6300 modem with Mac Leopard

Has anyone had success with using a 6300 and a USB cable to connect to the internet with a Mac running OS X.5?
The Nokia instructions seem to apply to Tiger OS X.4
Many thanks

HI, Chaplin
this can have different reasons. The most likely is the following:
when connecting, the provider hands out an ip address through the modem to the computer. This address usually stays valid during connection time, and for a given time after disconnection (typically orders of a few hours). Thus, when disconnecting the pc, one cannot immediately connect any other computer for this amount of time. Only after the time-out period it should be possible.
using an airport express or similar thing allows you to connect more than one computer simultaneously. i think this might also be possible with other (non-wireless) devices, but i have no experience with this.
Hope this helps
Thomas

Similar Messages

Anybody experience with Mac Leopard or Tiger on Equium A210-17I

Has anybody experience with Mac Leopard or Tiger on an AMD Toshiba? I read about some folks installing it on AMD and Intel and wondered how it could feel and work on an Equium. I have A210 17l.
Thanks for your input.

It seems to be that you are alone with this idea. If you will try it in the future please post a little bit about it.
Good luck!

Bluetooth modem with Mac OSX 10.5.x

I have been using bluetooth modem of E51 and N70 with Mac OSX 10.4.x, it has been working really fine.
Last week I updated Mac OSX to 10.5.2. iSync works well with Nokia_E51_1v1.dmg. But, bluetooth modem doesn't work well...
Actually I can connect internet with the modem script that is distributed at http://www.taniwha.org.uk/. But, after connecting, OSX said sooner that "The connection was terminated by the remote site. Please try again."
According to ppp.log, before connection terminated ppp.log records "Modem hangup"...
I am puzzled the problem. Please let me know how to do configuration to connect the internet with bluetooth modem on OSX 10.5.x

I compared the ppp.log in Tiger and in Leopard and I figured out that Leopard sent IPv6 packet after connecting the internet.
When such situation, we can apply "networksetup -setv6off Bluetooth" in console to solve the suddenly disconnection problem.
Now the bluetooth modem of E51 works really fine!
Sincerely,
chiro

How I set up an RS232 serial fax modem with Snow Leopard

A few times each year I need to send a fax. I don't have a fax machine.
My Macbook Pro does not have a phone input or built in modem but I have an old RS232 serial fax modem in perfect working order.
I purchased a Pluggable PL2303 USB to RS232 adapter.
Here is how to install a serial fax modem on a Mac running Snow Leopard using this adapter.
1. With the adapter disconnected, Install the Prolific driver for Snow Leopard found at http://plugable.com/drivers/prolific/
2. Plug the adapter into a USB port. You should get a window recognizing it and asking to set it up.
3. If you're not there, go to System Preferences and click on Network. In Network, click on "USB Serial Controller D". You will get a configuration section.
4. In the drop-down under configuration, click on "Add configuration". Name this configuration what you like. I named mine "fax modem".
5. Click on the "Advanced" button near the bottom of the configuration section. You will get a window with 5 tabs, labeled "Modem", "DNS", "WINS", "Proxies", and "PPP". Click on "Modem".
6. Fill in the modem fields "Vendor", "Model" and "Dial Mode" using the field drop downs. I found my Vendor, Zoom, in the drop down list but my model (56K faxmodem) was not in the Model drop down so I guessed and picked "Universal 115K".
I left the defaults - Dial Mode to "Wait for dial tone before dialing", Dialing to Tone and Sound to On, and "Enable error correction and compression in modem" checked.
Click OK. Click Apply. Close System Preferences.
7. Adding the fax to Printers and Faxes in System Preferences cannot be done the usual way, by clicking the + sign. Instead, the fax printer will be installed using the CUPS administrative tools as follows:
Open a browser and type "http://localhost:631/" (without the quotes) into the browser's address field.
This should bring up the CUPS (Common Unix Printing System) page.
8. Click on the "Administration" tab. Under "Printers", click on "Add Printer" and log in to CUPS as your system administrator.
You will get the "Add Printer" screen.
9. Under "Local Printers" select "Fax". Then click "Continue". You will get the URI screen with the word "fax" in the "Connection" field. Fill in the field so it looks like this:
fax://dev/cu.usbserial
Then click "Continue". You will get the name, description and location screen.
10. Fill in the fields as indicated. For name, I used "faxprinter". For Description, I entered "fax modem". For Location I entered "Serial Port". I left "Share this Printer" unchecked. When done, Click Continue. You will get the PPD screen.
11. Ignore the "Make" field. Next to "Or Provide a PPD File", click on "Choose File".
Navigate to boot disk (usually Macintosh HD)/ System / Library / Frameworks / ApplicationServices.framework / Versions / A / Frameworks / PrintCore.framework / Versions / A / Resources / and choose the file "Fax.ppd".
12. Click "Add Printer" and you are done.

Thanks for your detailled description of the faxmodem installation!
I've tried this with Mac OS X v10.8 Mountain Lion and it works fine.
I've to type "cupsctl WebInterface=yes" in terminal to see the interface.
Does anybody know, if send faxes are saved somewhere?

Modem with mac & PC

I am trying to share a cable modem with someone who has a PC. My sister doesn't have wireless internet, she uses a cable modem and a CAT5 cable. When I separate the CAT5 from her computer and try to plug in mine, I am unable to connect to the internet.
I'm able to plug her computer back in and get right on the internet, so I know it is not a 'power cycling' issue with the modem itself. And we've tried plugging in a friend's macbook and had the same results.
Is there any way around this problem? Of course I can just get online using my sister's computer, but there are times when it would just be faster to use my own.
TIA.

HI, Chaplin
this can have different reasons. The most likely is the following:
when connecting, the provider hands out an ip address through the modem to the computer. This address usually stays valid during connection time, and for a given time after disconnection (typically orders of a few hours). Thus, when disconnecting the pc, one cannot immediately connect any other computer for this amount of time. Only after the time-out period it should be possible.
using an airport express or similar thing allows you to connect more than one computer simultaneously. i think this might also be possible with other (non-wireless) devices, but i have no experience with this.
Hope this helps
Thomas

Firefox 3 unable to view mac hosting website with mac leopard.

I am unable to view images on this website using firefox? I reinstalled firefox and ran permissions under utilities. still no luck?
http://web.mac.com/rugged6769/Photos/Scuba_Class.html
Message was edited by: tommycai

There were many posts about this when FF3 was first released.
Firefox took a strict reading of the specs as far as when certain closing tags were required where Safari and FF2 are much "looser" about allowing certain constructs.
Or, the site works the same way using FF3 on any platform, not just Leopard.

CS3 crashes when opening or placing a file with Mac Leopard

I recently installed CS3 Design Premium to my iMac (OS = Leopard). I did the updates as well after installation.
I can start up Photoshop (Extended), and open up files from Bridge application but not from Photoshop itself. When I try to open a file, it crashes. I checked the forum, and find out one more instance like this (it was due to incomplete Version Cue installation). However, I followed up the technical doc but it still happens the same. I actually disabled Version Cue at the preferences but still no luck.
Any help, suggestion would be greatly appreciated.
Thank you.
Asli

I've not seen Word crash when selecting a smart folder - but it doesn't 'see' what's inside either. In other words when I select a smart folder in the file selector it appears to be an empty folder. And this isn't just a Word thing - lots of programs behave this way.
I use smart folders from the desktop. I have a folder in my Dock which contains all my smart folders. I open a smart folder from there and then double-click the document I want to open. It is a work around obviously but it works

USB STICK MODEM COMPATIBLE WITH MAC OS LION

Can someone help to recommend any compatible USD STICK MODEM with MAC OS LION?Thanks

Chance Harper wrote:
can someone please explain to me what type of modem I need to connect my mac pro directly to an ADSL connection account?
What USB Adsl Modems are there that are MAC OS X compatible? Can someone please hook me up with a list?
Why do you feel that you need a USB modem? I would think that you should be able to use a standard ADSL modem, connecting it to your phone line on one end and via Ethernet to your Mac Pro at the other end.

Are new Macs shipping with Snow Leopard?

If I order a new iMac today through the Apple store will it come with OSX 10.5 or 10.6 installed?
The Apple store says the iMac will ship with OSX 10.5 but they show a picture of the OSX 10.6 box set...
(I'd like to still get one with Leopard if I can)

Welcome to Apple Discussions!
PPP connections generally are done by dialup modem. Macs presently do not have built-in modems, though a USB modem is available to them from Apple, and some other vendors which do work with Mac OS X 10.6.
Any Mac though that can run Mac OS X 10.6, can also run any version of Windows. See the virtualization options here*:
http://www.macmaps.com/macosxnative.html#WINTEL
Boot Camp is included with 10.6.
By the way, MAC is an acronym for Media Access Control, a network naming convention. Mac is shorthand for Macintosh, the operating system and the machines made by Apple computer that run the operating system in question.
If you have further questions about Boot Camp or other virtualization see the Boot Camp category, and pick up of the forums inside of it at its header to be able to post your own topic:
http://discussions.apple.com/category.jspa?categoryID=237
- * Links to my pages may give me compensation.

WRT54GS with Mac OS 10.6.8 and RCN cable modem not working

Hello,
I have a Linksys WRT54GS, version 6 with Mac OS X (version 10.6.8) hooked up to a Scientific Atlantic cable modem, with RCN as the ISP.
Recently, RCN had some network issues, and so I had to power down and reset my modem. The modem is working fine now -- no problems at all when the Mac is connected direclty to the modem.
The router's network is OK in that I can connect the Mac wirelessly to the network, but I can't connect to the internet through the router (through neither the wireless or wired connection).
I have downloaded the latest firmware update for the router, following the Linksys site instructions, but this has not helped me solve the problem.
Does anyone have any advice as to what I should do? I did call Linksys tech support on the advice of RCN, and they said that the router does appear to be working (power, WLAN, and Internet lights are on), but they would be charging me nearly the cost of a new router to fix the problem.
Any advice would be appreciated!

Since you upgraded the Router WRT54GS with the latest firmware so once reset the Router and power cycle the whole network… Then connect the Modem with Linksys Router on the Internet Port and then connect any one computer to any one of the Ethernet port on the Router [Numbered – 1, 2, 3 and 4]… Let me know the RCN connection is a DSL connection or cable connection…
So if you have a DSL connection you can refer to this link:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=4020&userrole=Linksy...
So if you have a Cable Internet Connection you can refer to this link:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&vw=1&articleid=3686
As far as the wireless is concern:
# Open up the browser and on the address bar type 192.168.1.1 that will open up the Router setup page…
# Then Click on wireless Tab create the Wireless Network Name SSID and select the channel to 6, 9, and 11… Click Save Settings...
# Then Click on Wireless Security sub tab and select the security mode and provide the password as per the requirement… Click Save Settings...
After doing the settings try to connect the preferred network on the wireless devices and check the connectivity….

I have an imac with snow leopard. I do not have enough memory to get lion. I switched my mail to icloud and now my ipod touch has icloud. i can receive mail on my ipod touch and through the icloud web site, BUt I cannot receive mail on my mac directly

I have an imac with snow leopard. I do not have enough memory to get lion.
I switched my mail to icloud and now my ipod touch has icloud.
i can receive mail on my ipod touch and through the icloud web site, BUt I cannot receive mail on my mac directly any more. There is an exclamation point on my mail in box and also an ! on .mac.
Can anyone help me with settings so I can receive mail again directly on my mac?
Thanks
Mathmarv
<Edited by Host>

See this Apple note on troubleshooting icloud mail: http://support.apple.com/kb/TS4002
You may have seen this page already: http://www.apple.com/support/icloud/mail-notes/

I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have utility

I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have airprot utility app downloaded on my IPAD - it shows the modem and the internet no connected?

Do you mean an Airport Extreme Base Station connected to a Comcast Modem?

Moving accounts from Snow Leopard Macs to Mac mini with Snow Leopard Server

I got my brand spanking new Mac mini today with Snow Leopard Server! So far, we (at home) were managing our accounts on individual iMacs and a MacBook Pro. While I will be getting into the innards of account migration, management etc. I thought I'd post a quick question here; Currently I have an iMac with three user accounts on it (wife and two kids). I also have my own personal MacBook Pro with my account (the only Admin account) on it. We'll soon be getting another iMac for our daughter (who currently has an account on the existing iMac). My idea in getting the Mac mini was to move to and centrally manage all the user accounts in the household on the Mac mini server. What is the best way to accomplish this? What is the best way to move the existing accounts on to the server?
Additionally, I'll be looking into connecting the two stationary iMacs with Powerline Ethernet (where one runs Ethernet over existing electrical wires in the walls). My other option would be to rely on wireless network (I don't think this would be a good idea for if I am going to be placing the user accounts on the server and there needs to be a constant on, reliable connection between the server and the client computers as they will be talking to each other a lot!). Any thoughts on Powerline? (I am not looking forward to installing Ethernet cabling behind walls :o))
What say the wise men of Mactopia?!
Thanks,
Kenneth.
P.S. I had earlier accidentally posted this in the corresponding section of Mac OS X instead of the Mac OS X Server forum.

Ok so the esiest way to explain this is to tell you what i just went through.
I have 3 user accounts. All the accounts are network Users meaning that there home folder are kept on the server. I was having a problem with Time Machine giving me error 41 and error 11. After scratching my head for 2 days I ended up copying (Drag-n-Drop) the Home Folders to an External Hard Drive. I then proceeded to erase both of the internal hard drives on the mac mini and did a fresh local install of the Server OS.
Everything was fine at that point. Now this is where Snow Leopard stopped being nice.
I went and Created the user account again using WGM. I let WGW create the home folder and the 9 folder inside. I made sure the short names were the same and the passwords were the same as they were previously.
However, once i Copied files from the external drive to the home folders the permissions copied as well, Which i guess should be expected. So now at this point apparently the UID's of the newly created users wasn't the same as they were before the clean install. I have multiple instances of root listed in the ACL for several folders and also had several instances of System listed sporadically.
Now, This isn't to say that you can't drag n drop because now That I have it all squared away and everything is now working ok, I would probably still drag n drop the home folder off to an external disk, but only because I now know what to do to clean things up.
if you drag and drop be sure to use the CHOWN command and theCHMOD commands afterwards. Take a look at this MacFixIt article: http://reviews.cnet.com/8301-13727_7-20013630-263.html?tag=mncol;title
If you copy your local imac users to the home directory on the server you may want to follow the steps on the URL I gave plus you will most likely also have to do the following. In a nutshell you are going to use the chmod command to strip all the ACL Permissions then you are going to use the chown command to re-specify the correct owner and the correct permissions for the network user.
!) Go into ServerAdmin and click on Sharing
2) Go to the users folder you are using and select the user you are going to work with.
3) Click on the Permissions option
4) click on the +sign at the bottom (this will open the users & groups list to the right)
5) Drag the current user from the users list to the owner permissions line under posix section
5a) Click Save
6) Click on the Gear button at the bottom
7) Check the box for Owner Name and Owner Permissions.
8) Uncheck the box for Access Control List then click ok
Once you've gone through that rigmarole you can go back into ServerAdmin and fix the permissions for public and Sites folder which should only take a minute or so.
So the moral of this story and as I found out when i ended up calling Enterprise support is that the act of dragging and dropping user home directories from one server to another, or as in your case, from a local machine to a the server isn't anything that apple recommends or supports. you might want to read through the man pages for "Ditto" or so apple tells me, but honestly now that you know, the steps above aren't all that bad. It's true Knowing IS half the battle!
have Fun!
P.S. FWIW If you run into problems and have to call Enterprise Support be prepared for them to tell you to refer to the user Guides. So reading those would be to your advantage even though they aren't the easiest things to understand unlike apple's consumer products user guides

Mac Pro will not boot with Snow Leopard - need help!

I have had a lot of issues with Snow Leopard since I upgraded from 10.5.8. Most of my problems started after installing Office 2007. I finally wiped the hard drive and reinstalled everything. No problems until last week. Start up was taking longer and had to reboot a couple of times because of grey screen. So I would just put computer to sleep. Yesterday the computer was frozen on screen saver with scrambled rows of pixels on screen two and the main monitor had a frozen image.
I initially pulled all peripherals out and pulled the power plug for 5 minutes. I have left the peripherals out and pulled the second monitor as well. I tried pulling the power plug during a few more starts but nothing gets me to a complete start up screen.
I have tried resetting PRAM and VRAM and tried a safe boot. I tried booting from Snow Leopard and my Leopard disk stayed on either a blue or gray screen with spinning beach ball (on gray screen).
Put original install disk in and booted from using D to check the hardware. Good news is that the hardware test was OK. I did the extended test.
All different kind of start up problems.
- Some start with start up sound goes to Apple logo to blue screen to grey screen with beachball
- Some start ups with no initial sound then Apple logo to blue screen to grey screen with no cursor or beachball
- Some start ups with no sound to gray screen to blue screen to grey screen.
I have no problem wiping the HD1 again but I can't even get the OS disk to be recognized with holding the C key during start up. This last time it went to a blue screen (holding the C key) and a cursor.
I don't know what else to do - Please help!!!

There are lists (MacIntouch and MacFixit) of hardware / software support issues with 10.6. Accelerateyourmac is another place to watch.
There were some really long threads back in Sept about printer driver support.
The 7300 firmware was more about Windows support; those cards are failing and dropping like flies (how DO they know 3 yrs has expired anyway?) and they don't support SL features like OpenCL etc so I'd invest in ATI 4870, best graphic card and works in all models Mac Pro.
Lots and lots of bootable clones for backup. Never need to wipe and install again.

Can anyone please tell me which version of Photoshop Elements will download easily and run with mac 10.5.8 Snow Leopard?

I posted a question which was: Can anyone please tell me which version of Photoshop Elements will work with Mac 10.6.8 Snow Leopard. Then this window popped up saying mark this discussion with as a question and this window. I have no idea how this works. It already is a question and if I need to emphasize that, how does this window that looks like a Word editing window, help me do that?Downloading, Installing, Setting Up

You asked the question in the title area instead of the area where the body of your posting is intended to be. No fault of yours - they need to make the form clearer.
Check the system requirements for the various versions of Photoshop Elements and see which suits your system. Adobe only sells the most recent versions of their software, so if you need an older version you will need to find a vendor for it.
System requirements | Adobe Photoshop Elements

6300 modem with Mac Leopard

Similar Messages

Maybe you are looking for