6500 Slide Active Standby Question

My Active Standby is only displaying 1 event whereas my old 6280 displays more than 1. Is it possible for the 6500 Slide to display more than 1?
Thanks in advance.

BUMP

Similar Messages

Router HSRP Active/Standby question

Hello,
Can I use following command to setup HSRP Active/Standby mode for both router ?
Router A:
ip address 10.10.228.202 255.255.255.248
standby 3 ip 10.10.228.201
standby 3 preempt
Router B:
ip address 10.10.228.203 255.255.255.248
standby 3 ip 10.10.228.201
standby 3 preempt
standby 3 track 1 decrement 10
standby 3 track 2 decrement 10
Thanks

Wilson,
we don't know what objects you're tracking, so it's a little bit difficult to answer the question.
You use the default priorities on both routers (100), so, as long as track objects 1 and 2 are up, Router B will be the active router, because it has the higher IP address.
If track object 1 or 2 goes down, Router B's priority will be reduced to 90 (or 80 if both are down at the same time), so Router A will become active, because preemption is enabled.
If the track object(s) change to up, Router B will take over again, because it also has preemtion enabled.
Correction:
Preemption only comes into play when the local priority is higher than the priority of the current active router. In your examle, the priorities on RA and RB have the same values. The IP addresses serve as a tie breaker only in the initial phase, the preemption feature doesn't consider the IP addresses later on.
Consequence: Router A continues beeing the active router.
HTH
Rolf

Active Standby Question

I have a Nokia E60, which operates using Symbiuan 9.1, series 60 3rd edition. This software lets you put 6 shortcuts on the main screen (active standby). There is an interface to change which shortcuts are used. I want to make a shortcut to the "Installations Directory" so that I will have a fast way to access my installed programs but this directory does not appear on the list of possible shortcuts. Does anyone know if this is possible? If so, how? Thanks,
Mark

No can do. Only individual apps seem to work as Active Standby shortcuts, not menu folders.

FWSM move from Active/Standby to Active/active

Hi there,
we have some FWSM installed in 6500 with many contexts in them. They are at the moment configured as Active/Standby and in production. But we have noticed that whenever a backup is run which goes through some of the contexts, the FWSM start counting errors which was already determined to be an oversubscription issue. So, while we wait for the new ASA 5585X to arrive and finally replace them, we want to mitigate the issue by configuring the FWSM as Active/Active and move the contexts for backup traffic to the other box (keeping the production contexts in the other one).
My question is, can this be done without impacting the production traffic? Or as soon as we enable the active/active by the configuration of the groups and assignments of the contexts, the traffic will be impacted and we will produce an outage to the network?
Thanks in advance for your help.
Regards,
Paula

So no answers?
Just one to update why had problem here: we need to to pull changes from Physical StandBy, because of performance reasons we cannot afford to reload every table with full refresh, we only want to get changes. At first I thought that it will be easy just create materialized view log and do basic replication, but in Physical StandBy we cant do it

ASA 5520 VPN load balancing with Active/Standby failover on 2 devices only...

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
This topic has been beat to death, but I did not see a real answer. Here is configuration:
1) 2 x ASA 5520, running 8.2
2) Both ASA are in same outside and inside interface broadcast domains – common Ethernet on interfaces
3) Both ASA are running single context but are active/standby failovers of each other. There are no more ASA’s in the equation. Just these 2. NOTE: this is not a Active/Active failover configuration. This is simply a 1-context active/standby configuration.
4) I want to share VPN load among two devices and retain active/standby failover functionality. Can I use VPN load balancing feature?
This sounds trivial, but I cannot find a clear answer (without testing this); and many people are confusing the issue. Here are some examples of confusion. These do not apply to my scenario.
Active/Active failover is understood to mean only two ASA running multi-contexts. Context 1 is active on ASA1 Context 2 is active on ASA2. They are sharing failover information. Active/Active does not mean two independently configured ASA devices, which do not share failover communication, but do VPN load balancing. It is clear that this latter scenario will work and that both ASA are active, but they are not in the Active/Active configuration definition. Some people are calling VPN load balancing on two unique ASA’s “active/active”, but it is not
The other confusing thing I have seen is that VPN config guide for VPN load balancing mentions configuring separate IP address pools on the VPN devices, so that clients on ASA1 do not have IP address overlap with clients on ASA2. When you configure ip address pool on active ASA1, this gets replicated to standby ASA2. In other words, you cannot have two unique IP address pools on a ASA Active/Standby cluster. I guess I could draw addresses from external DHCP server, and then do some kind of routing. Perhaps this will work?
In any case, any experts out there that can answer question? TIA!

Wow, some good info posted here (both questions and some answers). I'm in a similar situation with a couple of vpn load-balanced pairs... my goal was to get active-standby failover up and running in each pair- then I ran into this thread and saw the first post about the unique IP addr pools (and obviously we can't have unique pools in an active-standby failover rig where the complete config is replicated). So it would seem that these two features are indeed mutually exclusive. Real nice initial post to call this out.
Now I'm wondering if the ASA could actually handle a single addr pool in an active-standby fo rig- *if* the code supported the exchange of addr pool status between the fo members (so they each would know what addrs have been farmed out from this single pool)? Can I get some feedback from folks on this? If this is viable, then I suppose we could submit a feature request to Cisco... not that this would necessarily be supported anytime soon, but it might be worth a try. And I'm also assuming we might need a vip on the inside int as well (not just on the outside), to properly flip the traffic on both sides if the failover occurs (note we're not currently doing this).
Finally, if a member fails in a std load-balanced vpn pair (w/o fo disabled), the remaining member must take over traffic hitting the vip addr (full time)... can someone tell me how this works? And when this pair is working normally (with both members up), do the two systems coordinate who owns the vip at any time to load-balance the traffic? Is this basically how their load-balancing scheme works?
Anyway, pretty cool thread... would really appreciate it if folks could give some feedback on some of the above.
Thanks much,
Mike

FWSM Active/Standby in VSS mode

hello,
i do have two 6500 in VSS mode , and one FWSM module on each 6500, i want to configure these modules as Active/Standby, how do i start , should i follow this (not in VSS mode):
http://www.cisco.com/en/US/docs/security/fwsm/fwsm32/configuration/guide/fail_f.html
or are there other things should i do to make it work,
thanks

up!

Nokia 6500 slide - SMS writing language (chinese) ...

Hi,
Seek helps from all experts, I have recently updated my Nokia 6500 Slide firmware to 8.4. but unfortunately it cause some changes to my phone as the SMS writing language for Chinese characters has disappeared. Anyone could advise me on how to install it back to my phone?
Thanks.
Regards,
Stevenzder

the following sticky post should answer your question about why your chinese language disappeared.
/discussions/board/message?board.id=swupdate&thread.id=29982
you can visit the nearest nokia care point to have that additonal language added to phone.
Fear not those who argue but those who dodge

Orange 6500 Slide Firmware change.

Hello,
I bought an unlocked Orange Nokia 6500 Slide without knowing about the Firmware. It is completely hideous. I'd like to have the standard Nokia Frimware.
Could anyone help me with this?
Help is very much appreciated.
Thank you for your time! :-)

If you get written consent from the operator in question, a Nokia service point may be able to flash the phone with the standard Nokia software. Note, however, that they aren't required to do this by Nokia and so may not do.
Any other method that may exist would invalidate the warranty - we are not allowed to discuss that sort of thing here.

IPS modules in Cisco ASA 5510 Active/Standby pair.

All, I am looking to add the IPS module to my ASA 5510's. I am contemplating only purchasing one module and placing it in the active ASA. I am willing to accept that in a failure scenario I will loose the IPS functionality until the primary ASA is recovered. I have not had a chance to talk to my SE to see if this is even possible. Has anyone attempted a deployment such as this? Will it work and is it supported?
Sent from Cisco Technical Support iPad App

Ok, that is what I needed to know. The purpose of us having an active/standby ASA is to keep the business up and going for the very rare times there could be an active ASA failure. The purpose for the IPS would be to help protect and inspect traffic and is not necessary to keep the business running. If we implement IPS I am not worried at all if during the times when the primary ASA is down (hasn't been down for over three years now) we lose the IPS funcationality. This is not worth the $1000 extra per year to us.
Thanks for the responses though. That answers my questions.

Step to prep CSC SSM on ASA Active/Standby mode

Hi all,
I am trying to setup Active/Standby HA mode for my site.
Currently the site was installed with one unit ASA firewall with CSC-SSM module, the second unit is the new unit ready to be setup.
My question:
01. My concern is second unit CSC-SSM, what is the proper procedure or step need to prep it?
Is it need to prep the CSC-SSM before the ASA in HA mode Or it will auto propagate the configuration when both unit in HA mode?
What else need to concern? am i need to setup different IP for the CSC-SSM management interface?
Thanks
Noel

Hello Yong,
Configuration related to the CSC or SSM modules will never get propagated so you will basically need to configure it manually.
Also it's not like if the Config on both modules is different failover will fail but ofcourse you wanna have the same one
IP addresses for each of the modules will be dedicated ones. Remember that failover will fail if one box has the CSC and the other not.
Looking for some Networking Assistance?
Contact me directly at [email protected]
I will fix your problem ASAP.
Cheers,
Julio Carvajal Segura
http://laguiadelnetworking.com

How to tell if Active/active or Active/Standby mode is configured?

Folks:
I am still learning the output of my running config, but how do I tell if my firewall is set to Actve/Active or Active/Standby mode?
In addition, how do I tell if it uses regular or stateful failover mode?
Thank you

I wanted to provide this as well, since I found it and it also helped me answering my question.
This output shows Active/Active failover output.
**Note** it says PIX; however, I beleive it will be the same output for ASA.
PIX1(config-subif)#show failover
Failover On
Cable status: N/A - LAN-based failover enabled
Failover unit Primary
Failover LAN Interface: LANFailover Ethernet3 (up)
Unit Poll frequency 15 seconds, holdtime 45 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 4 of 250 maximum
Version: Ours 7.2(2), Mate 7.2(2)
Group 1 last failover at: 06:12:45 UTC Apr 16 2007
Group 2 last failover at: 06:12:43 UTC Apr 16 2007
This host:    Primary
Group 1       State:          Active
                Active time:    359610 (sec)
Group 2       State:          Standby Ready
                Active time:    3165 (sec)
                  context1 Interface inside (192.168.1.1): Normal
                  context1 Interface outside (172.16.1.1): Normal
                  context2 Interface inside (192.168.2.2): Normal
                  context2 Interface outside (172.16.2.2): Normal
Other host:   Secondary
Group 1       State:          Standby Ready
                Active time:    0 (sec)
Group 2       State:          Active
                Active time:    3900 (sec)
                  context1 Interface inside (192.168.1.2): Normal
                  context1 Interface outside (172.16.1.2): Normal
                  context2 Interface inside (192.168.2.1): Normal
                  context2 Interface outside (172.16.2.1): Normal

Stop/start in PGW active/standby mode

Hi all
My VOIP Network has 2 PGW in active/standby mode. But when we add more telco, the state of ss7path is OOS. i must stop/start the PGW and ss7path is IS status.
Now PGW is running services. it processing many call with other telco.
i have question need to support.
When we stop/start PGW,has PGW disconnected all call or not?
Thank for supporting
PhaiLQ

If you restart the service on active pgw, calls are disconnected. If you don't want out of services you must pass the control to the standby server first.
From mml console of active server use the command:
rtrv-ne    to check the status, the output is:
    MGC-01 - Media Gateway Controller 2010-09-07 16:53:42.655 MEST
M RTRV
   "Type:MGC"
   "Hardware platform:sun4u sparc SUNW,Sun-Fire-V240"
   "Vendor:"Cisco Systems, Inc.""
   "Location:MGC-01 - Media Gateway Controller"
   "Version:"9.6(1)""
   "Platform State:ACTIVE"
sw-over::confirm to swich control to standby server
now restart the service
/etc/init.d/CiscoMGC stop
/etc/init.d/CiscoMGC start
P.S. If I remember the right way, the OOS (out of service) state of new ss7 path can be set in IS (in service) via mml command line without service restart.
set- your ss7 path ::IS   use tab for help
Regards.

Calendar entries in Active Standby mode

A double question, but both are closely related.
In Active Standby mode it shows upcoming calendar entries for today and future ones.
Q1) Can someone clarfify does it only show 1 entry for future events, since I have placed 2 entries for tomorrow and 1 for the day after. But only 1 (the first) appears in Active Standby.
Q2) I THINK IS A BUG!! It does not show Anniversary as future events in Active Standby. It only appears when it is on the day (bit late if you need to buy a present!).
Any comments
Andrew
Device: N70
Version: V 2.0536.0.2 12-09-05 RM-84

I think this is by design. Not quite sure what the basis is of what is included and what is not. Items from the current day seem to show up in greater numbers than in future days.
All About Symbian - News, reviews and software for S60 phones.

Active Standby Pair Clustering.

Hi Chris, I had created ActiveStandby Pair as follows:
Server 1 => DSN: TTCluster1
Server 2 => DSN: TTCluster2.
Then I created ActiveStandby Pair in Server1, Started RepAgent and then Duplicated the DSN on Server 2 with name TTCluster 2. It worked fine.
Now to access it from the client server mode, I created Client DSN on Client machine using Virtual IP. (Using Linux Cluster Manager).
But inthis case I had to create two client DSN. TTCluster1Client and TTCluster2client. Since Application can connect to only one DSN and shifting to other while failover is very difficult.
So I am trying following model now, Let me know your views on this.
Server 1 and Server 2, both will have same DSN name "TTCluster".
Client Machin will have only one DSN "TTClusterClient" using VIP.
When the Server1 failes, Server 2 will take over and there is no need of shifting client DSN. Application will be routed to Server 2 after switch over.
Step1: created server DSN "TTCluster" on Server 1 and Server 2.
Step2: created user 'ttcluster' on Server 1 and Server 2.
Step3: Create DataStore TTCluster on Server 1. (By connecting to TTCluster).
Step4: Create Cache Groups (AWT) on Server1.
Step5: Started Cache Agent on Server1.
Step6: Created ActiveStandby Pair on Server1 as follows:
CREATE ACTIVE STANDBY PAIR
TTCluster ON "wabtectimesten.patni.com",
TTCluster ON "wabtectimesten2.patni.com"
RETURN TWOSAFE
STORE TTCluster PORT 20000 TIMEOUT 120;
Step8: executed ttrepstateset('ACTIVE') on server1.
Step9: Started Replication Agent on Server1.
Step10: Duplicated DataStore on Server2.
Issues:
Server2 is not coming up as Standby. The log on Server1 shows following messages:
15:19:33.83 Warn: REP: 8671: TTCLUSTER:receiver.c(1723): TT16060: Failed to read data from the network. select() timed out
15:19:37.09 Err : REP: 8671: TTCLUSTER:receiver.c(3428): TT16142: Failed to retrieve peer information. No peers found
15:19:37.09 Err : REP: 8671: TTCLUSTER:transmitter.c(5523): TT16229: Transmitter thread failure due to lack of state consistency at subscriber store _ORACLE
Question:
While creating replication scheme I have mentioned.
STORE TTCluster PORT 20000 TIMEOUT 120;
I need to define the timeout for both DataStores. How will I do that?
The above timeout will be applicable for which datastore??
Can you please let me know if I am going in the right direction???

Hi Tanweer,
When designing a monitoring scheme for TimesTen one has to bear a few things in mind (though not all will be relevant in every case):
1. There could be multiple 'instances' of TimesTen installed on a machine. Each instance is completely independent and must be monitoried separately.
2. Each instance has a 'main daemon' (timestend) that is the instance master supervisor. If this daemon is running and healthy then the 'instance' is considered to be 'up' and 'healthy'.
3. Each instance can manage multiple datastores. Each datastore is independent from the others and so each datastore must be monitored separately.
4. Each datastore may be using replication and/or cache connect. If so, these must also be monitored as well as the datastore since it is perfectly possible e.g. for the datastore to be healthy but for replication to be 'down'.
Depending on your requirements, your monitoring mechanism must 'model' this structure and relationships...
- If the instance main daemon is not running, or is not responding, then the entire instance is 'down' and all datastores managed by the instance should also be considered as 'down'
- If a datastore goes down (e.g. call invalidate), other stores in the instance are not affected and neither is the main daemon for the instance. They will continue to operate normally.
- A datastore may be healthy in itself but maybe replication or cache connect for the datastore is not healthy. Do you then consider the datastore as down? That depends on your applications requirements!
Hopefully this helps to clarify the interrelationship of components. Crashing a datastore by calling 'invalidate' does not crash the daemon (if it does then that is a bug!).
For monitoring the instance (main daemon) there are a few options:
1. ps -ef | grep timestend. This can detect if the daemon process is running but not if it is healthy...
2. Connect to a datastore. Every connect/disconnect request is processed via the main daemon so if the daemon is not healthy this will result in some error (usually a 'cannot communicate with the daemon' error). However, connect/disconnect are relatively expensive so you don't want to do this too often.
3. Have a monitoring process that maintains an open connection to the instance level datastore (DSN=TT_<instancename>). Periodically (as often as required within reason) it can execute the built in procedure ttDataStoreStatus() passing it the pathname of the instaance datastore checkpoint files (obtainable from the built in procedure ttConfiguration). This procedure communicates with the main daemon so will either return success (meaning daemon is okay) or an error (daemon is in big trouble).
If you have to do the test from a script then I would suggest that (2) is best but if you can do it from a continually running monitoring process then (3) is better.
For monitoring a datastore the best way to ascertain overall health is as follows:
1. Have a dummy table in the datastore. And as part of the check update a row in th dummy and commit the transaction. If this returns success then this shows that the datastore is up and able to service update requests (which means it is also okay for read requests).
2. You should also monitor the available space in the datastore and warn someone or something if the free space gets too low. You can query space allocation, current usage and high watermark usage from the SYS.MONITOR table. You can also configure TimesTen to generate SNMP traps and/or return warnings to applications if space usage exceeds some configured threshold. The objective is to take proactive action to prevent the datastore becoming full since that will require more disruptive corrective action.
For monitoring replication you should periodically:
1. Check that the datastore's repagent is running (you can do this using ttDatastoreStatus)
2. Check the status of each replication peer by calling ttReplicationStatus and checking the values of pstate (should be 'start') logs (if this value increases over time then the peer is in some kind of trouble) and lastMsg (if there is no message from the peer for a long time then it may be in some kind of trouble).
3. Sometimes an easier way is to have a dummy table set up for synchronous replication and do an update+commit for a row in that table. if replicatioin is working the commit will return within a few ms at most. If you get a timeout error returned that tells you that replication is in trouble,
To monitor cache connect is not so easy at present.
For AWT cache groups, the same monitoring as is used for replication is okay).
For SWT cache groups, if the sync to Oracle is not working every commit will get an error (so that's kind of obvious).
For AUTOREFRESH cache groups it's a bit harder. There is currenyly no supported way to determine when the last successful autorefresh occurred. I am hoping this capability will be added in a future release.
Sorry if that is a bit long winded - I hope it helps...
Chris

6500 SLIDE THE WORST PHONE EVER!

Does anyone used the Nokia 6500 Slide in here? Because I had so many problem on this phone, 2 weeks when I just had the phone screen when white blank on me while im talking on the phone or text message then several months later phone start to be slow till the phone I can't even play any music on my phone. I'm so sick this model because so many people I know brought this model having so many issued like me. So one suggest don't buy this model...

Hi,
Have you updated your phone? There is a new version for it - v8.30. You can check your current version by pressing *#0000# on the standby screen.
Try updating your phone's firmware by clicking to this link below:
http://europe.nokia.com/A4579163
Make sure you meet the system requirements before proceeding and backup some of your important contents.
If the phone still does not show any improvement, I suggest you to send the phone to the Nokia Care Centre near you.
Good luck

6500 Slide Active Standby Question

Similar Messages

Maybe you are looking for