing, not even so much as dropped the phone, in the 5 months I've owned it.

You must use Apples iTunes in order to place ringtones or music of your own on the phone. You don't have an android phone which uses a sd card and can load via the usb cable.
If you need info on how to get songs and ringtones and photos on your phone read the manual on your phone or read up at http://www.apple.com

Can I connect my iPad mini to a data projector using a lightning to 30-pin adapter connected to a 30-pin to VGA connector? Or will this only work with a lightning to VGA connector.

Can I connect my iPad mini to a data projector using a lightning to 30-pin adapter connected to a 30-pin to VGA connector? Or will this only work with a lightning to VGA connector?

The lightning to 30 pin adapter does not support video as per the item description in the Apple online store:
http://store.apple.com/us/product/MD823ZM/A/lightning-to-30-pin-adapter
This adapter lets you connect devices with a Lightning connector to many of your 30-pin accessories.* Supports analog audio output, USB audio, as well as syncing and charging. Video output not supported.
You will need to the Lightning to VGA adapter directly
http://store.apple.com/us/product/MD825ZM/A/lightning-to-vga-adapter?fnode=3a
Or the Lightning Digital AV Adapter
http://store.apple.com/us/product/MD826ZM/A/lightning-digital-av-adapter
If the projector supports HDMI input.

Sometimes I get a message that says that safari is not connected to the web when I trie to get to a particular website. However, it will let me go other places on th web. The only time shutting it off and on again works is when I am at the apple store.

Sometimes I get a message that safari is not connected to Internet while trying to reach a certain web page for work. The onl time shutting it off and on works is when I am at the apple store. Then I will usually get it to work for another day. Is there some other trick

Hello Theresa818,
Thank you for using Apple Support Communities!
It sounds like the cellular data will not activate for some reason on the iPad.
I found this article that will help you resolve this issue here, named iPad (Wi-Fi + Cellular Models): Troubleshooting a cellular data connection, found here http://support.apple.com/kb/TS4249
Check for a carrier settings update.
Update your iPad.
Toggle the Cellular Data setting off and on under Settings > Cellular Data.
Restart your iPad.
Tap Settings > General > About. Locate the Carrier entry and make sure that your carrier is correct.
If your SIM card has SIM PIN enabled, try turning it off: Tap Settings > Cellular Data > SIM PIN.
Make sure you're in an area of good coverage. If the cellular data connection works in another area, contact your carrier to report the original affected area.
Reset network settings: Tap Settings > General > Reset > Reset Network Settings.
Restore the iPad as new.
If none of the above steps resolves the issue, make an appointment at an Apple Retail Store, contact your carrier, or contact AppleCare to troubleshoot further.
I know you may have done one or two of the steps here, so you can skip those.
Take care,
Sterling

Iphone not connecting to 3G

I have an iphone version 2 which has been currently update though i can not connect to 3g. I have used another iphone in a 3g area and that one connects to 3g whereas mine will still only connect to edge. been through all the setting and they are both the same. any ideas?

my wife's iphone 4S has the same problem. All of sudden 3G data is no longer working and battery is draining very fast, to the point that you can see the percent points going down as you look at the phone.
I found a solution on this forum http://www.iphoneforums.net/forum/iphone-help-15/4s-data-not-working-3g-23911/ that seems to fix the data problem at least. Don't know about the battery problem as I have just applied the fix.
I read on the Apple discussion forum about a quick easy fix that the German T-Mobile is telling their customers to do to circumvent this Apple software issue. The phones affected are apparently only the 4S with OS 5.0.1 (9A405). This fix works for about 80% of the 4S phones that have this problem.
Go to:
Settings>Phone>Sim Pin>Sim Pin Off.
You may have to reboot the phone for the change to take effect. The change works on my phone. Good luck. And thanks for nothing, Apple.

I have an ipad3 which has been spontaneously restarting and is not connecting well to either mobile service or wireless networks.

I have an ipad3 which has been spontaneously restarting and is not connecting well to either mobile service or wireless networks. It has become unusable. Is there a software update to fix this issue?
I have tried removing and reinserting the sim card - I am not even being asked to put in the sim pin to unlock the sim
I have reset the network settings and reconnected to my wireless network. I can get onto the wireless network but the ipad does not connect to my carrier even though my mobile phone (same carrier) has great service.
It seems to me that due to the connecton issue the ipad then restarts itself so I cant even use it for the local apps that do not require any connection to run because every few minutes the unit reboots.
heading to an istore tomorrow to have it looked at but wondered if there is a software upate or setting I can change myself to fix this isse.
not happy after the cost of the unit and ony had a few days use before the issues started!

Thanks Alan,
in the end it was replaced at the Apple iStore, they restored factory settings and it was still playing up for them too. Weird but the replacement is working perfectly!!

Ipad not connect with computer. error number (0xE8000084), ipad not connect with computer error number (0xE8000084)

ipad not connected to computer. erreo number (0xE8000084)

Hello Mohamed Abdo,
It sounds like you are unable to connect your iPad to the computer because you get this error code when you try. I would use the troubleshooting for these types of errors from the following article:
iOS: Unknown error containing '0xE' when connecting to a Windows PC
http://support.apple.com/kb/TS3221
Start with these steps, and there are additional steps in the article if you need them:
1. Restart your computer.
2. Install the latest version of iTunes.
3. Verify that your computer meets the minimum system requirements. iOS devices require the following minimum version of Windows:
Windows XP Service Pack 3
Windows Vista
Windows 7
Windows 8
4. Download and install any available software updates from Microsoft.
5. Connect the device directly to your computer; not to an external USB hub. Find out if your computer has USB 2.0 ports.
6. Check that the Dock Connector or Lightning Connector on both the device and cable are clean of any lint or other debris. If possible, connect your device using a different Apple 30-pin to USB cable or Apple Lightning Connector to USB cable.
7. Disconnect other USB peripherals from your computer, with the exception of your keyboard and mouse. After disconnecting these peripherals, restart your computer, connect your device, and open iTunes.
8. Connect your device to a different USB port on your computer.
Thank you for using Apple Support Communities.
Take care,
Sterling

Z10 Blackberry not connected to Link

My Blackberry link will not connect to my BB Z10 after I downloaded the new updated software 1.1.1.37. Worked before. Does not recognized any devise is connected. I wanted to connect my outlook calendar but it did not download the calendar either.
Fixes so far; I updated my phone from 10.1.0. 273 to 10.1.0.4181. Upgraded Link again to 1.1.1.41. Restarted both. It is not the the issue in my device manager, as I checked that. Connected with UBS cable as it is getting power.
I wonder what it is?
CB

There is also a new version of Link available this week.. download, install and try it.
Link updated to v1.1.1.41 (Windows OS)
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

My Z10 does not connect

Hi Z10 does not connect to my system Win7 Link is downloaded and it shows my z10 as connected but it does not allow me to sync it keeps asking for reconnect/reload i tried reloading few times none works i need help i am getting frustrated with this

Please review this thread:
Blackberry Link
and the questions asked, especially my last post in that thread with the three linked KB articles.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

6032TAN_CAP pins not connected

Similar Messages

Maybe you are looking for