648 Max no booting (all leds are RED)

Hello,
I use my 648 Max mother board for 2 year with :
- P4 @ 2,4 Ghz
- two PC2700 DDR 512 Mo
- the D-Bracket 2
- two hard disk
- a nvidia g-force 2
- a lan pci
- sound blaster live! 5.1
Since yesterday, my computer don't start (whithout hardware change) : All D-Bracket 2 LEDs are red.
Is just a mother board problem or the problem can be provided by an another component (like processor, ram, ...)
Thank you
Damien

try clear CMOS. Try your CPU on other motherboard. Try other CPU on your motherboard.

Similar Messages

  • ALL LEDS ARE 'ON', Stuck condition

    My hp F2280 is inoperative. All LEDs are ON, power button is also not working.  If we power it OFF from the source and switch it ON after 5 minutes so it initialize but later when we turn it OFF through its power switch and then ON so this printer lits are
    the lights.
    Please assist.
    Awaiting of advise/resolution.
    Thanks in advance.

    Hi brandhilton,
    All the LED's should not be turning on. I've got a couple of troublehsooting steps for you:
    1) With the power off, disconnect all GPIB and Serial cables from your 232CV-A, and double check the DIP switch settings. Be sure to toggle each one.
    2) If you are using the DC version, double check that the power supply is supplying 9V at the DC connector.
    If all the LEDs are still turning on, please call 1-800-IEEE488 so that we can set up an RMA and get this taken care of.
    Thank you,
    Michael Chaney
    Systems Engineer - TestStand
    National Instruments

  • 648 max + 9700 boot issues - help

      hi
       i have a radeon 9700 (rev 1.3) and the 648 max - L and everything is working fine when i am in windows but sometimes when i cold boot i get no screen and it doesnt sound like i am booting up. i do see some hard drive activity but thats about it.  i try reset and sometimes it will work and others not, also when i install a program that needs to reboot sometimes it wont - basicaly the same problem as cold boot.
      i have a enermax 430  and so i doubt it is a psu problem, also like i said when i am in xp i have been able to play 3d games and run 3dmark and have yet to have any crashes.
      anyone have any solutions or suggestions as to what the problem is and how to fix it?
     

    Ok MSI called me back finally, I explained situation and told him that i have read other people with 0209 boards have had the same issues.
    He is cross shipping me a new 648max-L board I asked about it being backordered because of reading this thread and he said it should be shipped today or tomorrow so maybe they got boards in? Or maybe they modified a board that they are going to send me?
    He originally wanted me to send mine back and they would send me out a new one but i told him that i have no place to store the processor for that long of a time and i would be without a computer so he took my credit card number and put a hold of 100 dollars on it, once they receive my old one i will be credited.
    So all in all, i will be getting a new mobo and rev 1.3 radeon 9700 pro and i should be ready to go.
    Here is an email i received from MSI for those of you that are worried about resolving these issues.
    Dear Paul,
      I've just confirmed this with my collegue and he said that the first shipments need to be reworked.  Please send the board over to me directly and I'll take care of it for you.  Please include your address and make sure you get a tracking number for the package.
    Attention: Peter Hong
    MSI Computer
    901 Canada Court
    City of Industry, CA 91748
    Sincerely,
    Peter Hong
    http://www.msicomputer.com
    MSI is your TOP choice for DDR Solutions!
    E-mail: [email protected]
    1.626.913.0828
    1.626.581.7721 Fax

  • 648 max, wont boot to cd with locked HDD connected

    hi i hope you can help me, i bought my son a cheap second hand PC from a car boot sale, inside which is an MSI 648 max motherboard,
    the problem i have is i am trying to attach a larger hard drive which is locked, usually to unlock the HDD i run a bootable cd-rom which is fine however when i try to boot the computer i get a message stating the hard drive is locked and i have 5 attempts to enter the password.
    unfortunately i do not know the password as it is encrypted on the cd-rom, if only i could boot to cd-rom this wouldn't be a problem however i can not boot to cd-rom with the locked hard drive connected and obviously i cannot connect the hard drive after its booted to cd as it will not be detected,
    when i try to access the boot menu i hit F11 as stated but all i get on the POST screen is "GO-->boot menu and then it hangs on the POST screen, what does this mean?
    so my question is, is it possible to boot to CD with the locked HDD connected as im getting quite frustrated,
    i hope i have given enough information but if you need anymore i shall happily provide
    many thanks
    Glenn

    If the hard drive is still servicable you can use a bootable cd or floppy to erase the contents of the hard drive.
    The ultimate boot cd has numerous apps to erase hdds. http://www.ultimatebootcd.com/
    Or just get another hard drive.
    Could be something else wrong of course. At least the UBCD is free.

  • Help with Loops!! All loops are RED and unclickable after Leopard upgrade.

    I may need to just remove soundtrack pro from my computer and start from scratch again. When I upgraded to Leopard I failed to select preserve user settings when I did an archive and install. So therefore I had to find and drag files to the new library. This is on my Power Mac G5.
    I have a Macbook Pro laptop and I used that as a guide of how I have that set up. On my G5, I have all my loops in the same folders they are in on my laptop. When I open STP, and pull up my loop files, they are all listed in red. When I try to click on them, nothing happens.
    I have them set up as MAC>Library>Audio>Apple Loops>Apple Loops for Soundtrack Pro, Apple Loops for GarageBand, PowerFX Loops
    I am not sure if I am dealing with a bunch of corrupt files and need to start with a new slate or what.
    I also noticed that most if not all the audio loops end in .CAF instead of .AIFF in the folders. However when STP is open, the files ARE listed as .aiff files but they are red and non clickable.
    Any suggestions appreciated!
    Thanks!
    Message was edited by: DVX100Shooter
    Message was edited by: DVX100Shooter
    Message was edited by: DVX100Shooter

    Yea once I rearranged the loops and then opened STP and then Indexed those loops, I got everything back to normal except my Trumpet files. I cannot locate them anywhere. There are only 4 loops but I searched my HD and still can't locate where they are but I got everything else back to working.

  • All LEDs are lit on my GPIB-232CV-A. What's that mean?

    I just got my GPIB-232CV-A in today, and when I power it up, all the LEDs come on immediately and stay on. Looking at the manual, it looks like the Power LED is supposed to come on first, and then the Ready LED a few seconds after that, so I'm guessing that all LEDS on is some sort of error code, but I don't find any documentation for that anywhere.
    Any ideas?

    Hi brandhilton,
    All the LED's should not be turning on. I've got a couple of troublehsooting steps for you:
    1) With the power off, disconnect all GPIB and Serial cables from your 232CV-A, and double check the DIP switch settings. Be sure to toggle each one.
    2) If you are using the DC version, double check that the power supply is supplying 9V at the DC connector.
    If all the LEDs are still turning on, please call 1-800-IEEE488 so that we can set up an RMA and get this taken care of.
    Thank you,
    Michael Chaney
    Systems Engineer - TestStand
    National Instruments

  • 648 Max warm boot issue

    I have just built my first PC using a 648 Max MB. and I have a problem.
    The system boots up fine from cold start, however it fails to start in the following scenarios, it just beeps once and then sits there with a blank screen.
    # Restart form Windows
    # Shutdown from Windows (system powers off OK)
    # Exit from BIOS with or without saving changes
    The reset button has no effect
    The only way to get the system to boot is to remove power from supply and then restart.
    I note other threads of a similar nature!!!! O Dear
    System loaded with:
    Windows XP Professional
    2 x Kingston 256 DDR400 PC3200
    Intel P4 1.6GHz
    CONNECT 3D ATI RADEON 9200 128MB DDR + DVI + TV
    40GB Maxtor IDE

    Check the Power Management setp in your mobo's BIOS.

  • 648 Max-It boot up very slow!

    When i reboot or do a cold start when it passes the BIOS screen there is a delay for excact 10 sec between BIOS and WinXP logo loading screen.Any ideas what it could be?Anyone else got the same?

    Quote
    Originally posted by Rob454
    Some device drivers can hault boot time.. try booting to safemode and watch where the list of drivers pause and that may be your culprit.
    -rob
    What should i choose for start option to see that?When i take "Safe Mode" i goes to quick to see anything!

  • KT4 Ultra - 4 leds in RED (Urgent)

    I have a mb KT4 Ultra (MS-6590 v1.x) and cpu 2200+ .
    When a turn on the pc all fans are working but the system dont boot, all 4 leds are red.
    i just have enable the USB legacy support in BIOS and them save and exit , the pc hangs up , i reset pc and then the the 4 leds are red and dont boot anymore.
    I make all i know for fixing but i´m out of ideas   i dont know whats happend.
    I clear the bios in jumper jbat1 and take out the 3v battery and dosent work.
    What happend to the CPU??   Can anyone explain this...
    My system:
    KT4 Ultra (MS-6590 v1.0)
    AMD ATHLON XP 2200+
    2x256MB DDR333
    G4Ti4200-TD 128mb
    WINXP Prof. SP1a
    PSU:
     Model LC-A300ATX
     AC-I/P|  115/230v~ |    8/4A       | 60/50 Hz
     DC-     | +3.3V  +5V | +12v  -12v | -5v   +5VSB
     O/P     |    20A   30A |   10A   0.8A | 0.5A   2A
    +5v & +3.3v COMBINED LOAD 160W
    TOTAL OUTPUT IS 300W

    It would help if you tell us all you have done to fix problem. But I can say that 10 A. to 12v. line, seems very poor. I would disconnect all USB peripherals to see if PC boots. Also if before enabling USB legacy you connected USB brakets on Mobo's pinheaders, I would disconnect them too.

  • Relink does not work; all events staying red and files disappear!

    A very bad bad story...
    after continuis spinning ball (i hate this thing what so often comes to please me) I used "forced stop" fcpx. (i could not else)
    after restart fcpx all the events are in red.
    after restart mbp + fcpx: all events are red again... that looks bad to me...
    i tried more than ones the relinck function:
    no result at all. I saw actions being done, the harddisk drive was working but no relinked files in the events. (i tried one by one, there are 9)
    An other attempt with relinck: a small event (about 9 files) and not important for me seems to be going well, the red clips disappear in the event window but .. all clips disappeard to!; a totally empty event window... I looked with finder into the map and believe it or not: all the files were gone! I could not believe this thinking i made a fault.  Thus:
    I repeated this action with another map (and copied the files in it first) and the same happens: totally empty.
    I tried to re-import from camera/archief: no result.
    The last thing to do was:
    to open a new event and "imported from file": the clips came into the event window but .... red...
    So, in my opnion there is something very very wrong...
    What can i do more to restore the connection because the most events have a content according to the finder.
    BTW, i know there is a lot of discussion about this matter and may be with the solution but i can 't find it... (even with the searchfunction)
    For any help or suggestion: Thanks!
    Bruce.
    (I am going to sleep now, it is over midnight here)

    That's not stupid, I happened to me too yesterday.
    How are you supposed to know that the files fcpx is pointing out are originals or Proxies. You have to go check in the Prefs.
    Wishlist: Since choosing to read fullres or proxy media is an application wide feature, it should appear clearly somewhere (in the Timeline bar, the Library, or the Inspector) as a reminder.
    A couple of time I have wondered which files fcpx was reading. The only way to know is the cmd-F (Locate in Finder) command. The Inspector doesn't give any answer to that.

  • MSI 648 MAX Red diagnostic leds Help

    Hi
    Please help me !!!
    I have the 648 MAX mainboard with MSI G4MX440-VTD8X. The CPU is P4 2.4 Ghz  PC 533 and TwinMos DDR-DIMM PC3200 512MB DDR CL2.5 in Bank 2 . OS XP prof. Final ed.
    The two upper diagnostic led are weak red ??? I have checked the hard disc settings several times, but nothing is wrong there ??
    I have never seen a green diagnostic led, the other is are not lighting at all (black), only red ones ???
    I have looked from power on to working pc and thy are just blubering a litle to finaly two upper red ones ???
    This is the hottest hardware you can get so I set the Bios to opimal fast settings, but then all was black?? I hac to use the bios reset dip switch to get it back to working condition. What is wrong ?? It says on your web site that the mainboard do support DDR 400 ??
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=355&MODEL=MS-6585
    I can use the computher but I am not pleased with the two red diagnostic led ???
    I cant get any help here in norway because no one seems to bodder??
    These hard ware has a cost of 1100 $ for me, so I need to get it right please ??
    Regards
    Eivin Hjornevik
    Bergen
    Norway

    Have some suggestions on what to do, but I'm not sure it will help. If enyone else has something feel free..
    It's seams like you have had the PC up and running, and that's good.
    Regarding the diagnostic led's I can only suggest that you double check the connection to the board. (They all should either be green or red when booting).
    Even though it's hot hardware, loading the optimal fast setting is not the same as getting the best settings for your system.
    Regarding DDR400 and 648Max they didn't officially support it when they released the board, but they now do. I would suggest you check your version of the board. (I have ver 1.0 produced sept. 02, and my DDR400 has to be run as DDR333 to function properly).
    You don't say anything about your psu, but it should be above 200W combined.
    Help in Norway...? I'm here trying to help  

  • 648 Max booting problem

    Hi all,
    I just installed my new 648 Max / p4 / DDR PC3200 256MB hardware.
    Sadly it will not work.
    It hangs showing 4 Green LEDs.
    According to the manual it means; System booting,
    but nothing happens.  Nothing is written on the screen.
    I can see the CPU/GPU fans working fins.
    Any ideas ?(
    Thanks,
    zzzova.

    what is your DDR400?
    I had this problem too
    My first DDR400 was samsung and never boot at 400Mhz
    Now i have a 512Mo DDR400 Corsair and it work very fine

  • K9N2 SLI Platinum/ All 4 lights on motherboard are Red

    Specs are.
    9850 AMD Black Series
    600 W PSU OCZ
    1066 Ram OCZ Platinum Series 4 gigs
    BFG 9800GTX OC 512
    OS- Windows XP s3
    Problem I have is the manual i got is Multilingual and not very helpful, but what happened is a breaker in my house tripped and cut off power, and this happened while I was gaming on-line. Reset the breaker, turned the computer back on everything boots up fine but all the led lights are red, 4 total. Everything seems to be working just fine, didn't know if it was anything to be worried about or not. Thanks for any replys

    Didn't know that I would have to update the BIOS if I wanted the 1TB HDD support.  Thanks for pointing that out.
    Quote from: Scooter71 on 31-January-09, 05:38:58
    I didn't know if I should update the bios or not. IM on bios 3.2 and 3.3 is for updated CPU module, Support for 1000GB HDD and Support for L2 Function. So should I or not i guess is what im asking with me having the 9850 AMD Phenom is all. Thanks for any replys...

  • D-braket LED 1 and 4 are red

    i have the K8n plat. and i turned on the computer after i installed my liquid cooling and nothing at all, my pump and fans turn on and all i get are the d-bracket LED 1 and 4 are red. CPU bad? CPU initialization is where it hanges.
    my stats are
    MSI K8N neor2 plat.
    AMD64 3800+
    geforce 6800GT
    1.0gig OCZ value ram(new ram not in yet)
    2 HDD
    CDrom
    DVD-burner
    antec true power 480watt
    let me know what you all think.

    Quote
    Originally posted by brono85
    Hello all
    Today I received my mobo from RMA I put together ouside the case motherboard, processor, video card and the first boot I got the logo screen and nothing. The led on the D-braket are 1/3 are RED and 2/4 are Green. I tried to clear the bios with the jumper but nothing change, also I tried the bios recovery it gave me 5 bit and nothing.
    What should I do next?
    They did not replace my mobo I got the same one and I don't know what they do to my motherboard. On the sheet it said "Error code: U0H" "Repair: N01" any ideal what kind of repair they do?
    Need your help  Thank you
    Hi,
    Do MEMTEST 1st.........
    EDIT: 1/3 RED is mem error......
    Also 1.7 is best BIOS update, I have used stable with this mainboard.
    Will watch thread for replies.
    Del

  • Playbook won't turn on, boot, or charge. LED flashing red.

     Playbook won't turn on, boot, or charge. LED flashing red.

    Try this, while connected to your charger. Press and hold the Power key, up and down volume (-/+) all three buttons simultaneously, for about 10-12 seconds. You should the red LED blink and that should allow a reset of the PlayBook and to power up.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

Maybe you are looking for