645 Ultra not booting with new GeforceFX5200

Thanks ahead of time for all the help.. I'm really just a newbie computer guy with a frustrating problem. Before last week I was running my system with a Geforce2MX with no problems. At one point I had to flash the motherboard because it didn't recognize my hard drives, but the video card was fine. I bought Deus Ex Invisible war, and found out I had to update my video card. So I purchased an Albatron Gigi GeforceFX5200E. After removing my old video card and inserting the new one, my computer would not boot. The power would turn on, but the Monitor does not. The D-Bracket says it is hanging on "Initializing Video Interface", so I had my friend test out the video card, with the results being it works perfect. So I am at my wits end... I have the new AGP drivers... the motherboard is updated... I know the card works. I have read about messing with the voltage or somthing, but I don't know how or what to set things at. Please help!!!
My specs:
MSI 645 Ultra Motherboard (flashed to latest version)
Celeron 2.4ghz processor
512mb RAM
CWT 350w Power Supply:
3.3v - 20a
5v - 35a
12v - 15a
Soundblaster Live! Value
Memorex CDR/W drive
56k Modem
2 WD Hard Drives (80/30gigs)
Fan Control Unit w/ 4 Fans
I hope thats enough info. I'm very close to just ditching the motherboard for somthing else, its been giving me so many problems. Thanks again.....

What would you all recommend for a new power supply? What should I look for? Somthing relatively inexpensive (starving musician here) that gets the job done would be great.
Also, I flashed the motherboard before buying the new troublesome videocard, because my motherboard wasn't recognizing my two WD hard drives I purchased, but it was working fine with these small older hard drives. Weird stuff... other then that though the motherboard has been good... especially if this video card stuff is simply a power issue. Thanks again guys.

Similar Messages

T410 will not boot with new SSD

I've cloned my HDD to a new SSD, but it will not boot. It goes into a Lenovo Think Bios splash screen / Black screen loop. I booted off a repair disk and performed a repair, but it is still doing the bios loop thing. This has happened with both an OCZ and a Kingston SSD. Any ideas? Thanks...
Solved!
Go to Solution.

I'm going to venture a guess that the drive was not cloned properly.
The "new" drive must be in the machine's HDD bay, and the "old" one in the USB enclosure.
I always use Clonezilla for the rare occasions that I actually clone something, but Acronis should do just fine as well.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Will not boot with new hard drive

I used a SATA drive with adaptor as a boot drive in an MDD for most of the past year. I just got a MacPro 5,1 and wanted to use this SATA drive as a data drive in the new computer. I pulled it out of the MDD and put it in the MacPro. On start up I get the message You need to hold the power button or press restart. Since it has a boot volume I thought this might be a problem. I held down the Option key during start up to select a boot drive. Here it shows both the this drive and the OEM MacPro drive. Which ever I select I still get the error message. I can put this back in the MDD and get the same error even though it shows up as a boot volume when holding the Option Key. This drive does not seem to be totally dead since it can be seen during start up but it wont let the computer finish booting. It gets to the Apple logo but no farther. Can I salvage this drive? Data on it is unimportant.

You really need to use FW case; reformat the drive to use GPT partition table.
When booting the system's EFI polls all drives to look for valid system paths and to see which is blessed. A corrupt directory can even prevent booting from any drive or DVD.
I tell G5 owners to reformat as soon as possible once data is recovered, even though if they were running 10.5.8 their SATA drive may be okay.
Nuke the drive one way or another, I'd assume you have a spare FW case. And try booting from OS X DVD - you can install a fresh OS as backup/emergency system drive.
Any new SATA II or III drive are fine, WD Black are popular and 640 $69 or 1TB $89.
Have fun, I went from G4 MDD to Mac Pro over 4 yrs ago and it is still running strong -- and quiet!

IMac G5 ALS not booting with new power supply and perfect capacitors

Hey guys. Just got this beauty yesterday for cheap. Came with the box, 2 of 4 Styrofoam inserts, the manual, the power cord, and the keyboard.
I was told it has a brand new power supply. When I plug it in, LED #1 on the motherboard comes to life. pressing the power button does nothing. I have tried everything: blowing out any dust, reseating all connectors, booting without RAM, adding a hard drive (did not have one), removing the optical drive, modem, and BT/ap card. The only sign of life is when I press the internal power button, and the light flickers. This is promising.
I did notice when it is plugged in, there is a high pitched whine coming from where the LED is. I hope this is not causing the problem.
All capacitors are perfect, and not burst or leaking. I had a 1.25ghz eMac with bad caps, so I know what they look like.
I removed the motherboard, and there is no sign of any fried component on either side. It looks like a brand new machine basically.
I was thinking of just getting another good logic board for it, as they are cheap, or ask a friend to recap the board anyway.
Anyone here know what could be wrong with it? I hope I did not just waste money on this. It was relitively cheap though.
Specs:
iMac G5 Revision B Ambiant Light Sensor model
1.8ghz G5
512mb of RAM
combo drive
no HD (had 160gb originally)
airport/bluetooth combo card

Hey Lam,
The only sign of life is when I press the internal power button, and the light flickers. This is promising.
I did notice when it is plugged in, there is a high pitched whine coming from where the LED is. I hope this is not causing the problem.
I'm with Miriam on this one. That "new" supply sounds bad. Look very carefully inside the power supply (through the little perforations in the case) I'll bet you see caps w/ the same domed tops like you've seen before. That whine is also a symptom of a bad PSU. It's not even strong enough to power the soft start.
I've seen 2 20" and 3 17"ers recently. Replaced caps on 3 of the PSUs and got one to work on a 17" that belonged to a teacher so that went back. Swapped the working PSU from one of the 20s w/ a bad GPU into the one w/ a bad PSU. It's working but in a place where I can keep an eye on it since I don't trust it since the caps don't look good.
I've done this hack:
http://gallery.me.com/iamkimc#100033&view=grid&bgcolor=black&sel=12
and can get all the iMacs to work that way. Advantage - cheap, totals 1/3 or the replacement Apple part (used). Con - boxes outside the nice iMac case.
The auto laptop supply loads the Sparkle down too much for the 20" however. I'm working on finding an auto supply that saps less Amps or a simple voltage doubler for the 12V supply to solve that problem.
The ATX hack is pretty simple and only requires switching two 12V leads. Oddly one of the early versions of the 17"ers ran fine without the 20V inverter power. Go figure.
Richard

Pxie 8108 does not boot with new hard disk

Hi
I'm currently using PXIe 8108 with PXIe-1062Q.
The previous hard disk was borken so I had to install a new hard disk.
The new hard disk is fommatted as NTFS format, and it is currently mounted on 8108.
Unfortunately I don't have recovery disk avaialble so I'm trying to install Windows 7 on empty hard disk.
When you boot, the PWK OK LED light is on all the time, DRIVE orange LED is on for few seconds only when I turn the switch on.
Labview RT switches are all off, I cleared CMOS many times from the board but, the screen shows nothing.
I have tried use my DVI monitor with other device as well, and it worked so there is no problem with the monitor.
In addition, I tried to go to window safe mode by pressing F8 or Del it didn't work, so I see nothing on the screen when its booted up.
I tried to put as much information I can it will be very appreciated if you can help me with this issue please.

You said you can't get into Windows safe mode, have you installed Windows on the hard drive? Are you able to get into the BIOS for the controller?
If you aren't able to access the BIOS for the controller, it may be due to bad RAM. If you are comfortable installing RAM and you have some extra laptop RAM of the same type (I think it's DDR3 for your controller) laying around, you can try swapping out the RAM.
Was your hard drive damaged through some event, or did it just stop working?
AC - LV Solver

MacBook Pro won't boot with new hard drive, but a different MacBook Pro will

So here are the details. My friend and I both have 13-inch Mid 2010 MacBook Pro's. Same processor and specs since they were purchased at the same time, but originally had 250 GB hard drives. His hard drive failed and needed a new one. Put a 500 GB Seagate Momentus 5400.6 in his computer, and tried using a flash drive with "Install OS X Mavericks" on it to install Mavericks on his new hard drive. No matter what, it wouldn't install. I finally was able to install OS X 10.9.4 on it by connecting the new hard drive to my computer with a USB hard drive enclosure. I put the hard drive back inside his computer and it wouldn't boot (stuck on the gray screen with apple logo and a spinning wheel). I then attached to the hard drive to his computer externally with the USB enclosure, and then it booted and worked perfectly.
So, it seemed like the problem was with something inside his computer, but then I switched our drives, and that doesn't seem to be the case anymore. I put my original hard drive into his computer, and his new hard drive into my computer, and they both booted and worked perfectly, so I have no idea why his computer will not boot with the new hard drive internally.
To summarize, his computer boots with: 1) new hard drive connected externally (won't work if it's internal), and 2) my hard drive internally
but my computer boots with: 1) new hard drive connected externally AND internally, and 2) my hard drive internally.
Both hard drives have OS X 10.9.4 installed
If anyone has any idea what's causing this and how to make his computer work with the new hard drive internally that would be greatly appreciated.

So after switching the internal SATA cables from each computer, now we have
His computer, with my SATA cable:
1) Worked with every hard drive!
My computer, with his SATA cable:
1) Works with 1 TB Toshiba hard drive
2) Works with 500 GB Seagate hard drive
3) Works with my original hard drive
4) Flashing folder with question mark with his old hard drive
So it turns out you were right! Definitely had something to do with the SATA cables. But it's still strange that mine was able to boot with all the hard drives except the one that was originally in his. So it seems like it was some combination of his SATA cable and something else, since when his SATA cable was in his computer only 1 hard drive (my original) worked, and when it was in my computer, 3 hard drives worked. But at least its working, and I'm just gonna keep our SATA cables switched since that seems to work out fine

T43 – Model 1871-FU1: Will not boot with blank screen. Only Fan is running. Any ideas?

T43 – Model 1871-FU1: Will not boot with blank screen. Only Fan is running. Any ideas?
Solved!
Go to Solution.

What lead_org is referring to is commonly known as "re-balling" which involves unsoldering the Southbridge chip from the planar, replacing all (6-700) solder balls with new ones and then re-attaching it under heat/pressure.
This is the place that you need:
http://www.theboardroom.info/index.html
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

HP G62 Will Not Boot With Power Cord Plugged In

I have an HP G62 laptop that is about four years old. I've had a couple of problems with it before that were resolved relatively satisfactorily, however five or six months ago I started having a new issue. The laptop will not boot with the charging cord plugged in, whether there is a battery in it or not. Nor will it return from sleep mode (screen black, status light on the power button flashing) with the charging cord plugged in, whether there is a battery in it or not. It simply shuts down and I end up with an error screen the next time I boot up. I have tried other charging cords and it has been the same, however the cord will still charge the battery. This means I have to charge the battery, unplug the cord, boot up the computer. This annoyance is worsened by the fact that the battery is old and unable to hold charge for very long at all and I fear one day even the battery won't be enough to boot the computer.Can I fix the power cord issue? Should I buy a new battery? Or let my computer give up the ghost and scrounge for a new one? Any help would be greatly appreciated.

the charger input could possibly need replaced and/or the charger

Cannot boot with new SSD

Installed new OWC 240G SSD in 2007 iMac. Started up with old HD in external case running OS 10.10.2. Initialized SSD with Disk Utilities, and it mounted on the desktop. Transferred contents from old HD to new SSD. Computer boots fine from old HD in external case, but does not boot with internal SSD. After displaying Apple symbol for a few seconds of the startup process, computer goes to a kernel panic and gets into a loop of retry message-Apple symbol-message-etc. The SSD shows on the desktop, but does not show as a startup disk in System Preferences pane. Disk Utilities shows drive is fine, but repair of permissions is grayed out. Window says permissions repair is only permitted on OS installed with an Apple installer. System folder on the SSD does not show the "blessed" symbol. Have tried recloning using Time Machine backup - same result. Installed eDrive on SSD with TechToolsPro, and can start up in eDrive thru TTP window, thus verifying all cabling. After booting with original internal HD installed in external case, SSD will show on desktop, but will disappear in a few minutes after a message says it was improperly ejected. Suggestions? Is there a way to access OS 10 software purchased and downloaded from Apple site?

Many possibilities here. Maybe a bad connection when you installed the drive. Maybe a bad drive. Maybe a bad SATA cable.
How did you format the drive? Should be Mac OS Extended Journaled. When you boot into the recovery drive, access disk utility from there and see if you can access the drive.
I have the same drive as you. What I did is use Disk Utility from the recovery drive of TM. I first re-formatted the SSD drive. Then I used Disk Utility to restore the whole drive of my original to the new SSD drive.
You can still download the Yosemite installer from the App Store in your purchases providing you downloaded it from the App Store already.

2960X-48FPS-L does not boot with IOS 15.2-2E

Hello,
i got a bunch of 2960X switches. But some of them do not boot with the new IOS Version. The older 15.0-2 EX do boot.
Does anybody have a clue why this happens? During the Bootprocess it just stops to load:
File "flash:/c2960x-universalk9-mz.152-2.E.bin" uncompressed and installed, entry poin0x3000
executing...
Loading "flash:/c2960x-universalk9-m
Thank you for your help.

On the ones that cannot boot 15.2(2)E, can you break the boot cycle using the "Mode" button?
If the answer is "yes", then try the following:
1. Copy the IOS BIN file from a working switch to a USB flash drive;
2. In ROMmon, force the switch to boot the IOS from your USB flash drive;
3. If it does not work, try a different IOS, like the EX3 for instance. Try the same process, boot the BIN from your USB flash drive.
4. If it works, try a different IOS, like EX3, for instance. Downgrade the IOS from 15.2(2)E to EX3 and see if the switch can boot normally.
This exercise will determine where the fault is coming from: IOS bug or a hardware batch problem.
To determine if you'e got a hardware batch problem, you may need to look at the serial number of the switches working and not working. From left to right, look at the 4th, 5th, 6th and 7th numerals. This will determine the year and month your appliances were made.

ThinkCentre M93p not booting with WD MyBook USB 3.0 drive

Hi!
I have a serious problem as boot freezes on my ThinkCentre M93p Tower at the Lenovo logo when the Western Digital MyBook USB 3.0 drive is attached at boot time. I have already commented on this in this thread:
http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T420-Not-booting-with-3TB-external-USB3-dri...
It seems to be an UEFI / BIOS problem and I hope that there will be a resolution soon, as I like the Lenovo ThinkCentres and would like to buy more for our company. This problem seems to be present on Lenovo notebooks and desktops when looking at other posts here.
Regards,
Anguel

jvandeven wrote:
This bug has been driving me mad since I received my P900 Thinkstation - as PeaB0dy notes, the hardware is great but the software (pretty much in general) is really disappointing.
Have you actually opened a support ticket with Lenovo?
I had a problem with my M93p SFF relating to an older external USB drive from Seagate, and an apparent incompatibility with management of the drive across soft reboots. I opened a support ticket and got superb results from Lenovo engineering over the next few months. I sent them the drive to have (as I had no use for it, replacing it with a new Verbatim USB drive which was fully 100% compatible with the machine and saw none of the problems I saw with the Seagate drive).
The eventual outcome was a public fix in a new version of the BIOS to handle the unique characteristics of the Seagate drive.
So, have you actually opened a ticket with Lenovo? They need to have something official to start from when new problems are discovered. The M93 machines are "new", so issues of compatibility is not a surprise to me. Especially when UEFI, GPT, large drives >2GB, and Windows 8 are concerned.
[I'm still staying with Win7 Pro x64 for now.]

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed?

Flash player does not work with new ICS Android 4.0.4 OS. Has this problem been addressed? I am using Firefox Beta for android and I also tried just Firefox.

Please check the Play Store app for any Flash updates and install them if present.

Home sharing does not work with new mountain lion update.

home sharing does not work with new mountain lion update. Does anyone else have the same issue. Updated all computers in my home, deauthorized and reauthorized each computer. turn off home sharing and turned it back on. don't know what else to do..please help...

Our Apple TVs continue to lose connection ever since installing Mountain Lion on the host computer. The only thing that fixes them is to quit and relaunch iTunes, which only works unti the ATV goes to sleep. If a movie is paused for more than a few minutes and the ATV goes to sleep, pressing play again on the remote is greeted with "There are no movies on this computer" or "Turn on Home Sharing."
If we stop a video on one ATV and attempt to resume it in another room, the error begins again. The other ATV can't connect until iTunes is relaunched.
My guess is that it has something to do with the new [annoying] security settings. But I still haven't found a fix other than restarting iTunes everytime we want to watch something from our downloads. Fail.

My ipod 5.1.1 (9B206) will not sync with new Itunes version 12.0.1.26. Can anyone help

My ipod touch 3rd generation OS 5.1.1 (9B206) will not sync with new Itunes version 12.0.1.26. Can anyone help

What exactly happens when you try to sync?
Does iTunes see the iPod?
Was the iPod previous synced to another iTunes library/computer?
Have you successfully synced from this iTunes library/computer before?
If so have you done anything like update iTunes on the computer since it last successfully synced?
Do the songs play in iTunes?
Does any media now sync to the iPod?
Do you have the right boxes checked to sync?
iTunes: Syncing media content to iOS devices and iPod
Try syncing using the manual method
Managing content manually on iPhone, iPad, and iPod
If iTunes does not see the iPod:
iOS: Device not recognized in iTunes for Mac OS X
Or
See
iOS: Device not recognized in iTunes for Windows
- I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
- Then do the other actions of:
iOS: Device not recognized in iTunes for Windows
paying special attention to item #5
- New cable and different USB port
- Run this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Also see:
iPod not recognised by windows iTunes
Troubleshooting issues with iTunes for Windows updates
- Try on another computer to help determine if computer or iPod problem

I downloaded latest software on iphone 4 and installed new software on my imac (snow leopard 8.6 and now phone not synching with new itunes. Itunes does recognize the phone but the itunes is totally different now. It doesn't look anything like the previou

I downloaded latest software on iphone 4 and installed new software on my imac (snow leopard 8.6)and now phone not synching with new itunes. Itunes does recognize the phone but the itunes is totally different now. It doesn't look anything like the previous vesions. I can't even find a tab for synching. very strange. any help is appriciated.

iTunes 10.7 is compatible with Snow Leopard.
You can download it here: http://www.apple.com/itunes/

645 Ultra not booting with new GeforceFX5200

Similar Messages

Maybe you are looking for