6100 connectivity problems using Nokia CA-42 cable...

I have PC Suite 6-85-14-1 - the latest as at 11Feb'08, a new Nokia USB CA-42 cable, as listed for the 6100. The PC is recognizing the cable, but there is no recognition of the phone, within PC Suite.
I am attempting to download all the contact information and so on, from the 6100, to transfer to a new E51.
Incidentally, the E51 connection with its own cable to PC Suite, works perfectly. It is the 6100 connected through the CA-42 cable which is the problem.
Any solutions on offer?

Paulprior.
Just checking here that you need to have the drivers installed for your cable+phone.
If you have CA-42 cable, you should install Nokia PC Suite from
www.nokia.com/pcsuite
If you have DKU-5 cable, you need to (inaddition to PC Suite above) install DKU-5 cable driver
http://www.nokia.co.uk/nokia/0,,86571,00.html
If your cable is NOT genuine Nokia cable, it may require cable drivers provided by the cable manufacturer, but the cable might work with Nokia drivers also.

Similar Messages

WLAN Connectivity problems using Nokia 5800 Xpress...

Folks,
I really need help here.
I am trying to connect to my company WLAN called BLUESSO.
The visible config settings required to access this hidden WLAN access point are as seen in the attachment also seen below:
SSID: BLUESSO
Encryption type: TKIP
Network Authentication: WPA-Enterprise
EAP Method: PEAP
Inner EAP Method: GTC
Validation Server Certificate: Any Trusted CA-
Server Name: wlan.xx.com
My Phone is a Nokia 5800 XPressMusic
Firmware: 31.2.101 14-10-09mRM-428 (C)NMP - Latest Firmware
My Settings are:
I set up my phone as follows:
Data bearer: Wireless LAN
WLAN Network Name: BLUESSO
Network Status: Hidden
WLAN NETWORK MODE: Infrastructure
WLAN Security Mode: WPA/WPA2
WPA2 Only mode: No
WLAN SECURITY SETTINGS: EAP
EAP Plugging Settings:
    - EAP-PEAP
                        Personal Certificate: Not Defined
                        Authority Certificate: Thawte Server CA Tha.....
                        User Name in use: User Defined
                        User Name: 212058402
                        Realm in use: User Defined
                        Realm: wlan.ge.com
                        TLS Privacy: Off
                        Allow PEAPv0: Yes
                        Allow PEAPv1: Yes
                        Allow PEAPv2: No
                                                EAP-GTC
                                                                 User Name: 212058402
Advanced Settings:
    IPv4 settings: automatic
    IPv6 settings: automatic
    Proxy server address: gems.setpac.ge.com:1533/pac.pac
    Proxy port number: 1533
I can see the BLUESSO Access points. Signal Strength is always between 80% and 100%
1- Unfortunately, My phone is able to connect. Is there something wrong with my setting?
Any suggestions?
2- I also have the ability to connect using the 802.1x protocol used by Apple machines. Can you advice on settings please?
3- Is WPA Enterprise same as WPA2 in my phone or is there a special pluggin I have to download to get and WPA2 Enterprise security feature?
4- How to I access the TKIP encryption in my phone?
Can somebody provide me with some technical advise?
Thanks in advance
Joe
Nokia 5800 XpressMusic
V 40.2.005.236.04
Type: RM-428

Update to my Network Connectivity Dilemma.
Please correct me if I am wrong.
It seems I can use 802.1x WI-FI Security mode authentication to connect to WLANs that are configured for WPA2 Enterprise since both authentication methods use the same security settings in a WLan Infrastructure.
They both have EAP with similar EAP Plug-in settings.
If this theory is correct, then I can use my Nokia 5800 to access a WPA2 Enterprise authentication Wlan with the 802.1x WI-FI Security mode.
Objections any body?
Monk
Joe
Nokia 5800 XpressMusic
V 40.2.005.236.04
Type: RM-428

SAP Crystal Reports data source connection problem using sap business one

Hi,
I m facing a problem regarding: SAP Crystal Reports data source connection problem using sap business one
I am trying to create a Crystal report but when I try to configure a new connection it does not work.
I select Sap Business One data source and try to complete the information required to connection but it does not list my companies databases, what is the problem?
Our Current SAP related software details are as follows:
OS: Windows Server 2008
SAP B1 Version: SAP B1 9 (902001) Patch 9
SAP Crystal Report Version: 14.0.4.738 RTM
Database: MS SQL Server 2008 R2
I have also added some screenshots of the issues.
Please have a look and let me know if you have any questions or any further clarifications.
I m eagerly waiting for a quick and positive reply.

Hi,
There is problem with SAP Business One date source.
I had faced same problem, I used OLEDB Data-source, and it worked fine for me.
So, try to use OLEDB.
Regards,
Amrut Sabnis.

Connection problem with Nokia Lumia 2520 tablet

I found the problem when connecting Nokia Lumia 2520 Tablet to Linksys EA4500 router WiFi network "Wireless-N" mode. TheInternet and local network connection disappears after a few minutes, the ping test fails. In "Wireless-A" mode (5 GHz) and "Wireless-G" mode (2,4 GHz) connection is normal, but i need more speed!
When i have connect this tablet to the other routers in mode Wireless-N connectivity problems do not occur.
Reset the router and the tablet to the factory defaults does not help.
Router firmware version - 2.1.39.145204
Nokia Lumia 2520 have Qualcomm Atheros AR6x04 WLAN Adapter

Disable 5ghz wireless and use only wireless N.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Major problem using Nokia Test Message Editor

Using Nokia Test Message Editor on PC Suite 6.83 to create a new message (via USB cable), when I click on create new message (works fine) and then when I click on the "To" button, it says error. It asks me to close program as it has performed an illegal operation. Whys that? The only way I can currently get it to work is by manually entering the phone number but just cant use teh To button.
whats wrong?

No that's not helping, "oh boy".
I tried to Repair PC Suite from the Unistaller, same error.
Then I uninstalled PC Suite, restarted, ran PC Suite Cleaner 3.5 to get rid of registry settings and files. Then I noticed some old data in Application Data\PC Suite (old IMEIs) which I all deleted, then I restarted again and installed the newest PC Suite back. It asked me to install MMSync onto my phone, which I did. (see separate bug report on that
Then it gave me a message that some "Old Contact Browser data was found and has been moved to a separate folder", which I think is somehow related to the Contacts bug which I had described for a previuos PCS version, under my old nick "zak1974". Feeling good and all hopeful at last, I launched the Contact browser and it got all contacts with no problem, I went to Messages - Inbox. Clicked on Create New Message button, then "To" - only to find the same bug, which I am perfectly able to reproduce and describe on any level reaqired, as I have saved all screenshots and messages on the way to the Text Message Editor crash. All the above gives me some right to declare a software/firmware bug with the versions of products I had described in my first post.
Any other ideas?
N95 - King of Photos

Midi connecting problems: using Logic Express 9 with MBox 2 interface and a Mac OSX 10.6.8

I have a Mac OSX and I use Logic Express 9 on it. I also use an MBox 2 digidesign. Im having trouble connecting midi and getting it to work from my Roland Keyboard Midi, to the back of my Mbox 2 Midi. Its just not working at all. Does anyone know how to make Midi work with the Mbox 2 using Logic Express 9 on my OSX 10.6.8

Troubleshooting Wi-Fi issues in OS X
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)
Also try turning off Bluetooth

Bluetooth connection problem with nokia 6230i

Hi I am having troubles establishing a Bluetooth connection between my Nokia 6230i and my Dell Latitude laptop running on Windows XP SP2 when trying to use Nokia PC Suite. When using the nokia suite connection wizard it establishes a connection for a fraction of a second and then disconnects.
The following information may be useful??
Windows XP Pro SP2
Nokia PC Suite 6.5.12
Microsoft BT Stack 5.1.2600.2180
WIDCOMM BT Stack 3.0.1 build 803
Can any one help please??
Thanks

You could try uninstalling the Widcomm Bluetooth and relying only on Microsoft + PC Suite 6.6.18 from http://www.nokia.com/pcsuite

Max. Number of connections in use Nokia N93

Hi
I am trying to connect to wireless router using WEP. I have configured the access point and when I try to connect with Opera Mobile 3.6 an error occurs:
Max. Number of connections in use. Close na active connection first.
Note that my phone is not woring in dual mobe but GSM only.
When I try connecting with the Phone's browser:
WLAN: Unable to connect. WLAN Network not found
Lumia 920 OS version: 8.0.10521.155
FW revision number: 3047.0000.1326.2002

Every time you up-date the firmware, you get from your network opperator the settings for various access points (Internet, MMS, Vodafone Live, whatever....) This leads to duplicates (or even mode) access-points. Moreover, some of these access points are saved as "default" access point in various applications. This is where the mess starts.
To clean-up the mess, you first have to REMOVE all duplicate access points and keep only one access point for each purpose: Internet connection, MMS, Live (if you are are on Vodafone), etc. After this, you will probably get messages from various applications to define a new default access point. And things will be sorted our automatically.
Hope this helps, even though it might not be simple for some.
2110i, 6150, 6210, 6310i, 6670, 9300, 9300i, E90, E72, HTC Touch Pro2, Samsung Galaxy S, Samsung Galaxy S II

Wireless connectivity problems using IOS 6.0.2?

After installing IOS 6.0.2 on my iPhone 5 I can no longer connect to known wireless sites. I've been through troubleshooting with both Apple and my ISP and no luck. I'm thinking there's wireless connectivity problems with this latest update (my iPad 3 is still running 6.0.1 and is fine on my wireless network). Are others having this issue as well?

I am not guaranteeing this fix , but it worked for me , so far. I have an iphone 5 and it had ios 6.0.1 . Worked fine. Upgraded to 6.0.2 and it wouldn't connect with home router most of the time. My son in law an IT guy for the Government came up with a solution. The problem seemed most likely with routers that are bought and not configured and retain the original factory settings. Therefore my phone considers my home network a generic one and I have to manually connect to it. To distinguish the network we did the following.
1) went to settings on my iphone
2) choose "my home network" by pushing the arrow on the right
3) This brought up the network info page. (it says "forget this network " at the top)
4)DHCP will probably be highlighted.
5) touch "static"
6) This will bring up the manual settings
7) We entered the following.
For Ip Address 192.168.1.15
Subnet Mask 255.255.255.0
Router 192.168.1.1
DNS 4.2.2.1,4.2.2.2,8.8.8.8
Leave the HTTP Proxy to off
This will assign a static Ip address not a dynamic one and should work.
If it doesn't , go back to step 3 and select DHCP and return to the dynamic state .

Connection problems using LAN with WRT-160n

Hello everyone. I am having a big problem conneting to the internet using a LAN to my computer. The things that I have wireless are the PS3 and Wii, but they work fine (well except when I bought the Wii I had to change some Wireless Settings that i found here in the forums). When I just run my cable directly to my modem it works fine. As soon as I hook up the router the problems begin. I can use google and thats about it. Does anyone have any ideas??

It is possible that you are wirelessly connected to your neighbour's network and your router is not configured...
To configure your router follow this if your ISP is Cable...
If your ISP is DSL follow this

Connection problem of Nokia 6151 with Nokia Music

Hi,
I have a Nokia 6151 (RM-200), Firmwareversion 4.1.0 (which is the latest available), and the Nokia Music program (v. 1.3.20722.01). The USB connection cable type for connecting to my PC (Windows XP Home SP 2) is CA-53. In the past, when the music manager was integrated into the Nokia PC Suite, I had no problem with connecting the phone to the PC, and copying music to and from the mobile device. But since Nokia Music is a separate program, I am unable to connect the phone to it (note: this only refers to Nokia Music; the connection to Nokia PC Suite works fine). Whenever I try to connect, I get the error message that the device is connected in the wrong mode, and that I should select either "Media-Player", or "Printing & Media", or "Media-Data-Transfer" mode. But none of these modes is availableon my device. The modes actually available there are rather "Default Mode", "Printing", or "Data Storage".
Just as a further note: I have already un-installed the connectivity cable drivers, and re-installed the latest modules. To no avail. Can anything be done here? Is my device model (6151) at all suitable to be connected to Nokia Music?
Cheers
blueray
Solved!
Go to Solution.

I have contacted Nokia support directly, and I have been told than indeed the 6151 does not work with the newest version of Nokia Music. Only thing what helps is to re-install an older version of Nokia PC Suite, where Nokia Music is still integrated.
blueray

GPRS Connection problem with Nokia 6230i

Hi All,
I am using the GPRS activated Vodafone sim for Nokia 6230i.
I am not able to access the GPRS connection from my J2me application, it’s always shows me that "Subscribe GPRS first" but its already activated.
When i change the sim & checked with nokia N-72, my application started working fine & able to make the proper http communication.
What could be the problem?
Do i need to do some extra settings for Nokia 6230i?
Is Nokia 6230i having some problem while accessing HttpCommunication ?
Please suggest me.

Getting a gprs connection on series 40 phones is very difficult. You first need to create your own access point based on the gprs settings for the network you are using. You do this in settings -> Configuration -> Personal configuration settings -> add new
I use the settings from
http://www.filesaveas.com/gprs.html
When you have entered in the data, press back and select preferred access point and select the one you created.
I think then you should be able to use gprs in your application
I test with google maps

Having network printer connection problems using a Macbook Pro

I hope a "greater mind" can suggest a solution to the following problem:
Up until 2 days ago, I was successfully connected to the network printer at my office using both my Macbook Pro at work and at home (both wirelessly, OS 10.6.8). From yesterday, however, I now only receive the following message when I send a file for printing: "network host (and then its IP address) is busy. Will try again in 10 seconds."
All right, my system admin. advised me to re-install the printer on both computers. I did. In printer set-up, 1) Protocol: Line Printer Daemon - LPD; 2) Address: the IP address of the printer; 3) Queue: secinmac. This is the queue name specifically for Mac use and given to us by the company who installed our network printer; 4) Name: we use the printer's IP address; 5) Location: left blank; 6) Print Using: Generic PCL Laser Printer. Further for 6), in the "installable options" dialog box, I click "Duplexer". Then, finally, I click "ADD". The printer is added.
However, when I try to print a file, I continue to get the "busy" message. The file spools for about 3%, and then the "busy message" appears, and I cannot print. You can imagine how frustrating this is when the problem has arisen from one day to the next! A colleague who also uses a MacBook Pro sent a file to print on the network printer today, and he had no problems! I, however, have no success !
Any ideas that can help me? Thanks, in advance!

Thank you for taking the time to respond.
Yes, I tried this when I was reading a bit of Apple communities history on this matter, and it did not work. I also tried this, and then rebooted my Mac, but to no avail! While I was at the office today, my system admin also logged into our network and tried to get something to print on his Mac, but he now has the same problem as I do.
He gets the "busy message", too !
I'll try to see if I can get a solution from APPLE by going through my support service agreement.....From reading the history on this issue, I would have thought that APPLE would have worked on this to come up with a fix by now...!
Thank you again for your suggestion! Cheers.

Connection Problem using oracle.jdbc.xa.client.OracleXADataSource

Unable to get a connection from connection pool Realm1tx
Actually there are 5 connection intialized but no connection is there in active pool.Sometimes when I
go to weblogic console and refresh the connection comes alive temporarily.Can anyone help me out for
fixing this problem
Driver Used:
oracle.jdbc.xa.client.OracleXADataSource
Error Message
Unknown error occurred: XA error: XAER_RMERR : A resource manager error has occured in the transaction
branch start() failed on resource 'realm1tx' null sql=[SELECT Person$1.id,NULL,Person$1.id,NULL,NULL
FROM Person Person$1 WHERE (Per
son$1.securityId = 'admin')] throttle=[-1]
java.sql.SQLException: XA error: XAER_RMERR : A resource manager error has occured in the transaction
branch start() failed on resource 'realm1tx' null
Thanks in advance.
Ragavendra.

Which version of oracle thin driver are you using? Oracle 920 thin driver has some issues.
Thanks,
Mitesh
Ragavendra wrote:
Unable to get a connection from connection pool Realm1tx
Actually there are 5 connection intialized but no connection is there in active pool.Sometimes when I
go to weblogic console and refresh the connection comes alive temporarily.Can anyone help me out for
fixing this problem
Driver Used:
oracle.jdbc.xa.client.OracleXADataSource
Error Message
Unknown error occurred: XA error: XAER_RMERR : A resource manager error has occured in the transaction
branch start() failed on resource 'realm1tx' null sql=[SELECT Person$1.id,NULL,Person$1.id,NULL,NULL
FROM Person Person$1 WHERE (Per
son$1.securityId = 'admin')] throttle=[-1]
java.sql.SQLException: XA error: XAER_RMERR : A resource manager error has occured in the transaction
branch start() failed on resource 'realm1tx' null
Thanks in advance.
Ragavendra.

Problems using Nokia Messaging on E61

Hi all,
I'm new here so I appologize if the problem has already been reported or if I'm using the wrong part of the forum for this issue.
After having installed Nokia Messaging (of which I'm pretty satisfied) I cannot access the options button at least on agenda entries and on the gallery files. This happens after opening the entries/files.
Has any solution been already found for this issue?
Thank you very much!

Hi all,
I'm new here so I appologize if the problem has already been reported or if I'm using the wrong part of the forum for this issue.
After having installed Nokia Messaging (of which I'm pretty satisfied) I cannot access the options button at least on agenda entries and on the gallery files. This happens after opening the entries/files.
Has any solution been already found for this issue?
Thank you very much!

6100 connectivity problems using Nokia CA-42 cable...

Similar Messages

Maybe you are looking for