6500 IOS HSRP Gateway not responding to ARP requests

WS-C6509, running Native IOS version 12.2(33)SXH4. Pair of 6500 configured with HSRP serving as Gateway to down stream clients
Ping requests from clients not having a Default Gateway (AIX Server Team recommendation) failing.
Packet capture show ARP requests being received by Gateway 6500, but Gateway will not respond for up to 30 seconds at which point ping requests will start working. But after a period of inactivity, the cycle starts over again - 30 second delay before traffic starts flowing.
Having a Default Gateway is a separate discussion. I'm just interested in being able to provide technical reason why this is occuring.
Anyone experience this?
Any suggestions for addtional troubleshooting measures?
Thanks in advance.

Looks to me like a timer problem - maybe a ARP timer on the clients? Check the ARP tables of your clients during your tests.
HTH

Similar Messages

Application Web Service Control Manager detected AWEBSVC is not responding to HTTP requests

Hi,
We are using SCCM 2012 sp1 cu5 with one primary in the datacenter and a number of local DP's which are presently servicing 200 users, but will rise to 12,000. The Application Catalogue is installed on the primary server.
Once a day we get the above error and the message id is 8101, and sometimes a user will have to click on install twice, with the first one failing (the ones that fail are normally with dependencies which are quite large in size around 250MB)
I'm just wondering if this is something I should be concerned about, especially since we will be ramping up user numbers in the next few weeks, and if it could be down to volume of traffic, although the apps are downloaded to the users local DP.
Also, does this design look suitable to service this amount of users, or should I have local application catalogues? The WAN bandwith between the datacenter and the user sites has recently been upgraded and is pretty fast.
Thanks
Jaz

Hi Torsten,
Message ID is in the SMS_AWEBSVC_CONTROL_MANAGER status log and equates to "Application Web Service Manager detected AWEBSVC is not responding to HTTP requests. The http error is 12002.
Then, about 1 hr later in the same monitoring log I get Message ID 8102 "Application Web Service Control Manger detected AWEBSVC is responding to HTTP requests.
At the moment it isn't doing this very often, just once a day at different times normally, but it has also logged this a couple of times as well. I guess it may correspond to multiple users accessing the web portal at multiple times, but wondered if
anyone else has seen this behaviour and how it was fixed.
Thanks
Jaz

Application Web Service Control Manager detected AWEBSVC is not responding to HTTP requests. The http status code and text is 400, Bad Request.

Hi All,
I am seeing the following error for SMS_AWEBSVC_CONTROL_MANAGER component with Message ID: 8100
Application Web Service Control Manager detected AWEBSVC is not responding to HTTP requests. The http status code and text is 400, Bad Request.
awebsctl.log file has below errors:
Call to HttpSendRequestSync failed for port 80 with status code 400, text: Bad Request
SMS_AWEBSVC_CONTROL_MANAGER 12/22/2014 3:37:55 PM
13920 (0x3660)
AWEBSVCs http check returned hr=0, bFailed=1
SMS_AWEBSVC_CONTROL_MANAGER 12/22/2014 3:37:55 PM
13920 (0x3660)
AWEBSVC's previous status was 1 (0 = Online, 1 = Failed, 4 = Undefined)
SMS_AWEBSVC_CONTROL_MANAGER 12/22/2014 3:37:55 PM
13920 (0x3660)
Health check request failed, status code is 400, 'Bad Request'.
SMS_AWEBSVC_CONTROL_MANAGER 12/22/2014 3:37:55 PM
13920 (0x3660)
Management point and Application Catalog Website Point are installed on the same Server where I am seeing the error for Application Catalog Web Service Point role. Management Point and Application Catalog Website Point are functioning properly. Application
Catalog Website is working.
Thanks & Regards, Kedar

Hi Jason,
Application Catalog Web Service Point and Application Catalog Website Point; both are installed as per below configuration on same Server:
IIS Website: Default Web Site
Port Number: 80
with default value for Web Application Name configured.
For SMS_AWEBSVC_CONTROL_MANAGER component, I am getting below error in Component Status:
Application Web Service Control Manager detected AWEBSVC is not responding to HTTP requests. The http status code and text is 400, Bad Request.
Possible cause: Internet Information Services (IIS) isn't configured to listen on the ports over which AWEBSVC is configured to communicate.
Solution: Verify that the designated Web Site is configured to use the same ports which AWEBSVC is configured to use.
Possible cause: The designated Web Site is disabled in IIS.
Solution: Verify that the designated Web Site is enabled, and functioning properly.
For more information, refer to Microsoft Knowledge Base.
And awebsctl.log has the below error lines:
Call to HttpSendRequestSync failed for port 80 with status code 400, text: Bad Request
SMS_AWEBSVC_CONTROL_MANAGER
12/23/2014 11:04:36 AM 16388 (0x4004)
AWEBSVCs http check returned hr=0, bFailed=1
SMS_AWEBSVC_CONTROL_MANAGER
12/23/2014 11:04:36 AM 16388 (0x4004)
AWEBSVC's previous status was 1 (0 = Online, 1 = Failed, 4 = Undefined)
SMS_AWEBSVC_CONTROL_MANAGER
12/23/2014 11:04:36 AM 16388 (0x4004)
Health check request failed, status code is 400, 'Bad Request'.
SMS_AWEBSVC_CONTROL_MANAGER
12/23/2014 11:04:36 AM 16388 (0x4004)
STATMSG: ID=8100
What should I check from IIS side?
Application Catalog Website is functioning properly.
Thanks & regards,
Kedar
Thanks & Regards, Kedar

HP Photosmart 5514 e-All-in-One Printer - B111h not responding to print requests on Windows 8

Hello there,
Recently, I've been having these problems where the Printer is not responding for my requests to print on my HP Windows 8 Laptop for a PDF File. I had a message where it said that "Printer is in error state" but didn't get that message after I tried printing again. Now my printer is not responding to any print requests though the touch screen still works and is saying that the wireless is still working. If anyone could help me that would be great!
Thank you for your time.

I see that you are having a problem printing from Windows 8.
See if you can print a self-test page or Printer status report from the printer itself. This will test the hardware functionality for the printer. If it does print, then it's a connection issue. If it does not print out, then we will need to try to deal with the hardware problems of the printer.
Run the print and scan doctor and check the results.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c03275041
**Click the KUDOS star on the left to say 'Thanks'**
Please mark a reply "ACCEPTED AS SOLUTION" if it solved your problem, so others can find it.

I hired a commercial artist to create a color image for the cover of a self published book. I want a black and white image for the inside. The commercial artist has not responded to this request. How do I determine the format of the color image, I'm guess

I hired a commercial artist to create a color image for the cover of a self published book. I want a black and white image for the inside. The commercial artist has not responded to this request. How do I determine the format of the color image, I'm guessing it's Illustrator's formatting but I don't know. How can I find out if Illustrator will open the file and allow alterations? The image opens only in Apple's Pages software?

rons,
It seems that all you have is a raster image, presumable PNG24 or JPEG, in RGB.
It may have been created as raster artwork in Photoshop, or it may have been created as vector artwork with the help of Illy, or as a mixture of vector and raster artwork in either application, or both combined.
If you just need to have a raster representation in black and white based on the current colour image, you may try this, in a new RGB document (View>Smart Guides are your friends):
1) File>Place the image (you may tick Link or untick and have it embedded);
2) Create a rectangle with black fill (R = G = B = 0), at least as large as the image, and place it behind the image (you may ClickDrag with the Rectangle Tool between opposite corners, then Ctrl/Cmd+X+B);
3) Select all and in the Transparnecy palette flyout click Make Opacity Mask with both Clip and Invert Mask ticked.

Remote gateway not responding using linksys vpn client

Please i need your assistance asap
Am using this
Linksys VPN router RV042, firmware version 1.3.12.19-tm
Linksys VPN Client version 1.2.11
When i trying connecting via the VPN client on a window XP SP3 system it
goes through the process of connecting,provisioning, activating policy
and hang on verifying network. After a while a pop box comes up with ''
The remote gateway is not responding. Do you want to wait''
The RV042 shows that the client is log on and online.but the VPN client
access say The remote gateway is not responding. Do you want to wait''
see below my vpn client log
2012/07/26 16:17:55 [STATUS]OS Version: Windows XP2012/07/26 16:17:55 [STATUS]Windows Firewall is OFF2012/07/26 16:17:55 [STATUS]One network interface detected with IP address 10.54.39.592012/07/26 16:17:55 [STATUS]Connecting...2012/07/26 16:17:55 [STATUS]Connecting to remote gateway with IP address: 41.78.96.452012/07/26 16:18:10 [STATUS]Remote gateway was reached by https ...2012/07/26 16:18:10 [STATUS]Provisioning...2012/07/26 16:18:23 [STATUS]Tunnel is connected successfully.2012/07/26 16:18:23 [STATUS]Verifying Network...2012/07/26 16:18:27 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:18:30 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:18:31 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:18:33 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:18:36 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:18:59 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.2012/07/26 16:19:10 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:19:13 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:19:18 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:19:21 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:19:27 [WARNING]Failed to ping the remote VPN Router!2012/07/26 16:19:55 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.2012/07/26 16:20:03 [STATUS]Disconnecting...2012/07/26 16:20:17 [STATUS]Tunnel is disconnected successfully.
PLEASE I NEED HELP!!!!!! OR ANY OTHER OPTION TO ACCESS MY CENTRAL VPN GATEWAY
Celestine
Specstech Africa

Discussions about the WRVS4400N is now being handled by the Cisco Small Business Support Community.
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router

PLEASE HELP ME!!! ipod touch 3rd gen 32 gb ios 5 sreen not responding to touch! What can i do ?

My ipod touch battery ran out and i went to charge it using a wall adapter. it turn on got stuck in a boot loop for 15 min before going to the lock screen. after that, the screen is not responding to my touch what can i do?

- First try resetting hte iPod. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Next connect to your computer and restore from backup
- Then try restoring to factory defaults/new iPod.

HT4623 IOS 6 is not responding

IOS6 not responding,having a problem downing music and battery not chariging properly

You say it's not responding but then mention it is but not correctly
I recommend you first:
Reboot the device, then if you are still having issues do a full reset. - settings - general - reset, at the bottom of the page
If you do not have a back up, try to back up first as it wipes and restores the device to the default settings

WLS 10.3 Does not respond to GET requests (HTTP/1.0)

Hi All,
I have 2 WLS servers running on separate physical hosts behind a cisco CSS load balancer. The keep-alive method the Cisco CSS uses is HTTP GET messages. This keep-alive method does not appear to work, because my WLS servers are not responding to the GET requests with HTTP 200 OKs (as would be expected). These GET messaged appear in the access logs, as follows, but from traces taken on the host, there are no HTTP 200 messages ever transmitted. I see no exceptions or errors related to this in the server or access logs.
WLS access log:
192.168.1.1 - - [14/Dec/2011:18:23:35 +0000] "HEAD /APPDIR/index.jsp HTTP/1.0" 200 0
192.168.1.1 - - [14/Dec/2011:18:23:45 +0000] "HEAD /APPDIR/index.jsp HTTP/1.0" 200 0
192.168.1.1 - - [14/Dec/2011:18:23:55 +0000] "HEAD /APPDIR/index.jsp HTTP/1.0" 200 0
Interestingly, If i use a http-ping tool to send HEAD messages, the server correctly responds with the 200. A major difference between the CSS and the ping-tool, is that the CSS is using HTTP/1.0 where the ping tool uses HTTP/1.1. The GET requests are formatted a bit differently too. Below is how the different GET messages are formatted. Is it possible that WLS 11g does not support HTTP/1.0? Is there any method of debugging that I can employ to troubleshoot this further? As mentioned I do not see any errors or exceptions in the server logs or access logs....
Many thanks, in advance.
HTTP-PING TOOL HEAD MESSAGE - weblogic responds to this message
HEAD /APPDIR/index.jsp HTTP/1.1
Host: myhost.domain.com:7005
Accept: */*
LOAD BALANCER HEAD MESSAGE -weblogic does not respond to this message
HEAD /APPDIR/index.jsp HTTP/1.0
Connection: Keep-Alive
User-Agent: Mozilla/4.06 [en] (WinNT; I)
Accept: image/gif, image/x-bitmap, image/jpeg, image/pjpeg, image/png, */*
Accept-Language: en
Accept-Charset: iso-8859-1,*,utf-8
Host: 192.168.1.66

Other than failing the base address test, does the device seem to work in the test panels? One quick test would be to open the digital I/O panel, change some of the lines to output, toggle the logic levels, and see if the line states track the logic levels. Also, you can switch to the Counter I/O panel, change the mode to simple event counting, set the event source to the internal 100KHz clock, and start the counter. If the counter is working properly, you should see the counter value increase at a rate of 100000/second.
If the test panels seem to work OK, you may still be able to use the board, despite the resource test failing. I still can't explain why the test fails, though.
Joe

WebLogic is not responding to client request under heavy load

Under heavy loading, our WLS 6.0 SP2 will be not be responding to client requests
after some time, say, 1 hour. From the administration console, the request throughput
is 0 while request waiting accumulates to over 1,000. Even the clients stop making
request to the server, the request waiting will not drop. It seems that WLS blocked
on some threads and unable to serve the requests (see attached thread dump for
details).
Our configuration is as follow:
OS: SunOS 5.7
Database: MS SQL Server 7.0 running on NT4 Enterprise Edition.
(JDBC Driver is the one bundled with WLS 6.0)
We know that using 'DriverManager.getConnection()' can cause deadlock in number
of cases but we have gone through all the code but all of our Database connections
are obtained through datasource. And the connection is closed properly in finally
block.
Moreover, the application is originally running on WLS 4.51 but no problem is
encountered.
Does any expert know what the problem and solution are?
Thanks!
[session.log]

It appears that some threads were possibly blocked at some jDriver calls
initially (ExecuteThread 0,10,15,23 of the default thread pool). WLS JTA
subsequently timed out and rolled back the transactions asynchronously. The
first rollback attempt was blocked at the jDriver level (ExecuteThread 18 of
the default thread pool). Each subsequent rollback retry blocks an
additional execute thread (due to a JTA bug that is fixed in WLS 6.1, but
not 6.0 SPs) - ExecuteThread 1-9,11-26 of the default thread pool.
Eventually, the server ran out of execute threads and became unresponsive.
It is unclear that whether the initial blocking of threads by the jDriver is
a jDriver issue or an application issue. Please report to BEA support at
[email protected] for further assistance.
Regards,
Priscilla
Gary Mok <[email protected]> wrote in message
news:[email protected]..
>
Under heavy loading, our WLS 6.0 SP2 will be not be responding to clientrequests
after some time, say, 1 hour. From the administration console, the requestthroughput
is 0 while request waiting accumulates to over 1,000. Even the clientsstop making
request to the server, the request waiting will not drop. It seems thatWLS blocked
on some threads and unable to serve the requests (see attached thread dumpfor
details).
Our configuration is as follow:
OS: SunOS 5.7
Database: MS SQL Server 7.0 running on NT4 Enterprise Edition.
(JDBC Driver is the one bundled with WLS 6.0)
We know that using 'DriverManager.getConnection()' can cause deadlock innumber
of cases but we have gone through all the code but all of our Databaseconnections
are obtained through datasource. And the connection is closed properly infinally
block.
Moreover, the application is originally running on WLS 4.51 but no problemis
encountered.
Does any expert know what the problem and solution are?
Thanks!

WLC is not responding to SNMP requests.

Customer is using a 4400 WLC.
He has a management tool that works using the SNMP logs from the controller, he can ping the
controller using this management tool, but when he sends SNMP requests from the management tool the
WLC doesn't reply.
The SNMP server IP address is 192.168.122.11 and the WLC's IP address is 10.20.1.31.
I have the following debug taken from the switchport where the WLC is connected.
'debug snmp agent' shows some interesting messages that confirms that the WLC is not sending a packet back.
Cisco Controller) >debug snmp agent enable
(Cisco Controller) >*SNMPTask: Feb 06 14:38:44.616: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 59
*SNMPTask: Feb 06 14:38:44.616: SNMPD: Failed to build in SnmpMessage.
1145 Debug Messages have been dropped*SNMPTask: Feb 06 14:38:44.616: SNMPD: *NOT* sending out packet, out_packet_len = 0
*SNMPTask: Feb 06 14:38:47.621: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 59
*SNMPTask: Feb 06 14:38:47.621: SNMPD: Failed to build in SnmpMessage.
*SNMPTask: Feb 06 14:38:47.621: SNMPD: *NOT* sending out packet, out_packet_len = 0
*SNMPTask: Feb 06 14:38:50.652: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 59
*SNMPTask: Feb 06 14:38:50.652: SNMPD: Failed to build in SnmpMessage.
*SNMPTask: Feb 06 14:38:50.652: SNMPD: *NOT* sending out packet, out_packet_len = 0
*SNMPTask: Feb 06 14:38:53.684: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 50
*SNMPTask: Feb 06 14:38:53.684: SNMPD: Failed to build in SnmpMessage.
*SNMPTask: Feb 06 14:38:53.684: SNMPD: *NOT* sending out packet, out_packet_len = 0
*SNMPTask: Feb 06 14:38:56.715: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 50
*SNMPTask: Feb 06 14:38:56.715: SNMPD: Failed to build in SnmpMessage.
*SNMPTask: Feb 06 14:38:56.715: SNMPD: *NOT* sending out packet, out_packet_len = 0
*SNMPTask: Feb 06 14:38:59.747: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 50
*SNMPTask: Feb 06 14:38:59.747: SNMPD: Failed to build in SnmpMessage.
*SNMPTask: Feb 06 14:38:59.747: SNMPD: *NOT* sending out packet, out_packet_len = 0
I have also a packet capture taken from the same switchport, I attach it here.
What could be the reason for not responding?

You need to add the management tool in the WLC as a trap reciever.
Thanks,
Scott
*****Help out other by using the rating system and marking answered questions as "Answered"*****

IOS VPN will not respond to Cisco VPN Client connections.

Hi all,
I am about to set my routers on fire here.
I have two 2921 ISRs both with Security licenses on separate leased lines. I have configured one to accept VPN connections from our Cisco VPN Client remote workers.
I have followed the set up process I used on another site with an 1841/Sec router and the same clients and I have also checked against the config given in the latest IOS15 EasyVPN guide.
With all debugs active, all I see is
038062: Dec 8 14:03:04.519: ISAKMP (0): received packet from x.y.z.z dport 500 sport 60225 Global (N) NEW SA
038063: Dec 8 14:03:04.519: ISAKMP: Created a peer struct for x.y.z.z, peer port 60225
038064: Dec 8 14:03:04.519: ISAKMP: New peer created peer = 0x3972090C peer_handle = 0x8001D881
038065: Dec 8 14:03:04.523: ISAKMP: Locking peer struct 0x3972090C, refcount 1 for crypto_isakmp_process_block
038066: Dec 8 14:03:04.523: ISAKMP:(0):Setting client config settings 3E156D70
038067: Dec 8 14:03:10.027: ISAKMP (0): received packet from x.y.z.z dport 500 sport 60225 Global (R) MM_NO_STATE
Below is the abridged config.
System image file is "flash0:c2900-universalk9-mz.SPA.154-1.T1.bin"
aaa new-model
aaa authentication login default local
aaa authentication login VPNAUTH local
aaa authorization exec default local
aaa authorization network VPN local
aaa session-id common
crypto isakmp policy 10
encr aes
authentication pre-share
group 14
crypto isakmp client configuration group VPN
key ****-****-****-****
dns 192.168.177.207 192.168.177.3
domain xxx.local
pool VPNADDRESSES
acl REVERSEROUTE
crypto ipsec transform-set HASH esp-aes esp-sha-hmac
mode tunnel
crypto ipsec profile IPSECPROFILE
set transform-set HASH
crypto dynamic-map VPN 1
set transform-set HASH
reverse-route
crypto map VPN client authentication list VPNAUTH
crypto map VPN isakmp authorization list VPN
crypto map VPN client configuration address respond
crypto map VPN 65535 ipsec-isakmp dynamic VPN
ip local pool VPNADDRESSES 172.16.198.16 172.16.198.31
ip access-list extended REVERSEROUTE
permit ip 192.168.0.0 0.0.255.255 any
permit ip 10.0.0.0 0.0.0.255 any
ip access-list extended FIREWALL
2 permit udp any host a.b.c.d eq non500-isakmp
3 permit udp any host a.b.c.d eq isakmp
4 permit ahp any host a.b.c.d
5 permit esp any host a.b.c.d
If anyone can see anything wrong, I would be so pleased and it would save the destruction of an ostensibly innocent router.
Thanks,
Paul

> I actually love you. Thank you so much.
Sorry, I'm married ... ;-)
> Im not using a virtual template. Can I get away without the Crypto Map if I use one...? All my tunnels are VTIs
oh yes, I could have seen that ...
crypto isakmp profile VPN-RA
match identity group VPN
client authentication list VPNAUTH
isakmp authorization list VPN
client configuration address respond
virtual-template 1
interface Virtual-Template1 type tunnel
description Tunnel fuer Cisco VPN-Client
ip unnumbered GigabitEthernet0/0
ip virtual-reassembly in
tunnel mode ipsec ipv4
tunnel protection ipsec profile IPSECPROFILE
Your isakmp-config and ipsec profile stays the same.

Hsrp problem....hsrp address not responding

Hi
I'm hoping I can get some opinions on this. I have 2 7200 routers with 2 gig interfaces each. Each gig interface is connected to 2 stacked 3750 switches. I have sub interfaces configured on both the gig interfaces so they are essentially dot1q to the 3750 switches. I have specified a hsrp group for each subinterface on the 7200s. My problem is that when I have 1 of the 7200 routers acting as hsrp active for some groups and the other 7200 acting as hsrp active for other groups hosts lose connectivity to their hsrp address for one of the routers. i.e no response to pings yet correct mac address in arp table.All works well when I make either one of the routers the hsrp active for all of the groups. Any ideas?
r1----3750----hosts
\/ | <--stack
/\ |
r2----3750----hosts

config for one router is below.The other router is the same apart from the track command and the priority is 155. The 2 3750s have the vlans configured and dot1q trunks to both of the routers 2 gig ports.
the show standby at the moment shows the correct info ie the correct router is active for all the groups...
thanks
interface GigabitEthernet0/1
description *** Primary link to Switch 1 ***
no ip address
no ip proxy-arp
duplex auto
speed auto
media-type sfp
negotiation auto
interface GigabitEthernet0/1.10
encapsulation dot1Q 10
ip address x.x.x.x 255.255.255.224
no ip proxy-arp
no snmp trap link-status
standby 10 ip x.x.x.x
standby 10 priority 160
standby 10 preempt delay minimum 60
standby 10 track GigabitEthernet1/0
interface GigabitEthernet0/1.30
encapsulation dot1Q 30
ip address x.x.x.x 255.255.255.192
no ip proxy-arp
no snmp trap link-status
standby 30 ip x.x.x.x
standby 30 priority 160
standby 30 preempt delay minimum 60
standby 30 track GigabitEthernet1/0
interface GigabitEthernet0/1.70
encapsulation dot1Q 70
ip address x.x.x.x 255.255.255.252
no ip proxy-arp
no snmp trap link-status
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description **** secondary link to switch 2 ***
no ip address
no ip proxy-arp
duplex auto
speed auto
media-type sfp
negotiation auto
interface GigabitEthernet0/2.20
encapsulation dot1Q 20
ip address x.x.x.x 255.255.255.224
no ip proxy-arp
ip ospf network broadcast
no snmp trap link-status
standby 20 ip x.x.x.x
standby 20 priority 160
standby 20 preempt delay minimum 60
standby 20 track GigabitEthernet1/0
interface GigabitEthernet0/2.40
description *** N2 Web Farm ***
encapsulation dot1Q 40
ip address x.x.x.x 255.255.255.192
no ip proxy-arp
no snmp trap link-status
standby 40 ip x.x.x.x
standby 40 priority 160
standby 40 preempt delay minimum 60
standby 40 track GigabitEthernet1/0
interface GigabitEthernet0/2.50
encapsulation dot1Q 50
ip address x.x.x.x 255.255.255.240
no ip proxy-arp
no snmp trap link-status
standby 50 ip x.x.x.x
standby 50 priority 160
standby 50 preempt delay minimum 60
standby 50 track GigabitEthernet1/0
interface GigabitEthernet0/2.80
encapsulation dot1Q 80
ip address x.x.x.x 255.255.255.252
no ip proxy-arp
ip ospf network broadcast
no snmp trap link-status

My dear during i update my iphone 4s 16 giga to ios 7 itis not responde and error 4005 wasfound please help me

dear sir during updating my iphone 4s 16 giga error 4005 found please help me

http://lmgtfy.com/?q=iPhone+error+code+4005

Outlook 2010 People Pane not displaying all Accepted, Tentative, Declined, or Not Responding, for meeting requests.

I have a user that sends out a local employee meeting request, so it goes out to about 100 people. She then tracks the responses by opening the event in her calendar, and looking at the information in the people pane. But this only shows her
59 responses. I was having her copy the tracking to a clipboard, then pasting it into an excel sheet. Then she could sort it to see who isn't going, or hasn't responded. but that also only populates 59 people. We use exchange server,
and she's running exchange 2010.
I'd appreciate any help, or suggestions.
thanks,
Jeff

Hi Jeff,
How many people can you see if we open the meeting and view the tracking information from OWA?
Are the missing people external meeting attendees? By default, Microsoft Exchange Server 2010 is not configured to process external meeting requests or meeting responses. Your mailbox has to be configured to process external meeting requests and meeting
responses.
For more information, please refer:
http://support.microsoft.com/kb/2331322
Hope this helps.
Regards,
Steve Fan
TechNet Community Support

6500 IOS HSRP Gateway not responding to ARP requests

Similar Messages

Maybe you are looking for