6230i cable problems

connot see the files on my computer via cable connection - on my other 6230i the files came up after i click nokia browser in my computer. my new 6230i does not do this, why? i have nokia suite installed but still cannot access my images on the phone via cable connection.
Also how can i save my pictures to my memory card,

See this:
/discussions/board/message?board.id=pcsuite&messag​e.id=12503&query.id=240160
and try without memory card..

Similar Messages

  • My iPhone 4 is no longer recognised by my laptop, and no longer registers being plugged in to charge, even though it will charge slowly if plugged in and turned off. It's not a cable problem or a computer problem, as I've checked these.

    Hey, over the past couple of days my iPhone 4 (GMS, Model A1332, EMC 380B - running on iOS 7.1.2) has begun inexplicably intermittently not recognizing being plugged in to charge or being connected to my laptop. As of today, it has complete stopped recognizing being plugged in to charge or connected to the laptop.
    If I plug it in to charge, whilst it is on, nothing happens and the battery drains.
    If I plug it in to charge and turn in off, it will charge very very slowly - though it will charge fully after a long time.
    When I connect it to my laptop, nothing happens - it doesn't appear in iTunes, and it doesn't charge or recognize being connected to the laptop (there is no charging symbol, no noise from either phone or computer registering the connection as it usual did, or another sign of any connection between the devices, though, again, it will charge very slowly if turned off).
    I've ruled out the possibility of it being a cable problem, by using a friend's cable and finding that didn't allow it to recognize being plugged into the wall to be charged either, or being plugged into the computer.
    My friend's cable does work on their own iPhone (ie, when plugged into the wall with their cable, their iPhone acknowledges this and charges properly, and when plugged into my computer with their cable both my computer and their iPhone recognize the connection).
    So, it's definitely a problem with my iPhone itself, but I don't know what.
    As I say, it will charge very slowly, if it's switched off whilst it's plugged in, but it won't acknowledge being plugged in, and will only drain if it is turned on whilst being plugged in - and it will not recognize being connect to my computer.
    Please help me figure out what is wrong with it, as this is beyond annoying and I'm literally banging my head against the wall - the iPhone is little over a year old.
    Cheers.

    You clearly did not notice that you have joined a USER TO USER COMMUNITY FORUM
    This is NOT Apple ,Apple do not read nor do they  therefore respond
    So if you would like to wind your neck in ........................
    try a reset of iPhone and then a restore,best, as new and if it then functions correctly try restoring with your backup

  • Thunderbolt display video died-Cable problem??

    My TD (paired with a Retina) video seems to have lost its video.  Audio working fine.  Could this be a cable problem?

    I can confirm that the Thunderbolt Display will work when plugged in to the 2011 MacBook Pro 15" and a 2011 Mac Mini Server connected via Apple's Thunderbolt cable.  When both systems are connected to the monitor, the display will always prefer the system connected to its display port,  when it sleeps or is powered down, the other system detects the available display and connects to it automatically.  I can't imagine a more ideal sinerio!
    Thank you Apple!
    Jason
    Nerds Limited

  • Solaris 8 says: "Link down, Cable Problem?"

    I have these on my home LAN:
    1. Sun Ultra 5 Solaris 8
    2. Win 2000 PC
    3. Win NT laptop
    They are all hooked into a LinkSys Router.
    The Router is hooked into my Motorala Cable Modem.
    Here's the problem:
    The PC and the laptop can see each other on the LAN.
    The Solaris 8 is only visible on the Lan INTERMITTENTLY.
    The lights on the Router for the PC and laptop are always ON.
    When I reboot the Solaris box, the lights on the Router sometimes come ON, and sometimes they stay OFF. When they stay OFF, I see the message: "Link down, Cable Problem?" during reboot.
    I have tried different cables, and tried various combinations of the 4 avalable ports on the back of my Router.
    If I plug in the Sun box DIRECTLY into my cable modem, then I don't see the above message. (but then I don't have a LAN anymore)
    Please help, I've been struggling with this for a while now.
    Thanks,
    Irshad Ahmed (I am relatively new to Sun)

    Hi
    You have not indicated if you have the router ethernet ports working
    at 100Mbps or 10Mbps. Depending on this sometimes, Sun systems may
    not be correctly auto-negotiating their ethernet port settings.
    You may set these parameters to force Sun Ultra 5 to a 100Mbps mode or a 10Mbps mode.
    For forcing it to 100Mbps, Full Duplex mode and disabling the auto-negotiation, put these entries in /etc/system:
    set hme:hme_adv_autoneg_cap=0
    set hme:hme_adv_100T4_cap=0
    set hme:hme_adv_100fdx_cap=1
    set hme:hme_adv_100hdx_cap=0
    set hme:hme_adv_10fdx_cap=0
    set hme:hme_adv_10hdx_cap=0
    Conversely, if you want to force your Sun to work on 10Mbps, Full
    duplex mode, (if your router does not support 100Mbps) in the same
    /etc/system file, put the following entries :
    set hme:hme_adv_autoneg_cap=0
    set hme:hme_adv_100T4_cap=0
    set hme:hme_adv_100fdx_cap=0
    set hme:hme_adv_100hdx_cap=0
    set hme:hme_adv_10fdx_cap=1
    set hme:hme_adv_10hdx_cap=0
    One of these should solve your problem. You need to reboot the system
    after putting these entries.
    You can also check the port at the OK prompt using the command
    "watch-net". This test the onboard ethernet interface.
    You may also apply the hme patch released by Sun that fixes many
    known problems with hme ethernet driver. The patch id is 108981-03.
    It is available from the site :
    http://sunsolve.sun.com
    HTH
    Shridhar
    Sun-DTS

  • Hme0: Link Down - cable problem?

    i've a problem i've buyed an ultra 10 (used)
    i've reinstalled solaris 10 01/06
    when it boot the o.s. it give this error message "hme0: Link Down - cable problem?"
    and network don't work.
    i cannot ping my router but i've gave to my sun an ip of the same netmask (sun ip 192.168.1.88 router ip 192.168.1.1)
    i've checked the cable and it's good (it work with a normal pc)
    the led on the switch is on (it's green)
    maybe i need some patch
    how can i do?

    gio,
    You didn't necesarily do anything wrong.
    You do not necessarily have any broken equipment.
    There may just be somthing that is incomplete in the setup.
    Begin by checking if your network settings were set up correctly by running:
    <b># ifconfig -a</b>
    (it's usually best to troubleshoot while you are root user)
    If the output from the <i>ifconfig</i> command seem to be complete, you could always think about reconfiguring the NIC all over again.
    If you are not sure, then just paste the entire output results back here.
    Also, use the forum search function, using keyword <u>sys-unconfig</u>.
    Next, read the Solaris man pages for sys-unconfig.
    That command will force you to repeat the setup of the connection.

  • Howto Link Down-Cable problem?

    Hi,
    I am having a Ultra Sparc 5 with a hme interface and a quad card. When the machine boots it checks at boot prom level all 5 interface and reports for all qfe interfaces "Link Down-Cable problem?". All qfe interfaces do not have a ethernet connx but I also do not want to deinstall the quad card. Is there any possibility to turn thoose "interface checks" off.
    Thanks Marcus

    Never mind I just figured out that thoose checks just run after the boot cdrom command.

  • Is this just a LVDS cable problem? Help please

    http://img.auctiva.com/imgdata/1/1/3/1/9/0/5/webimg/371736702_o.jpg
    I was told that this could just be a LVDS cable problem, but I've also read it could be a logic board problem. Any help would be appreciated.

    OK, the above was the report after the MacBook had been plugged in for a few days. I decided to see what came up when I started on the battery, but the first time I tried it, as soon as Safari launched (it's a login item) it went down. So I let the battery get back up to 100%, and restarted, bypassing login items. System Info reported this:
    Battery Information:
      Model Information:
      Manufacturer:          DP
      Device Name:          ASMB013
      Pack Lot Code:          1
      PCB Lot Code:          0
      Firmware Version:          102
      Hardware Revision:          300
      Cell Revision:          200
      Charge Information:
      Charge Remaining (mAh):          4120
      Fully Charged:          Yes
      Charging:          No
      Full Charge Capacity (mAh):          4273
      Health Information:
      Cycle Count:          37
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          -2054
      Voltage (mV):          10705
    I note that those last two items are quite different, and indeed, the voltage had been reduced to < 11V. Dunno if that's significant.
    I then tried launching Safari and it promptly went down. It occurred to me that the issue might involve Safari specifically in some way, so I let the battery charge back up again, de-logined Safari, and restarted. I was able to launch a few smaller applications; then I launched Backup, so far so good, but when I tried actually starting a backup, poof.
    It's too bad I can't either find a MacBook to borrow to try with my battery or borrow a battery; no one I know has an appropriate model MacBook.

  • CA-42 SOLVED USB CAble Problem !

    Here is the answer to many CA-42 Cable problems people are having.
    First, Nokia says you must use their cable. NOT! The problem with the Chinese cables I found is the pins are not even. With a file, file down the pins so they are all the same length. With 1 or 2 pins longer than the others, the remaining pins do not make contact. Do not file down the longer ones any farther than the short ones. It will work !
    It works. I have been trying to get this resolved for 3 days. Filed the pins so

    Try uninstalling PC Suite, and also the Nokia Connectivity Cable drivers from Control Panel (Add/Remove Programs).
    Then download and install the latest version of PC Suite with the latest cable drivers from:
    http://www.nokia.com/pcsuite

  • White screen on my 3gs, i would like to spot the problem if it is a cable problem or an LCD problem?

    after dismantling the iphone 3gs and reassmble it again i got a white screen, i would like to spot the problem if it is a cable problem or an LCD problem?

    Steps for iPhone white screen, #1 Reset. If fixed done. If the screen becomes normal, but then again goes back to white screen, fix is new LCD Display. If remains continuous white screen after Reset, then the problem could be Logic Board or LCD Display, in this situation try a new LCD Display hoping it will fix issue, but will not if problem is Logic Board fault.
    Before opening and during all repair of iPhone 3GS make sure it is OFF. This is why you now have a White Screen, try not to make that mistake again.

  • 6230i - connectivity problems with cable, infrared...

    I have just had my phone replaced by my company as I was experiencing coneectivity problem. I have installed (and uninstalled) PC Suite and tried to connect my laptop to my phone. I get the following problems with each method:
    1. Bluetooth - cannot authenticate phone
    2. Cable - doesn't connect - nothing happens.
    3. Infrared - I get a message telling me infrared is not supported.
    This happens even though my laptop recognises something is trying to connect to my phone.
    It's driving me insane!

    Radders
    Please check your device manager if drivers are installed. If no
    then 1st uninstall PC suite. Connect your phone and re-boot. The windows ( I hope you are using 32 bit version ) will recognise a new hardware and will install all the required drivers. Please be patient till you get a pop-up telling your hardware is ready to use. Now install PC suite & try to connect.Message Edited by babdi on 13-May-200710:11 AM
    If my post has helped you please click the white star on the right

  • Nokia 6230i Malfunction problem

    my phone is nokia 6230i and i have DKU-2... i downloaded new version of PC suite...when i try to connect my phone to my PC, there's an error popping "ONE OF THE USB DEVICES ATTACHED TO THIS COMPUTER HAS MALFUNCTIONED..." pls help me im tired searching how can i find solution..pls help...whats the problem of this...

    Hi sarzosa,
    Usual solution :
    Uninstall Nokia PC Suite, PC Connectivity Solution, Nokia Connectivity cable driver, Nokia flashing connecitivity cable driver(if any on your pc), run pc suite cleaner. Install latest pc suite from nokia.com/pcsuite. Reboot your pc, then connect your usb in different ports of your PC and then check

  • 6230i Synchronisation Problem

    Hi,
    I am using the latest PC Suite for Nokia 6230i. I am using the DKU-2 cable on windows xp sp2.
    I can upload all the contact details using Outlook 2003 onto the phone.
    However I cannot synchronise any updates without having to make a new connection again.
    I get this error message.
    PC Sync has encountered a problem and has terminated the synchronisation.
    Just one little thing, we use Novell Groupwise as our main emailing system. Outlook is just the front end. In the Pc Synch Settings, the Microsoft Outlook Profile setting is set to synchronise with Groupwise.

    What do you mean by writing "new connection again"? DO you mean new settings for PC Sync application?

  • Nokia 6230i MMC problem

    hi everybody.i'm using 6230i almost a year and ihadn't any problems...by now...recently i had the following problem:i transfered 2 JPG files from PC via bluetooth.i saved one of the files in the MMC amd the other in the phone's memory.the free space of the MMC decreased (i checked it via "memory status" option).but the file disappeared and i can't find it when i look in the folder!!!after that i tried to move the other JPG file from phone's memory to MMC.and the same thing is happened-the free space decreased but the file dissapeared.so stange...then i moved other file(which was saved in the phone earlier) to MMC(because i thought thah the files are damaged) but the same thing again. in fact my MMC is almost full - there is only around 500kB free space.but i think that it can't be a problem(the files are smaller than the free space).i suppose that the formatting of the MMCcan sovle the problem but it's my last option.can someone tell me what's the nature of that problem and how i can fix it without formatting if it is possible.thanks.

    help me pls.i have a big problem.i tried to format my MMC but it was unsuccessfully and now i don't know what to do...firstly i tried to format it via the phone.i made the back up of the saved data and used the option "format memory card".a message "memory card formatted" is appeared on the screen but the card wasn't empty.then i tried to delete the saved files one by one via PC using USB-cable - unsuccessfully again(in that moment i used the phone in "data storage mode").finally i tried to format the MMC directly via PC using the window's menu(file -> formatting...) but even that couldn't help me.i see similar thing(unpossibility to format some kind of memory) for the first time.what's the situation now:my MMC seems to be empty(when you look in it) but when i check the "memory status" option it shows "11MB used".how it is possible.i have no idea..

  • Going from DVI to DVI cable from VGA  to DVI cable problem

    Got a mini with the VGA adapter to DVI working with no problem. When I decided to hook up a DVI to DVI cable, I got no picture. I had to reach behind the mini, press the power button to put it to sleep, then press the power button again to wake up the mini again to get a picture. The monitor is a 20.1 inch AOC monitor. The picture is sharp in both cases. The DVI to DVI setup is slightly smoother.

    After I reboot I still get no picture. I have to reach behind the mini, press the power button to put it to sleep, then press the power button again to wake up the mini again to get a picture.

  • USB Cable problem with HP Photosmart 7960 printer

    This may sound like a stupid question but I just bought a new 7960 printer to replace my old 7960 which has two out of the three ink cartridge holders broken and the usb port on the new printer won't accept a usb cable. It appears to be blocked by a cap insert over the connector prongs which will not come out. Any suggestions?

    Here is a link with some troubleshooting steps that may help to solve the issue you are having with your printer:
    http://h10025.www1.hp.com/ewfrf/wc/document?docnam​e=c02065582&cc=us&dlc=en&lc=en&product=3940574&tmp​...
    Paper feed problems are a hardware issue, if none of these steps help I would recommend contacting HP for upgrade options. I have included a link with directions for contacting HP:
    http://www8.hp.com/us/en/hp-information/summary/ww​-contact-us.html
    I am an HP employee.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"

Maybe you are looking for