6233 Voice activated calls
Hi,
The voice activated function on the 6233 works quite well and recognises most of the names in my phone book. The system behaves inconsistently when a contact has more than one number linked to them.
For contacts with only one telephone number, the system dials their number within a second of me selecting their name entry.
However, for contacts with two or more numbers such as Mobile and Work, I choose the number to dial (after selecting the right contact) and have to wait for 6 seconds for the system to display the "calling...." screen. Is there a short cut? Why is there such a long delay for contacts with multiple phone entries?
I have version 4.91 of the software.
Thanks
David
Actually, the 6233 DOES have voice recognition. The phone will recognise the name you say and find the contact for you without you having to record voice tags. Just press and hold down "Names" and speak after the beep.
Similar Messages
-
6233 voice activated dialling feature. TERRIBLE!!!
For the last 30 mins I have been trying to find a way of recording my own voice tags for voice activated-calling on my 6233. What a waste of time. I think it is ridiculous that Nokia has not included this feature and according to the previous posts they are not going to put it into an firmware updates. I still have my Nokia 6230i which I think I will start using again. There are things I like about the 6233 but there are to many glitches, also the font for the time whilst in stand-by mode not only looks terrible but is hard to read. What are the people at Nokia thinking? They have put a load of junk on to the 6233 and not put the useful stuff that was on the 6230i on it. I've used Nokias for 8 years and I am now seriously considering getting a Sony Ericsson next time I can get an upgrade. WISE UP NOKIA!!
03-Mar-2007
11:45 AM
kludgefactor wrote:
The new voice recognition that appears in almost all of Nokia's latest products does have built-in training, called adaptation, which means over time and with use the accuracy should increase.
The trouble with speaker independent voice recognition is that for some people, the accuracy is good enough from the outset, but for others it is not. This is why adaptation is included in the Nokia version to help improve the accuracy - but it is hidden from the menus.
You can test this adaptation by using the voice dialler and if it gets the name or command correct, select that name or command. This tells the voice recognition to adapt to your voice. If you don't select, then it won't adapt.
If this is repeated for several names or commands, then the accuracy should start to improve.
Another problem is that sometimes people have strange names in the phonebook that can sometimes spoof the voice recognition - it is worth listening to any strange phonebook names using the "playback voice tag" just to make sure.
Kludge
that's alot to do especially when you don't have lots of time on your hands. its kind of ridiculous IMO. if it wasn't like that then names wouldn't make a difference whether its french or spanish or transfered from your sim, that's the names that confuses the voice dialler and causes it to come back empty, with the wrong name or a list of names. a headache while driving.
everything happens for a reason
check out my blog @ http://mycellife.blogspot.com/ -
Can you initiate voice activated calls through BT Headset?
This is the million dollar question.
Does the iPhone 3Gs allow you to initiate voice-activated calls through a Blue Tooth Headset?
Can anyone here who has the 3Gs verify that they can do this?I have the jawbone prime and also can not get the voice control to work. This was confirmed in the review over at www.mobiletechreview.com
THIS *****!!!!
I've been waiting a long time to have quality voice control on the iphone. Bluetooth connected voice control is the only real safe way to make a call while driving.
How can Apple be so stupid to not include that option. It's bad enough they didn't include voice control in the iphone 3G, but not to include the simple option of using a bluetooth headset...dumb.
It's just dumb.
FIX THE PROBLEM APPLE! -
I purchased a Treo 700 WX today and I'm trying to activate the voice activated calling. Is this model equipped with the appropriate software for this action or do I need to download/purchase it?
Post relates to: Treo 750 (AT&T)Hi.. Welcome to the Palm forums. Voice command is part of windows mobile, to set it up follow this link. You may have to copy it into your browser but it will explain the process. http://forums.palm.com/palm/board/message?board.id=software&thread.id=7279 . Hope that helps..
Post relates to: Centro (Sprint) -
A 6233 user should be able to record their own voice tags on their phone.
This is a board for improving Nokia Discussions not improving phones, If you want to tell nokia Contact them by pressing the 'Contact us'
Nokia N95
V 20.0.015
0546553 -
Making a call with voice activation
I have been using a Palm for 5 or 6 years that has allowed me to make calls by either naming the individual (voice command) or saying the numbers. It is invaluable (and much safer) while driving. Does either the iPhone or any Third Party software support this capability?
Hello,
We can't even have the phone in our hands while driving in Québec. I currently have a Blackberry pearl and wanted to switch to the Iphone but without voice activation calls I won't... I only have to push on the main button on my bluetooth headset and tell my contact to have the call placed. Does this apps allow for some "automation" like when I get in the car I activate it and then I don't need to push any buttons on the phone ?
Thanks -
I have been trying to find a way to poll my 6500 for the total number of active calls via SNMP. I am looking to get this data into a graph made by MRTG.
From the CLI, I get the data via 'sh port voice active call'
Anyone have an idea?There are no separate MIB modules defined for the 6608 card. However, if you want to see the number of completed calls from Call Manager, you can use the performance monitor counters. To view the number of completed calls, start up performance counters, added a new counter, select "Cisco MGCP PRI Device" under Performance object. One of the counters is "CallsCompleted". This should show you what you're looking for. For more information, visit
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00800c4cd1.html#36551 . -
What is the command to check if there are any active calls before restarting the voice router?
what is the command to check if there are any active calls before restarting the voice router? thanks
Hi.
I can suggest show call active voice or show voice call status or show sip-ua call brief in case of SIP TSP.
HTH
Regards.
Carlo -
How do I unlock voice activation on iphone
How do I unlock voice activation on iPhone 4
Hi Kilted Tim, thank you for your quick response.
Yup, I've had the unlimited plan for about 4-5 years, and I do everything I can to keep from losing it, for obvious reasons.
As you advise, I've been using the iphone in airplane mode with wifi activated which works fine when I am in wifi range. But of course when I'm out and about I want to use my data roaming for internet, maps, skype, whatever so I take it out of airplane mode.
The trouble is that I get incoming calls and am charged international rates even when I dont answer. I havent looked lately but I think AT&T charges me for one minute even for unanswered incoming calls.
Any ideas?
Many thanks! -
Isdn Layer 1 deactivated when there is no active call
Hi All,
I am in Nairobi Kenya. Here we use ISDN Basic-net3 and my problem is that most of the telco switches here deactivate Layer 1 when there is no active call.
When I try to initiate a call by using the ISDN test call command I get an error to the effect that B channel is not available.
The only way I can initiate a call is I first call the line then and then disconnect. Then I have about 5 seconds to make a test call and pings are successful. How do I make the router initiate a call when layer 1 is deactivated.
the debug isdn q921 out has nothing till a call comes in.
I also understatnd that European ISDN switches deactivate Layer 1 when there no active call. I dont have a problem with one of the switches, coz it does not bring down the line when there is no active call.
Thakx in advance
MartinThanks for the quick response.
It is a cisco 1760
The IOS is c1700-sv3y-mz.122-15.T5.bin
When I try to make a test call the show isdn status initially indicates that the router is trying to activate layer 1 then after 5 seconds it indicates that it is deactivated.
I have not yet configured DDR as indicated in the config file
Building configuration...
Current configuration : 3054 bytes
! Last configuration change at 00:38:54 UTC Mon Aug 9 1993
! NVRAM config last updated at 00:36:54 UTC Mon Aug 9 1993
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Gill-House
logging queue-limit 100
enable secret xxx
ip subnet-zero
no ip domain lookup
isdn switch-type basic-net3
no voice hpi capture buffer
no voice hpi capture destination
class-map match-all voice-traffic
match ip rtp 16384 16383
policy-map voice
class voice-traffic
priority 24
class class-default
fair-queue
gw-accounting syslog
interface Loopback0
description Loopback interface for VoIP Dial-peers
ip address 128.1.x.x.255.255.255
interface Multilink1
bandwidth 6
ip address 128.1.x.x.255.255.252
ip tcp header-compression iphc-format
ppp multilink
ppp multilink fragment-delay 20
ppp multilink interleave
multilink-group 1
ip rtp header-compression iphc-format
interface FastEthernet0/0
description Gill-House LAN
ip address 128.1.x.x.255.255.0
speed auto
interface Serial0/0
description Link to Head Office
bandwidth 64
no ip address
encapsulation ppp
no fair-queue
ppp multilink
multilink-group 1
interface BRI1/0
ip address 10.10.1.2 255.255.255.0
encapsulation ppp
isdn switch-type basic-net3
isdn point-to-point-setup
keepalive 20
router eigrp 100
passive-interface FastEthernet0/0
passive-interface Loopback0
network 128.1.0.0
no auto-summary
no eigrp log-neighbor-changes
ip classless
no ip http server
logging source-interface Loopback0
logging 128.1.1.179
call rsvp-sync
voice-port 2/0
cptone GB
ring frequency 50
voice-port 2/1
cptone GB
ring frequency 50
dial-peer cor custom
dial-peer voice 2 pots
destination-pattern 101
port 2/0
dial-peer voice 51 voip
destination-pattern 100
session target ipv4:128.1.0.254
ip qos dscp cs5 signaling
dial-peer voice 55 voip
destination-pattern 120
session target ipv4:128.1.31.254
ip qos dscp cs5 signaling
dial-peer voice 52 voip
destination-pattern 102
session target ipv4:128.1.91.254
ip qos dscp cs5 signaling
dial-peer voice 53 voip
destination-pattern 103
session target ipv4:128.1.121.254
ip qos dscp cs5 signaling
dial-peer voice 54 voip
destination-pattern 110
session target ipv4:128.1.21.254
ip qos dscp cs5 signaling
dial-peer voice 56 voip
destination-pattern 130
session target ipv4:128.1.41.254
ip qos dscp cs5 signaling
dial-peer voice 57 voip
destination-pattern 140
session target ipv4:128.1.111.254
ip qos dscp cs5 signaling
dial-peer voice 58 voip
destination-pattern 150
session target ipv4:128.1.61.254
ip qos dscp cs5 signaling
dial-peer voice 59 voip
destination-pattern 160
session target ipv4:128.1.71.254
ip qos dscp cs5 signaling
line con 0
logging synchronous
line aux 0
line vty 0 4
password housing
login
ntp clock-period 17208074
ntp server 128.1.1.211
ntp server 128.1.0.254
end
Gill-House# -
I get an icon indicating that the plantronics M1100 headset is connected and working properly on my display. The headset even asks me if i want to answer incoming calls. But when i say "answer", i can only use the handset or speaker phone. I cannot get an active call to go to my headset. This just started happening. If there is a setting i am missing in the iPhone 4s please let me know. thanks!
I am suddenly having a similar issue with my Motorola H17 bluetooth headset. it is pairing/connected with my iphone 4. i can use the voice control feature to dial a number. but i cannot get any audio and cant answer calls from the headset.
-
Suri conflict with voice activation
Suri and Voice Activation - I have discovered an issue when using a bluetooth headset, when activating voice control via the bluetooth to call someone, if Suri is on the call cannot be completed. There seems to be a conflict between Suri and Voice activation from bluetooth.
Well, I have never come across this issue before, but it sounds like a quality of service issue and not really a port issue of any sort so I doubt opening any type of port will fix anything. If your ONT allows it, try bypassing our router with the linksys and see if the problem is fixed. Just want to verify it is the actiontech router causing the issue...
-
Automobile Voice activation and IOS7
Ever since upgrading to IOS7, my voice activation does not work in my Buick Enclave. Is there a fix for this? Buick says it is an Apple thing.
It is called VoiceOver
See:
iPhone: Configuring accessibility features (including VoiceOver and Zoom)
Try using three finger to scroll. Also try triple clicking the Home buton to turn off and then go to Settings|>Accessibilty to really turn off. -
I have just bought the Nokia 7100 Supernova - I wanted to stay with Nokia because of the voice activation and having a hands free kit in the car. Firstly I can't figure out how to set up voice activation & secondly, although I have twinned the phone with my active device in the car & they look connected, when I try & make or receive a call nothing happens - usually the radio cuts out & the voice comes through the speakers & this isn't happening - help!!!!!
1. In the standby mode, press and hold the right selection key or the volume down key.
A short tone sounds, and Speak now is displayed.
2. Speak the name of the contact you want to dial. If the voice recognition is successful,
a list with matches is shown. The phone plays the voice command of the first match
on the list. If it is not the correct command, scroll to another entry. -
X3 - 02: Voice activation
Just acquired the X3. Have been used to making a call by use of Bluetooth headset by pressing a button and saying the name of the person I want to call. The old method does not work on this model. Do I have to do something to set up voice activated dialling?
Solved!
Go to Solution.In case anyone thinks of researching this - don't bother.
I have now discovered that this phone does not support voice activated dialling. (Yes - in 2010 this basic Bluetooth function is not provided.) This information has come from a specialist at Nokia , who himself expressed amazement that this is the situation. None of the Sales staff at the shop I bought the phone were aware of this - but they are now, and intend not to push this to other unsuspecting customers.
In short - if you need to use your phone whilst driving, this is not the model for you.
Maybe you are looking for
-
Could someone who has dns set up correctly confirm that this test works?
The test that's here http://docs.info.apple.com/article.html?artnum=106798 says if you attempt to visit this link: http://17.254.0.91 and you are taken to Apple's page then you probably don't have your DNS set up correctly. Can anyone confirm, who ha
-
Ical will not delete or add new events to subscribed calendars on iPhone or iPad
So, The crazy thing is...all of this works fin on my iPhone. But, my wife, she has an iPhone, and iPad, and a user lognin on our computer where she keeps all of her calendars. She subscribes to my calendars as well. If I add anything to my calendar.
-
Need to trigger Save in ME22N - ME_PROCESS_PO_CUST
Hello fellow gurus, Riddle me this: How can I trigger a SAVE in ME22N in the context of BAdI ME_PROCESS_PO_CUST? I have created a custom tab at the Header level so that our users can put data in the fields and populate the fields in the Purcha
-
I also cannot get the welcome screen to open up. What have i done wrong and how can i put it right.It was working alright to start with.
-
Is there anyway in PL/SQL that I can force output to wrap to the next line? I'm working on a report that shows questionnaire questions and some of them are pretty long. My current setup truncates the question if it goes past 60 characters, anymore th