6248 connected to 3750 yet ports not configured as trunkport

I've setup a 2 5108's with 6248 Fabrics and my ethernet uplinks are going to a 3750x. I'm not proficient with all that comes with switching but I manage to get my systems up and running effectively. After installing my esxi's on the systems I noticed that all of them were getting DHCP addressed from my network yet although I enabled my uplinks and configured them as 1gb I hadn't move the patch cables to the uplink ports on the 3750 configured as Trunk ports. Now in the past this was a show stopper. Am I missing something here. And lastly, I intend to aggregate some links with Port Channeling which is easy enough on the UCS but a note states the upstream switch needs to be configured as LACP.
In short:
1.) Do i need to configure my ports on the 3750 as Trunk dot1q or has something changed and it's auto-sensing
2.) To do the Port Channel does it require Trunk or Switch and is it absolute that I configure LACP on the upstream 3750.
Thanks

I understand Trunking, a little however, when it comes to the UCS fabrics I have never been able to configure the upstream switch with anything other than Trunk Mode where I connect my ethenet uplink ports. Yet using a newer 3750x it is running without trunkports where my uplinks are connected. This is not normal. My test....I moved the patch cables to the configured Trunk Ports on the upstream 3750 and it stopped working, moved them back to the switchports and it started working. Next to this system is another with an earlier model 3750, (sorry I'm missing the specifics) and this will not work with the switctport mode, yet when plugged into the trunk ports of the upstream 3750 it works fine. As for Vlan's I have one other than Vlan 1 which is always the way I've configured these. I've configured about 15 sets of fabrics and only this one is acting this way.
As for the Port Channel configuration thanks. I'm assuming that even in trunk mode I can set LACP.

Similar Messages

HT4262 WI-Fi not working says air port not configured

Wi-fi not working says air port not configured, help]

Life is getting more complicated to do support..
You need to tell us what version airport.. extreme or express and the model number. A1xxx from the label.
You need to tell us OS.. if the profile which says 10.6.8 is wrong.. as that is confusing.
The new AC version Extreme needs 6.3 version airport utility which is only available for Lion or mountain Lion.
You might also need to turn on ipv6 local-link to get it to show in the utility.

Air port 'not configured'

Why does my airport give the 'not configured' status when i did not touch it? The previous day it was ok but suddenly it became like that. i cant seem to do anything and the troubleshooter dosent help. how do i 'configure' it? HELP!

Life is getting more complicated to do support..
You need to tell us what version airport.. extreme or express and the model number. A1xxx from the label.
You need to tell us OS.. if the profile which says 10.6.8 is wrong.. as that is confusing.
The new AC version Extreme needs 6.3 version airport utility which is only available for Lion or mountain Lion.
You might also need to turn on ipv6 local-link to get it to show in the utility.

Desktop software. serial port not configured properly

i cant seem to configure my serial port. actually i just dont know how.....ive went into serial setting but i cant seem to find a port number. it doesnt detect anything.....????? can someone with some patience pleeeeeeeese help me. thx alot

Port is supposed to be auto detected!! Have you tried detecting the port manually by going to connection settings and pressing detect button ? Which version of desktop manager your're using?
tanzim
If your query is resolved then please click on “Accept as Solution”
Click on the LIKE on the bottom right if the post deserves credit

Error "Test Agent could not connect to the test controller" while configuring the Test Agent on Client machine

Hi,
I am getting an Error “Test Agent could not connect to the test controller”
while configuring The Test Agent on Client machine.
Pre-requisite used:
VS2012 update 4, Test agent & Test controller of same version used
User has TFS admin access.
Same user id used for configuring Test Agent.
Description:
Test controller is installed on server A. I want to install test agent on client machine B.
Windows Fire wall is OFF on both Machines A & B. While configuring Test Agent below error is occurred:
“Test Agent could not connect to the test controller”
In log file error was “I, 2015/04/02, 15:32:21.723, Could not get the status from the test agent. Exception: Failed to connect to an IPC Port: The system cannot find the file specified.”
In Event viewer below error details given:
Unable to connect to the controller on ‘My Server: 6901’. The agent can connect to the controller but the controller cannot connect to the agent because of following reason: The requested name is valid, but no data of the requested type was found.
Make sure that the firewall on the test agent machine is not blocking the connection.
Could you please help me to find solution?
Thanks in advance!
Kanchan M
Kanchan

Hi Kanchan,
So on each computer, you create a local user account that is a member of the Administrators group, and use the same account and password on each machine(controller and Agent), am I right?
Could you enable the detailed log message?
http://blogs.msdn.com/b/aseemb/archive/2010/03/07/how-to-enable-test-agent-logs.aspx
http://blogs.msdn.com/b/aseemb/archive/2009/11/28/how-to-enable-test-controller-logs.aspx
>>In log file error was “I, 2015/04/02, 15:32:21.723, Could not get the status from the test agent. Exception: Failed to connect to an IPC Port: The system cannot find the file specified.”I
met a similar issue before which was related to the Firewall exceptions, maybe you could refer to it here:
http://stackoverflow.com/questions/12249093/test-agent-could-not-connect-to-the-test-controller-vs2012-agents
Best Regards,
Jack
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Error 633: The modem (or other connecting device) is already in use or is not configured properly.

Hi all,
I recently got that a new USB CDMA modem which works fine on Windows 7 system but when I try connecting to my other laptop which runs on Windows 8.1, it keeps giving the error:
Error 633: The modem (or other connecting device) is already in use or is not configured properly. I've most of the links and solutions shared but none seems to work. I've generated diagnostic logs which are as follows. I interpreted some and most probably
it seems like an issue of incompatible driver, but does anyone else sees any issues in these diagnostic logs. Looking forward to your suggestions.
[4724] 06-01 20:01:56:314: ENTRY: Reading "Reliance Netconnect+"
[4724] 06-01 20:01:56:315:
Before LoadPortsList2 in ReadEntryList()
[4724] 06-01 20:01:56:315: LoadPortsList2
[4724] 06-01 20:01:56:315: GetRasPorts
[4724] 06-01 20:01:56:315: RasPortEnum...
[4724] 06-01 20:01:56:315: RasPortEnum=603,c=10
[4724] 06-01 20:01:56:315: RasPortEnum...
[4724] 06-01 20:01:56:315: RasPortEnum=0,c=10
[4724] 06-01 20:01:56:315: RasGetDevConfig
[4724] 06-01 20:01:56:316: RasGetDevConfig=603
[4724] 06-01 20:01:56:316: RasGetDevConfig
[4724] 06-01 20:01:56:316: RasGetDevConfig=0
[4724] 06-01 20:01:56:316: SanitizeUnimodemBlob: mdm prot=0
[4724] 06-01 20:01:56:316: Port=COM17,fHw=0,fEc=0,bps=921600,fSp=0,prot=0
[4724] 06-01 20:01:56:316: StringCchCopy failed due to error 0x8007007a
[4724] 06-01 20:01:56:317: LoadPortsList=0
[4724] 06-01 20:01:56:317: successfully finished LoadPortsList2 in ReadEntryList()
[4724] 06-01 20:01:56:317: Reading media group "serial"
[4724] 06-01 20:01:56:317: New link format
[4724] 06-01 20:01:56:317:
DUPTEST:Port in this media
[4724] 06-01 20:01:56:317: Port=COM17
[4724] 06-01 20:01:56:317:
Trying to match the phonebook port in the system ports
[4724] 06-01 20:01:56:318: Port configured
[4724] 06-01 20:01:56:318: SetDefaultModemSettings(bps=921600)=1
[4724] 06-01 20:01:56:318: Reading device group "modem"
[4724] 06-01 20:01:56:318: Device List after deleting dupe
[4724] 06-01 20:01:56:318: StringCchCopy failed due to error 0x8007007a
[4724] 06-01 20:01:56:318: Fix entry type, 0 to 1
[4724] 06-01 20:01:56:318: Device List after deleting dupe
[4724] 06-01 20:01:56:318: ReadRasFile: ReadEntryList returned 0
[4724] 06-01 20:01:56:318: RASSQM: In ReadPhonebookFile Number of myuse profiles set 1
[4724] 06-01 20:01:56:318: ReadPhonebookFile returns 0
[4724] 06-01 20:01:56:318: RasGetAutodialAddressW
[4724] 06-01 20:01:56:318: RasGetAutodialAddressW
[4724] 06-01 20:01:56:318: DwEnumEntryDetails done. 0
[4724] 06-01 20:01:56:318: RasGetEntryPropertiesW
[4724] 06-01 20:01:56:318: IsRasmanServiceRunning=1
[4724] 06-01 20:01:56:318: IsRasmanServiceRunning=1
[4724] 06-01 20:01:56:318: GetPbkAndEntryName
[4724] 06-01 20:01:56:318: ReadPhonebookFileEx: called for pbk C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk, flags 8
[4724] 06-01 20:01:56:318: IsPublicPhonebook=0
[4724] 06-01 20:01:56:318: path=C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:56:318: full path=C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:56:318: IsVirtualizationNeeded: return value = 0
[4724] 06-01 20:01:56:319: ENTRY: Reading "Reliance Netconnect+"
[4724] 06-01 20:01:56:319:
Before LoadPortsList2 in ReadEntryList()
[4724] 06-01 20:01:56:319: LoadPortsList2
[4724] 06-01 20:01:56:319: GetRasPorts
[4724] 06-01 20:01:56:319: RasPortEnum...
[4724] 06-01 20:01:56:319: RasPortEnum=603,c=10
[4724] 06-01 20:01:56:319: RasPortEnum...
[4724] 06-01 20:01:56:319: RasPortEnum=0,c=10
[4724] 06-01 20:01:56:319: RasGetDevConfig
[4724] 06-01 20:01:56:320: RasGetDevConfig=603
[4724] 06-01 20:01:56:320: RasGetDevConfig
[4724] 06-01 20:01:56:320: RasGetDevConfig=0
[4724] 06-01 20:01:56:320: SanitizeUnimodemBlob: mdm prot=0
[4724] 06-01 20:01:56:320: Port=COM17,fHw=0,fEc=0,bps=921600,fSp=0,prot=0
[4724] 06-01 20:01:56:320: StringCchCopy failed due to error 0x8007007a
[4724] 06-01 20:01:56:322: LoadPortsList=0
[4724] 06-01 20:01:56:322: successfully finished LoadPortsList2 in ReadEntryList()
[4724] 06-01 20:01:56:322: Reading media group "serial"
[4724] 06-01 20:01:56:322: New link format
[4724] 06-01 20:01:56:322:
DUPTEST:Port in this media
[4724] 06-01 20:01:56:322: Port=COM17
[4724] 06-01 20:01:56:322:
Trying to match the phonebook port in the system ports
[4724] 06-01 20:01:56:322: Port configured
[4724] 06-01 20:01:56:322: SetDefaultModemSettings(bps=921600)=1
[4724] 06-01 20:01:56:322: Reading device group "modem"
[4724] 06-01 20:01:56:322: Device List after deleting dupe
[4724] 06-01 20:01:56:322: StringCchCopy failed due to error 0x8007007a
[4724] 06-01 20:01:56:322: Fix entry type, 0 to 1
[4724] 06-01 20:01:56:322: Device List after deleting dupe
[4724] 06-01 20:01:56:322: ReadRasFile: ReadEntryList returned 0
[4724] 06-01 20:01:56:322: RASSQM: In ReadPhonebookFile Number of myuse profiles set 1
[4724] 06-01 20:01:56:322: ReadPhonebookFile returns 0
[4724] 06-01 20:01:56:322: DuplicatePhoneNode
[4724] 06-01 20:01:56:322: GetPbkAndEntryName. rc=0x0
[4724] 06-01 20:01:56:322: GetInstalledProtocolsEx=0xc.
[4724] 06-01 20:01:57:690: DwEnumEntryDetails
[4724] 06-01 20:01:57:690: IsRasmanServiceRunning=1
[4724] 06-01 20:01:57:690: IsRasmanServiceRunning=1
[4724] 06-01 20:01:57:690: ReadPhonebookFileEx: called for pbk C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk, flags 8
[4724] 06-01 20:01:57:690: IsPublicPhonebook=1
[4724] 06-01 20:01:57:690: path=C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:690: full path=C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:690: IsVirtualizationNeeded: return value = 1
[4724] 06-01 20:01:57:690: GetLUAPhonebookPath: Return value 0 hiddenpbk path C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\_hiddenPbk\rasphone.pbk
[4724] 06-01 20:01:57:690: ReadRasFile: ReadEntryList returned 0
[4724] 06-01 20:01:57:690: SyncMasterPhonebookFile:++
[4724] 06-01 20:01:57:690: IsPublicPhonebook=1
[4724] 06-01 20:01:57:690: path=C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:690: full path=C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:690: FindFirstFile failed with 0x2
[4724] 06-01 20:01:57:690: ReadRasFile: File C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk does not exist
[4724] 06-01 20:01:57:690: DeleteEntriesOnlyInHiddenPhonebookFile ++
[4724] 06-01 20:01:57:690: WritePhonebookFile
[4724] 06-01 20:01:57:690: ModifyEntryList: Number of connections written 0
[4724] 06-01 20:01:57:690: RASSQM: In WritePhonebookFile Number of alluser profiles set 0
[4724] 06-01 20:01:57:690: DeleteEntriesOnlyInHiddenPhonebookFile : WritePhonebookFile failed with 0
[4724] 06-01 20:01:57:690: RASSQM: In ReadPhonebookFile Number of alluser profiles set 0
[4724] 06-01 20:01:57:690: ReadPhonebookFile returns 0
[4724] 06-01 20:01:57:691: IsRasmanServiceRunning=1
[4724] 06-01 20:01:57:691: IsRasmanServiceRunning=1
[4724] 06-01 20:01:57:691: ReadPhonebookFileEx: called for pbk C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk, flags 8
[4724] 06-01 20:01:57:691: IsPublicPhonebook=0
[4724] 06-01 20:01:57:691: path=C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:691: full path=C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:691: IsVirtualizationNeeded: return value = 0

Hi,
We could get more information about your problem through this log. While, for your problem, first of all, it would be better to contact USB Modem manufacture to confirm its compatibility with Windows edition.
After that, make sure its driver was upgraded to be latest.
Roger Lu
TechNet Community Support

Sql server 2012 express - tcp/ip connection to named instance using dynamic port not working

I have a named instance on a SQL 2012 Express server that won't connect via TCP/IP when wanting to connect off of the dynamic port. I can connect via shared memory locally on the server.   I can connect to the namespace when specifying the
dynamic port listed in the configuration manager.
This is the only named instance on the server and it is not the default.
TCP/IP is enabled
Allow Remote connections is enabled
the server browser service is running
I can connect via the dynamic port number
I am testing the connection locally on the server, so I don't believe a firewall is the issue. I get the same results if I test it from a remote computer.
When using the sqlcmd (sqlcmd -S tcp:SQLSRVR\NAMEINST -E) I get the message that "the requested protocol isn't supported [xfffffffff]".   The command (sqlcmd -S tcp:SQLSRVR\NAMEINST,59992 -E) works.
Through SSMS, I get the message "the connection was actively refused".
On other boxes, I can connect with the named instance without having to specify the port.
I have looked through the sql logs and nothing much shows up. The log does show that is listening on the port # for ipv4 and ipv6.   There is also a line in there talking about the SPN not being registered and not to worry about it if
you are not using Kerberos. I logged in through shared memory and it said I was using NTLM.
Any help would be appreciated.
thanks.

Hi clw,
I’m writing to follow up with you on this post. According to your description, I do a test, if you configure the database engine to listen on a specific TCP port (59992), and
the port is opened in the firewall. If you want to connect to the SQL Server instance, you 'd better to
use the port number.
In my opinion, by default, the default instance of the Database Engine uses port 1433, usually, if you have configured the server to listen on a non-default port number, when an instance of SQL Server uses dynamic port allocation, the connection string that
is built at the SQL Server client does not specify the destination TCP/IP port unless the user or the programmer explicitly specifies the port. Therefore, the SQL Server client library queries the server on UDP port 1434 to collect the information about the
destination instance of SQL Server.
If UDP port 1434 is disabled, the SQL Server client cannot dynamically determine the port of the named instance of SQL Server. Therefore, the SQL Server client may be unable to connect to the named instance of SQL Server. In this situation, the SQL Server
client must specify the dynamically allocated port where the named instance of SQL Server is listening.
For more information about configuring an instance of SQL Server to listen on a specific TCP port or dynamic port, you can review the following article.
https://support.transfrm.com/entries/503111-How-to-configure-an-instance-of-SQL-Server-to-listen-on-a-specific-TCP-port-or-dynamic-port
Thanks,
Sofiya Li
Sofiya Li
TechNet Community Support

CMS not configured yet.

Hi,
for first time we have installed NWDI(not much idea about NWDI configuration).when i open nwdi page (http://host:port/devinf) we are getting message "CMS not configured yet."in bottom.do we need to configure cms?and how to configure?

Hi John and Ervin,
while running di all in one wizard
i got errors like
1)Error: XPath evaluation error Step: Retrieve information for user configuration
2)Error: PASSWORD_TOO_SHORT
Step: Create Default Administration User
3)Error: PASSWORD_TOO_SHORT
Step: Create Default Development User
4)Error: USER_AUTH_FAILED: User account for logonid "NWDI_DEV" not found!
Step: Assign Development User to Group NWDI.Developers
5)Error: Unauthorized
Step: Upload Default ACL Settings
*6)Error: HTTP response "Unauthorized" from CMS server "http://host:50000/"***
**Step: Retrieve configuration information from CMS**
before running this wizard,do we need to do something,pls tell wat is exact procedure.
Regards

Roland UM-ONE CD-ROM does not mount on iMac OS 10.8.2 Roland driver for 10.8 installed as directed. No power ready light shows when connecting UM-ONE. System Profiler shows it, but not configured. Older UM-1X works fine. UM-ONE works on Dell Windows XP.

UM-ONE
Roland supplied CD-ROM does not mount or read by iMac OS 10.8.2, works with old TiBook and Dell laptop, however.
Got latest driver from RolandUS.com (um_1mx8d_v100), installed as directed.
No power ready light shows when connecting UM-ONE.
System Profile shows it there, but not configured.
With Audio MIDI Setup opened to MIDI Studio window, UM-ONE does not appear.
Tried many things without success. Tried swapping UM-1X (formerly on Dell laptop) with UM-ONE. UM-ONE installed and worked there without any issues. MIDI instrument communicates fine.
The UM-1X works without complaint and as expected when connected to any USB port on either the Dell or iMac, even a hub or keyboard port, just as it formerly had before changing operating systems, etc. It is old, but reliable.
Upshot is, for now, that UM-1X works with either the Dell or the iMac, but is currently attached to the iMac. UM-ONE (2011 model) only works with the Dell (Windows XP).

Same problem here! The only difference is that I'm using a MacBook pro 13 inch (2011)

I have a MacBook Pro and all of a sudden I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

I have a MacBook Pro and all of a sudden I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

BXB1905 wrote:
I tried the Apple diagnostics it did not work.
What do you mean it did not work! What were the results of the diagnostic tests?
Have you contacted your ISP to determine if the problem is on their end?
Have you changed your router channel? Sometimes this resolves wireless problems.
Your profile confirms you are using Lion. Check out the following:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
Configuring 802.1X in Mac OS X Lion and Later

Network Configuration Window Freezes When USB NDIS Internet Connection Sharing and Ethernet Port Are Used Simultaneously

Current Setup:
Asrock Extreme 4 Z77 mobo with built-in Broadcom NetLink (TM) Gigabit Ethernet. Windows 8 Pro. Intel i5-3570k (using onboard Intel 4000 HD Graphics). RAID0- 2 OCZ Vertex 4's.
I will refer to this setup as my tower.
The Ethernet port works fine by itself. When I use wired tethering with my Android phone (Droid 4 running on 4.0.4 Ice Cream Sandwich), it works fine when nothing is connected into the Ethernet port in the mobo.
The issue arises when I try to connect both simultaneously. The network configuration window in windows basically freezes and I cannot really navigate it without a ~60 second delay at best.
I would like to be able to accept the internet from my Android via a USB tether and either bridge the connection or use the internet connection sharing service to route traffic through the unused Ethernet port on the mobo (either to another computer/xbox
or more desirably a switch/router to spread to the entire home network). I have extensively researched the issue of Windows 8 become slow and unresponsive when I attempt to do this and I have not found anyone with the exact problem. I am able to
do both the MAC bridge miniport (bridge 2 connections) and Internet Connection Sharing though a Windows Vista (home premium) Laptop I have. The difference between the laptop and the tower I am try to do this on is the laptop has a WIFI and Ethernet connection
while the tower only has the on-board Ethernet.
Do I have all the necessary equipment to accomplish this, or do I need to buy a PCIe WIFI card? If so could I get away with just getting a USB WIFI dongle?
Any help would be very appreciated.

I had the same problem and came here by searching.
Per Rosengren's method solved the problem, but he didn't say how to do it, so I'll try to explain step-by-step for anyone that may venture here.
Open Device Manager (right click on Computer > Manage > on the left side, under System Tools choose Device Manager)
Choose the problematic device in Network Adapters (for me it's called HTC Remote NDIS based device)
Right click on it and choose Update Driver Software...
Click Browse my computer for driver software
Click Let me pick from a list of device drivers
Uncheck the box Show compatible hardware
For the manufacturer, choose Microsoft Corporation
Now you will have two options:
- Remote NDIS based Internet Sharing Device
- Remote NDIS Compatible Device
I chose the second one and it solved the problem, but if it doesn't work you could try the other one. In my case, the driver that was being used was neither of these, but a special driver from Android SDK ADT bundle.
Pick one and click Next. If a dialog comes up, confirm by clicking Yes.
Wait a few seconds for the connection to restart. If it doesn't work, try disabling and reenabling USB tethering on the phone, or reconnect the USB cable.
I should also note that I'm using a custom Android ROM on HTC Wildfire S (unofficial Cyanogenmod). If you have a stock ROM with HTC Sense, maybe this method may not work and you'll need a proprietary HTC driver.

Just did firm ware update on time capsule an now my airport express not connected do to air port utilities doesn't support base station ??

just did firm ware update on time capsule an now my airport express not connected do to air port utilities doesn't support base station ?

mickair wrote:
I have been experiencing some networking problems
Welcome to Apple's discussion groups.
I have the latest Time Capsule ("TC"), an old Airport Extreme Base Station ("AEBS") bought in 2007 and 2 Airport Expresses, one bought in 3 months ago ("AE-Alpha") and the other bought back in 2007 ("AE-Beta"). All of them have been updated with the latest firmware.
Based on those dates, the AirPort Extreme is probably flat (as opposed to dome-shaped), making it 802.11n-capable. The Newer AirPort Express is probably an 802.11n-capable model A1264, while the older one is probably a model A1084 or A1088.
I use {the TC's} DHCP function ... to avoid unauthorized use.
This a discussion for another thread, but that's not what DHCP is for.
The wireless setting for it is to participate as WDS Main, but after reading various posts, it seems WDS is a bad idea
With that older AirPort Express you're stuck with WDS unless you decide to replace it with a newer model.
The AEBS is currently setup as being a WDS Relay at the moment
Why a relay? That's only needed if there's another base station "beyond" it that is configured to depend on it.
Since the AEBS is connected to the TC via Ethernet, you should probably configure it as a "roaming network":
http://discussions.apple.com/thread.jspa?threadID=2273124
{The AE-Alpha} connects fine as WDS remote at the moment
I don't have any experience with mixed WDS and non-WDS networks, but since it's 802.11n-capable, you may be able to configure it to "extend" the network of the TC rather than as WDS. Look for a setting on the TC to "Allow this network to be extended".
Physical location:
AEBS in one end, TC and AE-Alpha in the middle while AE-Beta on the other end.
A device such as "AE-Beta" that's supposed to extend a network shouldn't be "at the end" but should be half way between the central base station and the clients that need an extended network.

Remote desktop connection not working in windows 7 Pro x64 bit sp1 3389 port not working

i have still facing same problem in last two week in my system RDC not working . i have installed in my system windows 7 x64 bit Pro sp1 then i check 3389 port working or not in my system use the command netstat -a -o command in
command prompt but this is my bad luck its not woking in my machine after i have decide to change RDC listening port via registry i have change it 3389 to 3391 after restart my system, and
after again testing using same command but no any change again rdc not listening . After i have search this issue on search engine google bing and microsoft , i have found more solutions but i have try one
uninstalled two microsoft updates first is kb KB2621440 second is KB2667402 and after again restart my system and again installed KB 2667402 But not change i have already enabled Remote Desktop connection in windows 7 and select the option
any version computer running , i have try three and four time enable disable remote desktop connection in my machine . but not change i have all windows firewall disable and uninstalled anti virus they intalled in my machine , and using the Mcafee
stinger tools to scan my machine to remove virus but stinger is not found any thread in system. ihave already run this command in my system sfc /scannow Please Can you help me to fix this issue.

Hi,
When you try to start the Remote Destop Connection, what errors it showed out?
Could the other PCs connect this PC with the RDC?
So you have read this blog?
RDP connections might fail due to a problem with KB2621440 - MS12-020
Did you reinstalled the KB2621440?
Besides, did you follow this guide to enable the RDC connection?
Connect to another computer using Remote Desktop Connection
And also this guide?
Why can’t I connect using Remote Desktop Connection?
Please take a check with those settings again.
Best regards
Michael Shao
TechNet Community Support

HT1595 My Apple TV 2 NOT connected to Ethernet, yet doesn't connect to wifi. HELP!

My Apple TV 2 is NOT connected through Ethernet, yet it keeps telling me: "To switch to wifi, disconnect the Ethernet cable from your Apple TV". Every time I restart or reset, it randomly works for a while and then displays the same message again.

You need a remote to setup the network in order for the remote app to be recognized.

Hi, I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand new a while ago i was trying to connect to my home wireless network it said that your airport is not configured then I restarted the system but it didn't restart it shows the "

Hi,
I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand-new (the 4th time to use the device) a while ago i was trying to connect to my home wireless network it said that the connection is timed out so i clicked the airport sign on the top it said that your airport is not configured then I restarted the system but it didn't restarted it showed the grey screen with the apple logo and the spinning wheel for more than 10min so I tried the force shutdown by pressing the power button till it switched off I waited for 5min then pressed the power button to start or boot the system and again the grey screen with the apple logo and the spinning wheel, I waited for more than 20min nothing changed, any solution please?
Your help is really appreciated"

Thanks a lot i followed the instructions for safe mode (i found out that i was pressing the C button after restarting) i did whats written there but the repair couldn't be performed so in addition i needed to re-formate the HD so i erased the volume and then repaired the disk--> quite disk utilities --> start the installation from the installation DVD.
Thanks really appreciating your help

6248 connected to 3750 yet ports not configured as trunkport

Similar Messages

Maybe you are looking for