64 bit LabVIEW FPGA 2009 driver for Xilinx SPARTAN 3E Starter Board

dear i need this module
we i install the module that i hava this appear to me
LabVIEW Support for Spartan-3E (incompatible with 64-bit platform)
is thier a version to supprt 64 bit???
best regards
hi ?Q>
Solved!
Go to Solution.

bad news
i will use Virtual machine to solve the problem
bet regads
hi ?Q>

Similar Messages

LabVIEW 2010 FPGA Driver for Xilinx SPARTAN 3E Starter Board

Dear Friends,
Is there any possibility to release a LabVIEW 2010 FPGA Driver for Xilinx SPARTAN 3E Starter Board?
Regards,
wedo
Solved!
Go to Solution.

Hi Brad,
So glad to get your post here!
I’m looking forward to download the new installer.
I wonder whether the new driver will support the 10/100 Ethernet Physical Layer Interface, since the last drivers aren’t support this feature!?
Also, will be any new examples included with the new driver? For instance: an example for the StartaFlash Memory; I have done an example for this but I couldn’t get it work! I don’t know why! You may check my post and the example in the following link!
http://forums.ni.com/t5/LabVIEW/Spartan-3E-StrataFlash-Memory-wrong-reading/m-p/1030898
By the way, is there any plane to develop a driver for the Spartan-3E (1600Kgate) kit? Both kits (500KGate and 1600KGate) have the sample on-board peripherals, the only difference is in the number of Gates (FPGA chip). I think all that is needed is to add the component ID (29597843---->3E1600) and revise the xc3s1600e.bsd and 3sXXXe.nph.
Thanks in advance & kindest regards,
wedo

LabVIEW FPGA driver for Xilinx SPARTAN 3E Starter Board

i need drivers for spartan 3E .

If you are at a university that has a site license for the FPGA module, the following might be of interest to you:
Using LabVIEW FPGA with the Xilinx SPARTAN-3E XUP Starter Kit
See also this discussion.
Quote from the license agreement:
...INSTALLATION AND USE OF THE LABVIEW FPGA TARGET MODULE FOR THE XILINX SPARTAN-3E STARTER BOARD (THE “TARGET MODULE”) IS LIMITED TO ACADEMIC INSTITUTIONS THAT HAVE A VALID, CURRENT “ACADEMIC TEACHING LICENSE” FROM NATIONAL INSTRUMENTS FOR THE LABVIEW FPGA MODULE. THIS TARGET MODULE MAY ONLY BE USED FOR INSTRUCTIONAL PURPOSES, SUBJECT TO THE TERMS AND CONDITIONS OF THE NATIONAL INSTRUMENTS SOFTWARE LICENSE AGREEMENT THAT ACCOMPANIES THE SOFTWARE...
LabVIEW Champion . Do more with less code and in less time .

Labview 6 compatible driver for HP89410A Vector Analyzer

Does anyone know where I can get a labview 6 compatible driver for an HP89410A Vectory Analyzer?
I have found labview 7 and labview 8 drivers for the hp894xx family of devices, however I cannot use them as I only have labview 6.
Barring a prewritten driver, how hard would it be to convert a labview 7 driver to make it compatible with labview 6?

The conversion is easy since there is a VI Tree VI in the driver. Since the driver was originally written in 1999 and has been up-converted to 7.0 and 8.0, saving it back down to 6.0 shouldn't be an issue.
Attachments:
hp89400_6.zip ‏1194 KB

Need 16-bit Merant dbase IV driver for Win 3.x

Hi all, I need a 16-bit Merant dbase IV driver for Win 3.x.
The driver was known as the Intersolv driver and now is a DataDirect driver but I can not find a download link for this driver anywhere.
I really need this driver to import/export some tree-rollup IDs from OFSA.
If anyone has this driver, please sent it to me at [email protected],
or at least provide information on where I can find it.
Any help will be appreciated!!!
Thanks in advance
vivpoly

The driver is needed for an import/export operation on an ORACLE product called OFSA, that is ORACLE FINANCIAL SERVICES APPLICATIONS. So I need the driver to export from an ORACLE database to a flat file and vice versa, so obviously oracle folks might be able to help, since they are the ones using/demanding this driver on their OFSA modules in the first place.
I know that Merant no longer supports the 16-bit driver and that I should obtain it from a local vendor, but this will be time consuming and I am in urgent need of the driver. Some oracle developers might have it!

Need a 32-bit windows home server driver for a cp2025 printer

I have a Windows Home Server 2011, and multiple Windows XP workstations. I need an XP driver for a CP2025DN printer that I can load onto the WHS 2011, as I want to configure the WHS as a Print Server. The WHS does not recognize (like) the HP Universal drivers, and I do not want to use the Express install download packages. All I need is a driver, like we used to be able to download.
Anyone have any suggestions/hints?

those may be helpful...
http://social.technet.microsoft.com/Forums/en-US/a129f49a-0216-41f0-b190-3efb46fbb8ac/generic-text-only-driver-on-windows-2008-server-r2?forum=winserverprint
http://blogs.technet.com/b/yongrhee/archive/2009/09/14/how-to-add-64-bit-print-drivers-on-32-bit-windows-server-2003-or-windows-server-2008-print-server.aspx
Best,
Howtodo

Going from xp to windows 7 64 bit using an external drive for music storage

Greetings Techies!
I hope you all are well.
I need to move my iTunes from an XP machine to Windows 7 64 bit. On the XP machine I am using an external drive for music storage and the iTunes database is stored on the internal drive. I am looking for advice on how to transfer all of this over to my new Windows 7 64 bit machine. I know iTunes can be picky about everything and I don’t want to take and chances and loose my playlists or music.
Any help would be much appreciated.
Blessings,
paul

You are right about it being picky. I just upgraded from Vista to Windows 7 and was forced to format my drive. I had all the music backed up, but when I imported it, I have 2 or 3 copies of some songs, art work missing, and have lost my playlists. I hope someone responds to your question, because I could use similar help! Best of luck to ya . . .

LabVIEW FPGA PMW modulation for L298n H-bridge

Hello to everyone,
I am new in LabVIEW FPGA programing and I have a couple questions, so I would be grateful if you could answer me. For my final work I have to control the speed and direction of DC motor using sb-RIO 9636 and H-bridge L298n. In attachments you can find scheme of the H- bridge and my program. I have conected In1(pin 5 of L298n) to digital pin 1 of the card, In2(pin 7 of L298n) to digital pin 2 of the card and changing the state of the pin I change the direction of the motor(I know that the one In should be Low and the other High so the motor can rotate in one or the other direction). PWM(Enable pin of the L298n pin 6) I have conected to DIO3.
PWM signal I cretaed is shown in picture.
My questions are:
1.Will loop timer I used, provide that period of signal is lenght I specify in the control(for example if I put 20 000 will the period be 20000 s)?
2. Can I vary the duty cycle changing the control Waiting (DIO3 is HIGH for a couple of us, then it sets LOW, and then all that repeats )?
3. Earlier I thaugt that PWM signal I should send in both IN1 and IN2, and that the Enable pin is used to stop or start the motor. I tried that and the motor was rotating different speed, and I could stop or star the motor with enable pin, sending it HIGH OR LOW, but I could not change the direction of the motor. So my other option was to conect the pins as I explained at the begining. My question is: Should I PWM conect to the enable pin, and will thah work?
Thank you

I found a couple of resources that deal with PWM on the FPGA and motor control - they might be helpful to reference as you look for answers to your questions.
Developing a PWM Interface using LabVIEW FPGA
http://www.ni.com/white-paper/3254/en/
CompactRIO Motor Control Basics Tutorial
http://www.ni.com/pdf/labview/us/compactrio_motor_control_basics.pdf
PWM Output With LabVIEW FPGA
http://www.ni.com/example/26499/en/

Labview 5.1 driver for HP3437A

Hi,
does anyone have a driver for a HP3437A for labview 5.1?
On the ni homepage are only drivers for labview 6.0 and 7.0 available.
Thanks, Niko

Here it is. Not much of a driver - only one VI and there's no error checking.
Attachments:
hp3437a.zip ‏32 KB

Need Win-7 (32 bit) Intel HD Graphics driver for HP 14-d008tu Notebook

I have got the driver of Intel HD Graphics for Win-7 (64 bit) and now the HP Support and Drivers!
BUt I need display driver for Win-7 (32 bit).
Please let me know how can I get this driver?
if you need more description, then pleae let me know.
Thanks.
This question was solved.
View Solution.

Hi:
This 32 bit Intel graphics driver should work...
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23884&lang=eng&ProdId=3719

Need help finding a driver for our NI A/D board

My A/D board has the following numbers: 70243 and 84-01 and 3199F. Help me find the driver

All of the NI drivers can be located on the NI Drivers and Updates page. In order to find the required driver, you will need to know what the device is called. You can find this information in several different ways. One way is to visually inspect the device. If it is an NI device then it should list the device name somewhere on the board. Also, you could locate the part number. This number usually ends in -01 or -02 and is printed near a bar code. If you can find this number, then simply type it into the search on ni.com to locate the name of the device.
When the name of the device is figured out, you should then determine the appropriate driver for the device from the Drivers and Update page linked above.
If it is not an NI device, then you will want to view the device manufacturer's webpage for available drivers.
Please do not post back to this message as I do not believe the message pertains to the NI Measure software. The question is more related to a specific piece of hardware. Thus, you should repost this question, if another exists, to the appropriate NI Hardware category.
Best of luck.
Jared A

Nigpib-linux-0.6 GPIB software driver for Linux and PXI GPIB board

My I use nigpib-linux-0.6 GPIB software driver for Linux in a Compact PCI system running linux and equipped with your PXI GPIB board ?
Thanks.
Paolo Santinelli.
[email protected]

If you alter the device ID of the device from c801 to c821 within the driver module, you should be able to use the driver with the PXI board.

Packet or Ndis2 driver for Onboard Lan on K7N2 boards

I need a Packet or Ndis2 driver for Onboard Lan on K7N2 based boards, in order to run Norton Ghost disk image program across my network. Does anyone know where I can get such driver?

I need a Packet or Ndis2 driver for Onboard Lan on K7N2 based boards, in order to run Norton Ghost disk image program across my network. Does anyone know where I can get such driver?

Is it Possible to interface LABVIEW FPGA Module with Xilinx Spartan 3A Starter Kit

CAn anybody suggest me >>>>>>>>>>

We currently only support the Xilinx 3E XUP 500 based board (and only for academic purposes) in terms of non-NI FPGA hardware.

Lookout driver for NI PCI Timer/Counter Board NI-6601

Is there any Lookout version 5.0 driver available for the NI-6601 PCI Card? Any built in drive that works?

There is a PCI card available that works with DAQ OPC, in this case the E-series product line would apply. Many of the PCI-6040E type cards have counters. However, at this stage of development I would recommend for serious consideration using LabVIEW and NI-DAQ. Lookout is a great program for communicating with OPC items. However, for basic to advanced data acquisition, LabVIEW is the optimized solution. All other ways will require more development time.
Regards,
Robert Jackson
Application Engineer

64 bit LabVIEW FPGA 2009 driver for Xilinx SPARTAN 3E Starter Board

Similar Messages

Maybe you are looking for