6163 pro-long beep

hi,
Recently I have installed a new harddisk and window ME.After installed the window ME,I found that my computer alway reboot itself once the window come out.Could someone please tell me why does happen and how to solve?
After I try to play the bios setting,suddenly my computer alway beep when I try to boot. And the bios also show message that my computer had a abnormal hardware and the loading will only continue if I hit any button. May I know what is going on and teach me how to solve this problem.
thank for your support....

thanks for your help,but I think it still didn't work.
I had checked my cpu fan and it is still functioning.
Then,I try to change the bios setting which learn from mike,it still didn't work.When I boot my computer,the beep sound still play 3 time and hang over there.
Actually the beep sound didn't come out at first.After installing window ME,I found that my computer always restart itself without my notice.So I thought the bios is problem and I try to set the bios to default.After this,the beep sound always come out once reboot the enjin.
Is there any bios setting I should pay attention?

Similar Messages

Mac Pro early 2008 power off suddenly alone and gives a long beep on startup

Hello everyone! Can you resolve the problem reported? I have 6 equipaments identical to those with the same problem, some worse than others, and only two barely functioning, others are stopped. They power normally and suddenly alone they power off , and after that I only can power on again , after hours waiting or only the next day , and when it's power on , on startup , they give me a long beep , before the chime , then I can work for a time (minutes or long time , it's not secure)
I talked with Apple Computer (from USA) and they do not assume that the problem exists and that many users have the same problem, worldwide.
If you're not satisfied with the result of Apple, we will have to press them to assume the defect and promote a recall on these equipments. We have many users with the same issue (MacPro off alone)

All places where I have my equipments (they are in 4 different places, but I have tested them in all four locations), are electrically grounded, the electrical networkstabilized, reviewed annually and I use UPS minimum of 1.5 KVA (I have two UPS of 3.75 KVA) . I tested with the original HDD , with all the applications that I use installed , only with the system installed and the same procedure on a new HDD and got the same result . So , it is not eletrical problem . I have iMacs , MacBooks , G5 and MacPro early 2009 working in the same places with no problems . I tested all the sites with three different electricians and all
approved my Electric networks . As I know, all Apple equipment have
surge protection, precisely to prevent thecomponents from being damaged
by electrical problems. Again , it is not eletrical problem .

HT5860 What about if when I start up my MacBook Pro it makes 3 short beeps 3 long beeps and 3 short beeps. Or is that the same as 3 long 3 short 3 long?

The screen does not turn on and makes 3 short beeps 3 long beeps and 3 short beeps again then turns itself off. Well I just tried to turn it on again and now there are no more beeps but instead just a black screen. The LED light in the front of the laptop is on and not blinking. Does anyone know what be wrong with my laptop?
Also this is a 2010 model I believe

Read this:
http://support.apple.com/kb/HT5860
Ciao.

Long beep on start up

When I turn on my macbook pro there is a long beep. Not all the time but often enough... any ideas ?
David

Try resetting your SMC.
Resetting the System Management Controller >>
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
iTunes: MacOSG Podcast
 An Apple User Group 

6163 pro v2 / 6905 v2.3 PIII 800eb HELP

My system is (or was) as follows
MS-6163 Pro v2, 500 Celeron on MS-6905 v2.3, 320Mb Ram (2x128 pc133, 1x64 pc100), TNT2 m64 32Mb, 13Gb + 40Gb Segate HDD's, Diamond Data 36x CD-rom, Iomega 650i CDRW, Lucent Win modem, Aztec 2320 sound card. It has never played up in the last 3 years, but I decided to bite the bullet and get a newer/faster CPU.
Ok here's the problem, when I installed the 800eb & removed the 64m pc100 SDRAM (after flashing the new MS-6163 Pro W6163IMJ3A0 BIOS Release) and set it to 133 x 6 the system will boot but crashes/locks up loading Windoze ME.
I figured out I had a dodgy SDRAM and removed it, system ran fine at 800Mhz yesterday, yet today it started crashing iexplorer every few minuets (not the system). Upon rebooting it started behaving the same as yesterday. Seemed like a ram problem again.
Setting the CPU to 8 x 100 (hoping to alleviate ram problem) results in the CPU booting up as a 600e. It runs fine and stable although I find no real world increase in performance over my trusty old 500 Celery. I want to get it to run at 800Mhz.
The system is now as I type:
CPU PIII 800eb running at 600Mhz (100 x 6, even if set to 100 x 8 in BIOS) which boots as a PIII 600e.
BIOS 10/11/2000-i440BX-W977-2A69KM4KC-00
RAM AMD 128mb 16x(8Mx8) SDRAM PC133U-333-542 (CL3 up to 133Mhz)
I can't find any reference to the 6905 v2.3 anywhere, mine is identical to the v2 BUT J3 has only 3 pins on my board not 4 as in the documentation for v2.
As for the 6163 should I leave SW2 & SW3 set to auto or set the CPU bus to 100.
Any help would be most greatfully accepted as the 800EB set me back AU$165 and there is no point running it at 600.
Thanks in advance
OH! Almost forgot, the sound card no longer works. Weird??

Hi guys,
I assumed as much reguarding the 800eb multiplier and after some fiddling last night managed to coaxs it to run at 744Mhz (6x124) and so far appears to be running ok with the AGP at 83Mhz. I'll see how in goes over the next few days.
The only reason I bought the 800eb is that it was listed here
Supported CPU's
and even after flashing the new BIOS it only allowed up to 8.5 multiplier which to me ruled out anything over 850 if retaining 100Mhz FSB.
I'm still curious though as to the J3 difference between the ver2 of the MS-6905 Master (4 pins) and mine the ver2.3 (3 pins)

6163 Pro dead??

Hey all,
I've been running my 6163 Pro v2.0 board (bios v3.a) for a few years with no problems at all. Last night my monitor suddenly went blank. I tried to restart but got nothing.
I opened up the case and tried to restart again. I saw that the diagnostic led's were stuck at 2) green 3) red 4) green 5) red. According to the manual, it has something to do with the VGA bios or the card not installed correctly.
I'm running a ATI AIW 32MB AGP card. I tried to reseat the card but the same thing happened upon restarting, lights stuck at green - red - green - red.
I've tried a PCI video card, same results. I've tried clearing the CMOS (several times), replacing the battery, pulled every card out of the board except the video card, one stick of memory, two sticks of memory, changed the power supply, and even tried different processors and still no luck.
Is my BIOS to blame or is the board just dead?? I can't try to recover or reflash as the system won't even POST.
Any help would be greatly appreciated.
yawny

System:
Intel celeron 1.8 Ghz
Matrox G400 dualhead 32MB
Windows 2000
Mainbord: MSI 645 something (6 months old)
Problem:
I was playing space cadet in windows 2000 when the system suddenly hung up. The picture went into bizzare patterns and i restarted. It froze again and I restarted. Now there is a serie of 9 beeps when poweering on the computer and the beep starts when 2 and 4 are red on the bracket. It stops beeping and 1 2 3 are red while 4 is green. The monitor is blank. Something with the videocard? NO. Tried another videocard, Hercules Prophet 64 MB Geforce 2 and that didn´t work either. Tried to unplug every card except for the videocard and it didn´t work. The funny thing is that it DID started ONCE during boot up but it zone froze again when listening to music.
What is teh matter with my computer?

Two short beeps 1 long beep 5 times then sequence of 8

Two short beeps 1 long beep 5 times then sequence of 8 short beeps at end of turning on desktop computer.
2 short beeps and 1 long beep (repeats 5 times) Unable to initialize video or video card required but not installed
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c02222922&lc=en&jumpid=reg_r1002_us...
I unplugged everything thing externally from computer even monitor all usb ports etc... now what do I do any suggestions.
My computer will not display but does stay powered up.?

You might start with mentioning the computer model, and if you have added a Graphic card?
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

Problem with a MSI-6163 PRO

Anyone got an idea what kinda problem i have? I have an MSI 6163 PRO motherboard (with latest BIOS update 3.5), a PIII 700 Cuppermine, 3x256 SDRam, i run Win XP Pro, have a 40 gb harddrive and have been running like this for at least 9 months, without any problem. Suddenly it starts to reboot all the time and now i cant even start it not even in fail safe mode, it reboots before i get in.
Its not a Virus, i have virus checked the hardrive, i tryed with a smaller harddrive (6 gb and win 95) and that worked, i bought a new harddrivce (120 gb) Started to format and install Win XP pro and it starts to reboot again, i have tryed chagne memmorys, graphic adapter, net adapter, soundcard everything, i am going nuts! anyone had probs like this??
I would be more than greatfull if anyone has an answer to this.

Thanks a lot Wonkanoby for the help. It didnt help my error but it sure cleared it up. There were several capacitor that leaked, just as the pics on the site you sent http://www.overclockers.com/tips00140/, it shows clearly on thoose. Cant beleive how that problem can be so big and seems like they are doing nothing about it either.
Well thanks for a great Forum here, and thanks to you Wonkanoby.
The motherboard is dumped... thinking of going back to good old ASUS
Then its Rock´n Roll agian
Have a great day.

1 long beep and 2 short beeps

hello this is my second post....before i had problems with me8 bios, then downgraded using this forum tool..thx for that.
now i can boot my PH67A-C43 (B3) board and use it normally, but my problem is that when ever i try to restart or boot it again without waiting i get 1 beep with is normally the one which indicates that system is OK and then 1 long beep and 2 short beeps and no display on the monitor....i can only boot my PC if i let it turned off for 5 or more minutes...this is really annoying!!
specs:
Operating System
   Microsoft Windows 7 Home Premium 64-bit SP1
CPU
   Intel Core i5 2400 @ 3.10GHz   32 °C
   Sandy Bridge 32nm Technology
RAM
   8.00 GB Dual-Channel DDR3 @ 665MHz (9-9-9-24)
Motherboard
   MSI PH67A-C43 (MS-7673) (SOCKET 0)   37 °C
Graphics
   VX2250 SERIES (1920x1080@60Hz)
   ATI Radeon HD 5700 Series (ASUStek Computer Inc)
Hard Drives
   56GB OCZ-AGILITY3 (SSD)   30 °C
   149GB SAMSUNG HD161GJ (SATA)   24 °C
Optical Drives
   SONY DVD RW DRU-880S
Audio
   Realtek High Definition Audio

i heard about the full cmos clear yesterday....after the flash i just pressed the clear cmos button at the back panel...but now i did the full clear...
well i have an aerocool e80 700w psu...i was thinking it might be the psu...then i tried on my old 500w coolermaster psu and it worked fine(i could restart as many times as i wanted/no blank screen)
then i hocked back the aerocool to confirmed if it was at fault and POOOFFFF no more blank screen.i restarted any time with no problem...how can it be?what caused the blank screen and BSOD?
i will try to use the PC as much as i can and see if i get any blue screen...will keep u posted
***memory is Kingston 4*2gb.i ran memtest86 it found no error over 2 hours...i never overclock anything

Won't start up - 3 long beeps and 1 short beep repeated

As I was watching Netflix, the display went crazy and displayed horizontal lines and the computer froze.
I held the power switch down to shut it off.
After restarting, seemed to work fine for a few minutes, then same thing happened.
Reset again. Seemed to start up fine (heard the chime and the hard drive going) but no display output.
Reset again. Got the start up chime, a white screen with horizontal lines, and I get 3 long beeps and 1 short beep repeatedly.
Any ideas?
Thanks for your help in advance.

The beeps you're hearing means the system has no usable memory. You can try reseating the memory or swapping for other known working memory (pain as it is to open the mini up). Otherwise, typically that means it's new logic board time. See this Apple article: http://support.apple.com/kb/HT1547

Fail to boot (short-short-short-long beep code) after M92p BIOS Update

Hi,
I recently updated my BIOS to the latest version using the System Update tool from Lenovo. For a while everything seemed to be working alright, as the BIOS was dowloaded and the computer rebooted. After rebooting the first time i was presented with the BIOS utility, and noticed that the update was progressing.
After 20 or so seconds the computer rebooted again. This is where my problems began. The computer immediately started beeping this short-short-short-long melody from the speakers. I thought this was normal, so I left the computer on for quite a while.
However, the beeping never stopped. Now the beeping resumed the instant i plug the power back in. I have yet been able to actually getting any sort of information on-screen telling me what's wrong.
I've tried following the "Recovering from a POST/BIOS update failure" on page 267 of the Hardware Maintenance Manual, but no luck with that so far. No matter where I place the jumper, the beeping code is the same short-short-short-long melody (yeah, it sounds like a disney tune or something).
Any bright ideas? The machine type is a M92p 2992-B3G
I'd hate to have to send it in for repairs, and Lenovo's Norwegian support line doesn't open until Monday, and there seems to be no way to call their 800-number in the states from here
Oh, and would this be covered by my warranty if repairs / motherboard replacement is the only way out?
UPDATE #1:
I found this in the manual;
3 short beeps and then 1 long beep DRAM memory
error
Perform the following actions in order.
1. Make sure the memory module(s) are properly seated
in the connector(s).
2. Replace the memory module(s).
3. Replace the system board.
This is pretty much Lenovo's way of saying "You're screwed", isn't it?
UPDATE #2:
I've now tried pretty much everything;
The solution as proposed on page 267 in the Hardware Maintenance Manual
Unplugging all cables and harddrives before booting
Removing my PCIe video card and PCI Wireless NIC before booting
Removing all memory modules, and trying 1 and 1 module
Moved a memory module from another machine that I know is working
No luck so far.
Ideas would be welcome at this point

I'm glad to hear it's just a simple memory error, however the original problem in this post is a bit more than just a memory problem.
This became a problem after a BIOS update, so somewhere along the way one of Lenovo's developer screwed up badly, and it's been bugging me ever since. There's absolutely no way for me to use any PCI-e card with my M92p.
I've tried 6 different cards, 3-4 different memory module combinaties, with our without harddrives plugged in, and every thinkable combination of these.
No luck. Therefore, I simply conclude that Lenovo are dicks, and we all know what dicks enjoy doing; **bleep**ing people over.
I've given up on the issue, and I'll never buy a Lenovo again after this.

When system is switch on(poweron) long beep and display is coming after hour

hello sir
when system is switch on(poweron) long beep and display is coming after hour
This question was solved.
View Solution.

Hello @anandgopinainar,
I am not quite sure what you are trying to say here. I would be happy to assist you, but first I would encourage you to post your product number for your computer. I am linking an HP Support document below that will show you how to find your product number. As with this I can provide you with accurate information.
How Do I Find My Model Number or Product Number?
As well if you could please elaborate on what is going on so that I understand it would help as well.
Please re-post with the requested information and I would be happy to provide you with assistance. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

K8D Master-F 2 long beeps

I have a K8D Master-F, it makes 2 repeating long beeps (high and low pitch) after a few seconds when powering up. The CPU is in CPU1. If I move the CPU to socket 2, the board powers up but no beeps. The only time it beeps is then a CPU is in CPU1, also I tried 2 CPU's, One being an Opteron 244 and a 242 (No i am not using dual at this time). Having the RAM in or out seem to have no effect with getting the beeps. Any ideas?

More spec's please.....
Check the BIOS for case-open detection, turn it off....
If it still makes the noise, check the piowersupply.
Also, JPWR2 should NOT be connected....

6163 pro & 950 Celeron

I wander if my 6163 Pro is going to work with a new CPU that I intend to get from a friend of mine: A 950 Mhz Celeron (it has 126 Kb of L2 cache so I think it's Coppermine based - I don't have a clue on the FSB though). I use the board with a 566 Celeron that I overclocked @ 850 Mhz. Thanks.
I also want to know if a good slocket adapter is to be found anyware.

http://www.msi.com.tw/program/support/cpu_support/cpu/spt_cpu_detail.php?UID=113%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20&NAME=MS-6163%20Ver2.0
assafs better on the adaptors

I cannot boot up my Mac book and all I get is a long beep

I cannot boot up my Mac book and all I get is a long beep
Have tried checking the keypad and no luck
Is this a logic board issue or is it something else?

My daughters Mac crashed mid assignment and after hours for phone support. So was looking to see if there was anything we could do here. Your advice is correct but the issue was "long beeps". Which are generally a serious issue and not one that we are going to be able to deal with. Like the icon .... and do appreciate the fact that you were happy to help. cheers

6163 pro-long beep

Similar Messages

Maybe you are looking for