6300 chargers with C2-01?

Will 6300 chargers (car and wall) work OK with a C2-01?  The plugs for my old 6300 and new C2-01 are the same, although one of the wall chargers for the 6300 puts out 5.5V whereas the charger that came with the C2-01 puts out 5.0V
Solved!
Go to Solution.

If you check the details under Sales Package Content for Nokia_6300 and Nokia_C2-01 the Charger is AC-3 in both the cases... so there should not be any problem..

Similar Messages

  • My iPad Air when charging cuts in and out, also the charger is extremely hot. Have tried different chargers with and power outlets, all with the same outcome.

    My iPad Air when charging cuts in and out, also the charger is extremely hot. Have tried different chargers with and power outlets, all with the same outcome.

    The troubling thing to me is the fact that the charger gets extremely hot - according to what you are saying. The charger can get warm and can get fairly warm when the iPad is charging, but it should never get extremely hot. Make an appointment at an Apple Store, take the iPad, the cable and the charger with you and ask them to look at everything for you.

  • Issues with using aftermarket 2G chargers with the iphone

    I was using my iphone 3GS last night and battery was over 90% I had just gotten done shooting some video and I was on my PC trying to figure what I needed to do to upload the video to YouTube. I pulled iPhone out of my pocket it was completely dead. I tried soft reset and hard reset with no luck. I thought maybe I had misread how charged the battery was and it had just died. When I got home I plugged it and let it charge overnight on an aftermarket charger. When I woke up this morning same thing. No power, no response( I tried plugging it into the wall and into the USB port of my laptop) I also tried soft reset and hard reset again this morning still no luck. I had been using an after market home charger that I had purchased with my original iPhone 2g. It seemed to work with no problems on the new phone and I had used it everynight for the last week or so.
    As a last resort I put my iPhone in a new case-mate charger/holster I had just purchased and finally it gives me the battery charging icon. My conclusion is that the after market charge I have will work OK for charging a low battery to full again but if the phone is completely dead then maybe only an original charger will work. The problem is I have USB cables and home charges and car chargers from my iPhone 2g and my iPod touch and I assumed they would all work and were interchangeable but now I am not so sure. I am also stumpped as to how my battery could say 90% and 2 hours latter the phone is compelty dead. The only things I had done was turn on location services ( I was messing around with an app I downloaded (Zillow) and used the camera for less than 5 minutes and made 2-3 calls. Maybe the case-mate holster charger I had used ealier in the day had given a false full charge, I am not really sure at this point I am still trying to sort out the issue.

    Apple changed the pin configuration with the 3G on phones ,ipod and itouch back in 2008
    They removed the firewire charge option new kit is now not compatible with older
    options that charge
    ie 3G or 3Gs for that matter will not charge on original Bose Sound dock or Apple
    docks for starters

  • Can I sync my 6300 calendar with Thunderbird/Light...

    Sorry if this is a stupid question.  I've just bought a bluetooth dongle for my PC and only yesterday connected my 6300 to computer and updated software etc for the first time.
    I'd love to be able to sync the calendar with Thunderbird/Lightning automatically as it connects.  Is this possible?
    And if so, is the sync two ways or just one way.  I have heaps of entries in the calendars on my work computer.  I'd love to be able to sync my phone while at work, then when I go home update my home computer's calendar from the phone's.  If that makes sense.

    A new problem is that Windows 7 does not use Windows Calendar so the simple solution from above that works for Vista doesn't work in Windows 7.
    These are the steps I took. It’s likely that not all steps are required. Sorry about the messed up formatting.....
    1.       Get Windows Calendar working on Windows 7.
    This is very straightforward. Follow the link below. Run it once to generate the .ics file
    (http://www.addictivetips.com/windows-tips/install-​windows-calendar-in-windows-7/)  
    2.       Tell Lightning to use Windows Calendar’s .ics file
    In Thunderbird, go to calendar view, right click on calendar listed on the left hand side and select properties….change its default file to point to your Windows Calendar File (C:\Users\name\AppData\Local\Microsoft\Windows Calendar\Calendars\Your Calendar.ics)
    3.       Uninstall software that may complicate things
    If they are installed, uninstall Nokia PC Suite, Nokia Ovi Suite and Microsoft Outlook.
    Make the following registry changes (messing with the registry can wreck your operating system. Don’t do it unless you know what you’re doing. I take no responsibility etc etc etc)
    Thanks to “Classic” on this german forum (and Google Translate) for this bit
    http://www.winfuture-forum.de/index.php?showtopic=​174635
    Open regedit.exe, navigate to Hkey Local Machine -> Software and add a new key called Windows Calendar. In that key add the following string values:
    http://www.winfuture-forum.de/index.php?s=c1afe722​9fa2613d26a1b82c604c879a&act=attach&type=post&id=3​...
    Reboot
    Install PC Suite (compatibility mode may help, I tried it a few different ways but in the end I don’t think it matters)
    6.       Tell PCSuite that its running on Vista
    Go back into the registry
    Navigate to HKEY_LOCAL_MACHINE\SOFTWARE\Classes\Nokia.PCSync.W​indows7PIM.ISynchAppU
    Create an exact replica of this key (including its contents) but call it HKEY_LOCAL_MACHINE\SOFTWARE\Classes\Nokia.PCSync.V​ISTAPIM.ISynchAppU
    (It’s likely that you could just rename Windows7PIM to VISTAPIM but I created the replica key)
    You should be good to go

  • 1G iPod chargers with 5G iPod?

    My original 5gig iPod recently died, which gave me a good excuse to get a 60gig video. I love this thing. Anyway, the new one only comes with the USB sync cable and no charger. I still have the Firewire AC adapter and a Firewire car charger for the original iPods. Fred Meyer has 6 pin Firewire to iPod dock adapters on sale right now. However, I've heard that the latest iPods no longer have Firewire connectivity. You can't sync with a Firewire cable. However, can I still charge with these old accessories and an adapter, or have the power requirements changed? I don't want to plug it in only to fry it. Will it charge properly with the 1G chargers?

    It will work, but the 5G ipod using the standard ipod plug vs thestandard firwire plug on the 1st gen ipod. You will need to get a firewire to ipod dock plug cable. Otherwise the ac unit will work.

  • 6300 trouble with updating.. phone won't turn on n...

    Hi guys, my dad got himself a 6300 a few months ago, and all was well until recently when the screen would randomly decide to go blank.. the phone would work, just the screen went blank.
    Today, he bought himself a second 6300, and me being the nosy person I am, I wanted to update the firmware (with the screen blank mind you!) to try and fix this problem.
    So halfway through updating, my dad's laptop freezes and the blue screen shows up. Now the phone is, put it this way, f#^$ed. It won't turn on or respond to anything I do. Would there be a way to fix this all?

    Yes, it must be properly flashed by flashing machine at Nokia Care Center in your area. It will be under warranty anyway.Message Edited by delixis on 20-Nov-200703:39 AM
    C6-00 with 8GB MicroSD

  • 6300 modem with Mac Leopard

    Has anyone had success with using a 6300 and a USB cable to connect to the internet with a Mac running OS X.5?
    The Nokia instructions seem to apply to Tiger OS X.4
    Many thanks

    HI, Chaplin
    this can have different reasons. The most likely is the following:
    when connecting, the provider hands out an ip address through the modem to the computer. This address usually stays valid during connection time, and for a given time after disconnection (typically orders of a few hours). Thus, when disconnecting the pc, one cannot immediately connect any other computer for this amount of time. Only after the time-out period it should be possible.
    using an airport express or similar thing allows you to connect more than one computer simultaneously. i think this might also be possible with other (non-wireless) devices, but i have no experience with this.
    Hope this helps
    Thomas

  • Problems with my 6300 paired with Sony Ericsson B/...

    I hope someone can help with this...
    When I pair my 6300 (firmware v.5.5) with my Sony Ericsson stereo Bluetooth headset (HBH-DS970) I get a message "Only Audio Files will be transferred."
    ONLY the music controls work! No phone audio or functions at ALL: no phone audio, the answer phone button does not work, and caller ID function doesn't work.
    Has anyone else had this problem, or know of a fix?
    Thanks

    The full retail install disks are available here and at any Apple Store and many computer retailers. Also, check the system requirements. Be sure your Mac has firewire and enough ram to run Tiger. At this point you might be able to find the disks at a slightly discounted price because of the coming release of 10.5 Leopard. But be sure it is the black disk, boxed version if possible.
    EDIT: And the install disc for Tiger is a DVD, so be sure your iMac has DVD.
    This may help to narrow down the model iMac you have.
    -mj
    [email protected]
    Message was edited by: macjack

  • Old chargers with new ipod

    can i use my old chargers (wall charger and car charger, which are ment for the old ipods, on my new ipod?

    Yes, you can.

  • Can I use my old iPhone 3G chargers with iPhone 4?

    Just want to know if I can utilize my old chargers? The iPhone 4 stuff resembles the iPad chargers. Thanks for the help.

    Thanks so much for the quick response.

  • New iPod Chargers with older generation iPods

    Hi,
    I have an older generation iPod (20GB, no click wheel) and recently lost my charger (one that had a firewire port on the charger itself).
    I went bought a new USB iPod charger and when I connect a USB cable with docking port to the charger and iPod (respectively), my iPod does not charge.
    Any ideas anyone?
    Thanks!

    If you have a 3rd gen iPod (the one with 4 buttons underneath the screen), then it does not charge via USB only firewire.
    You need to get the charger exchanged.
    Check here for confirmation on which iPod you have..
    http://docs.info.apple.com/article.html?artnum=60971

  • Is it safe to interchange my chargers with Apple products?

    I was wondering if you can use the iPad charger on the iPhone and vise versa?

    Kenny Fangue wrote:
    I was wondering if you can use the iPad charger on the iPhone...
    Yes.
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Kenny Fangue wrote:
    ... and vise versa?
    It will work... BUT it will be very Slow...

  • Manage messages with Nserie PC Suite

    I had a 6300 and the message manager I had (from the PC Suite) was something I really loved! I usually had my 6300 connected with my laptop via Bluetooth and I could receive, read, create and send text messages.
    The problem is, I haven't found a way to do so with my N78...
    Is there a way?
    6230 -> 6300 -> N78

    PC Suite doesn't support SIM card sms. You need to copy them to phone memory.
    What's the law of the jungle?

  • "Charging not supported with this accessory"

    I am a long-time Apple user, and feel like I know my way around the basics. I'm afraid I have a confusing/frustrating issue and don't seem to be alone. I have a third generation iPod touch. It's about 18 months old, and does not see heavy use. It used to connect, and charge, without any problem to a Logitech Pure-Fi Elite speaker system, an FM transmitter/charger I use in my car, and a couple of portable chargers with USB ports that I use for traveling in addition to my laptop. I recently acquired a new MacBook Pro running 10.6.8. To stop the constant iTunes upgrade requests, I went ahead and ran the update. Since then, I get the "Charging not supported..." sign, with every device, though I finally got it to connect to my laptop yesterday. It will no longer accept a charge through the Logitech system, and in fact stops sending music signals after half a song when docked, and will not play through the auxiliary output at all, though it will still play through headphones, at least the scrap that I did try in my attempt to troubleshoot it. It will not charge through the car system any longer. Either there is a terrible coincidence of software upgrade and hardware failure, or somehow the software is screwing up the processes that worked fine before. I have to say, Apple upgrades often seem like more trouble than they are worth. There is always something lost when these 'improvements' are made. I am not happy.

    I almost have exactly the same problem with the same iTouch generation/age.  But charging with normal Apple charging cables.  Would love an answer to this!  Thanks!

  • HP 6300 pro Multiple Monitor Issue

    Hello, 
    In office we are using 3 hp 6300 pro with 4 monitors for each. In each pc we have 2 output from graphic card, 1 from dvi and 1 from vga on board output to monitors. The problem is after the  every restart and normal starting process we can not see the screens  till unplug and plug the dvi cable (the screens are black till that). How can we solve this 
    Thanks 

    Hello  @melionh ,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I understand that you are having issues with your HP Compaq Pro 6300 Business PC displaying correctly on 4 monitors. I am sorry, but to get your issue more exposure, I would suggest posting it in the commercial forums, since this is a commercial product. You can do this at Business PCs - Compaq, Elite, Pro.
    I hope this helps. Thank you for posting on the HP Forums. Have a great day!
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Maybe you are looking for

  • Nokia N95 8GB takes ages refreshing even for one t...

    Hi All. I have had this REALLY frustrating problem... Every time i add a track to my phone, then i refresh it takes AGES to update the library. Does anyone know how to fix this? Nokia N97 Mini V: 10.0.020 : 14/10/09 RM-555 Old: N95 8GB : V 20.0.016 :

  • *HOW TO DELETE THE ARCHIVE LOGS ON THE STANDBY*

    HOW TO DELETE THE ARCHIVE LOGS ON THE STANDBY I have set the RMAN CONFIGURE ARCHIVELOG DELETION POLICY TO APPLIED ON STANDBY; on my physical standby server. My archivelog files are not deleted on standby. I have set the CONFIGURE ARCHIVELOG DELETION

  • Detected duplicate HTTP-based FlexSessions in CF10 with Air Mobile (3.4) IOS and Android apps

    We're getting the "duplicate session" error using Flash Remoting from Air 3.4 Mobile Apps ( IOS and Android ) with Coldfusion 10 Standard. faultCode:Server.Processing.DuplicateSessionDetected faultString:'Detected duplicate HTTP-based FlexSessions, g

  • Reset PO Output Via  Function Modules

    Hi, We are changing the PO after it is released and outputted, We are using the BAPI_PO_RESET_RELEASE to reset the PO to release and this fails because the PO is already outputted and entry exist in NACE, So is there any FM to revert back the NACE to

  • Building an Application

    Does anybody know when the next release of the Building an Application series by Dana Nourie is coming out?